Functionalization of surface‐grafted polymethylhydrosiloxane thin films with alkyl side chains

Thin films of crosslinked polymethylhydrosiloxane (PMHS) have been grafted on silica using the sol–gel process allowing further functionalization by effective quantitative hydrosilylation of SiH groups by olefins within the network. Postfunctionalization gives the polysiloxane network with n‐alkyl side chains. The PMHS coating was prepared by room temperature polycondensation of a mixture of methyldiethoxysilane HSiMe(OEt)₂ monomer and triethoxysilane HSi(OEt)₃ (TH) as crosslinker. The surface‐attached films are chemically stable and covalently bonded to the silica surface. Subsequently, films were functionalized without delamination. We showed by FTIR spectroscopy how the crosslinking ratio and the molecular size of the alkenes precursors influence the extent of the hydrosilylation reaction of SiH groups in the PMHS network. We have determined that quasi‐full olefin addition catalyzed by a platinum complex occurred within soft networks of less than 5% TH with 1‐alkenes CH₂?CH(CH₂)_n‐2CH₃ of various alkyl chain lengths (n = 5, 11, 17). Powders of PMHS gel were also modified with 1‐alkenes by hydrosilylation. The SiH groups within the soft gel (5% crosslinked) were fully functionalized as shown by ²⁹Si and ¹H solid‐state NMR. The structure of functionalized polysiloxane with n‐octadecyl and n‐dodecyl side chains was studied by FTIR, wide angle X‐ray diffraction, and DSC showing crystallization of the long n‐alkyl chains in the network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3546–3562, 2008     

Soft nanoparticles assembled from linear poly(ethylene glycol) and linear brush polydimethylsiloxane diblock copolymers

A series of novel amphiphilic diblock copolymers composed of hydrophilic linear poly(ethylene glycol) (PEG) and linear brush hydrophobic polydimethylsiloxane (PDMS) were synthesized. Three different molecular weights of monomethyl ether PEG were initially functionalized with 2‐bromoisobutyryl bromide to afford macroinitiators suitable for atom‐transfer radical polymerization. The macroinitiators were characterized by gel permeation chromatography, ¹H and ¹³C nuclear magnetic resonance spectroscopic analysis and matrix‐assisted laser desorption ionization time‐of‐flight mass spectroscopy. The three different molecular weight macroinitiators were then chain extended with monomethacryloxypropyl‐terminated PDMS and photoactive 2‐(methylacyloyloxy)ethyl anthracene‐9‐carboxylate in different molar ratios to afford a series of photoresponsive amphiphilic diblock copolymers with high conversions. Self‐assembly of these linear–linear brush diblock copolymers in N,N‐dimethylformamide afforded nanoparticles with hydrodynamic diameters (d_H) ranging from 41 to 268 nm, as determined by dynamic light scattering analysis. Crosslinking and stabilization of the nanoparticles was achieved via [4+4] photodimerization of the anthracene moieties upon exposure to UV radiation at 365 nm with the reverse reaction studied at a wavelength of 254 nm. Transmission electron microscopy revealed that the self‐assembled nanoparticles and their crosslinked derivatives had spherical morphologies. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1251–1262     

Block copolystyrene derivatives having flexible alkylsulfonated side chains and hydrophobic alkoxy chains as a proton exchange membrane for fuel cell application

A series of block copolystyrene derivatives, poly{[4‐(4‐sulfobutyloxy)styrene]_x‐block‐[4‐(n‐butoxystyrene)]_y} (PSBOS_x‐b‐PnBOS_y), containing a flexible alkylsufonated side chain and hydrophobic alkoxy chain with various ion exchange capacities (IECs) have been synthesized based on living anionic polymerization. The resulting crosslinked membranes were prepared using 4,4′‐methylene‐bis[2,6‐bis(hydroxyethyl)phenol] as the crosslinker in the presence of methanesulfonic acid. The crosslinked PSBOS_2.2‐b‐PnBOS₁ membrane with IEC of 2.89 mequiv g^?1 displays a high proton conductivity (0.01 S cm^?1) at 30% relative humidity and 80 °C, which is comparable to that of Nafion. The well‐developed phase separation and the continuous hydrophilic domains in the crosslinked PSBOS_2.2‐b‐PnBOS₁ membranes have been observed in a transmission electron microscope image. Moreover, the dynamic mechanical analysis measurement and Fenton's reagent testing show that the crosslinked PSBOS_x‐b‐PnBOS_y membranes have good mechanical properties and oxidative stability. These results indicate that the introduction of flexible alkylsulfonated side chains to the polystyrene main chains positively affect both the proton conductivity and oxidative stability. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Gold nanoparticle‐incorporated core and shell crosslinked micelles fabricated from thermoresponsive block copolymer of N‐isopropylacrylamide and a novel primary‐amine containing monomer

A novel primary amine‐containing monomer, 1‐(3′‐aminopropyl)‐4‐acrylamido‐1,2,3‐triazole hydrochloride (APAT), was prepared from N‐propargylacrylamide and 3‐azidopropylamine hydrochloride via copper‐catalyzed Huisgen 1,3‐dipolar cycloaddition (click reaction). Poly(N‐isopropylacrylamide)‐b‐poly(1‐(3′‐aminopropyl)‐4‐acrylamido‐1,2,3‐triazole hydrochloride), PNIPAM‐b‐PAPAT, was then synthesized via consecutive reversible addition‐fragmentation chain transfer polymerizations of N‐isopropylacrylamide and APAT. In aqueous solution, the obtained thermoresponsive double hydrophilic block copolymer dissolves molecularly at room temperature and self‐assembles into micelles with PNIPAM cores and PAPAT shells at elevated temperature. Because of the presence of highly reactive primary amine moieties in PAPAT block, two types of covalently stabilized nanoparticles namely core crosslinked and shell crosslinked micelles with ‘inverted’ core‐shell nanostructures were facilely prepared upon the addition of glutaric dialdehyde at 25 and 50 °C, respectively. In addition, the obtained structure‐fixed micelles were incorporated with gold nanoparticles via in situ reduction of preferentially loaded HAuCl₄. High resolution transmission electron microscopy revealed that gold nanoparticles can be selectively loaded into the crosslinked cores or shells, depending on the micelle templates employed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6518–6531, 2008     

Nanoprecipitation for ultrafiltration membranes

Polymer nanoparticles are readily obtainable by rapidly mixing a dilute polymer solution and a poor solvent. The nanoparticles of poly(vinylphenol), poly(vinylidene fluoride), and emeraldine base polyaniline prepared by nanoprecipitation become sticky when their diameters decrease down to a few tens of nanometers, and such polymer nanoparticles spontaneously assemble into rigid fractal networks of the nanoparticles. By filtering these fibrous nanoparticle networks on a microfiltration membrane, ultrafiltration membranes with a thin free‐standing filter cake layer made of nanoparticles are obtainable. The nanoparticle membranes are robust at least up to the applied pressure of 2 MPa and can separate 99% of 10 nm Au nanoparticles from the aqueous dispersion at the flux of more than 1835 L m^?2 h^?1 even at very low pressure difference of 0.08 MPa. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 615–620     

Molecular architecture and rheological characterization of novel intramolecularly crosslinked polystyrene nanoparticles

Novel polystyrene nanoparticles were synthesized by the controlled intramolecular crosslinking of linear polymer chains to produce well‐defined single‐molecule nanoparticles of varying molecular mass, corresponding directly to the original linear precursor chain. These nanoparticles are ideal to study the relaxation dynamics/processes of high molecular mass polymer melts, as the high degree of intramolecular crosslinking potentially inhibits entanglements. Both the nanoparticles and their linear analogs were characterized by measuring their intrinsic viscosity, hydrodynamic radius (R_h), and radius of gyration (R_g). The ratio R_g/R_h was computed to characterize the molecular architecture of the nanoparticles in solution, revealing a shift toward the constant density sphere limit with increasing crosslink density and molecular mass. Further, confirming particulate behavior, Kratky plots obtained from neutron scattering data show a shift toward particle‐like nature. The rheological behavior of the particles was found to be strongly dependent on both the extent of intramolecular crosslinking and molecular mass, with a minimal viscosity change at low crosslinking levels and a gel‐like behavior evident for a large degree of crosslinking. These and other results suggest the presence of a secondary mode of polymer relaxation/movement besides reptation, which in this case, is influenced by the total number of crosslinked loops present in the nanoparticle. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1930–1947, 2006     

Spinodal decomposition in N‐isopropylacrylamide gel

Spinodal decomposition in a chemically crosslinked N‐isopropylacrylamide (NIPA) polymer gel was investigated using turbidity and ultrasonic techniques. The turbidity of the quenched NIPA gel was measured over five orders of magnitude of timescales. With an increase of time, the gel transfers from a transparent and swollen gel to a cloudy and inhomogeneous gel, and eventually to a transparent and collapsed gel. The first transformation is a rapid process that only involves local arrangement of the polymer network and solvent into dilute and dense domains. The second transformation is a very slow process that involves global arrangement of the polymer network and solvent. The characteristic time for disappearance of the turbidity is proportional to the linear size squared at a constant temperature above T_c and increases exponentially as a function of the quenching depth of T ? T_c. By probing the movement of domains, a possible time‐dependent gel structure in the spinodal decomposition region is presented. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2168–2174, 2001     

Preparation of monodisperse nanoparticles containing poly(propylene imine)(NH2)32‐polystyrene

Polypropylenimine dendrimer (DAB‐Am‐32, generation 4.0) was converted into a macroinitiator DAB‐Am‐32‐Cl via reaction with 2‐chloropropionyl chloride. Monodisperse nanoparticles containing poly(propylene imine)(NH₂)₃₂‐polystyrene were prepared by emulsion atom transfer radical polymerization (ATRP) of styrene (St), using the DAB‐Am‐32‐Cl/CuCl/bpy as initiating system. The structure of macroinitiator was characterized by FTIR spectrum, ¹H NMR, and ¹³C NMR. The structure of poly(propylene imine)(NH₂)₃₂‐polystyrene was characterized by FT‐IR spectrum and ¹H NMR; the molecular weight and molecular weight distribution of poly(propylene imine)(NH₂)₃₂‐polystyrene were characterized by gel permeation chromatograph (GPC). The morphology, size and size distribution of the nanoparticles were characterized by photon correlation spectroscopy (PCS), transmission electron microscopy (TEM), and atomic force microscopy (AFM). The effects of monomer/macroinitiator ratio and surfactant concentration on the size and size distribution of the nanoparticles were investigated. It was found that the diameters of the nanoparticles were smaller than 100 nm (30–80 nm) and monodisperse; moreover, the particle size could be controlled by monomer/macroinitiator ratios and surfactant concentration. With the increasing of the ratio of St/DAB‐Am‐32‐Cl, the number‐average diameter (D_n), weight‐average diameter (D_w) were both increased gradually. With enhancing the surfactant concentration, the measured D_h of the nanoparticles decreased, while the polydispersity increased. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2892–2904, 2009     

Conductivity,proton percolation,and gelation during the network growth in a flexible chain diepoxide and diamine mixture

The conductivity of a stoichiometric mixture of diglycidyl ether of 1,4‐butanediol and 1,6‐hexamethylene diamine has been studied during its polymerization at several temperatures where the ultimate product is a crosslinked gel. The decrease in the dc conductivity, σ₀, with the polymerization time, t, fits an equation for bond percolation, σ₀ ∼ [(t_gel‐t)/t_gel]^p, and yields a gelation time, t_gel which agrees with the t_gel determined from the viscosity and shear modulus measurements. It is proposed that as one covalent bond forms on chemical reaction, an indeterminable number of intermolecular H‐bonds in the structure vanish, and protonic conduction is disrupted. Thus, as the original H‐bond network gives way to a covalently bonded network, the mechanical rigidity increases, and protonic conductivity decreases. The gel point is reached when the increase in the number of covalent bonds brings the liquid's state up to its rigidity percolation threshold, and the decrease in the number of H‐bonds brings it down to its electrical percolation threshold. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 122–126, 2000     

Facile synthesis,characterization, and potential applications of two kinds of polymeric pH indicators: Phenolphthalein formaldehyde and o‐cresolphthalein formaldehyde

Two kinds of applicable polymeric pH indicators were synthesized by the reaction of phenolphthalein and o‐cresolphthalein with formaldehyde under alkaline conditions by a one‐pot method. The synthesized products were fully characterized with Fourier transform infrared, ¹H NMR, ultraviolet–visible spectroscopy, and gel permeation chromatography. The results indicated that the reaction was a typical phenol formaldehyde reaction. The dosage of formaldehyde and the reaction time were well controlled to obtain soluble polymers, instead of crosslinked products. The polymeric‐pH‐indicator‐immobilized poly(vinyl alcohol) (PVA) membranes were easily fabricated and had good long‐term stability under highly basic conditions and a fast equilibrium response. Moreover, the phenolphthalein formaldehyde immobilized PVA membrane had a linear response from pH 10.0 to 14.0, and so it has promise as a optical transducer for high pH value determinations. The o‐cresolphthalein formaldehyde immobilized PVA membrane had a nonlinear response from pH 9.0 to 13.0. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1019–1027, 2005     

Thermoresponsive hydrogel of poly(glycidyl methacrylate‐co‐N‐isopropylacrylamide) as a nanoreactor of gold nanoparticles

The synthesis of a thermoresponsive hydrogel of poly(glycidyl methacrylate‐co‐N‐isopropylacrylamide) (PGMA‐co‐PNIPAM) and its application as a nanoreactor of gold nanoparticles are studied. The thermoresponsive copolymer of PGMA‐co‐PNIPAM is first synthesized by the copolymerization of glycidyl methacrylate and N‐isopropylacrylamide using 2,2′‐azobis(isobutyronitrile) as an initiator in tetrahydrofuran at 70 °C and then crosslinked with diethylenetriamine to form a thermoresponsive hydrogel. The lower critical solution temperature (LCST) of the thermoresponsive hydrogel is about 50 °C. The hydrogel exists as 280‐nm spheres below the LCST. The diameter of the spherical hydrogel gradually decreases to a minimum constant of 113 nm when the temperature increases to 75 °C. The hydrogel can act as a nanoreactor of gold nanoparticles because of the coordination of nitrogen atoms of the crosslinker with gold ions, on which a hydrogel/gold nanocomposite is synthesized. The LCST of the resultant hydrogel/gold nanocomposite is similar to that of the hydrogel. The size of the resultant gold nanoparticles is about 15 nm. The hydrogel/gold nanocomposite can act as a smart and recyclable catalyst. At a temperature below the LCST, the thermoresponsive nanocomposite is a homogeneous and efficient catalyst, whereas at a temperature above the LCST, it becomes a heterogeneous one, and its catalytic activity greatly decreases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2812–2819, 2007     

Facile Synthesis and in situ TEM Observation of Nanoporous Pd for Enhanced Catalytic Applications

A facile, efficient and green photochemical synthetic approach has been used to prepare sponge‐like porous Pd nanoparticles. Obtained by ultraviolet irradiation using a K₂PdCl₄ precursor solution, the final products exhibited three dimensionally interconnected porous structures made up of ~3.6 nm sized Pd nanoparticles. In situ liquid cell TEM results indicated such porous structures are in a dynamic stable state when the particles are distributed in aqueous solution. The porous Pd nanoparticles exhibited electrochemical active surface area (ECSA) of up to 43 m²·g^–1 and mass activity of 1144 mA·mg^–1 in menthol oxidation, k_app of 0.22 min^–1 and normalized k_app/m (k_n) of 8.3×10⁴ min^–1·g^–1 in 4‐nitrophenol (4‐NP) reduction reactions. Comparing with the literature, it is demonstrated that our porous Pd nanoparticles with clean surfaces exhibited very high catalytic performances. This work may shed a light on facile and green synthesis of noble‐metal particles with better catalytic performances.     

Anisotropic Self‐Assembly of Citrate‐Coated Gold Nanoparticles on Fluidic Liposomes

The behavior of self‐assembly processes of nanoscale particles on plasma membranes can reveal mechanisms of important biofunctions and/or intractable diseases. Self‐assembly of citrate‐coated gold nanoparticles (cAuNPs) on liposomes was investigated. The adsorbed cAuNPs were initially fixed on the liposome surfaces and did not self‐assemble below the phospholipid phase transition temperature (T_m). In contrast, anisotropic cAuNP self‐assembly was observed upon heating of the composite above the T_m, where the phospholipids became fluid. The number of self‐assembled NPs is conveniently controlled by the initial mixing ratio of cAuNPs and liposomes. Gold nanoparticle protecting agents strongly affected the self‐assembly process on the fluidic membrane.     

Fabrication and characterization of SiO2/PVDF composite nanofiber‐coated PP nonwoven separators for lithium‐ion batteries

SiO₂/polyvinylidene fluoride (PVDF) composite nanofiber‐coated polypropylene (PP) nonwoven membranes were prepared by electrospinning of SiO₂/PVDF dispersions onto both sides of PP nonwovens. The goal of this study was to combine the good mechanical strength of PP nonwoven with the excellent electrochemical properties of SiO₂/PVDF composite nanofibers to obtain a new high‐performance separator. It was found that the addition of SiO₂ nanoparticles played an important role in improving the overall performance of these nanofiber‐coated nonwoven membranes. Among the membranes with various SiO₂ contents, 15% SiO₂/PVDF composite nanofiber‐coated PP nonwoven membranes provided the highest ionic conductivity of 2.6 × 10^?3 S cm^?1 after being immersed in a liquid electrolyte, 1 mol L^?1 lithium hexafluorophosphate in ethylene carbonate, dimethyl carbonate and diethyl carbonate. Compared with pure PVDF nanofiber‐coated PP nonwoven membranes, SiO₂/PVDF composite fiber‐coated PP nonwoven membranes had greater liquid electrolyte uptake, higher electrochemical oxidation limit, and lower interfacial resistance with lithium. SiO₂/PVDF composite fiber‐coated PP nonwoven membrane separators were assembled into lithium/lithium iron phosphate cells and demonstrated high cell capacities and good cycling performance at room temperature. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1719–1726     

DABCO‐functionalized polysulfones as anion‐exchange membranes for fuel cell applications: Effect of crosslinking

A series of DABCO‐functionalized polysulfones were synthesized and characterized. The effect that crosslinking has on the membrane properties containing different degrees of functionalization was evaluated. These polymers showed good thermal stability below the fuel cell operation temperature, T < 100 °C, reflected by the T_OD, T_FD, and thermal durability. The water uptake increased as the percentage of DABCO groups increased and the crosslinked membranes showed lower capacity to absorb water than the non‐crosslinked ones favoring thus the dimensional stability of the first ones. Membranes in the chloride form containing low degree of functionalization exhibited the highest tensile strength values. The ionic conductivity of non‐crosslinked membranes varied as a function of the functionalization degree until a value of around 100% achieving a maximum value at 86%. However, the crosslinked ones showed satisfactory ionic conductivities for values higher than 100%. The behavior of these polymeric materials in alkaline solutions revealed a great alkaline stability necessary to be used as solid electrolytes in fuel cells. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1326–1336     

Branching by reactive end groups. III. Synthesis,branching, and analysis of m‐ethynylphenol/p‐t‐butylphenol‐coterminated bisphenol a polycarbonates

The use of m‐ethynylphenol (m‐EP) and p‐t‐butylphenol (PTBP) as coterminators for bisphenol A polycarbonates (BA PCs) provided long‐chain‐branched PCs, partially crosslinked PCs, or both after the thermal reaction of the terminal m‐EP groups, depending on the molar ratio of the chain terminators. Linear m‐EP/PTBP PCs were prepared by solution phosgenation of BA and the two coterminators. Differential scanning calorimetry showed the onset of the m‐EP‐end‐group reaction at about 250 °C by the appearance of a reaction exotherm. The enthalpy (ΔH) of this reaction was roughly proportional to the amount of m‐EP in the PC and to an extent could be used to monitor the progress of the reaction and estimate its kinetics. A complete m‐EP‐end‐group reaction was evident from gel permeation chromatography analysis upon heating under N₂ to 380 °C for 10 min or 360 °C for 60 min. The amount, if any, of gel formed after the m‐EP‐end‐group reaction depended on X_EP; those PCs with a X_EP value less than or equal to 0.33 had little or no gel. The maximum X_EP that precluded the formation of gels after branching was estimated to be about 0.45–0.48. The molecular weight of m‐EP/PTBP PCs increased after branching, as evidenced by gel permeation chromatography analysis. Assuming that the terminal m‐EP groups had a statistical distribution on the polymer chain ends and that they underwent only homopolymerization, the average reacted m‐EP‐group functionality according to estimated gel‐point composition was about 2.8–3.0. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2352–2358, 2000     

Nanoparticle Size‐Fractionation through Self‐Standing Porous Covalent Organic Framework Films

Covalent organic frameworks (COFs) have attracted attention due to their ordered pores leading to important industrial applications like storage and separation. Combined with their modular synthesis and pore engineering, COFs could become ideal candidates for nanoseparations. However, the fabrication of these microcrystalline powders as continuous, crack‐free, robust films remains a challenge. Herein, we report a simple, slow annealing strategy to construct centimeter‐scale COF films ( Tp‐Azo and Tp‐TTA ) with micrometer thickness. The as‐synthesized films are porous (SA_BET=2033 m² g^?1 for Tp‐Azo ) and chemically stable. These COFs have distinct size cut‐offs (ca. 2.7 and ca. 1.6 nm for Tp‐Azo and Tp‐TTA , respectively), which allow the size‐selective separation of gold nanoparticles. Unlike, other conventional membranes, the durable structure of the COF films allow for excellent recyclability (up to 4 consecutive cycles) and easy recovery of the gold nanoparticles from the solution.     

Solid polymer electrolytes I,preparation, characterization,and ionic conductivity of gelled polymer electrolytes based on novel crosslinked siloxane/poly(ethylene glycol) polymers

A series of crosslinked siloxane/poly(ethylene glycol) (Si–PEG) copolymers were synthesized from the reactive methoxy‐functional silicone resin (Si resin) and PEGs with different molecular weights via two kinds of crosslinking reactions during an in situ curing stage. One of the crosslinking reactions is the self‐condensation between two methoxy groups in the Si resin, and another one is an alkoxy‐exchange reaction between the methoxy group in the Si resin and the OH group in PEG. The synthesized crosslinked copolymers were characterized by Fourier transform infrared spectroscopy, DSC, and ¹³C NMR. The crosslinked copolymers were stable in a moisture‐free environment, but the Si? O? C linkages were hydrolyzed in humid conditions. The gel‐like solid polymer electrolytes (SPEs) were prepared by impregnating these crosslinked Si–PEG copolymers in a propylene carbonate (LiClO₄/PC) solution. The highest conductivity reached 2.4 × 10^?4 S cm^?1 at 25 °C and increased to 8.7 × 10^?4 S cm^?1 at 85 °C. The conductivities of these gel‐type SPEs were affected by the content of LiClO₄/PC, the molecular weights of PEGs, and the weight fraction of the Si resin. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2051–2059, 2004     

Photo‐crosslinked fluorinated thin films from azido‐functionalized random copolymers

Random copolymers of styrene, p‐azidomethylstyrene and 1H,1H,2H,2H‐perfluorodecyl methacrylate were prepared in two steps involving nitroxide‐mediated radical copolymerization and azidation reaction and further characterized by ¹H and ¹⁹F NMR, size exclusion chromatography, differential scanning calorimetry, and thermal gravimetric analysis. Ultrathin films of these azidomethyl‐functionalized fluorinated random copolymers, with thicknesses ranging from 20 to 100 nm, were spin coated onto Si substrates and then crosslinked by ultraviolet irradiation resulting in smooth and insoluble crosslinked fluorinated polymer mats. The surface properties of the supported thin films were investigated by X‐ray photoelectron spectroscopy and water contact angle measurements. These tailored photo‐crosslinked coatings afford a versatile control and homogenization of the wetting properties of different organic and inorganic substrates. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3888–3895, 2010