Enhanced thermal conductivity of rheologically percolated carbon nanofiber reinforced polypropylene composites

Three different types of carbon nanofibers (CNF) were incorporated in the same polypropylene (PP) matrix by twin‐screw extrusion. The rheological and thermal properties were investigated. The rheological characterization of CNFs/PP composites as function of their volume fraction shows different microstructures: percolated and non‐percolated behaviors of their CNF's networks. In this work, the laser flash technique is employed in the experimental determination of the thermal diffusivity and conductivity of composites at room temperature. The ultimate aim is to correlate microstructure described by rheological analysis with final thermal properties. The results show that thermal diffusivity and conductivity are clearly higher for rheologically percolated composites suggesting that above certain critical content of nanofibers thermal transport is mainly controlled by percolated structures caused by interconnected CNFs' networks. Finally, thermal conductivity results are described by means of percolation theory from which an intrinsic thermal conductivity for the CNFs' network of approximately 6.5 W/m K, i.e. close to three times lower than some values reported in literature for SWCNTs' networks, was calculated. Copyright © 2015 John Wiley & Sons, Ltd.     

Ethylene–acrylic acid copolymer induced electrical conductivity improvements and dynamic rheological behavior changes of polypropylene/carbon black composites

The experimental data reveal that the addition of ethylene–acrylic acid copolymer (EAA) into carbon black (CB)/polypropylene (PP) composites can improve the electrical conductivity of CB/PP composites by two to six orders of magnitude at a comparatively low CB content (φ), and when φ = 2.5 vol %, 60/40 of PP/EAA is an optimum for electrical conductivity improvement. The dynamic rheological data show that with increasing φ there are apparent rheological percolations for CB/PP composites. A modified Kerner–Nielson equation can be used to describe the correlation between electrical percolation and dynamic viscoelastic percolation. The addition of EAA into CB/PP composites leads to apparent changes in dynamic rheological behaviors. When φ = 2.5 vol %, a rheological percolation appears in CB/PP/EAA (CPE) composites with increasing EAA content. The similar rheological behaviors correspond to the similar morphological structures for CPE composites with φ = 5.0 vol %. The appearance of bumps in the van‐Gurp–Palmen plots corresponds to the formation of network structure in CB/PP and CPE composites, and the more perfect the networks, the higher the amplitude of the bumps. All data indicate that the van‐Gurp–Palmen plot is sensitive to the formation of filler particle networks or cocontinuous phase which spans the whole composite. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1762–1771, 2009     

Annealing induced electrical conductivity jump of multi‐walled carbon nanotube/polypropylene composites and influence of molecular weight of polypropylene

Multi‐walled carbon nanotube (MWCNT)/polypropylene (PP) composites were prepared by a micro melt mixing process. As‐prepared composites had relatively low electrical conductivity due to the disruption of MWCNT network by strong shear. The electrical conductivity jumped to high values throughout an annealing process above the melting temperature of PP. The significant enhancement of electrical conductivity was influenced by annealing time, temperature, and content of MWCNTs. In particular, molecular weight of PP played an important role in affecting the conductivity enhancement. The molecular weight of PP was varied from 190,000 to 340,000 to examine its effect on the electrical conductivity. By comparing the conductivity enhancement behavior of composites with different molecular weight PPs and observing the morphology evolution during annealing, it was found that reaggregation of MWCNTs and the subsequent formation of MWCNT network during annealing are the main reasons for the jump of electrical conductivity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Aspect ratio effects of multi‐walled carbon nanotubes on electrical,mechanical, and thermal properties of polycarbonate/MWCNT composites

Two multi‐walled carbon nanotubes (MWCNTs) having relatively high aspect ratios of 313 and 474 with approximately the same diameter were melt mixed with polycarbonate (PC) in a twin‐screw conical micro compounder. The effects of aspect ratio on the electrical, mechanical, and thermal properties of the PC/MWCNT composites were investigated. Electrical conductivities and storage moduli of the filled samples are found to be independent of the starting aspect ratio for these high aspect ratio tubes; although the conductivities and storage moduli are still significantly higher than values of composites made with nanotubes having more commercially common aspect ratios of ～100. Transmission electron microscopy results suggest that melt‐mixing reduces these longer nanotubes to the same length, but still approximately two times longer than the length of commercially common aspect ratio tubes after melt‐mixing. Molecular weight measurements show that during melt‐mixing the longer nanotubes significantly degrade the molecular weight of the polymer as compared to very similar nanotubes with aspect ratio ～100. Because of the molecular weight reduction glass transition temperatures predictably show a large decrease with increasing nanotube concentration. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 73–83     

Epoxy matrix composites reinforced with purified carbon nanotubes for thermal management applications

The role of carbon nanotube purification treatment as a means to improve the thermal properties of polymer matrix composites was investigated. Particular emphasis was placed on clarifying the processing‐property relationship in polymer composites for thermal management applications. The results indicated that purification treatment is critical to the thermal properties of derived polymer composites. Purification treatment can yield a twofold increase in composite thermal conductivity because of improved effectiveness in interfacial interaction and increased chemical purity of the filler. However, there is a trade‐off between the benefits and disadvantages associated with purification treatment, particularly when thermal and electrical properties are both concerned. Purification treatment gives rise to a sharp decrease in composite electrical conductivity by at least two orders of magnitude because of the lack of an effective percolating network. The effect of purification treatment on composite electrical properties is more significant than on its thermal properties.     

Effect of carbon nanofibers on mechanical and electrical behaviors of acrylonitrile‐butadiene rubber composites

Recently, carbon nanofibers have become an innovative reinforcing filler that has drawn increased attention from researchers. In this work, the reinforcement of acrylonitrile butadiene rubber (NBR) with carbon nanofibers (CNFs) was studied to determine the potential of carbon nanofibers as reinforcing filler in rubber technology. Furthermore, the performance of NBR compounds filled with carbon nanofibers was compared with the composites containing carbon black characterized by spherical particle type. Filler dispersion in elastomer matrix plays an essential role in polymer reinforcement, so we also analyzed the influence of dispersing agents on the performance of NBR composites. We applied several types of dispersing agents: anionic, cationic, nonionic, and ionic liquids. The fillers were characterized by dibutylphtalate absorption analysis, aggregate size, and rheological properties of filler suspensions. The vulcanization kinetics of rubber compounds, crosslink density, mechanical properties, hysteresis, and conductive properties of vulcanizates were also investigated. Moreover, scanning electron microscopy images were used to determine the filler dispersion in the elastomer matrix. The incorporation of the carbon nanofibers has a superior influence on the tensile strength of NBR compared with the samples containing carbon black. It was observed that addition of studied dispersing agents affected the performance of NBR/CNF and NBR/carbon black materials. Especially, the application of nonylphenyl poly(ethylene glycol) ether and 1‐butyl‐3‐methylimidazolium tetrafluoroborate contributed to enhanced mechanical properties and electrical conductivity of NBR/CNF composites.     

Relations between the aspect ratio of carbon nanotubes and the formation of percolation networks in biodegradable polylactide/carbon nanotube composites

The biodegradable polylactide composites containing carbon nanotubes (CNTs) with high aspect ratio (HAR) and low aspect ratio (LAR) were prepared by melt mixing. The physical properties of those two systems were characterized in terms of rheology, conductivity, and mechanical properties for establishing preliminary structure–property relations. Several viscoelastic models were then used to further describe the relations between aspect ratio and percolation network of CNTs. The results show that these two CNTs present different structural characteristics in the polylactide (PLA) matrix during melt mixing: the LAR CNTs are far stiffer than the HAR CNTs. At low loading levels, the former is dispersed as bent fibers or their small bundles, whereas the latter is dispersed as self‐entangled flocs, presenting far larger hydrodynamic radius than the former. At high loading levels, both are dispersed as flocs due to strong tube–tube interactions. However, the two CNTs show approximate average floc size and mesh size because they present same rigid length and effective aspect ratio. At identical loadings, therefore, the HAR CNTs have more total number of flocs than that of the LAR CNTs, forming network with more compact structure and imparting higher contributions to properties of the composites as a result. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 479–489, 2010     

New melt mixing polyethylene multiwalled carbon nanotube nanocomposites with very low electrical percolation threshold

The present work focuses on the study of the electrical properties of high‐density polyethylene (HDPE)/multiwalled carbon nanotube (MWCNT) nanocomposites. The samples were produced by melt mixing by diluting a masterbatch of HDPE/MWCNT using two types of mini‐extruders in order to see the influence of the shear processing on the electrical properties. The dielectric relaxation spectroscopy was used for the investigation of the electrical properties in the studied samples. The composites dc conductivity (σ_dc) follows the scaling low derivate from the percolation theory of the form σ_dc ~ (p ? p_c)^t. A low electrical percolation (p_c ≈ 0.3 ? 0.4 vol. %) was found in both cases. The critical exponent t had a value very close to the theoretical one for a percolation network in three dimensions (t ≈ 2). The analysis of the morphology of the nanocomposites showed a good and homogeneous dispersion of the fillers in the PE matrix. The effect of the incorporation of MWCNTs on the dynamic mechanical and thermal behaviors was also presented. The MWCNTs have improved the mechanical properties of the polyethylene matrix and increased the crystallization temperatures. Copyright © 2013 John Wiley & Sons, Ltd.     

Significant enhancement of electrical and thermal conductivities of polyethylene carbon nanotube composites by the addition of a low amount of silver nanoparticles

Electrically and thermally conductive high‐density polyethylene composites filled with hybrid fillers, multiwall carbon nanotubes (MWCNTs) and silver nanoparticles (Ag‐NPs), have been prepared in the melt state. The investigation of their electrical and thermal conductivities while comparing with high‐density polyethylene/MWCNT binary composites shows that the addition of only 3 vol% of Ag‐NPs does not reduce the electrical percolation threshold (P_c) that remains as low as 0.40 vol% of MWCNTs but leads to an increase in the maximum dc electrical conductivity of PE/MWCNT composites by two orders of magnitudes. Moreover, the association of both Ag‐NPs and carbon nanotube particles improved our composite's thermal conductivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Microstructure,electrical, and electromagnetic interference shielding properties of carbon nanotube/acrylonitrile–butadiene–styrene nanocomposites

Processing, electrical, and electromagnetic interference (EMI) shielding behaviors of carbon nanotube (CNT)/acrylonitrile–butadiene–styrene (ABS) nanocomposites were studied as function of CNT concentration. The nanocomposites were prepared by melt mixing followed by compression molding. The selective and good level of dispersion of CNT in the styrene–acrylonitrile section of the ABS polymer was found to create conductive networks in the ABS matrix at a nanofiller loading of 0.75 wt %. At this nanofiller loading, the nanocomposite electrical conductivity was 10^?5 S/m. This conductivity makes the nanocomposite suitable for electrostatic discharge protection applications. The EMI shielding effectiveness of the nanocomposites increased with the increase in nanofiller concentration. In the 100–1500 MHz frequency range, 1.1 mm thick plates made of ABS nanocomposite filled with 5 wt % CNT exhibit an EMI shielding effectiveness of 24 dB. At this shielding level, the nanocomposite is suitable for a broad range of applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Correlation between rheological,electrical, and microstructure characteristics in polyethylene/aluminum nanocomposites

Polyethylene (PE)/aluminum (Al) nanocomposites with various filler contents were prepared by a solution compounding method. We investigated the influence of the surface modification of Al nanoparticles on the microstructure and physical properties of the nanocomposites. The silane coupling agent octyl‐trimethoxysilane was shown to significantly increase interfacial compatibility between the polymer phase and Al nanoparticles. Rheological percolation threshold values were determined by analyzing the improvement in storage modulus at low frequencies depending on the Al loadings. Lower percolation threshold values were obtained for the composites prepared with the original nanoparticles than those prepared with the silane‐modified Al nanoparticles. A strong correlation between the time and concentration dependences of dc conductivity and rheological properties was observed in the different nanocomposite systems. The rheological threshold of the composites is smaller than the percolation threshold of electrical conductivity for both of the nanocomposite systems. The difference in percolation threshold is understood in terms of the smaller particle–particle distance required for electrical conduction when compared with that required to impede polymer mobility. It was directly shown by SEM characterization that the nanoparticle surface modification yielded better filler dispersion, as is consistent with our rheological and electrical analysis. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2143–2154, 2008     

Surface morphology and electrical properties of polyurethane nanofiber webs spray‐coated with carbon nanotubes

Multiwalled carbon nanotubes (MWNTs) were spray‐coated on electrospun polyurethane nanofiber webs for electrical conductive application. For the effective coating of MWNTs, hyperbranched polyurethane (HBPU) was used by blending with linear polyurethane, which was synthesized in the A₂ + B₃ approach using poly(ε‐caprolactone)diol, 4,4′‐methylene bis(phenylisocynate), and castor oil. SEM measurements showed that the MWNTs could be coated well along the surface of nanofibers when the HBPU was blended in the linear polyurethane nanofibers. Blending of HBPU in the nanofibers also affected the electrical conductivity of MWNT‐coated nanofiber webs. The low electrical resistance from 20 to 400 Ω/sq was obtained for MWNT‐coated nanofiber webs and their electrical resistance decreased with an increase of spraying frequency. As a potential application of MWNT‐coated nanofiber webs, the electrical heating effect because of applied voltage was demonstrated. Copyright © 2011 John Wiley & Sons, Ltd.     

Effects of processing conditions on rheological,thermal, and electrical properties of multiwall carbon nanotube/epoxy resin composites

We report on the effect of processing conditions on rheology, thermal and electrical properties of nanocomposites containing 0.02–0.3 wt % multiwall carbon nanotubes in an epoxy resin. The influence of the sonication, the surface functionalization during mixing, as well as the application of external magnetic field (EMF) throughout the curing process was examined. Rheological tests combined with optical microscopy visualization are proved as a very useful methodology to determine the optimal processing conditions for the preparation of the nanocomposites. The Raman spectra provide evidence for more pronounced effect on the functionalized with hardener compositions, particularly by curing upon application of EMF. Different chain morphology of CNTs is created depending of the preparation conditions, which induced different effects on the thermal and electrical properties of the nanocomposites. The thermal degradation peak is significantly shifted towards higher temperatures by increasing the nanotube content, this confirming that even the small amount of carbon nanotubes produces a strong barrier effect for the volatile products during the degradation. The ac conductivity measurements revealed lower values of the percolation threshold (pc) in the range of 0.03–0.05 wt %. CNTs for the nanocomposites produced by preliminary dispersing of nanotubes in the epoxy resin, compared to those prepared by preliminary functionalization of the nanotubes in the amine hardener. This is attributed to the higher viscosity and stronger interfacial interactions of the amine hardener/CNT dispersion which restricts the reorganization of the nanotubes. The application of the EMF does not influence the pc value but the dc conductivity values (σ_dc) of the nanocomposites increased at about one order of magnitude due to the development of the aforementioned chain structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Enhanced electrical and mechanical properties of multiwall carbon nanotube rubber composites

Multiwall carbon nanotube‐filled elastomers are prepared by solution blending using a sonication process. It is shown that the processing conditions have a strong effect on the composite properties especially on electrical properties, which are very sensitive to nanotube dispersion within the elastomeric matrix. The percolation threshold is seen to be shifted to a lower nanotube content than that previously reported. With regard to the unfilled elastomer, large increases in the elastic and tensile moduli are obtained with the nanotube loading, thus highlighting the potential of this type of particles as reinforcing fillers for elastomeric matrices. Raman spectroscopy under strain has been used to evaluate the strength of the polymer–filler interface. Weak interfacial interactions are deduced, but the debundling of the nanotubes and the orientational effects of the polymeric chains are observed when the composite is submitted to a uniaxial deformation. Copyright © 2012 John Wiley & Sons, Ltd.     

Rheological and electrical properties of polypropylene/MWCNT composites prepared with MWCNT masterbatch chips

Melt compounded PP/MWCNT (polypropylene/multi-walled carbon nanotube) composites were prepared by diluting highly concentrated masterbatch chips. Maleic anhydride grafted polypropylene (PP-g-MAH) was used as a compatibilizer to promote dispersion and interaction of MWCNTs. Rheological properties were investigated with respect to the MWCNT and compatibilizer loadings, and related to morphological and electrical properties. As the MWCNT loading was increased, shear viscosity and yield stress were increased at low shear rate region because of increased interaction between MWCNT particles. When the MWCNT loading was low, MWCNT dispersion was improved by the PP-g-MAH compatibilizer because MWCNTs were wetted sufficiently due to the presence of the compatibilizer. However, rheological and electrical properties of highly concentrated MWCNT composites with the compatibilizer were not improved compared with PP/MWCNT composites without the compatibilizer because the compatibilizer did not provide sufficient wrapping of MWCNT particles. Electrical and morphological properties of PP/MWCNT composites were correlated with the rheological properties in steady and dynamic oscillatory shear flows.     

Decoupling the effects of screw speed and particle surface functionality on the filler suspension state in PBS/fumed silica nanocomposites

This work assessed the relative effects of processing conditions and interfacial interactions on the structure and properties of PBS/fumed silica nanocomposites. Rheology and scattering were used to investigate the dispersion state of silica particles with different surface treatments in nanocomposites produced by ultra‐high speed twin‐screw extrusion. Structural parameters of the silica, such as fractal dimension and Fisher exponent, were estimated by low‐frequency rheology responses and lower q scattering data. This study demonstrates that both decreased bulk polymer properties and improved filler suspension caused by high shear compounding determine the final properties of these PBS based nanocomposites. While the molecular weight of bulk polymer matrix was significantly reduced, the extreme shear increased the probability of forming percolated clusters, leading to remarkable reinforcement (up to 4000%) as evidenced by the low‐frequency rheological response. Further, the improvement in dispersion was enhanced when the filler was functionalized with a compatibilizing surface treatment. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1820–1828     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

Nucleation ability of multiwall carbon nanotubes in polypropylene composites

The nonisothermal crystallization of multiwall carbon nanotube (MWNT)/isotactic polypropylene (iPP) nanocomposites was investigated. The results derived from the differential scanning calorimetry curves (onset temperature, melting point, supercooling, peak temperature, half‐time of crystallization, and enthalpy of crystallization) were compared with those of neat iPP. The data were also processed according to Ozawa's theory and Dobreva's approach. These results and X‐ray diffraction data showed that the MWNTs acted as α‐nucleating agents in iPP. Accordingly, MWNT/iPP was significantly different from neat iPP: A fibrillar morphology was observed instead of the usual spherulites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 520–527, 2003     

Carbon black,multiwall carbon nanotubes,expanded graphite and functionalized graphene flame retarded polypropylene nanocomposites

Herein, we examine the influence of adding functionalized graphene (FG), distinct expanded graphites and carbon nanofillers such as carbon black and multiwall carbon nanotubes on mechanical properties, morphology, pyrolysis, response to small flame and burning behavior of a V‐2 classified flame‐retarded polypropylene (PP). Among carbon fillers, FG and multilayer graphene (MLG) containing fewer than 10 layers are very effectively dispersed during twin‐screw extrusion and account for enhanced matrix reinforcement. In contrast to the other fillers, no large agglomerates are detected for PP‐FR/FG and PP‐FR/MLG, as verified by electron microscopy. Adding FG to flame‐retardant PP prevents dripping due to reduced flow at low shear rates and shifts the onset of thermal decomposition to temperatures 40°C higher. The increase in the onset temperature correlates with the increasing specific surface areas (BET) of the layered carbon fillers. The reduction of the peak heat release rate by 76% is attributed to the formation of effective protection layers during combustion. The addition of layered carbon nanoparticles lowers the time to ignition. The presence of carbon does not change the composition of the evolved pyrolysis gases, as determined by thermogravimetric analysis combined with online Fourier‐transformed infrared measurements. FG and well‐exfoliated MLG are superior additives with respect to spherical and tubular carbon nanomaterials. Copyright © 2013 John Wiley & Sons, Ltd.     

Preparation and properties of natural rubber composites reinforced with pretreated carbon nanotubes

In order to achieve dramatic improvements in the performance of rubber materials, the development of carbon nanotube (CNT)‐reinforced rubber composites was attempted. The CNT/natural rubber (NR) nanocomposite was prepared through solvent mixing on the basis of pretreatment of CNTs. Thermal properties, vulcanization characteristics, and physical and mechanical properties of the CNT/NR nanocomposites were characterized in contrast to the carbon black (CB)/NR composite. Through the addition of the CNTs treated using acid bath followed by ball milling with HRH (hydrated silica, resorcinol, and hexamethylene tetramine) bonding systems, the crystallization melting peak in differential scanning calorimetry (DSC) curves of NR weakened and the curing rate of NR slightly decreased. Meanwhile, the over‐curing reversion of CNT/NR nanocomposites was alleviated. The dispersion of the treated CNTs in the rubber matrix and interfacial bonding between them were rather good. The mechanical properties of the CNT‐reinforced NR showed a considerable increase compared to the neat NR and traditional CB/NR composite. At the same time, the CNT/NR nanocomposites exhibited better rebound resilience and dynamic compression properties. The storage modulus of the CNT/NR nanocomposites greatly exceeds that of neat NR and CB/NR composites under all temperature regions. The thermal stability of NR was also obviously improved with the addition of the treated CNTs. Copyright © 2008 John Wiley & Sons, Ltd.