Synthesis and photovoltaic properties of conjugated copolymers based on benzimidazole and various thiophene

A new accepter unit, dimethyl‐2H‐benzimidazole, was prepared and used for the synthesis of the conjugated polymers containing electron donor–acceptor pair for organic photovoltaics (OPVs). Dimethyl‐2H‐benzimidazole unit was designed to substitute the BT unit of poly(N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)) (PCDTBT). A series of new semiconducting polymers with 2,2‐dimethyl‐2H‐benzimidazole, 9‐heptadecanyl‐9H‐carbazole, and thiophene (or bithiophene) units was synthesized using Stille polymerization to generate PCDTMBIs (or PCBBTMBIs). In dimethyl‐2H‐benzimidazole, the sulfur at 2‐position of BT unit was replaced with dialkyl substituted carbon, while keeping the 1,2‐quinoid form, to improve the solubility of the polymers. The absorption spectra of PCDTMBIs with thiophene units exhibit two maximum peaks at about 430 and 613–645 nm in solution. The solutions of PCBBTMBIs show two absorption peaks at about 445–456 and 630–645 nm which is red‐shifted about 20 nm when compared with PCDTMBIs caused by the introduction of bithiophene units. In most efficient polymer PCBBTMBI3, the device annealed at 100 °C for 10 min demonstrated a V_OC value of 0.60 V, a J_SC value of 4.31 mA/cm², and a FF of 0.35, leading to the power conversion efficiency (PCE) of 0.91%, under white light illumination (AM 1.5 G and 100 mW/cm²). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Diazaisoindigo bithiophene and terthiophene copolymers for application in field‐effect transistors and solar cells

Two donor–acceptor conjugated polymers with azaisoindigo as acceptor units and bithiophene and terthiophene as donor units have been synthesized by Stille polymerization. These two polymers have been successfully applied in field‐effect transistors and polymer solar cells. By changing the donor component of the conjugated polymer backbone from bithiophene to terthiophene, the density of thiophene in the backbone is increased, manifesting as a decrease in both ionization potential and in electron affinity. Therefore, the charge transport in field‐effect transistors switches from ambipolar to predominantly hole transport behavior. PAIIDTT exhibits hole mobility up to 0.40 cm²/Vs and electron mobility of 0.02 cm²/Vs, whereas PAIIDTTT exhibits hole mobility of 0.62 cm²/Vs. Polymer solar cells were fabricated based on these two polymers as donors with PC₆₁BM and PC₇₁BM as acceptor where PAIIDTT shows a modest efficiency of 2.57% with a very low energy loss of 0.55 eV, while PAIIDTTT shows a higher efficiency of 6.16% with a higher energy loss of 0.74 eV. Our results suggest that azaisoindgo is a useful building block for the development of efficient polymer solar cells with further improvement possibility by tuning the alternative units on the polymer backbone. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2691–2699     

Supramolecular complexes of poly(3‐Hexylthiophene)‐block (and random)‐poly[3‐(2‐(6‐carboxyhexyl)methyl)thiophene] copolymers with perylene bisimide

Block and random copolymers of poly(3‐hexylthiophene) and poly[3‐(2‐(6‐carboxyhexyl)methyl)thiophene] with side‐chain carboxylic functionality ((P3HT‐b‐P3COOH) and (P3HT‐r‐P3COOH) were developed by Grignard Metathesis (GRIM) polymerization. The carboxylic functionality was introduced in the side chain via the oxazoline route. Both the block and random polythiophene copolymers were complexed with pyridine functionalized perylene bisimide to obtain supramolecular block and random polymer complexes. The complex formation in both systems was confirmed by ¹H NMR, WXRD and SAXS studies. An expansion of d spacing upon complex formation was observed in both the block and random copolymer, which could be traced by WXRD. Hole and electron mobilities measured for the supramolecular complexes indicated values which were higher by an order of magnitude for the supramolecular block complex (μ_h ≈ 2.9 × 10⁻⁴ cm²/Vs; μ_e ≈ 3.1 × 10⁻⁶ cm²/Vs) as compared to the random (μ_h ≈ 1.4 × 10⁻⁵ cm²/Vs; μ_e ≈ 4.7 × 10⁻⁷ cm²/Vs) copolymer. These results are indicative of the higher degree of disorder prevailing in the films of random copolymer system compared to the block copolymer. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1574–1583     

High performance polymer field‐effect transistors based on polythiophene derivative with conjugated side chain

Poly(3‐[2‐(5‐hexyl‐2‐thienyl) ethenyl]‐2,2′‐bithiophene) ( P2 , see Scheme 1 ) with conjugated thienylvinyl side chain was synthesized by copolymerization of the thiophene units with and without conjugated side chain with Pd‐catalyzed Stille coupling method. For comparison, P1 with the hexyl side chain instead of conjugated side chain was also synthesized. P2 film shows broad absorption in the visible region with absorption edge at about 700 nm. The solution‐processed polymer field‐effect transistors were fabricated and characterized with bottom gate/top contact geometry. The organic field‐effect transistors (OFET) based on P2 showed an average hole mobility of about 0.034 cm²/Vs (the highest value reached 0.061 cm²/Vs) upon annealing at about 180 °C for 30 min, with a threshold voltage of ?1.15 V and an on/off ratio of 10⁴ with n‐octadecyltrichlorosilane (OTS) modified SiO₂ substrate. In comparison, the OFET based on P1 displayed a hole mobility of 8.9 × 10^–4 cm²/Vs and an on/off ratio of 10⁴ with OTS modified SiO₂ substrate. The results indicate that the polythiophene derivative with conjugated thienylvinyl side chain is a promising polymer for the application in polymer field‐effect transistors. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5304–5312, 2009     

Synthesis and characterization of low‐bandgap cyclopentadithiophene‐biselenophene copolymer and its use in field‐effect transistor and polymer solar cells

Novel series of conjugated copolymers, incorporating cyclopentadithiophene (CPDT) and the biselenophene ( R‐CPDT‐Se2 ), were synthesized by Pd‐catalyzed Stille coupling polymerization. The optical, electrochemical, field‐effect carrier mobilities, and photovoltaic properties of the R‐CPDT‐Se2 were investigated and compared with cyclopentadithiophene (CPDT) and the bithiophene ( EHex‐CPDT‐T2 ). The highest hole mobility of thin film transistor devices fabricated with new p‐type polymer semiconductors, Oct‐CPDT‐Se2 , was 1.3 × 10^?3 cm²/Vs with an on/off ratio of about 10⁵. The maximum power conversion efficiency of polymer solar cell fabricated with the blend of EHex‐CPDT‐Se2 /C₇₁‐PCBM reached 1.86% with an open circuit voltage (V_OC) of 0.55 V, a short circuit current density (J_sc) of 7.27 mA/cm², and a fill factor (FF) of 0.47 under AM 1.5G irradiation (100 mW/cm²). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Synthesis and photovoltaic properties of copolymers based on bithiophene and bithiazole

Three simple structured D‐A copolymers, PBTBTz‐1 , PBTBTz‐2 , and PBTBTz‐3 , containing bithiophene (BT) donor unit and bithiazole (BTz) acceptor unit with different alkyl chain length were synthesized by the Pd‐catalyzed Stille‐coupling method. The copolymers were characterized by thermogravimetric analysis, UV–vis absorption, electrochemical cyclic voltammetry, and photovoltaic measurements. The results indicate that the introduction of BTz unit to the polythiophene main chain effectively decreases highest occupied molecular orbital levels of the copolymers and increases the open circuit voltage (V_oc) of polymer solar cells (PSCs) based on the copolymers as donor, and the alkyl chain length influences the photovoltaic properties of the polymers significantly. The PSCs based on PBTBTz‐2 and PBTBTz‐3 show higher V_oc up to 0.77 and 0.81 V, respectively. The power conversion efficiency of the PSC based on PBTBTz‐2 :PC₇₀BM = 1:1(w/w) reached 2.58% with short circuit current of 8.70 mA/cm², under the illumination of AM1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Donor–acceptor‐structured naphtodithiophene‐based copolymers for organic thin‐film transistors

New donor–acceptor (D‐A) polymers, poly(4,5‐bis(2‐octyldodecyloxy)naphto[2,1‐b:3,4‐b']dithiophenebenzo[c][1,2,5]thiadiazole) (PNDT‐B) and poly(4,5‐bis(2‐octyldodecyloxy)naphto [2,1‐b:3,4‐b′]dithiophene‐4,7‐di(thiophen‐2‐yl)benzo[c][1,2,5]thiadiazole) (PNDT‐TBT), with the extended π‐electron delocalization of naphtho[2,1‐b:3,4‐b']dithiophene, were successfully synthesized by Suzuki and Stille coupling reactions. The structure and physical properties of polymers were characterized by DFT calculation, UV–vis absorption, cyclovoltammetry, TGA and DSC analyses. X‐ray diffraction studies indicated a relatively highly ordered intermolecular structure in PNDT‐TBT after annealing. This high degree of molecular order resulted from the crystallinity and increasing planarity, provided by the thiophene linker groups and the interdigitation of the long alkoxy side chains. The new D‐A polymer, PNDT‐TBT, exhibited a p‐type carrier mobility of 0.028 cm²/Vs and an on/off ratio of 5.9 × 10³. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 525–531     

Thermally curable organic/inorganic hybrid polymers as gate dielectrics for organic thin‐film transistors

New low‐temperature curable organic/inorganic hybrid polymers were designed and synthesized as gate dielectrics for organic thin‐film transistors (OTFTs). Allyl alcohols were introduced to polyhedral oligomeric silsesquioxane (POSS) via hydrosilyation to produce an alcohol‐functionalized POSS derivative (POSS‐OH). POSS‐OH was then reacted with hexamethoxymethylmelamine at carrying molar ratios at 80 °C in the presence of a catalytic amount of p‐toluenesulfonic acid to give highly cross‐linked network polymers (POSS‐MM). The prepared thin films were smooth and hard after the thermal cross‐linking reaction and had very low leakage currents (<10^?8 A/cm²) with no significant absorption over the visible spectral range. Pentacene‐based OTFTs using the synthesized insulators as gate dielectric layers had higher hole mobilities (up to 0.36 cm²/Vs) than a device using thermally cross‐linked poly(vinyl phenol) and melamine as the gate dielectric layer (0.18 cm²/Vs). © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3260–3268     

Novel alkoxyanthracene donor and benzothiadiazole acceptor for organic thin film transistor and bulk heterojunction organic photovoltaic cells

Novel alkoxy anthracene (ODA)‐based polymeric semiconductors were designed for polymer solar cell applications. Alkoxyanthracene, which contains many π electrons and electron donating group, was easily synthesized. The copolymers, poly(alkoxy anthracene‐alt‐thiophene benzothiadiazole thiophene) poly(ODA‐TBT) and poly(alkoxy anthracene‐alt‐benzothiadiazole) poly(ODA‐BT), have been obtained by Suzuki coupling polymerization. Both polymers have ODA unit as a donor and benzothiadiazole as an acceptor. ODA‐TBT has thiophene linkages between ODA and benzothiadiazole. The optical, thermal, and electrochemical properties have been investigated by UV–visible absorption, thermal gravimetric analysis, differential scanning calorimetry, and CV. Organic thin‐film transistor using polymers showed that the hole mobility of poly(ODA‐alt‐TBT) was around 3.6 × 10^?3 cm²/Vs with on/off ratio of 9.91 × 10⁵ while that of poly(ODA‐alt‐BT) was around 1.21 × 10^?2 cm²/Vs with on/off ratio of 2.64 × 10⁶. Organic photovoltaic performance based on polymers were evaluated with a configuration of ITO/PEDOT:PSS/active layer/LiF/Al. Poly(ODA‐TBT) exhibits a short circuit current (J_sc) of 3.9 mA/cm² and power conversion efficiency (PCE) of 1.4%, and poly(ODA‐BT) exhibits the J_sc of 6.4 mA/cm² and PCE of 2.2%. The better device performance of poly(ODA‐BT) is attributed to its charge transfer ability and enhanced mobility and crystallinity although poly(ODA‐BT) does not have extended π‐conjugation due to twisted structure compared with poly(ODA‐TBT). © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1306–1314     

High performance semiconducting polymers containing bis(bithiophenyl dithienothiophene)‐based repeating groups for organic thin film transistors

New dithienothiophene‐containing conjugated polymers, such as poly(2,6‐bis(2‐thiophenyl‐3‐dodecylthiophene‐2‐yl)dithieno[3,2‐b;2′,3′‐d]thiophene, 4 and poly(2,6‐bis (2‐thiophenyl‐4‐dodecylthiophene‐2‐yl)dithieno[3,2‐b;2′,3′‐d]thiophene, 8 have been successfully synthesized via Stille coupling reactions using dodecyl‐substituted thiophene‐based monomers, bistributyltin dithienothiophene, and bistributyltin bithiophene; these polymers have been fully characterized. The main difference between the two polymers is the substitution position of the dodecyl side chains in the repeating group. Grazing‐incidence X‐ray diffraction (GI‐XRD) gave clear evidence of edge‐on orientation of polycrystallites to the substrate. The semiconducting properties of the two polymers have been evaluated in organic thin film transistors (OTFTs). The two conjugated polymers 4 and 8 exhibit fairly high hole carrier mobilities as high as μ_ave = 0.05 cm²/Vs (I_ON/OFF = 3.42 × 10⁴) and μ_ave = 0.01 cm²/Vs, (I_ON/OFF = 1.3 × 10⁵), respectively, after thermal annealing process. The solvent annealed films underwent reorganization of the molecules to induce higher crystallinity. Well‐defined atomic force microscopy (AFM) topography supported a significant improvement in TFT device performance. The hole carrier mobilities of the solvent annealed films are comparable to those obtained for a thermally annealed sample, and were one‐order higher than those obtained with a pristine sample. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and properties of new fluorene‐based polyquinoxalines with an ether linkage in the main chain for light‐emitting diodes

A new series of fluorene‐based polyquinoxalines with an ether linkage in the main chain were prepared by the polycondensation reaction between a tetraketone monomer and 3,3′,4,4′‐tetraaminodiphenyl ether. The polycondensation was usually carried out in m‐cresol. The resulting polymers ( P1 – P3 ) [ P1 = poly(quinoxaline‐co‐9,9‐dihexyl‐2,7‐dimethyl‐9H‐fluorene) P2 = poly(quioxaline‐co‐9,9‐dihexyl‐9‐pentyl‐2,7‐di‐p‐tolyl‐9H‐fluorene) P3 = poly(quioxaline‐co‐9,9‐bis‐(4‐methoxy‐phenyl)‐2,7‐dimethyl‐9H‐fluorene)] showed good solubility in common organic solvents and high thermal stability with only a 5% weight loss up to 440 °C. P1 and P2 had very high glass‐transition temperatures of 212 and 223 °C, respectively, whereas P3 did not show any phase‐transition temperature in repeated scans up to 300 °C. All the polymers in photoluminescence showed blue emissions in the range of 432–465 nm, both in chloroform solutions and in thin films. Light‐emitting diode devices of the configuration indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer:poly(N‐vinylcarbazole) blend (2:8)/LiF/Al were fabricated with P1 or P2 and emitted blue light with electroluminescence peak wavelengths of 434 and 448 nm, respectively. The maximum brightness and the external quantum efficiency of P1 were 0.56 μW/cm² at 29 V and 0.056%, whereas P2 showed 0.50 μW/cm² at 34 V and a relatively low value of 0.015%, respectively. Cyclic voltammetry studies revealed that these polymers possessed low‐lying ionization potential energy levels ranging from ?5.49 to ?5.86 eV and low‐lying electron affinity energy levels ranging from ?2.65 to ?2.88 eV. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1189–1198, 2006     

Cationic copolymerization of indene with styrene derivatives: Synthesis of random copolymers of indene with high molecular weight

Random copolymers with high molecular weights of indene and p‐methylstyrene (pMeSt) were synthesized by cationic polymerization with trichloroacetic acid/tin tetrachloride in CH₂Cl₂ at low temperatures. When indene and pMeSt (1:1 v/v), for example, were polymerized at ?40 °C, both monomers were consumed at very similar rates to give a copolymer with high molecular weight [number‐average molecular weight (M_n): 8–9 × 10⁴]. This is indeed quite unexpected behavior for the combination of these two monomers because pMeSt polymerized over 1000 times faster than indene in the homopolymerization under the reaction conditions previously described. The product copolymer of indene and pMeSt had a random monomer sequence in it that was confirmed by NMR analyses and thermal‐property measurements. In sharp contrast with pMeSt, styrene and p‐chlorostyrene, which have no electron‐donating groups on the phenyl ring, led to low molecular weight polymers (M_n < 10,000) in the copolymerization with indene (1:1 v/v). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2449–2457, 2002     

Synthesis and characterization of low‐bandgap copolymers based on dihexyl‐2h‐benzimidazole and cyclopentadithiophene

A series of new semiconducting polymers based on 4,4‐dihexyl‐4H‐cyclopenta[2,1‐b:3,4‐b′]dithiophene, 2,2‐dihexyl‐2H‐benzimidazole, and thiophene units was synthesized. The polymers show good solubility at room temperature in organic solvents owing to long alkyl chain in new acceptor, 2,2‐dihexyl‐2H‐benzimidazole. The advantage of dihexyl‐2H‐benzimidazole compared to the benzothiadiazole is to improve the solubility of the polymer. It was found that these polymers can finely be tuned for photovoltaic application by adjusting the contents ratio of the dihexyl‐2H‐benzimidazole unit. The spectra of the solid films show absorption bands with maximum peaks in the range of 421–577 nm and the absorption onsets at 588–683 nm, corresponding to band gaps of 2.11–1.82 eV. The devices with PCPDTDTHBI‐1 :PC₇₁BM showed an open‐circuit voltage (V_OC) of 0.46 V, a short‐circuit current density (J_SC) of 3.83 mA/cm², and a fill factor of 0.36, giving a power conversion efficiency of 0.64%. Decrease of the dihexyl‐2H‐benzimidazole contents in the polymers induced red‐shift of the UV absorptions, and increased V_OC and J_SC values, to improve the efficiency of organic photovoltaics. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis,characterization, and field‐effect transistor performance of poly[2,6‐bis(3‐tridecanoxythiophen‐2‐yl)benzo[1,2‐b;4,5‐b′]dithiophene]

A new copolymer of benzo[1,2‐b:4,5‐b′]dithiophene and 3,3′‐bis(tridecanoxy)‐5,5′‐bithiophene was synthesized through Stille copolymerization. The bis‐(3‐alkoxythiophene) monomer was synthesized through a silver fluoride mediated, palladium‐catalyzed cross‐coupling, in which bromide functional groups were preserved instead of consumed. The copolymer has been characterized and applied in field‐effect transistors, giving a hole mobility of 2 × 10^?3 cm²/Vs and an on/off ratio >10⁶, with negligible hysteresis, on standard silicon substrates. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1973–1978, 2010     

Random propene/4‐methyl‐1‐pentene copolymers synthesized with C2 symmetric highly isospecific metallocenes

Propene (P)/4‐methyl‐1‐pentene (Y) copolymers in a wide range of composition were prepared with isospecific single center catalysts, rac‐Et(IndH₄)₂ZrCl₂ ( EBTHI ), rac‐Me₂Si(2‐Me‐BenzInd)₂ZrCl₂ ( MBI ), and rac‐CH₂(3‐^tBuInd)₂ZrCl₂ ( TBI ). ¹³C NMR analysis of copolymers and statistical elaboration of microstructural data at triad level were performed. Unprecedented and surprising results are here reported. Random P/Y copolymers were prepared with the most isospecific catalyst, TBI , that is known to prepare ethene/propene and ethene/4‐methyl‐1‐pentene copolymers with long homosequences of both comonomers, whereas longer homosequences of both comonomers were observed in copolymers from the less enantioselective metallocenes EBTHI and MBI . These findings, which are against what is acknowledged in the field, can pave the way for the preparation on a large scale of random propene‐based copolymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2575–2585     

Effects of substituted side‐chain position on donor–acceptor conjugated copolymers

The optical properties and electrical properties of a series of low‐band‐gap conjugated copolymers, in which alkyl side chains were substituted at various positions, were investigated using donor–acceptor conjugated copolymers consisting of a cyclopentadithiophene derivative and dithienyl‐benzothiadiazole. With substituted side chains, the intrinsic properties of the copolymers were significantly altered by perturbations of the intramolecular charge transfer. The absorption of poly[2, 6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3,4‐b′]dithiophene)‐alt‐4, 7‐bis(4‐octyl‐thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐ttOTBTOT ( P2 )], which assumed a tail–tail configuration, tended to blue shift relative to the absorption of poly[2,6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3,4‐b′]dithiophene)‐alt‐4,7‐bis (thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐TBTT ( P1 )]. The absorption of poly[2,6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3, 4‐b′]dithiophene)‐alt‐4,7‐bis(3‐octyl‐thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐hhOTBTOT ( P3 )], which assumed a head–head configuration, was blue shifted relative to that of P2 . The electrical transport properties of field‐effect transistors were sensitive to the side chain position. The field‐effect mobility in P2 (μ₂ = 1.8 × 10^?3 cm²/V s) was slightly lower than that in P1 (μ₁ = 4.9 × 10^?3 cm²/V s). However, the mobility of P3 was very low (μ₃ = 3.8 × 10^?6 cm²/V s). Photoexcitation spectroscopy showed that the charge generation efficiency (shown in transient absorption spectra) and polaron pair mobility in P1 and P2 were higher than in P3 , yielding P1 and P2 device performances that were better than the performance of devices based on P3 . © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and properties of triaryl diamine‐based hole‐transporting monomer and polymer

The synthesis and properties of hole‐transporting triaryl diamine‐based low‐molar‐mass compounds and polymer are reported. Comparative study on their thermal, optical, and photoelectrical properties is presented. All the synthesized compounds are found to form glasses with the glass transition temperatures in the range of 43–119 °C as characterized by differential scanning calorimetry. The ionization potentials of these compounds range from 5.31 to 5.40 eV as determined by electron photoemission method. Hole‐drift mobilities in the films of the synthesized compounds were estimated by the xerographic time‐of‐flight technique. They were found to reach 10^?3 cm²/Vs at electric field of 6.4 × 10⁵ V/cm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4674–4680, 2008     

Syntheses and characterization of carbazole based new low‐band gap copolymers containing highly soluble benzimidazole derivatives for solar cell application

Newly designed 2H‐benzimidazole derivatives which have solubility groups at 2‐position have been synthesized and incorporated into two highly soluble carbazole based alternating copolymers, poly[2,7‐(9‐(1′‐octylnonyl)‐9H‐carbazole)‐alt‐5,5‐(4′,7′‐di(thien‐2‐yl)‐2H‐benzimidazole‐2′‐spirocyclohexane)] (PCDTCHBI) and poly[2,7‐(9‐(1′‐octylnonyl)‐9H‐carbazole)‐alt‐5,5‐(4′,7′‐di(thien‐2‐yl)‐2H‐benzimidazole‐2′‐spiro‐4′′‐((2′′′‐ethylhexyl)oxy)‐cyclohexane)] (PCDTEHOCHBI) for photovoltaic application. These alternating copolymers show low‐band gap properties caused by internal charge transfer from an electron‐rich unit to an electron‐deficient moiety. HOMO and LUMO levels are –5.53 and –3.86 eV for PCDTCHBI, and –5.49 and –3.84 eV for PCDTEHOCHBI, respectively. Optical band gaps of PCDTCHBI and PCDTEHOCHBI are 1.67 and 1.65 eV, respectively. The new carbazole based the 2H‐benzimidazole polymers show 0.11–0.13 eV lower values of band gaps as compared to that of carbazole based benzothiadiazole polymer, poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT), while keeping nearly the same deep HOMO levels. The power conversion efficiencies of PCDTCHBI and PCDTEHOCHBI blended with [6,6]phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) are 1.03 and 1.15%, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Efficient gel‐type electrolyte with bismaleimide via in situ low temperature polymerization in dye‐sensitized solar cells

This study reports the characteristics of gel‐type dye‐sensitized solar cells (DSSCs), fabricated with gel‐type electrolyte containing poly‐1,1′‐(methylenedi‐4,1‐phenylene)bismaleimide (PBMI), or poly‐1,1′‐(3,3′‐dimethyl‐1,1′‐biphenyl‐4,4′‐diyl)bismaleimide (PDBBMI), or poly‐N,N′‐(4‐methyl‐1,3‐phenylene)bismaleimide (PMPBMI), prepared by in situ polymerization of the corresponding monomer without an initiator at 30 °C. Incorporating 0.3 wt % content of exfoliated alkyl‐modified nanomica (EAMNM) into PBMI‐gelled electrolyte leads to higher short‐circuit current density (J_sc = 17.14 mA cm^?2) and efficiency (η = 7.02%) than that of neat PBMI‐gel electrolyte (J_sc = 15.32 mA cm^?2, η = 6.41%). Incorporating 0.3 wt % EAMNM into PBMI‐gelled electrolyte results in remarkably stable device performance under continuous light soaking under one sun (100 mW cm^?2) at 55 °C. The efficiency of DSSCs based on PBMI/0.3 wt % EAMNM‐gelled electrolyte drops by only 1.7% (η = 6.93%) after 500 h of continuous light soaking. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene): Synthesis,optical and photovoltaic properties

A new benzodithiophene (BDT)‐based polymer, poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene) (PBDTV), was synthesized by Pd‐catalyzed Stille‐coupling method. The polymer is soluble in common organic solvents and possesses high thermal stability. PBDTV film shows a broad absorption band covering from 350 nm to 618 nm, strong photoluminescence peaked at 545 nm and high hole mobility of 4.84 × 10^?3 cm²/Vs. Photovoltaic properties of PBDTV were studied by fabricating the polymer solar cells based on PBDTV as donor and PC₇₀BM as acceptor. With the weight ratio of PBDTV: PC₇₀BM of 1:4 and the active layer thickness of 65 nm, the power conversion efficiency of the device reached 2.63% with V_oc = 0.71 V, I_sc = 6.46 mA/cm², and FF = 0.57 under the illumination of AM1.5, 100 mW/cm². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1822–1829, 2010