Au/TiO2 nanorod‐based Schottky‐type UV photodetectors

TiO₂ nanorods (NRs) were synthesized on fluorine‐doped tin oxide (FTO) pre‐coated glass substrates using hydrothermal growth technique. Scanning electron microscopy studies have revealed the formation of vertically‐aligned TiO₂ NRs with length of ～2 µm and diameter of 110–128 nm, homogenously distributed over the substrate surface. 130 nm thick Au contacts using thermal evaporation were deposited on the n‐type TiO₂ NRs at room temperature for the fabrication of NR‐based Schottky‐type UV photodetectors. The fabricated Schottky devices functioned as highly sensitive UV photodetectors with a peak responsivity of 134.8 A/W (λ = 350 nm) measured under 3 V reverse bias. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Unusual photoelectric behaviors of Mo-doped TiO2 multilayer thin films prepared by RF magnetron co-sputtering: effect of barrier tunneling on internal charge transfer

Mo-doped TiO₂ multilayer thin films were prepared by RF magnetron co-sputtering. Microstructures, crystallite parameters and the absorption band were investigated with atomic force microscopy, X-ray diffraction and ultraviolet-visible spectroscopy. Internal carrier transport characteristics and the photoelectric property of different layer-assemble modes were examined on an electrochemical workstation under visible light. The result indicates that the double-layer structure with an undoped surface layer demonstrated a red-shifted absorption edge and a much stronger photocurrent compared to the uniformly doped sample, signifying that the electric field implanted at the interface between particles in different layers accelerated internal charge transfer effectively. However, a heavily doped layer implanted at the bottom of the three-layer film merely brought about negative effects on the photoelectric property, mainly because of the Schottky junction existing above the substrate. Nevertheless, this obstacle was successfully eliminated by raising the Mo concentration to 10²⁰ cm^?3, where the thickness of the depletion layer fell into the order of angstroms and the tunneling coefficient manifested a dramatic increase. Under this circumstance, the Schottky junction disappeared and the strongest photocurrent was observed in the three-layer film.     

Electrical characteristics of p-Si/TiO2/Al and p-Si/TiO2-Zr/Al Schottky devices

Electrical devices involve different types of diode in prospective electronics is of great importance. In this study, p-type Si surface was covered with thin film of TiO₂ dispersion in H₂O to construct p-Si/TiO₂/Al Schottky barrier diode (D1) and the other one with TiO₂ dispersion doped with zirconium to construct p-Si/TiO₂-Zr/Al diode (D2) by drop-casting method in the same conditions. Electrical properties of as-prepared diodes and effect of zirconium as a dopant were investigated. Current–voltage (I–V) characteristics of these devices were measured at ambient conditions. Some parameters including ideality factor (n), barrier height (Φ_B0), series resistance (Rs) and interface state density (Nss) were calculated from I–V behaviours of diodes. Structural comparisons were based on SEM and EDX measurements. Experimental results indicated that electrical parameters of p-Si/TiO₂/Al Schottky device were influenced by the zirconium dopant in TiO₂.     

Hybrid ultraviolet photodetectors with high photosensitivity based on TiO2 nanorods array and polyfluorene

The highly oriented array composed of rutile TiO₂ nanorods is synthesized by the hydrothermal method on the SnO:F (FTO) substrate. The hybrid UV detector is fabricated via spin-coating a thin layer of poly (9,9-dihexylfluorene) (PFH) on the array. The device characteristics, including I-V curves under UV illumination and time response are studied. Obvious UV photoconductive effect is observed in the device and the response is fast to the switching on and off UV light illumination, which can be repeated for at least 50 times. The quick enhancement of the current origins from the large contact area between TiO₂ nanorods and PFH and the convenient charge transport in TiO₂ nanorods.     

Sulfonated poly(phenylene oxide)/Ti<Superscript>3+</Superscript>/TiO<Subscript>2</Subscript> nanotube arrays membrane/electrode with high performances for lithium ion battery

Sulfonated poly(phenylene oxide) (SPPO) film was electrodeposited on Ti³⁺-doped TiO₂ nanotube arrays (Ti³⁺/TiO₂NT) electrode via the electropolymerization of sulfonated phenol. The as-synthesized SPPO/Ti³⁺/TiO₂NT membrane/electrode was investigated in terms of SEM, FESEM, EDX, FTIR, XPS, galvanostatic charge/discharge, and cycle voltammetry (CV). As expected, the porous SPPO film did form on the surface of Ti³⁺/TiO₂NT electrode; furthermore, the resultant SPPO/Ti³⁺/TiO₂NT membrane/electrode delivered higher electrochemical performances than PPO/Ti³⁺/TiO₂NT, mainly attributed to the contributions of the ionic conductivity induced by –SO₃H groups within SPPO.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

Synergetic Photocatalytic Nanostructures Based on Au/TiO2/Reduced Graphene Oxide for Efficient Degradation of Organic Pollutants

Recently, there is crucial interest in the design and fabrication of nanocatalysts for efficient decomposition of organic pollutants in wastewater using visible light. This work reports the assembling fabrication of synergetic photocatalytic Au/TiO₂/RGO nanostructures by utilizing the reduced graphene oxide (RGO) as substrate material and efficient separator for electrons and holes. The Au/TiO₂ nanostructures with a ≈7 nm TiO₂ particles size are dispersed uniformly on RGO nanosheets. UV–vis diffuse reflectance spectroscopy verifies that Au/TiO₂/RGO nanocomposites show strong absorption of visible light. The degradation efficiency after 1 h for hydroquinone under visible light and UV light is ≈77% and ≈90%, respectively. Under visible light, the calculated apparent rates (k ) of the Au/TiO₂/RGO nanocomposites are 0.0112 and 0.0174 min^?1 for decomposition of methylene blue and hydroquinone. That are five times greater than that of bare TiO₂. The high photocatalytic activity is mainly attributed to the synergy between RGO and Au/TiO₂ nanostructure. The strategy of composite nanostructures assembling on RGO is ensured to have a great practicable potential for the designing of high efficient multielement composite nanoparticles catalysts.     

Self‐formed Schottky barrier induced selector‐less RRAM for cross‐point memory applications

We propose a selector‐less Pr_0.7Ca_0.3MnO₃ (PCMO) based resistive‐switching RAM (RRAM) for high‐density cross‐point memory array applications. First, we investigate the inhomogeneous barrier with an effective barrier height (Φ_eff), i.e., self‐formed Schottky barrier. In addition, a scalable 4F² selector‐less cross‐point 1 kb RRAM array has been successfully fabricated, demonstrating set, reset, and read operation for high cell efficiency and high‐density memory applications. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Photo(electro)catalytic Activity of Cu-Modified TiO2 Nanorod Array Thin Films under Visible Light Irradiation

In the present study, a two-step method was applied to synthesise Cu²⁺-modified TiO₂ nanorod array thin films for photocatalytic processes. TiO₂ nanorod array thin films were synthesised by a hydrothermal method and then modified with an ultrasonic-assisted sequential cation adsorption method. The samples were characterised by X-ray diffraction (XRD), UV–vis diffuse reflectance spectra (DRS), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy and inductively coupled plasma mass spectroscopy (ICP-MS) analysis. The photoelectrochemical properties of the samples were evaluated by linear sweep voltammetry and Mott–Schottky analysis; photocatalytic activities were tested by methylene blue degradation under visible light. The photocurrent density of the TiO₂/FTO sample modified with 50 mM Cu²⁺ solution was 26 times higher than that of the unmodified TiO₂/FTO sample. Additionally, methylene blue degradation efficiency under visible light was increased 40% with respect to the efficiency of the unmodified sample. The mechanism of the photocatalytic activity enhancement of Cu²⁺-modified TiO₂ nanorod films was discussed.     

ZnO nanowire array ultraviolet photodetectors with self-powered properties

A ZnO nanowire (NW) array ultraviolet photodetector (PD) with Pt Schottky contacts has been fabricated on a glass substrate. Under UV light illumination, this PD showed a high photo-to-dark current ratio of 892 at 30 V bias. Interestingly, it was also found that this PD had a high sensitivity of 475 without external bias. This phenomenon could be explained by the asymmetric Schottky barrier height (SBH) at the two ends causing different separation efficiency of photogenerated electron–hole pairs, which resulted in the formation of photocurrent. It is anticipated to have potential applications in self-powered UV detection field.     

Investigation into the effects of deposition parameters on TiO2 photocatalyst thin films by rf magnetron sputtering

Titanium dioxide (TiO₂) photocatalyst thin films were deposited on non-alkali glass substrates by radio frequency (rf) magnetron sputtering. The Taguchi method with orthogonal array, signal-to-noise ratio and analysis of variance were employed to study the performance characteristics. The experimental studies were conducted under different rf powers, sputtering pressures, O₂/(Ar+O₂) flow-rate ratios, and substrate temperatures. The deposited TiO₂ films were of the anatase phase with a (101) preferred orientation. We performed both photoinduced decomposition of methylene blue (MB) and photoinduced hydrophilicity under UV light illumination. With the optimized TiO₂ photocatalyst thin film deposition conditions, the water contact angle after 9 min UV illumination was approximately 5, the absorbance of MB was reduced to 0.2 for 240 min UV irradiation, and the deposition rate was 34.18 Å/min.     

TiO<Subscript>2</Subscript> Nanorod Arrays Sensitized with CdS Quantum Dots for Solar Cell Applications: Effects of Rod Geometry on Photoelectrochemical Performance

CdS quantum dot (QD) sensitized TiO₂ nanorod array (NRA) film electrodes with different rod geometries were fabricated via a solvothermal route followed by a sequentialchemical bath deposition (S-CBD) process. By controlling the solution growth conditions, the rod geometries, especially the tip structures, of the TiO₂ NRAs were tuned. The results indicated that the vertically aligned hierarchical NRAs possessed conically shaped tip geometry, which was favorable for film electrodes due to the reduced reflectance, enhanced light harvesting, fast charge-carrier separation and transfer, suppression of carrier recombination, sufficient electrolyte penetration and subsequent efficient QD assembly. CdS QD sensitized TiO₂ NRA film electrodes with tapered tips exhibited an enhanced photoelectrochemical (PEC) performance, a photocurrent intensity of 5.13 mA/cm² at a potential of 0 V vs. saturated calomel electrode, an open-circuit potential of −0.68 V vs. saturated calomel electrode and an incident photon to current conversion efficiency (IPCE) of 22% in the visible-light region from 400 to 500 nm. The effects of rod geometry on the optical absorption, reflectance, hydrophilic properties and PEC performance of bare TiO₂ and CdS QD sensitized TiO₂ NRA film electrodes were investigated. The mechanism of charge-carrier generation and transfer in these CdS QD sensitized solar cells based on vertically aligned TiO₂ nanorods is discussed.     

Fabrication of p-ZnO:ZrN thin films by RF magnetron sputtering

An attempt has been made to fabricate p-ZnO thin films from the ZrN mixed ZnO targets by RF magnetron sputtering. The targets of different ZrN concentrations (0, 1, 2, and 4?mol%) have been prepared by solid-state reaction route. The ZrN-codoped ZnO films grown on semi-insulating Si (100) substrates have been characterized by X-ray diffraction (XRD), photoluminescence (PL), Hall effect measurement, time-of-flight secondary ion mass spectrometer (ToF-SIMS), and atomic force microscopy (AFM). XRD studies reveal that all films are oriented along (002) plane. The Hall measurements showed p-conductivity for 1 and 2?mol% ZrN-codoped ZnO films. Further, it has been found that 1?mol% ZrN-codoped film has low resistivity (7.5?×?10^?2?Ω?cm) and considerable hole concentration (8.2?×?10¹⁸?cm^?3) by optimum incorporation of nitrogen due to best codoping. The red shift in near-band-edge emission observed from PL well acknowledged the p-conduction in 1 and 2?mol% ZrN-codoped ZnO film. The incorporation of N and Zr atoms in the ZnO matrix has been confirmed by ToF-SIMS analysis. The increase in peak to valley roughness (R _pv) with increase of doping concentration has been observed from AFM analysis. ZnO homojunction has also been fabricated with the best codoped p-ZnO film and it showed typical rectification behavior of a diode. The junction parameters have also been determined for the fabricated homojunction.     

Characterization and antibacterial functions of Ag–TiO<Subscript>2</Subscript> and W–TiO<Subscript>2</Subscript> nanostructured thin films prepared by sol-gel/laser-induced technique

A novel sol-gel/laser-induced technique (SGLIT) has been developed to form nanocrystalline titanium dioxide (TiO₂) based thin films with an improved antibacterial performance. TiO₂ precursor films loaded with W⁺⁶ and Ag⁺² ions (W–TiO₂, Ag–TiO₂) were prepared separately by sol-gel method and spin-coated on microscopic glass slides. As-dried films were subjected to KrF excimer laser pulses at optimized parameters to generate mesoporous anatase and rutile phases at room temperature. The anatase phase was obtained after irradiation with 10 laser pulses only at 75–85 mJ/cm² fluence in W–TiO₂ films. However, higher number of laser pulses and higher W⁺⁶ content favored the formation of rutile. Whereas Ag–TiO₂ films exhibited anatase up to 200 laser pulses at the same fluence. The films were characterized by using XRD, FEG-SEM, TEM and UV-Vis spectrophotometer to investigate the crystallographic structure, phase transformation, surface morphology, film thickness and the optical properties. A crystallite size of approximately 20 nm was achieved from the anatase prepared by SGLIT. The films exhibited an enhanced antibacterial function against E-Coli cells under the UV excitation.     

高Tc超导薄膜约瑟夫逊结光探测研究

我们研制了具有约瑟夫逊效应的高Tc GdBa₂Cu₃O₇-薄膜双晶晶界结,对其交直流约瑟夫逊效应进行了观测,并用其进行光探测,用波长为0.6328μm的He-Ne激光器辐照双晶结结区,系统观测了双晶晶界结的光响应特性,得到的最好结果如下噪音等效功率NEP=1.9×10^-13W,归一化探测率D=53×109cmHz^1/2W^-1,响应率Rv=4.2×10⁷V/W,响应时间τ=4.35×10^-7s.     

Contact potential barriers and characterization of Ag-doped composite TiO2 nanotubes

Ag-doping TiO₂ composite nanotubes (Ag-TNTs) were synthesized by alkaline fusion followed by hydrothermal treatment. The microstructure and morphology of the materials were characterized by XRD, TEM, XPS, SPS (surface photovoltage spectroscopy), FISPS (electric field-induced surface photovoltage spectroscopy) and Raman spectroscopy. First-principles calculations based on density-functional theory (DFT) showed the formation of several impurity levels near the top of the valence band in the band gap (E_g) of rutile TiO₂ due to Ag doping. A “double junction” is proposed, involving a Schottky junction and p–n junction (denoted as “Ag-p–n junction”) occurring between the Ag particles and the nanotube surface, as well as forming inside TiO₂ nanotubes, respectively. The strongly built-in electric field of the junctions promotes the separation of photo-holes and photoelectrons, enhancing the photocatalytic efficiency. XRD results indicated that the composite Ag-TNTs exist as a mixture of anatase and rutile phases. XPS results showed that Ti⁴⁺ is the primary state of Ti. Raman spectral analysis of Ag-TNTs revealed the presence of a new peak at 271 cm⁻¹. The red-shift of the absorption light wavelength of Ag-TNTs was 0.16 eV (20 nm) due to a considerable narrowing of E_g by the existing impurity levels.     

Synthesis of Ag metallic nanoparticles by 120 keV Ag− ion implantation in TiO2 matrix

TiO₂ thin film synthesized by the RF sputtering method has been implanted by 120 keV Ag^? ion with different doses (3?×?10¹⁴, 1?×?10¹⁵, 3?×?10¹⁵, 1?×?10¹⁶ and 3?×?10¹⁶ ions/cm²). Further, these were characterized by Rutherford back Scattering, XRD, X-ray photoelectron spectroscopy (XPS), UV–visible and fluorescence spectroscopy. Here we reported that after implantation, localized surface Plasmon resonance has been observed for the fluence 3?×?10¹⁶ ions/cm², which was due to the formation of silver nanoparticles. Ag is in metallic form in the matrix of TiO₂, which is very interestingly as oxidation of Ag was reported after implantation. Also, we have observed the interaction between nanoparticles of Ag and TiO₂, which results in an increasing intensity in lower charge states (Ti³⁺) of Ti. This interaction is supported by XPS and fluorescence spectroscopy, which can help improve photo catalysis and antibacterial properties.     

Improved charge collection efficiency of hollow sphere/nanoparticle composite TiO2 electrodes for solid state dye sensitized solar cells

The photoanodes of solid state dye sensitized solar cells (ss-DSCs) embedded with different contents of TiO₂ hollow spheres (HSs) were prepared and the photovoltaic performances were systematically characterized. TiO₂ hollow spheres were synthesized by a facile sacrificial templating method, grounded and added in different ratios to TiO₂ nanoparticle (NP) paste, from which composite HS/NP electrodes were fabricated. The composite photoanodes include hollow spheres of 300–700 nm with enhanced light scattering characteristics in visible range which leads to improved light absorption in conventional thin film electrodes of ss-DSC. By optimizing the amount of HSs in the paste, 40% improvement in efficiency was obtained in comparison to ss-DSC utilized pure NP electrodes. By increasing the fraction of HSs in the electrode the current density increased by 56% (from 2.5 to 3.9 mA cm^?2). The improved photovoltaic performance of ss-DSC is primarily due to different morphology and altered charged trap distribution in HSs in comparison to NP which leads to significant enhancement in electron transport time and electron lifetime as well as charge collection efficiency and light absorption properties.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

High‐temperature stability of Au/p‐type diamond Schottky diode

Rectification properties of Au Schottky diodes were investigated in high‐temperature operation. These diodes were fabricated on a p‐type diamond single crystal using the vacuum‐ultraviolet light/ozone treatment. The ideality factor n of the Schottky diodes decreased monotonically with increasing measurement temperature whereas the Schottky barrier height ?_b increased, and ?_b reached 2.6 eV at 550 K with n of 1.1. Through high temperature heating at 870 K, the mean value of ?_b at 300 K changed permanently from 2.2 eV to 1.1 eV. Decrease of ?_b might originate from a dissolution of oxygen termination at the Au/diamond interface. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)