Influence of nitroxide structure on polystyrene brushes “grafted‐from” silicon wafers

Alkoxyamine derivatives based on 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO), N‐tert‐butyl‐N‐(1‐diethylphosphono‐(2,2‐dimethylpropyl)) nitroxide (SG1) and N‐tert‐butyl‐N‐(2‐methyl‐1‐phenylpropyl) nitroxide (TIPNO) containing a C₁₁ hydrophobic spacer and a reactive triethoxysilyl polar head, were synthesized and anchored to silicon wafers by the Langmuir–Blodgett reactive deposition technique at surface pressures ranging from 15 to 32 mN/m. Polystyrene brushes (M_n ～ 8500–66,400 g/mol) were grown from the alkoxyamine functionalized silicon wafers by nitroxide mediated radical polymerization and characterized by ellipsometry and water contact angle measurements. The main parameters influencing the grafting density and the degree of stretching of the brushes are the nitroxide polarity and, therefore, the behavior of the corresponding alkoxyamines at the air/water interface of the Langmuir–Blodgett trough. Depending on the alkoxyamine chemical structure and the surface pressure during Langmuir–Blodgett deposition, polystyrene brushes with grafting densities of 0.3–1.0 chains/nm² and stretching values of 40–70% were obtained. Regarding alkoxyamines deposited at high surface pressures, size exclusion chromatography experiments performed on both cleaved polystyrene brushes and chains simultaneously grown in the bulk revealed that the polymerization degree of the bulk and surface chains are significantly different, suggesting that steric constrains affect the polymerization kinetics occurring at the silicon surface. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3367–3374, 2008     

“Close loop” mechanistic schemes for hydrocarbon polymer oxidation

Mechanistic schemes of radical oxidation of hydrocarbon polymers in which initiation is only due to unimolecular or bimolecular hydroperoxide decomposition have been studied. The results of their kinetic analysis have been compared with literature data relative to the thermal oxidation of polypropylene in solid state (60-160°C). These data are in remarkably good agreement with the “unimolecular” scheme whose main characteristics are: (1) the quasi-independence of the kinetic behavior with initial conditions (for low initial content of thermolabile structures), and (2) the fact that an arbitrarily defined induction period depends only on the rate constant of unimolecular hydroperoxide decomposition. © 1995 John Wiley & Sons, Inc.     

Flexible triboelectric generator and pressure sensor based on poly[(R)‐3‐hydroxybutyric acid] biopolymer

The utilization of poly[(R)‐3‐hydroxybutyric acid] (PHB) biopolymer for a device that uses charging process in friction to convert mechanical energy into electric power is reported. The triboelectric generator (TEG) is fabricated by stacking a drop cast PHB film between indium tin oxide coated poly(ethylene terephthalate) (PET) and PET sheet. The charge transfer takes place through an established general rule according to which the material with higher dielectric constant becomes positively charged. Furthermore, the utilization of such TEG as pressure sensor is illustrated. TEGs have the potential of harvesting energy from touch screen, mechanical vibration, and more, with great applications in self‐powered sensors for heat and environmental monitoring and even large‐scale applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 859–863     

Renewable benzoxazine monomers from “lignin‐like” naturally occurring phenolic derivatives

The benzoxazines of three naturally occurring phenylpropanoid phenols: ferulic, coumaric, and phloretic acids, and their esters are described. Benzoxazines with conjugated unsaturated chains exhibit unusual poor thermal stability and degrade partially at the polymerization temperature making necessary the use of a catalyst (BF₃.Et₂O) to low the polymerization temperature and prevent degradation. Polybenzoxazines are prepared thermally and characterized by DSC and TGA techniques. The resulting materials have superior Tgs when compared with those prepared from an unsubstituted monofuctional benzoxazine due to the additional crosslinking through the ester and carboxylic moieties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4894–4903     

Thermally amendable tailor‐made functional polymer by RAFT polymerization and “click reaction”

This investigation reports the preparation and characterization of thermally amendable functional polymer bearing furfuryl functionality via reversible‐addition fragmentation and chain transfer (RAFT) polymerization and Diels‐Alder (DA) reaction. In this case, furfuryl methacrylate (FMA) was polymerized using 4‐cyano‐4‐[(dodecylsulfanylthiocarbonyl)sulfanyl] pentanoic acid as RAFT reagent and 4,4′‐azobis(4‐cyanovaleric acid) as thermal initiator. ¹H NMR, ¹³C NMR, and matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry analysis showed that furfuryl group in poly(furfuryl methacrylate) (PFMA) was not affected during RAFT polymerization and the tailor‐made polymer had RAFT end group. The DA reaction was successfully carried out between the reactive furfuryl functionality of PFMA and different bismaleimides. The thermoreversible property of these DA polymers was characterized by FT‐IR and DSC analysis. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3365–3374     

Synthesis of thermosetting polyetherimide‐containing allyl groups

An allyl‐containing diphenol, 1‐(3‐allyl‐4‐hydroxyphenyl)‐1‐(4‐hydoxyphenyl)‐1‐(6‐oxido‐6H ‐dibenz[c,e][1,2]oxaphosphorin‐6‐yl)ethane (1) , was prepared from a one‐pot reaction of 9,10‐dihydro‐oxa‐10‐phosphaphenanthrene‐10‐oxide, 4‐hydroxyacetophenone, and 2‐allylphenol in the presence of p‐toluenesulfonic acid monohydrate. Then, an allyl‐containing dietheramine, 1‐(4‐(4‐aminophenoxy)phenyl)‐1‐(3‐allyl 4‐(4‐aminophenoxy)‐phenyl)‐1‐(6‐oxido‐6H‐dibenz[c,e][1,2] oxaphosphorin‐6‐yl)ethane (3) , was prepared from the nucleophilic substitution of (1) with 4‐fluoronitrobenzene, followed by the reduction of the dinitro groups by Fe/HCl. A flexible polyetherimide (PEI) (4) with a curable characteristic was prepared from the condensation of (3) and 4,4′‐oxydiphthalic anhydride (ODPA) in m‐cresol in the presence of isoquinoline. Curing PEI (4) at 300 °C leads to PEI (5) , which exhibits much a higher T_g value (307 °C) and a lower coefficient of thermal expansion (CTE) (29 ppm/°C) than PEI (4) (T_g = 253 °C, CTE 52 ppm/°C). © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

High density cationic polymer brushes from combined “click chemistry” and RAFT‐mediated polymerization

A simple method for preparing cationic poly[(ar‐vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was used by combined technology of “click chemistry” and reversible addition‐fragmentation chain transfer (RAFT) polymerization. Initially, silicon surfaces were modified with RAFT chain transfer agent by using a click reaction involving an azide‐modified silicon wafer and alkyne‐terminated 4‐cyanopentanoic acid dithiobenzoate (CPAD). A series of poly(VBTAC) brushes on silicon surface with different molecular weights, thicknesses, and grafting densities were then synthesized by RAFT‐mediated polymerization from the surface immobilized CPAD. The immobilization of CPAD on the silicon wafer and the subsequent polymer formation were characterized by X‐ray photoelectron spectroscopy, water contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and ellipsometry analysis. The addition of free CPAD was required for the formation of well‐defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. In addition, by varying the polymerization time, we were able to obtain poly(VBTAC) brushes with grafting density up to 0.78 chains/nm² with homogeneous distributions of apparent needle‐like structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A facile “graft from” method to prepare molecular‐level dispersed graphene–polymer composites

Graphene–polymer composites of positive‐charged poly(dimethyl aminoethyl acrylate), negative‐charged poly(acrylic acid), and neutral polystyrene were prepared by “graft from” methodology using reversible addition fragmentation chain transfer (RAFT) polymerization via a pyrene functional RAFT agent (PFRA) modified graphene precursor. Fluorescence spectroscopy and attenuated total reflection infrared (ATR‐IR) evidenced that the PFRA was attached on the graphene basal planes by π–π stacking interactions, which is strong enough to anti‐dissociation in the polymerization mixture up to 80°C. Atomic force microscopy (AFM) revealed that the thickness of a graphene–polymer sheet was about 4.0 nm. Graphene composites of different polymers with the same polymerization degree exhibited similar conductivity; however, when the polymer chain was designed as random copolymer the conductivity was significantly decreased. It was also observed that the longer the grafted polymer chains the lower the conductivity. ATR‐IR spectroscopy and thermogravimetric analysis were also performed to characterize the as‐prepared composites. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Examples of “intrinsically” and “extrinsically” determined phase morphologies in polymer alloys

The properties of polymer alloys are strongly dependent on their phase morphologies. Usually, the phase dispersion and domain sizes are affected by the process and can be influenced and stabilized only “extrinsically” by dispersants and emulsifiers. But, there are some examples of alloys with phase morphologies which are “intrinsically” determined and thus independently of the processing conditions. This aspect of phase determining factors is discussed using four principally different examples of polymer alloys.     

Functional film of ethylene vinyl acetate and co‐polyamide compound containing “Nisin” active substance

This study deals with flexible films incorporating nisin for antibacterial active packaging purposes. A novel approach was used to gain control over nisin release profile from a thermoplastic film in order to enhance its antibacterial efficiency. This approach involves polymer blends of ethylene vinyl acetate copolymer and co‐polyamide at various ratios. It was shown that the release profile of an antibacterial substance from active packaging to foodstuff is a key factor concerning the antibacterial efficiency. Samples of 400[μm] were produced by using a laboratory twin screw compounder and a laboratory hot press. Samples were characterized for their migration kinetics, molecular interactions, mechanical properties, and water swelling properties. Antibacterial activity tests show that nisin incorporated films reduced bacterial count by different extents. Listeria ATCC 33090 was used as target bacteria (data not shown). Nisin migration profile to water medium was determined by Lowry's protocol. Scanning electron microscopy images and thermal analysis indicated that no significant molecular interactions occurred. Furthermore, droplet and co‐continues like morphology were seen at different polymer blend ratios. Osmotic pressure driven release mechanism appears to be the dominant migration mechanism, and diffusion kinetics was dominant. Results show that morphology of the polymer blend matrix alters the diffusion coefficient. In addition, water swelling characterization of different samples was done in order to reveal the relations with the diffusion coefficient. It seems that there is an inverse resemblance between water swelling and the diffusion coefficient trends.     

“Dumbbell”‐ and “Clackers”‐Shaped Dimeric Derivatives of Monocarba‐closo‐dodecaborate

We designed, synthesized, and characterized two types of dimeric forms of monocarba‐closo‐dodecaborate, namely, a “dumbbell”‐shaped dianion having a C?C bond and a “clackers”‐shaped monoanion having an iodonium linker. The unique architectures of these anionic molecules were established by X‐ray analysis. Spectroscopic analysis, DFT calculations, and reactivity experiments revealed high anionic and chemical stability of both anions, which are crucial properties for weakly coordinating anions.     

Investigating the chain conformations of spin‐coated polymer thin films by ToF‐SIMS depth profiling

Thin films of bromine‐terminated poly(bisphenol A octane ether) (BA‐C10) were prepared using 1,2‐dichlorobenzene (ODCB) as the solvent. The organization of the chains in these amorphous polymer films was evaluated using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) depth profiling. For the thin films, the bifunctional polymer chains were folded and anchored to the substrate via their two Br end groups and a polymer brush of chain loops was formed on the substrate. As the film thickness increased, polymer chains in a random coil conformation were found to reside on the top of the polymer brush. Depth profiling revealed that the polymer chains were densely packed at the interface. Moreover, the polymer films showed thermal stability, implying strong interactions between the end groups and the substrate. Copyright © 2015 John Wiley & Sons, Ltd.     

Topological “interfacial” polymer chemistry: Dependency of polymer “shape” on surface morphology and stability of layer structures when heating organized molecular films of cyclic and linear block copolymers of n‐butyl acrylate‐ethylene oxide

The “topological polymer chemistry” of amphiphilic linear and cyclic block copolymers at an air/water interface was investigated. A cyclic copolymer and two linear copolymers (AB‐type diblock and ABA‐type triblock copolymers) synthesized from the same monomers were used in this study. Relatively stable monolayers of these three copolymers were observed to form at an air/water interface. Similar condensed‐phase temperature‐dependent behaviors were observed in surface pressure–area isotherms for these three monolayers. Molecular orientations at the air/water interface for the two linear block copolymers were similar to that of the cyclic block copolymer. Atomic force microscopic observations of transferred films for the three polymer types revealed the formation of monolayers with very similar morphologies at the mesoscopic scale at room temperature and constant compression speed. ABA‐type triblock linear copolymers adopted a fiber‐like surface morphology via two‐dimensional crystallization at low compression speeds. In contrast, the cyclic block copolymer formed a shapeless domain. Temperature‐controlled out‐of‐plane X‐ray diffraction (XRD) analysis of Langmuir–Blodgett (LB) films fabricated from both amphiphilic linear and cyclic block copolymers was performed to estimate the layer regularity at higher temperatures. Excellent heat‐resistant properties of organized molecular films created from the cyclic copolymer were confirmed. Both copolymer types showed clear diffraction peaks at room temperature, indicating the formation of highly ordered layer structures. However, the layer structures of the linear copolymers gradually disordered when heated. Conversely, the regularity of cyclic copolymer LB multilayers did not change with heating up to 50 °C. Higher‐order reflections (d₀₀₂, d₀₀₃) in the XRD patterns were also unchanged, indicative of a highly ordered structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 486–498     

High performance semiconducting polymers containing bis(bithiophenyl dithienothiophene)‐based repeating groups for organic thin film transistors

New dithienothiophene‐containing conjugated polymers, such as poly(2,6‐bis(2‐thiophenyl‐3‐dodecylthiophene‐2‐yl)dithieno[3,2‐b;2′,3′‐d]thiophene, 4 and poly(2,6‐bis (2‐thiophenyl‐4‐dodecylthiophene‐2‐yl)dithieno[3,2‐b;2′,3′‐d]thiophene, 8 have been successfully synthesized via Stille coupling reactions using dodecyl‐substituted thiophene‐based monomers, bistributyltin dithienothiophene, and bistributyltin bithiophene; these polymers have been fully characterized. The main difference between the two polymers is the substitution position of the dodecyl side chains in the repeating group. Grazing‐incidence X‐ray diffraction (GI‐XRD) gave clear evidence of edge‐on orientation of polycrystallites to the substrate. The semiconducting properties of the two polymers have been evaluated in organic thin film transistors (OTFTs). The two conjugated polymers 4 and 8 exhibit fairly high hole carrier mobilities as high as μ_ave = 0.05 cm²/Vs (I_ON/OFF = 3.42 × 10⁴) and μ_ave = 0.01 cm²/Vs, (I_ON/OFF = 1.3 × 10⁵), respectively, after thermal annealing process. The solvent annealed films underwent reorganization of the molecules to induce higher crystallinity. Well‐defined atomic force microscopy (AFM) topography supported a significant improvement in TFT device performance. The hole carrier mobilities of the solvent annealed films are comparable to those obtained for a thermally annealed sample, and were one‐order higher than those obtained with a pristine sample. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Photodegradation of polyaromatic hydrocarbons over thin film of TiO2 nanoparticles; a study of intermediate photoproducts

The photocatalytic degradation of saturated aqueous solution of naphthalene and anthracene was studied over thin films of porous TiO₂ particles on glass substrate, prepared by sol–gel process. Surface morphology and structural features were studied by SEM, TEM and Laser Raman Spectroscopy. These films have been found to be very efficient and the total photomineralisation of these organics to carbon dioxide and water occurs in air-equilibrated solution within 1 h. Concentration changes linearly with the illumination time, and high rate constants are obtained for the degradation of these organics. The pH of the solution changes with the irradiation time due to the formation of intermediate photoproducts, e.g., 5,8-dihydroxynaphthaquinone, and 9,10-anthraquinone, etc. Photodegradation mechanism and the detection of reaction intermediates have been discussed in details.     

Creep behavior of ultra‐thin polymer films

A novel microbubble inflation method has been used to determine the creep compliance of poly(vinyl acetate) and polystyrene ultra‐thin films (13–300 nm thick) at temperatures from below to above the glass temperature. We present results that suggest that time‐temperature and time‐thickness superposition hold in the glassy relaxation regime. Although time‐temperature superposition is found for the entire response curve for each thickness, we also find that time‐thickness superposition fails as the long‐time compliance is approached. This effect occurs because of a strong stiffening as the film thickness decreases. We also show first evidence of stiffening in the glassy regime of free standing films of polystyrene. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1952–1965, 2008     

Flexible transparent fluorinated nanohybrid with innovative heat‐resistance property—new technology proposal for fabrication of transparent materials using “crystalline” polymer

A new technology for the production of transparent material, using a “crystalline” polymer, is proposed in this study. In addition, a heat‐resistant transparent flexible plastic film with a high hydrophobic surface and a thermal decomposition temperature near 400 °C was created. Partially fluorinated crystalline polymer with switchboard‐type lamellae results high transparency as a consequence of the formation of a high‐density amorphous structure based on high‐temperature drawing just below the melting point at 250 °C. Melt‐compounding with montmorillonite modified by the long‐chain quaternary phosphonium with high coverage induces formation of a nanohybrid that retains transparency and also results in an increase in the thermal degradation temperature by over 50 °C. Through this technology, which results in heat‐resistance, transparency, and flexibility, the nano‐micro‐millimeter structures of solid‐state polymers are hierarchically controlled, which enables the creation of new materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1674–1690