Dual plasmonic‐enhanced bulk‐heterojunction solar cell incorporating gold nanoparticles into solution‐processed anode buffer layer and active layer

A dual plasmonic resonance effect on the performance of poly(3‐hexylthiophene) (P3HT):phenyl C61‐butyricacid methyl ester (PC61BM) based polymer solar cells (PSCs) has been demonstrated by selectively incorporating 25 nm colloidal gold nanoparticles (Au NPs) in a solution‐processed molybdenum oxide (MoO₃) anode buffer layer and 5 nm colloidal Au NPs in the active P3HT:PCBM layer. The devices exhibit up to ～20% improvement in power conversion efficiency which is attributed to the dual effect of localized surface plasmon resonance (LSPR) of Au NPs with enhanced light absorption and exciton generation. Our report shows a guideline on the usage of dual LSPR effect for the solution‐processed polymer solar cells to achieve high efficiencies. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Mobility Enhancement of P3HT‐Based OTFTs upon Blending with Au Nanorods

The mobility enhancement of organic thin‐film transistors based on poly(3‐hexylthiophene) (P3HT) by incorporating gold nanorods (Au NRs) is reported. Through varying the doping concentration and surface modifier of the Au NRs in P3HT matrix, the P3HT/Au composite with 0.5 mg mL^?1 pyridine‐capped Au NRs exhibits a hole mobility of 0.059 cm² V^?1 s^?1, this value is seven times higher than that of pristine P3HT. This remarkable improvement of mobility originates from the enhanced crystallinity and optimized orientation of P3HT after doping with Au NRs. In addition, the appropriate surface modification can produce more‐efficient hole conduction of Au NRs.     

Effect of solvent evaporation on the self‐assembly of poly(3‐hexylthiophene‐2,5‐diyl) and on the film morphology during electrospray deposition

A high‐voltage rectangular pulse was applied to the electro‐spray deposition (ESD) to control the evaporation‐induced self‐assembly of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT). Two groups of P3HT thin films were deposited by a series of high‐voltage rectangular pulses. Compared with the ESD driven by a constant voltage, the pulse‐driven ESD enables to probe the effect of solvent evaporation on the self‐assembly of P3HT molecules. The droplet size and the evaporation of residual solvent in the droplet determine the film morphology. Ultraviolet–visible absorption spectroscopy was used to identify the ordering of P3HT molecules in the films. The self‐assembly of P3HT molecules took place during the solvent evaporation which can be controlled by a combination of the pulse amplitude and the pulse interval. With an appropriate combination of the amplitude and the interval, the ESD produced a P3HT thin film with high chain ordering.

     

Coalescence of Cluster Beam Generated Sub‐2 nm Bare Au Nanoparticles and Analysis of Au Film Growth Parameters

In this work is presented the growth model for Au films grown on a carbon substrate at room temperature by using as building blocks Au nanoparticles (NPs) with 1.4 nm mean size generated via remote cluster beam synthesis and soft landing on the substrate. The key results highlighted in this work are that 1) the deposited nanoparticles coalesce at substrate level in such a way that the film growth is 3D, 2) newly formed nanoparticles at substrate level are predominantly magic number clusters and 3) coalescensce takes place as soon as two neighboring nanopartciles come closer than a critical distance. The film growth was investigated by TEM as a function of Au load, in the range 0–1.2 μg/cm². Two distinct regimes are identified: the “landing regime” and the “coalescence regime”. During the latter the film growth is 3D with a dynamic scaling exponent z of 2.13. Particular attention was devoted to the study of the evolution of the NP population from the moment they are generated with the cluster beam generator to the moment they land on the substrate and coalesce with other NPs. Our results show that 1) the NPs generated by the cluster beam are heterogeneous in size and are made by more than 95% by Au Magic numbers, mainly Au₂₀ and Au₅₅ and 2) kinetic processes (coalescence) at substrate level is capable of producing NPs populations made of larger Au magic numbers containing up to several thousands of Au atoms. Experimental and simulation results provide insight into the coalescence mechanism and provide strong evidence that the NPs coalesce when the nearest neighbor distance is below a critical mark. The critical distance is at its minimum 0.4‐0.5 nm and it is still unclear whether it is constant or not although the best matching simulation results seem to point to a superlinear dependence from the NP size difference between two neighboring candidate coalescing NPs. The coalescence phenomenon investigated in this work pinpoints the unique self‐organization properties of these small Au NPs in creating films with a stable edge‐to‐edge mean nearest neighbor distance of the order of 1.4 nm.     

Synthesis of a Au‐on‐Pd Heteronanostructure Stabilized by Citrate and its Catalytic Application

The preparation of Au‐on‐Pd heteronanostructure (HNS) using citrate‐stabilized polycrystalline Pd nanoparticles (NPs) as the seeds is described. The resulting Au‐on‐Pd HNS is characterized and it is found that the formation of Au‐on‐Pd HNS depends greatly on a ratio between Pd seeds and AuCl₄^? ions added and the optimal molar ratio is 10:1. If fewer AuCl₄^? ions are added (Pd/Au ratio is 100:1), the growth of Au NPs only occurs on part of the Pd seeds’ surface. The addition of more AuCl₄^? ions (Pd/Au ratio is 5:1) hinders the growth of Au NPs on the Pd seeds’ surface. To demonstrate the catalytic performance, the electrochemistry oxidation of ethanol and the reduction of p‐nitrophenol by NaBH₄ are chosen to examine the catalytic activity of Au‐on‐Pd HNS. Pd seeds, Au NPs, and poly(vinyl pyrrolidone) (PVP)‐stabilized PdAu nanoalloy are used as the references for comparison. In the first reaction, the catalytic reactivity of Au‐on‐Pd HNS is better than that of corresponding pure Pd or Au NPs, while the opposite occurs for the latter reaction. The catalytic activity of Au‐on‐Pd HNS is much higher than that of PVP‐stabilized PdAu nanoalloy.     

Surface‐enhanced Raman scattering spectroscopy via gold nanostars

Anisotropic metallic nanoparticles (NPs) have unique optical properties, which lend them to applications such as surface‐enhanced Raman scattering (SERS) spectroscopy. Star‐shaped gold (Au) NPs were prepared in aqueous solutions by the seed‐mediated growth method and tested for Raman enhancement using 2‐mercaptopyridine (2‐MPy) and crystal violet (CV) probing molecules. For both molecules, the SERS activity of the nanostars was notably stronger than that of the spherical Au NPs of similar size. The Raman enhancement factors (EFs) for 2‐MPy on Au nanostars and nanorods are comparable and estimated as greater than 5 orders of magnitude. However, the enhancement for CV on nanostars was significantly higher than for nanorods, in particular at CV concentrations of 100 nM or lower. This article is a US Government work and is in the public domain in the USA. Published in 2008 by John Wiley & Sons, Ltd.     

Fabrication of NIR‐Excitable SERS‐Active Composite Particles Composed of Densely Packed Au Nanoparticles on Polymer Microparticles

A simple fabrication method is demonstrated for surface‐enhanced Raman scattering (SERS)‐active plasmonic nanoballs, which consisted of Au nanoparticles (NPs) and core–shell polystyrene and amino‐terminated poly(butadiene) particles, by heterocoagulation and Au NP diffusion. The amount of Au NPs introduced into the core–shell particles increases with the concentration of Au NPs added to the aqueous dispersion of the core–shell particles. When the amount of Au NPs increases, closely packed, three‐dimensionally arranged and close‐packed Au NPs arrays are formed in the shells. Strong SERS signals from para‐mercaptophenol adsorbed onto composite particles with multilayered Au NPs arrays are obtained by near‐infrared (NIR) light illumination.     

Electrical behavior of amorphous indium–gallium–zinc oxide thin film transistors by embedding Au nanoparticles in the channel layer

We reported the effects on the electrical behavior of amorphous indium–gallium–zinc oxide (a-IGZO) thin film transistors (TFTs) after introducing various positions and sizes of Au nanoparticles (NPs) in the channel layer. These TFTs showed an off-current increase and threshold voltage (V_th) shift compared to conventional a-IGZO TFTs. The effects of Au NPs are explained to form the carrier conduction path which causes the current leakage in the channel layer, and act as either electron injection sites or trap sites. Therefore, this study demonstrates that the optimized control of size and position of Au NPs in the channel layer is crucial for its application in the electrical stability improvement and V_th control of a-IGZO TFTs.     

Synergistic Action of Alginate Chemical Reduction and Laser Irradiation for the Formation of Au Nanoparticles with Controlled Dimensions

Freestanding natural polymeric films with homogeneous dispersion of gold nanoparticles (Au NPs) are obtained via in situ reduction of gold(III) chloride trihydrate by sodium alginate (SA) biopolymer matrix, during water evaporation without the use of additional reducing agents. The size and size distribution of the prepared Au NPs can be tuned by changing the concentration of the precursor and/or the procedure of the films’ preparation. The nanocomposite films after preparation are stable in ambient conditions and can be used without the need of further processing, or can be redissolved in water. In the case of water dissolution, the aqueous solutions are irradiated with UV laser pulses turning the previously formed Au NPs into smaller ones with narrow size distributions through photofragmentation. This technique is proposed as a green way of synthesizing Au NPs of tunable size in aqueous solution of alginate, or incorporated in alginate freestanding polymeric films, that due to their biocompatibility can be used as passive labels or active sensors in biomedical applications.     

Highly Enhanced Emission of Visible Light from Core–Dual‐Shell‐Type Hybridized Nanoparticles

Core–dual‐shell‐type hybridized nanoparticles (NPs) having Au‐core/dye‐doped silica inner shell/Au outer shell are successfully fabricated by developing a biphasic process that is a kind of so‐called “one‐pot” method. The resulting hybridized NPs exhibit evidently about 20‐fold enhancement of fluorescence intensity, increase in fluorescence quantum yield, and decrease in fluorescence lifetime. These effects depend on the metal nanostructure being optimized, compared with the reference hybridized NPs with neither a Au‐core nor a Au outer shell, due to the gap‐mode effect induced by localized surface plasmon resonance in the core–dual‐shell‐type MIM‐like nanostructure. More detailed elucidation concerning the enhancement mechanism will provide the possibility of photonic device application, for example as a high‐performance point light source, nanolaser, or sensor for bioimaging in the visible region in the near future.     

Simple method to prepare size‐controllable gold nanoparticles in solutions and their applications on surface‐enhanced Raman scattering

We report here, for the first time, a simple method to prepare size‐controllable Au nanoparticles (NPs) in aqueous solutions from bulk Au substrates. First, chitosan (Ch)‐capped Au‐containing complexes were prepared by electrochemical oxidation–reduction cycles in 0.1 N NaCl and 1 g/l Ch solutions. Then the solutions were heated from room temperature to boiling at different heating rates to synthesize size‐controllable Au NPs. The particle sizes of the prepared Au(111) NPs could be controlled from 5 to 30 nm with an increase of the heating rate during preparation. Experimental results indicate that the prepared Au(111) NPs with diameters ranging from 10 to 30 nm can serve as surface‐enhanced Raman scattering active probes for molecules of rhodamine 6G. Copyright © 2010 John Wiley & Sons, Ltd.     

Laser printing and characterization of semiconducting polymers for organic electronics

Hybrid organic/inorganic thin-film transistors (TFTs) with bottom-contact configuration were fabricated using the Laser Induced Forward Transfer (LIFT) process. The semiconducting polymer P3HT was laser printed from a donor to a receiver substrate in order to form the active layer of the TFTs. With a single laser pulse, P3HT pixels were successfully printed. The printed material was analyzed morphologically by means of Optical Microscopy and its thickness was measured by profilometry. In addition, structural characterization of P3HT thin films before and after laser printing took place by using UV-Visible absorption spectroscopy and X-Ray Diffraction. It was found that the crystallinity of the investigated films is improved upon annealing. An organic thin-film transistor (OTFT) with laser printed P3HT pixel as a channel layer was then fabricated. The OTFTs indicated a field-effect mobility up to 2.23?10^?4 cm²/Vs and an on/off ratio on the order of 10–100.     

Molecular crystallization of rubrene thin films assisted by gold nanoparticles

We demonstrate that crystalline organic rubrene thin films can be obtained by a facile spin-coating method using gold (Au) nanoparticles (NPs). Dodecanethiol-functionalized Au NPs were dissolved with rubrene molecules in solvent and a thin film of Au/rubrene was prepared by a simple spin coating process. The results of confocal photoluminescence (PL) and absorption spectral mapping confirmed the local formation of orthorhombic crystalline structures of the Au/rubrene hybrid film, in contrast to the monoclinic structure of plain rubrene films. Further, the results of transmission electron microscopy (TEM) and X-ray diffraction analysis, as well as Raman spectroscopy measurements of the rubrene and Au/rubrene films suggested the formation of high crystalline Au/rubrene film. The molecular crystallization of the Au/rubrene hybrid film is attributed to the nucleation effect of the Au NPs.     

Laser printing of polythiophene for organic electronics

We report on the development of hybrid organic/inorganic thin-film transistors using regioregular poly-3-hexylthiophene (P3HT) semiconductor material deposited by means of the solid-phase Laser Induced Forward Transfer (LIFT) technique. P3HT pixels were LIFT-printed onto Au/Ti source and drain electrodes formed on silicon dioxide/p⁺-type Si substrate. Deposition of the P3HT pixels was investigated as a function of the laser fluence using donor substrates with and without a dynamic release layer. Device electrical characterization reveals efficient field-effect action of the bottom gate on the organic channel. The transfer I_DS-V_GS characteristics exhibit well-defined sub-threshold, linear and saturation regimes designating LIFT as a promising technique for hybrid organic/inorganic transistor technology.     

Identification of grain boundaries as degradation site in n‐channel organic field‐effect transistors determined via conductive atomic force microscopy

One important figure of merit for the commercial usability of organic transistors (OFETs) is their electrical stability. With the aim of identifying the microscopic location of degradation sites within a transistor channel, we have investigated the bias stress stability of OFETs by electrical measurements as well as by conductive atomic force microscopy. Air‐stable n‐channel FETs based on a N,N′‐bis(2‐ethylhexyl)‐1,7(1,6)‐dicyano‐perylene[3,4:9,10]bis (dicarboximide) were fabricated to understand the relation between the thin‐film morphology, the substrate temperature during the vacuum de position with the aim to fabricate transistors with a mobility not dominated by interface traps. The devices showed a maximum carrier mobility of (0.12 ± 0.01) cm²/V s and an on/off ratio up to 10⁷. The electrical performance as well as the bias stress behavior of the semiconductor thin‐films is significantly influenced by grain boundaries. For example, the grain boundary resistance was found to increase upon electrical stress by more than 150% (from 2 ± 0.2 GΩ to 5 ± 1.5 GΩ), while the resistance within the grains remains unchanged. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

High–Yield Production of Uniform Gold Nanoparticles with Sizes from 31 to 577 nm via One‐Pot Seeded Growth and Size‐Dependent SERS Property

In this work, uniform, quasi‐spherical gold nanoparticles (Au NPs) with sizes of 31–577 nm are prepared via one‐pot seeded growth with the aid of tris‐base (TB). Distinct from the seeded growth methods available in literature, the present method can be simply implemented by subsequently adding the aqueous dispersion of the 17 nm Au‐NP seeds and the aqueous solution of HAuCl₄ into the boiling aqueous TB solution. It is found that at the optimal pH range, the sizes of the final Au NPs and their concentrations are simply controlled by either the particle number of the Au seed dispersion or the concentration of the HAuCl₄ solution, while the latter enables us to produce large Au NPs at very high concentration. Moreover, as‐prepared Au NPs of various sizes are coated on glass substrates to test their surface‐enhanced Raman scattering (SERS) activities by using 4‐aminothiophenol (4‐ATP) molecules as probes, which exhibit “volcano type” dependence on the Au NP sizes at fixed excitation wavelength. Furthermore, the Au NPs with sizes of ≈97 and 408 nm exhibit the largest SERS enhancement at the excitation wavelength of 633 and 785 nm, respectively.     

Spin‐dependent‐magnetoresistance control by regulation of heat treatment temperature for magnetite nano‐particle sinter

The control of spin‐dependent‐magnetoresistance by regulation of the heat treatment (HT) temperature for magnetite (Fe₃O₃) nano‐particle sinter (MNPS) has been studied. The average nano‐particle size in the MNPS is 30nm and the HT was carried out from 400°C to 800°C. The HT of the MNPS varies the coupling form between adjacent magnetite nano‐particles and the crystallinity of that. The measurements on electrical resistance (ER), magnetoresistance (MR) and magnetization were performed between 4K and 300K. The behavior of the ER and MR considerably changes at the HT temperature of ～600°C. Below ～600°C the ER indicates the variable‐range‐hopping conduction behavior and the MR shows the large intensity in a wide temperature region. Above ～600°C the ER shows the indication of the Verwey transition near 110K like a bulk single crystal and the MR designates the smaller intensity. We consider that below ～600°C the ER and MR are dominated by the grain‐boundary conduction and above ～600°C those are determined by the inter‐grain conduction. The magnetic field application to the grain‐boundary region is inferred to cause the large enhancement of the MR.     

Fabrication and characterization of Au/SiO2 nanocomposite films grown by radio-frequency cosputtering

Au/SiO₂ nanocomposite films were prepared on Si wafers by cosputtering of SiO₂ and gold wires. Au/Si atomic ratios in Au/SiO₂ nanocomposite films were varied from 0.53 to 0.92 by controlling the length of gold wire to study the evolution of the crystallization of gold, the size of Au/SiO₂ nanocomposite particles, and the optical properties of as-deposited Au/SiO₂ nanocomposite films. An X-ray photoelectron spectroscopy reveals that Au exists as a metallic phase in the bulk of SiO₂ matrix. Dome-shaped Au/SiO₂ nanocomposite particles and both Au (1 1 1) and (2 0 0) planes were observed in a field-emission scanning electron microscopy and X-ray diffraction studies respectively. With an ultraviolet-visible, absorption peaks of Au/SiO₂ nanocomposite films were observed at 525 nm.     

不同形貌金纳米粒子的制备及其表面增强拉曼散射效应的研究

不同形状的金纳米粒子在表面增强拉曼散射(surface enhanced Raman scattering,SERS)中有不同的增强效果,多面体金纳米粒子具有多角结构,显示出比金纳米板更为明显的增强效果,近年来对其合成和性质的研究备受关注。该研究探究了十二面体,二十面体,三角板,球形四种形状的金纳米粒子在SERS中不同的增强效果。分别采用硼氢化钠还原法和以N,N-二甲基甲酰胺(DMF)为还原剂制备金三角纳米片和二十面体金纳米粒子,又以二十面体金纳米粒子为种子制备出十二面体金纳米粒子,并分别以以上三种不同形貌的金纳米粒子及球形金溶胶为基底,4-巯基吡啶,对巯基苯甲酸为探针分子检测了其在不同激发波长下的增强效果。透射电子显微镜结果表明金三角纳米板的平均边长为130nm,二十面体和十二面体金纳米粒子的粒径分别为100和120nm。三者的紫外可见吸收峰分别在589,598和544nm处。表面增强拉曼散射结果表明金多面体比金三角纳米板表现出更好的增强效果。     

Influence of polymer dielectric surface energy on thin‐film transistor performance of solution‐processed triethylsilylethynyl anthradithiophene (TES‐ADT)

This study investigates the correlation between surface energy of polymer dielectrics and the film morphology, microstructure, and thin‐film transistor performance of solution‐processed 5,11‐bis(triethylsilylethynyl) anthradithiophene (TES‐ADT) films. The low surface energy polyimide (PI) dielectric induced large grains with strong X‐ray reflections for spin‐cast TES‐ADT films in comparison to high surface en‐ ergy poly(4‐vinyl phenol) (PVP) dielectric. Furthermore, thin‐film transistors based on spin‐cast TES‐ADT films on PI dielectric exhibited enhanced electrical performance, small hysteresis, and high stability under bias stress with carrier mobility as high as 0.43 cm²/Vs and a current on/off ratio of 10⁷. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)