Copolyfluorenes containing bridged triphenylamine or triphenylamine: Synthesis,characterization, and optoelectronic properties

A novel aryl‐bridged triphenylamine derivative, 7‐t‐butyl‐5,5,9,9‐tetraaryl‐13b‐aza‐naphtho[3,2,1‐de]anthracene (ABTPA) was designed and synthesized. The alternating copolymers of ABTPA/dihexylfluorene ( P1 ) and triphenylamine (TPA)/dihexylfluorene ( P2 ) were synthesized by Suzuki coupling reaction. P1 shows excellent thermal stability with a decomposition temperature of 440 °C and a glass‐transition temperature of 326 °C. The HOMO energy levels of the two polymers are very close (?5.15 eV for P1 and ?5.13 eV for P2 ). The maximum absorption peak of P1 is red shifted by 23 nm with respect to P2 , because the incorporation of ABTPA units into the PF backbone enhances the electronic conjugation degree compared with the case of TPA units. The rigidity and the steric hindrance of the ABTPA in P1 result in a small Stokes shift and almost the same emission spectra of P1 between its film and solution. A PLED with simple configurations of ITO/ P1 /TNS (tetranaphthalen‐2‐yl‐silane)/Alq₃ (tris(8‐hydroxyquinolinolato)aluminum)/Al emits a blue light with emission peak at 436 nm, and exhibits a maximum current efficiency of 1.89 cd/A and a maximum luminance of 4183 cd/m², which is superior to the device with P2 as emissive layer under the identical conditions. These results indicate that ABTPA unit could be a very promising candidate to replace TPA unit and find widely application in organic/polymeric optoelectronic materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3651–3661, 2009     

Silole‐containing poly(diphenylacetylene): Synthesis,characterization, and light emission

A disubstituted polyacetylene consisting of a poly(diphenylacetylene) backbone and a 1,2,3,4,5‐pentaphenylsilole (SiC₄Ph₅) pendant, that is, ? {(C₆H₅) C?C [C₆H₄O(CH₂)₃C?CSiC₄Ph₅]}_n? (PS3DPA), was synthesized, and its light emission from both the backbone and the pendant was evaluated. The polymerization of C₆H₅C?CC₆H₄O(CH₂)₃C?CSiC₄Ph₅ with two ethynyl groups was effected with WCl₆–Ph₄Sn as the catalyst. The structure and properties of PS3DPA were characterized and evaluated by IR, UV, NMR, thermogravimetric analysis, differential scanning calorimetry, photoluminescence, and electroluminescence analyses. The ethynyl group of the diphenylacetylene moiety was polymerized exclusively, giving a soluble PS3DPA. The chloroform solution of PS3DPA showed a backbone emission that peaked at 522 nm, whereas the silole pendant was nonradiative at room temperature. The polymer did not show the aggregation‐induced emission phenomenon, probably because the silole clusters were difficult to form when the polymer chains aggregated because of the very high rigidity of the main chain. Intramolecular rotations of the phenyl groups of the silole moieties were responsible for the nonradiative decay of the silole chromophore. The intramolecular rotations, however, could be largely restricted in a cooling process of the polymer solution, showing cooling‐enhanced emission. The silole emission became dominant at lower temperatures. A multilayer electroluminescence device based on PS3DPA emitted a green light that peaked at 512 nm. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2487–2498, 2006     

Poly(fluorenevinylene) derivatives by Heck coupling: Synthesis,photophysics, and electroluminescence

Three new poly(fluorenevinylene) derivatives were synthesized, characterized, and used as emissive materials in light‐emitting diodes (LEDs). They were synthesized by Heck coupling of 9,9‐dihexyl‐2,7‐divinylfluorene with 2,7‐dibromo‐9,9‐dihexylfluorene, 2,3‐bis(4‐bromophenyl)quinoxaline, or 2,5‐bis(4‐bromophenyl)‐3,4‐diphenylthiophene to afford the polymers F , Q , and T , respectively. Polymers F and Q had medium number–average molecular weights (M_n ? 14,000) with relatively narrow polydispersity (1.3–1.6), while T was obtained as an oligomer (M_n ? 4000). All polymers were soluble in common organic solvents, such as tetrahydrofuran (THF), chloroform, dichloromethane, and toluene. They emitted blue‐greenish fluorescence light in dilute THF solution (444–491 nm), with photoluminescence (PL) quantum yields of 0.32–0.54, and in thin film (453–488 nm). LEDs with the configuration of ITO/PEDOT‐PSS/Polymer/Li:Al were fabricated and evaluated. The electroluminescence (EL) spectra of the Q and F polymers were very broad covering the blue–green–red region, whereas the spectrum of the polymer T was almost purely blue. The threshold electrical field for light emission of the devices was almost the same (?1.75 MV/cm). The external quantum efficiency of the devices of polymers Q and F was about 1.0 × 10^?3%, whereas that of polymer T was ?3.0 × 10^?5%. The fluorescence lifetime of polymers F and Q was significantly longer than that of the polymer T . © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4494–4507, 2006     

Highly substituted poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives having bulky phenyl and fluorenyl pendant groups: Synthesis,characterization, and electro‐optical properties

Two series of poly(2,3‐diphenyl‐1,4‐phenylenevinylene) (DP‐PPV) derivatives containing multiple bulky substituents were synthesized. In the first series, two different groups were incorporated on C‐5,6 positions of the phenylene moiety to increase steric hindrance and to obtain blue‐shifted emissions. In the second series, bulky fluorenyl groups with two hexyl chains on the C‐9 position were introduced on two phenyl pendants to increase the solubility as well as steric hindrance to prevent close packing of the main chain. Polymers with high molecular weights and fine‐tuned electro‐optical properties were obtained by controlling the feed ratio of different monomers during polymerization. The maximum photoluminescent emissions of the thin films are located between 384 and 541 nm. Cyclic voltammetric analysis reveals that the band gaps of these light‐emitting materials are in the range from 2.4 to 3.3 eV. A double‐layer EL device with the configuration of ITO/PEDOT/P4/Ca/Al emitted pure green light with CIE′1931 at (0.24, 0.5). Using copolymer P6 as the emissive layer, the maximum luminescence and current efficiency were both improved when compared with the homopolymer P4. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6738–6749, 2006     

Coumarin‐containing poly(fluorenediylvinylene)s: Synthesis,photophysics, and electroluminescence

Two new poly(fluorenediylvinylene)s (CV and CF) with coumarin side chains were synthesized via Heck coupling. The coumarin segments were attached to the C‐9 of fluorene through alkyl spacers. The polymers were soluble in common organic solvents such as tetrahydrofuran (THF), chloroform, dichloromethane, and toluene. The photoluminescence (PL), electroluminescence (EL), and electrochemical behavior of these polymers were studied. CV and CF thin films exhibited broad‐band, bluish‐green and orange PL emissions, with maxima at 475 and 585 nm, respectively. These PL maxima were redshifted in comparison with those measured in THF solutions. Aggregate formation played an important role in the solid state. The aggregation was more pronounced in CF thin films than CV thin films. Both polymers oxidized and reduced irreversibly. Light‐emitting devices (LEDs) with indium tin oxide hole‐injecting and aluminum electron‐injecting electrodes were prepared and studied. The LEDs made of CV emitted green light, and the LEDs made of CF exhibited an orange EL emissions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5750–5762, 2006     

Polyfluorenes containing tetraphenylthiophene segments: Synthesis,photophysics, and electroluminescence

2,5‐Bis(4‐bromophenyl)‐3,4‐diphenylthiophene was synthesized from benzyl chloride and sulfur and through the subsequent bromination of the intermediate 2,3,4,5‐tetraphenylthiophene. It was condensed with 2,7‐dibromo‐9,9‐dihexylfluorene via a nickel‐mediated Yamamoto coupling reaction to afford a new series of statistical copolymers with various compositions. In addition, poly(9,9‐dihexylfluorene) (PF) was synthesized under the same conditions for comparison. All the polymers were soluble in common organic solvents such as tetrahydrofuran (THF), chloroform, and dichloromethane. Their glass‐transition temperatures increased with an increase in the tetraphenylthiophene (TPT) content in the polymers, and they were 63–149 °C. The solutions of the polymers in THF emitted intense blue light with a photoluminescence maximum at 418–440 nm and quantum yields of 0.32–0.62. Thin films of the polymers with TPT fractions lower than 20 mol % emitted blue‐green light with two well‐resolved peaks at 445 and 520 nm and an optical band gap of about 2.85 eV. A thin film of the polymer with aTPT fraction of 50 mol % emitted pure blue light with a maximum at 419 nm and an optical band gap of 3.28 eV. An enhancement of the light‐emitting‐diode brightness by a factor of ～8 with respect to that of PF was achieved in apolymer containing 5 mol % TPT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4015–4026, 2006     

Synthesis and characterization of novel germanium‐containing poly(p‐phenylenevinylene) derivatives

Novel blue‐emitting germanium‐containing poly(p‐phenylenevinylene) (PPV) derivatives with well‐defined conjugation lengths were synthesized via Wittig‐condensation polymerizations. The polymers can be color‐tuned by the introduction of various chromophores into the PPV‐based polymer backbones. The photoluminescence (PL) spectra of the polymers, GePVK (containing carbazole moieties), GeMEH (containing dialkoxybenzene moieties), and GePTH (containing phenothiazine moieties), were found to exhibit blue, greenish blue, and green emissions, respectively. GePTH produces more red‐shifted emission than GeMEH and GEPVK, resulting in green emission, and the solution and solid state PL spectra of GePVK consist of almost blue emission. The electroluminescence spectra of GeMEH and GePTH contain yellowy green and yellow colors, respectively. Interestingly, GePVK exhibits white emission with CIE coordinates of (0.33, 0.37) due to electroplex emission in the light‐emitting diodes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 979–988, 2008     

Synthesis and characterization of thermally crosslinkable hole‐transporting polymers for PLEDs

Two new thermally crosslinkable hole‐transporting polymers, X‐PTPA and X‐PCz, were synthesized via Yamamoto coupling reactions. The number‐averaged molecular weights (M_n) of X‐PTPA and X‐PCz were found to be 45,000 and 48,000, respectively, and therewith, polydispersity indices were of 1.8 and 1.7, respectively. Thermally crosslinked X‐PTPA and X‐PCz exhibit excellent solvent resistance and stable optoelectronic properties. The UV–visible maximum absorption peaks of X‐PTPA and X‐PCz in the thin film state are at 389 and 322 nm, respectively. The HOMO levels of X‐PTPA and X‐PCz are estimated to be ?5.27 and ?5.39 eV, respectively. Multilayered devices (ITO/crosslinked X‐PTPA or X‐PCz/SY‐PPV/LiF/Al) were fabricated with SY (SuperYellow) as the emitting layer. The maximum efficiency of the multilayered device with a crosslinked X‐PTPA layer is approximately three times higher than that of the device without a crosslinked X‐PTPA layer and much higher than that of the crosslinked X‐PCz device. This result can be explained by the observations that crosslinked X‐PTPA produces increased electron accumulation within the emitter, SY, and also efficient exciton formation due to improved charge balance. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5111–5117     

Synthesis,characterization, and electroluminescence of polyfluorene copolymers containing T‐shaped isophorone derivatives

We have successfully synthesized a series of new fluorene‐based copolymers, poly[(9,9‐bis(4‐octyloxy‐phenyl)fluorene‐2,7‐diyl)‐co‐[2(3{2[4(2{4[bis(bromophenyl‐4yl) amino]phenyl}vinyl)‐2,5‐bisoctyloxyphenyl]vinyl}‐5,5‐dimethyl‐cyclohex‐2‐enylidene)malononitrile] (PFTBMs), with varying molar ratios of the low‐energy band gap comonomer, 2(3{2[4(2{4[bis(4‐bromophenyl)amino]phenyl}vinyl)‐2,5‐bisoctyloxyphenyl]vinyl}‐5,5‐dimethyl‐cyclohex‐2‐enylidene)malononitrile (BTBM). To prepare BTBM (which has a T‐shaped structure) from triphenylamine, dialkoxy phenyl, and isophorone, we introduced three individual segments of an isophorone derivative containing two cyanide groups at the carbonyl position, a dialkoxy phenyl group for increased solubility, and a triphenyl amine for effective charge transfer. Furthermore, we introduced vinyl linkages between each segment to increase the length of π‐conjugation. The synthesized polyfluorene copolymers with the BTBM, PFTBMs, were synthesized via palladium‐catalyzed Suzuki coupling reactions. The photoluminescence emission spectra of the synthesized polymers in solution did not show significant energy transfer from PBOPF segments to the BTBM units. Light‐emitting devices based on these polymers were fabricated with an indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)/polymers/Balq/LiF/Al configuration. Examination of the electroluminescence emission of the synthesized polymers showed that the maximum wavelength shifted continuously toward long wavelengths with as the number of BTBM units in the polymer main chain was increased. In particular, a device using PFTBM 05 exhibited a maximum brightness of 510 cd/m² and a maximum current efficiency of 0.57 cd/A. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 82–90, 2010     

Synthesis,characterization, and optoelectronic properties of hyperbranched polyfluorenes containing pendant benzylether dendrons

Linear polyfluorenes with low generation of side benzylether dendrons ( PLG0 , PLG1 ) and hyperbranched polyfluorenes with 1,3,5‐benzene branch unit ( PHG0 and PHG1 ) were prepared by the Suzuki coupling reaction to investigate the structural effect on optoelectronic properties. Their optical properties, both in solution and film state, were investigated using absorption and photoluminescence (PL) spectra. The excimer emission of polyfluorene at about 530 nm, induced by thermal annealing, was completely suppressed by the hyperbranched structure, but the suppression was not obvious by the side benzylether dendrons. The optoelectronic performance of the EL devices (ITO/PEDOT:PSS/polymer/Ca/Al) was strongly dependent upon chemical structures of the emitting polyfluorenes. The hyperbranched PHG0 with zero generation of benzylether side groups revealed the best device performance, with maximal luminance and maximal luminance efficiency of 2350 cd/m² and 0.33 cd/A, respectively. The results suggest that incorporation of branch units with low generation of benzylether dendrons is an effective way to improve annealing stability and EL performance of the polyfluorenes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5945–5958, 2008     

Synthesis,photophysics, theoretical modeling,and electroluminescence of novel 2,7‐carbazole‐based conjugated polymers with sterically hindered structures

2,7‐dibromo‐N‐hexylcarbazole is successfully synthesized in three steps with an overall 37% yield. Novel 2,7‐carbazole‐based sterically hindered conjugated polymers are further synthesized. In the backbone structure of polymer P1 , alkylated bithiophene moiety is β‐substituted with dodecyl chains on both thiophene rings, adopting the tail‐to‐tail configuration. While for polymers P2 and P3 , partially planarized thieno[3,2‐b]thiophene moiety ( P2 ) and β‐pentyl substituted thieno[3,2‐b]thiophene ( P3 ) are incorporated. All polymers demonstrate efficient blue‐to‐green light emission, good thermal stability (T_d ≥ 379 °C), and high glass transition temperatures (T_g = 118 °C). The optical and electronic properties of the resulted polymers are tuned by the incorporated alkyl chains. For instance, the incorporation of β‐pentyl group in thieno[3,2‐b]thiophene moiety endows P3 with blue‐shifted photophysical spectra, reduced fluorescence quantum yield and larger band gap in comparison with P2 . The steric effect of incorporated alkyl chains is further illustrated by geometry optimization of three model oligomers (analogues to the repetition units of P1–P3 ) using density functional theory. Sterically hindered polymers P1 and P2 exhibit high charge transport ability and moderate electroluminescent properties in primarily tested single‐layer light‐emitting diodes (configuration: ITO/PEDOT:PSS/Polymer/Ca/Ag). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7725–7738, 2008     

Blue‐emitting poly(1,3‐phenylenevinylene) derivatives: Effect of substitution patterns on optical properties

Blue‐emitting poly{[5‐(diphenylamino)‐1,3‐phenylenevinylene]‐alt‐(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)} ( 3 ), poly{[5‐bis‐(4‐butyl‐phenylamino)‐1,3‐phenylenevinylene]‐alt‐(1,3‐phenylene vinylene)} ( 4 ), and poly(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene) ( 5 ) were synthesized by the Wittig–Horner reaction. Although polymers 3–5 possess fluorescent quantum yields of only 13–34% in tetrahydrofuran solution, their films appear to be highly luminescent. Attachments of substituents tuned the emission color of thin films to the desirable blue region (λ_max = 462–477 nm). Double‐layer light‐emitting‐diode devices with 3 and 5 as an emissive layer produced blue emission (λ_em = 474 and 477 nm) with turn‐on voltages of 8 and 11 V, respectively. The external quantum efficiencies were up to 0.13%. © 2005Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2800–2809, 2005     

Synthesis,characterization, and photovoltaic properties of dithienylbenzobisazole‐dithienylsilole copolymers

Three conjugated polymers comprised of dioctyl‐dithieno‐[2,3‐b:2',3'‐d]silole and a donor‐acceptor‐donor triad of either cis‐benzbisoxazole, trans‐benzobisoxazole or trans‐benzobisthiazole were synthesized via the Stille cross‐coupling reaction. The impact of varying the heteroatoms and/or the location within the benzobisazole moiety on the optical and electronic properties of the resulting polymers was evaluated via cyclic voltammetry and UV‐Visible spectroscopy. All of the polymers have similar optical band‐gaps of ～1.9 eV and highest occupied molecular orbital levels of ? 5.2 eV. However, the lowest unoccupied molecular orbitals (LUMO) ranged from ? 3.0 to ? 3.2 eV. Interestingly, when the polymers were used as donor materials in bulk‐heterojunction photovoltaic cells with PC₇₁BM as the electron‐acceptor, the benzobisoxazole‐based polymers gave slightly better results than the benzobisthiazole‐containing polymers with power conversion efficiencies up to 3.5%. These results indicate that benzobisoxazoles are promising materials for use in OPVs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1533–1540     

Synthesis and electrochemical and electroluminescent properties of N‐phenylcarbazole‐substituted poly(p‐phenylenevinylene)

An N‐phenylcarbazole‐containing poly(p‐phenylenevinylene) (PPV), poly[(2‐(4′‐carbazol‐9‐yl‐phenyl)‐5‐octyloxy‐1,4‐phenylenevinylene)‐alt‐(2‐(2′‐ethylhexyloxy)‐5‐methoxy‐1,4‐phenylenevinylene)] (Cz‐PPV), was synthesized, and its optical, electrochemical, and electroluminescent properties were studied. The molecular structures of the key intermediates, the carbazole‐containing boronic ester and the dialdehyde monomer, were crystallographically characterized. The polymer was soluble in common organic solvents and exhibited good thermal stability with a 5% weight loss at temperatures above 420 °C in nitrogen. A cyclic voltammogram showed the oxidation peak potentials of both the pendant carbazole group and the PPV main chain, indicating that the hole‐injection ability of the polymer would be improved by the introduction of the carbazole‐functional group. A single‐layer light‐emitting diode (LED) with a simple configuration of indium tin oxide (ITO)/Cz‐PPV (80 nm)/Ca/Al exhibited a bright yellow emission with a brightness of 1560 cd/m² at a bias of 11 V and a current density of 565 mA/cm². A double‐layer LED device with the configuration of ITO/poly(3,4‐ethylenedioxy‐2,5‐thiophene):poly (styrenesulfonic acid) (60 nm)/Cz‐PPV (80 nm)/Ca/Al gave a low turn‐on voltage at 3 V and a maximum brightness of 6600 cd/m² at a bias of 8 V. The maximum electroluminescent efficiency corresponding to the double‐layer device was 1.15 cd/A, 0.42 lm/W, and 0.5%. The desired electroluminescence results demonstrated that the incorporation of hole‐transporting functional groups into the PPVs was effective for enhancing the electroluminescent performance. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5765–5773, 2005     

Synthesis and opto‐electrical properties of dendron‐containing poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives

A new series of poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives containing dendritic side groups were synthesized. Different generations of dendrons were integrated on the pendant phenyl ring to investigate their effect on optical and electrical properties of final polymers. Homopolymers can not be obtained via the Gilch polymerization because of sterically bulky dendrons. By controlling the feed ratio of different monomers during polymerization, dendron‐containing copolymers with high molecular weights were obtained. The UV–vis absorption and photoluminescent spectra of the thin films are pretty close; however, quantum efficiency is significantly enhanced with increasing the generation of dendrons. The electrochemical analysis reveals that hole‐injection is also improved by increasing dendritic generation. Double‐layer light‐emitting devices with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al were fabricated. High generation dendrons bring benefit of improved device performance. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3440–3450, 2007     

Simple Silole‐Containing Polyfluorene for White Electroluminescence with Simultaneous Blue,Green, and Red Emission

Novel conjugated silole‐containing polyfluorenes, with green‐ and red‐emissive siloles on the backbone of the blue‐emissive polyfluorene are synthesized for white light electroluminescence (EL) from a single polymer with simultaneous red, green, and blue (RGB) emission. The CIE coordinates (0.33, 0.36) of the white light EL spectra are very close to that for pure white light (0.33, 0.33). The EL spectra are also quite stable at different applied voltages or brightness. The relative intensities for the three RGB peaks, at 450, 505, and 574 nm, were 0.94, 1, and 0.97, respectively, which demonstrates a balanced simultaneous RGB emission. A maximum luminous efficiency of 2.03 cd · A⁻¹ for a brightness of 344 cd · m⁻², and a luminous efficiency of 1.86 cd · A⁻¹ for a more practical brightness of 2 703 cd · m⁻², were achieved.

     

White electroluminescence from a single polyfluorene containing bis‐DCM units

A series of fluorene‐based copolymers composed of blue‐ and orange‐light‐emitting comonomers were synthesized through palladium‐catalyzed Suzuki coupling reactions. 9,9‐Dihexylfluorene and 2‐(2,6‐bis‐{2‐[1‐(9,9‐dihexyl‐9H‐fluoren‐2‐yl)‐1,2,3,4‐tetrahydroquinolin‐6‐yl]‐vinyl}‐pyran‐4‐ylidene)‐malononitrile (DCMF) were used as the blue‐ and orange‐light‐emitting chromophores, respectively. The resulting single polymers exhibited simultaneous blue (423/450 nm) and orange (580–600 nm) emissions from these two chromophores. By adjusting the fluorene and DCMF contents, white light emission could be obtained from a single polymer; a device with an ITO/PEDOT:PSS/polymer/Ca/Al configuration was found to exhibit pure white electroluminescence with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33, 0.31), a maximum brightness of 1180 cd/m², and a current efficiency of 0.60 cd/A. Furthermore, the white light emission of this device was found to be very stable with respect to variation of the driving voltage. The CIE coordinates of the device were (0.32, 0.29), (0.32, 0.29), and (0.33, 0.31) for driving voltages of 7, 8, and 10 V, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3380–3390, 2007     

Syntheses and electroluminescence properties of conjugated poly(p‐phenylene vinylene) derivatives bearing dendritic pendants

A series of new poly(p‐phenylene vinylene) derivatives with different dendritic pendants—poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE–PPV), poly{2‐[3′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBE–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBD–PPV), and poly[(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)‐co‐(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)] (BBE‐co‐BBD–PPV; 1:1)—were successfully synthesized according to the Gilch route. The structures and properties of the monomers and the resulting conjugated polymers were characterized with ¹H and ¹³C NMR, elemental analysis, gel permeation chromatography, thermogravimetric analysis, ultraviolet–visible absorption spectroscopy, photoluminescence, and electroluminescence spectroscopy. The obtained polymers possessed excellent solubility in common solvents and good thermal stability, with a 5% weight loss temperature of more than 328 °C. The weight‐average molecular weights and polydispersity indices of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were in the range of 1.33–2.28 × 10⁵ and 1.35–1.53, respectively. Double‐layer light‐emitting diodes (LEDs) with the configuration of indium tin oxide/polymer/tris(8‐hydroxyquinoline) aluminum/Mg:Ag/Ag devices were fabricated, and they emitted green‐yellow light. The turn‐on voltages of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were approximately 5.6, 5.9, 5.5, 5.2, and 4.8 V, respectively. The LED devices of BE–PPV and BD–PPV possessed the highest electroluminescent performance; they exhibited maximum luminance with about 860 cd/m² at 12.8 V and 651 cd/m² at 13 V, respectively. The maximum luminescence efficiency of BE–PPV and BD–PPV was in the range of 0.37–0.40 cd/A. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3126–3140, 2005