Self‐crosslinking borate anions for the production of tough UV‐cured polyelectrolyte surfaces

The first anion with four polymerizable groups has been synthesized and used to produce durable, crosslinked polyelectrolyte (PE) coatings in a single step. Sodium tetrakis(4‐vinylphenyl)borate (NaBSty₄) was produced by the reaction of BCl₃ and the Grignard of 4‐bromostyrene. The full series of borates NaBPh_xSty_4?x, x = 1?3, were also synthesized analogously by reaction of the styryl‐Grignard and PhBCl₂, Ph₂BCl, or Ph₃B. Anion exchange of the borates with tributyl 4‐vinylbenzylphosphonium chloride gave a family of organic salts developed for applications in photopolymerized coatings. The percent UV cure of the polymer films was determined by infrared spectroscopy and this relative level of curing was corroborated by differential scanning calorimetry analysis. The degree of crosslinking imparted to the polymer films by the different monomers has resulted in varied mechanical properties, which were probed by diamond tip scratch tests and nanoindentation. These clearly demonstrated that as the number of polymerizable groups increased, the film hardness increased correspondingly. The final hardness of the films exceeds those of other related systems and identifies styryl borates as viable crosslinking additives in UV curable technologies, especially in the production of durable PE films. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Ionic poly(p‐phenylene terephthalamide)s: Preparation and characterization

The preparation and characterization of two types of ionic poly(p‐phenylene terephthalamide) (PPTA) is described. A sufficient number of ionic groups were added to render modified PPTA soluble in dimethylsulfoxide (DMSO). In one type, a hydrogen atom of the amide group was replaced by an ionic propanesulfonate group. In the other type, one of the hydrogen atoms on the phenylene ring was replaced by an ionic sulfonate group. The ionic PPTAs in DMSO showed an upturn in viscosity at very low concentrations that was characteristic of the polyelectrolyte behavior. Fourier transform infrared spectra of these samples were also studied. When the ionic group was attached at the end of the short propane side chain, the intensity of both the free and hydrogen‐bonded N? H stretching mode was reduced compared with that of PPTA. Depending on the location of the ionic group, there were some changes in the intensity and wave number of the asymmetric and symmetric vibrations of the ionic SO group and the stretching mode of the carbonyl group. In both ionic PPTAs, there was an upward shift in the frequency of the symmetric vibrations of the sulfonate ion when the counterion, having been monovalent, became divalent. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2653–2663, 2001     

Imidazolium‐based poly(ionic liquid)s with poly(ethylene oxide) main chains: Effects of spacer and tail structures on ionic conductivity

Ten types of cationic glycidyl triazole polymers (GTPs) are prepared from combinations of five alkyl‐imidazolium units (methyl‐, ethyl‐, n‐propyl‐, iso‐propyl‐, and n‐butyl‐imidazoliums) and two spacers [di‐ and tri(ethylene glycol)s]. Since these poly(ionic liquid)s are prepared from the same sample of glycidyl azide polymer by postfunctionalization method, they have the same degree of polymerization. Therefore, the structure–property relationship can be discussed without influence of molecular weight difference. The samples are characterized by NMR, differential scanning calorimetry, and thermogravimetric analysis. The ionic conductivity data are obtained by impedance measurements. The GTPs with the tri(ethylene glycol) spacer and ethyl‐ and n‐butyl‐imidazolium units afford the highest anhydrous conductivity of 1.5 × 10^?5 S cm^?1 at 30 °C. Based on electrode polarization (EP) analysis, we calculate the conducting ion (carrier) concentration and mobility. We discuss the effect of the spacer and N‐alkyl tail structures on the ionic conductivity using the data obtained by EP analysis and X‐ray diffraction. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2896–2906     

Ionic poly(p‐phenylene terephthalamide)s: Solubility and thermal stability

Ionic sulfonate groups were incorporated onto molecules of the rigid‐rod polymer poly(p‐phenylene terephthalamide) (PPTA) in two different positions. In one type, S‐PPTA, ionic sulfonate groups were attached to the phenylene ring of the backbone chain. S‐PPTA solubility was achieved in dimethylsulfoxide (DMSO) when 50% of the repeat units contained an ionic group. In the second type, PPTA‐PS, where ionic propanesulfonate groups served as side chains, solubility was achieved in DMSO when 30% of the repeat units contained the ionic group. For both of the partially sulfonated ionic polymers, the thermal stability was enhanced in comparison with the stability of the acid‐form polymers, but it was less than that of PPTA. The effect was more dramatic when the ionic groups were located at the end of side chains. The nature of the counterion also played a role, with doubly ionized calcium giving the best results. Polarized light micrographs of the ionic PPTA polymers displaced birefringent patterns and indicated that greater rigidity was present when the ionic groups were directly attached to the backbone, rather than at the end of a short side chain. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2888–2897, 2001     

High thermal conductivity of polymerizable liquid‐crystal acrylic film having a twisted molecular orientation

The aligned films, the homogeneous film, the 90°‐twisted film and the 180°‐twisted film, have been prepared by immobilizing the polymerizable liquid crystals under the UV irradiation. The relation between the thermal conductivity and the aligned molecular direction of the films was investigated. It is indicated that the additional thermal transmission effect, which the increase of the thermal conductivity may be induced, would exist in the twisted films. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1419–1425, 2006     

Conversion of poly(ethylene‐alt‐tetrafluoroethylene) copolymers into polytetrafluoroethylene by direct fluorination: A convenient approach to access new properties at the ETFE surface

Direct fluorination of poly(ethylene‐alt‐tetrafluoroethylene) copolymer (ETFE) was carried out on commercially available ETFE films with pure fluorine gas at ambient atmosphere. Reaction temperature was either 95 °C or 150 °C and exposure time was 20 hours. Analysis of the fluorinated samples was performed by attenuated total reflection Fourier transform Infrared, confocal micro‐Raman and ¹H and ¹⁹F magic angle spinning nuclear magnetic resonance spectroscopies, scanning electron microscopy, electron diffraction and X‐Ray photoelectron spectroscopies, contact angle determination, atomic force microscopy and nanoindentation measurements, and compared to those of the virgin ETFE copolymer. Integrity of the bulk materials was verified by investigating the thermal behavior of the polymers by thermogravimetric analysis and differential scanning calorimetry. Evidence for the formation of a homogeneous layer of polytetrafluoroethylene with a thickness of several microns at the surface of the copolymers with no degradation of the materials was observed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

New Architecture of Liquid‐Crystalline Polymers from Fluorinated Vinylcyclopropanes

A new class of fluorinated polymers was prepared by radical ring‐opening homopolymerization of vinylcyclopropane monomers with a perfluorinated (CF₂)_nF chain (n = 6, 8, or 10). The polymers were in fact copolymers composed of 1,5‐linear and cyclobutane isomer units, the relative content of which depended on n. Surprisingly, they formed liquid‐crystalline mesophases (SmB_d and/or SmA_d), which was attributed to phase separation of the incompatible fluorocarbon and hydrocarbon components of the repeat unit.     

Amphiphilic Comb‐Like Poly(oxyethylene) and Its Complexes with LiClO4: Synthesis and Mesomorphic Behavior

Summary: We prepared an amphiphilic, comb‐like poly(oxyethylene) containing decyl‐tri(oxyethylene) amphiphiles in the side chain using a polymer analogous reaction to obtain a novel nonionic amphiphilic polymeric system with high molecular weight. The amphiphilic comb‐like poly(oxyethylene) itself only showed a side‐chain crystalline phase below its melting temperature of −31 °C. When the polymer was mixed with lithium perchlorate, a smectic liquid‐crystalline phase appeared. The ordered phases of the polymer and the polymer mixture were studied by differential scanning calorimetry, polarized optical microscopy, and X‐ray diffraction.

POM image (200 X) of D3OTP1 at room temperature.     

Nanostructured ion-conductive films: Layered assembly of a side-chain liquid-crystalline polymer with an imidazolium ionic moiety

An ion-conductive mesogenic monomer with an imidazolium ionic moiety has been designed to obtain self-assembled materials forming ionic layers. Self-standing polymer films are prepared by in situ photopolymerization of the monomer that forms homeotropic monodomain on a normal glass substrate in the smectic A phase. Macroscopically oriented, layered nanostructures are formed in the film. The ionic conductivity parallel to the smectic layer has been measured for the oriented film. In the smectic A phase at 150 °C, the magnitude of conductivity is about 10⁻² S cm⁻¹. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3486–3492, 2003     

Enhanced photopolymerization of dimethacrylates with ketones,amines, and iodonium salts: The CQ system

The kinetics and mechanism of the photopolymerization of dimethacrylates using three‐component initiation systems consisting of camphorquinone (CQ), diphenyliodonium hexafluorophosphate (Ph₂IPF₆), and either N,N,3,5‐tetramethylaniline (TMA) or N,N‐dimethylbenzylamine or triethylamine were studied by photo‐DSC and UV‐visible spectroscopy. The effect of monomer structure on the curing kinetics and photobleaching were also investigated. Photo‐DSC studies showed fivefold increases in polymerization rate when all three components were present and the kinetics followed the trend: CQ/amine/Ph₂IPF₆ ? CQ/amine > CQ/Ph₂IPF_6.. For both CQ/amine/Ph₂IPF₆ and CQ/amine systems, the CQ was rapidly photobleached during the photo‐DSC timescale but for the systems without amine there was an induction stage before CQ photobleaching was evident. Studies of the effect of monomer type on the photobleaching rate show that the photobleaching behavior was independent of monomer structure. Three photoinitiation mechanisms have been proposed. The reaction mechanism of the CQ/amine/Ph₂IPF₆ system involves the reduction of the excited CQ molecule by the amine to form ketyl and aminoalkyl radicals, followed by the irreversible oxidation of the amine, and to a lesser extent, the ketyl radical by the iodonium salt, to form an initiating radical. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Atom transfer radical polymerization directly from poly(vinylidene fluoride): Surface and antifouling properties

The direct preparation of grafting polymer brushes from commercial poly (vinylidene fluoride) (PVDF) films with surface‐initiated atom transfer radical polymerization (ATRP) is demonstrated. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the hydrophilic monomers from the PVDF surface. Homopolymer brushes of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) and poly (ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the PVDF surface. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance/Fourier transform infrared spectroscopy, and atomic force microscopy. A kinetic study revealed a linear increase in the graft concentration of poly[2‐(N,N‐dimethylamino)ethyl methacrylate] (PDMAEMA) and poly[poly(ethylene glycol) monomethacrylate] (PPEGMA) with the reaction time, indicating that the chain growth from the surface was consistent with a controlled or living process. The living chain ends were used as macroinitiators for the synthesis of diblock copolymer brushes. The water contact angles on PVDF films were reduced by the surface grafting of DMAEMA and PEGMA. Protein adsorption experiments revealed a substantial antifouling property of PPEGMA‐grafted PVDF films and PDMAEMA‐grafted PVDF films in comparison with the pristine PVDF surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3434–3443, 2006     

Surface modification of a liquid‐crystalline polymer for copper metallization

The effects of different surface modifications on the adhesion of copper to a liquid‐crystalline polymer (LCP) were investigated with X‐ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy, contact‐angle measurements, and pull tests. High pull‐strength values were achieved when copper was sputter‐deposited onto plasma and reactive‐ion‐etching (RIE)‐pretreated LCP surfaces. The values were comparable to the reference pull strengths obtained with laminated copper on the LCP. The adhesion was relatively insensitive to the employed feed gas in the pretreatments. The surface characterizations revealed that for RIE and plasma treatments, the enhanced adhesion was attributable to the synergistic effects of the increased surface roughness and polar component of the surface free energy of the polymer. However, if the electroless copper deposition was performed on RIE‐ or plasma‐treated surfaces, very poor adhesion was measured. Good adhesion between the LCP substrate and electrolessly deposited copper was achieved only in the case of wet‐chemical surface roughening as a result of the creation of a sufficient number of mechanical interlocking sites, together with a significant loss of oxygen functionalities, on the surface. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 623–636, 2003     

Photoluminescent,liquid‐crystalline,and electrochemical properties of para‐phenylene‐based alternating conjugated copolymers

Novel liquid‐crystalline alternating conjugated copolymers [ P(P(6)CN‐alt‐Cz) and P(P(6)CN‐alt‐MeP) ] with phenylene and carbazolylene or phenylene with methyl substitution onto the main chain have been synthesized through palladium‐catalyzed Suzuki coupling reactions. The influence of the incorporation of carbazolylene and the substituted phenylene into the main chain on the thermal, mesomorphic, and luminescent properties has been investigated by Fourier transform infrared spectroscopy, thermogravimetry, differential scanning calorimetry, polarized optical microscopy, ultraviolet–visible spectroscopy, photoluminescence (PL), and cyclic voltammetry. These polymers show highly thermal stability, losing little of their weights when heated to 360 °C. The conjugated copolymers exhibit liquid crystallinity at elevated temperature. The existence of the chromophoric terphenyl core endows the copolymers with high PL and the polymer P(P(6)CN‐alt‐Cz containing carbazolylene unit can emit more pure blue light. All the copolymer films with low band gaps about 2.3–2.4 eV undergo reversible oxidation and reduction processes, significantly lower than the band gap of poly(p‐phenylene). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 434–442, 2010     

Linear and A2+B3‐type hyperbranched polyesters comprising phenylbenzothiazole unit: Preparation,liquid crystalline,and optical properties

Novel liquid crystalline (LC) hyperbranched (HB) polyesters comprising phenylbenzothiazole (PBT) unit as mesogen in the interiors were prepared at various feed mole ratios (A₂/B₃) by solution polycondensation of a dioxydiundecanol derivative of PBT (A₂ monomer) with trimesic acid trimethyl ester (B₃ monomer) via A₂+B₃ approach and their LC and optical properties were investigated. Analogous linear polyesters containing the PBT unit in the main chains were also prepared by the solution polycondensation of A₂ monomer with aromatic or aliphatic dimethyl esters. FTIR and ¹H‐NMR spectroscopies indicated that the HB polyesters are produced without gelation during the polycondensation and have degree of branching (DB) of 7–46%. The structures of HB polymers changed depending on the feed mole ratios and the polymer prepared in the mole ratio of A₂/B₃ = 3/2 had the highest inherent viscosity and DB. Acetylation of terminal OH group‐having HB polyesters prepared in excess mole ratios of A₂/B₃ afforded ones bearing acetoxy groups in the terminals. DSC measurements, polarizing microscope observations of textures, and X‐ray analyses suggested that only the terminal OH group‐having HB polymer prepared in the mole ratio of A₂/B₃ = 3/1 form smectic C phase. In the linear polymers, the polymers derived by using the aromatic dimethyl esters had no LC melt, but those from the aliphatic dimethyl esters formed LC smectic C phase. The acetoxy group‐bearing HB polymers showed more stable smectic A or C phase than those with the OH terminals. Solution UV‐vis and photoluminescent (PL) spectra indicated that the linear and the HB polymers have analogous optical properties and display maximum absorbances and blue‐light emission on the basis of the PBT unit, where the Stokes shifts were observed because of intermolecular aggregation effects, but there is a large difference between the optical behaviors of the linear and the HB polymers in film, whose E_g values of the linear polymers decreased and those of the HB polymers vice versa. Quantum efficiencies (Φ) had a tendency of increase in the linear polymers and the HB polymers forming LC phases. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6688–6702, 2008     

Polyfluorene Polyelectrolyte Nanoparticles: Synthesis of Innovative Stabilizers for Heterophase Polymerization

Polyfluorene‐bearing bromohexyl side chains are quaternized by 1‐vinylimidazole in order to attach dialkylimidazolium bromide ionic liquid (IL) species along the conjugated backbone. Subsequently, polyfluorene polyelectrolyte nanoparticles (NPs) of 40 nm in average size are created via radical cross‐linking of the pendant vinylimidazolium groups. Anion exchange from Br⁻ to BF₄⁻, PF₆⁻, and bis(trifluoromethylsulfonyl)imide anion (TFSI⁻) renders NPs adjustable dispersability in various organic solvents. The hydrophobic‐conjugated backbone and the hydrophilic dialkylimidazolium bromide IL moieties depict an amphiphilic profile, which allows the NPs to be deployed as conductive stabilizer in the emulsion polymerization of styrene. The resultant latexes are fluorescent, tunable in size and can be transferred to organic solvents without forfeiting their colloidal stability.

     

Synthesis,Characterization, and thermoresponsive properties of Helical Polypeptides Derivatized from Poly(γ−4‐(3‐chloropropoxycarbonyl)benzyl‐L‐glutamate)

A series of side‐chain‐functionalized α‐helical polypeptides, i.e., poly(γ‐4‐(3‐chloropropoxycarbonyl)benzyl‐_L‐glutamate) (6) have been prepared from n‐butylamine initiated ring‐opening polymerization (ROP) of γ‐4‐(3‐chloropropoxycarbonyl)benzyl‐_L‐glutamic acid‐based N‐carboxyanhydride. Polypeptides bearing oligo‐ethylene‐glycol (OEG) groups or 1‐butylimidazolium salts were prepared from 6 via copper‐mediated [2+3] alkyne‐azide 1,3‐dipolar cycloaddition or nuleophilic substitution, respectively. CD and FTIR analysis revealed that the polymers adopt α‐helical conformations both in solution and the solid state. Polymers bearing OEG (m = 3) side‐chains showed reversible LCST‐type phase transition behaviors in water while polymers bearing 1‐butylimidazolium and I^? counter‐anions exhibited reversible UCST‐type transitions in water. Variable‐temperature UV‐vis analysis revealed that the phase transition temperatures (T_pts) were dependent on the main‐chain length and polymeric concentration. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2469–2480     

Electrochemical synthesis of PEDOT derivatives bearing imidazolium‐ionic liquid moieties

Novel poly(3,4‐ethylenedioxythiophene) (PEDOT) polymers bearing imidazolium‐ionic liquid moieties were synthesized by electrochemical polymerizations. For this purpose, new functional monomers were synthesized having an 3,4‐ethylenedioxythiophene (EDOT) unit and an imidazolium‐ionic liquid with different anions such as tetrafluoroborate (BF), bis(trifluoromethane)sulfonimide ((CF₃SO₂)₂N^?), and hexafluorophosphate (PF). Next, polymer films were obtained by electrochemical synthesis in dicholoromethane solutions. Obtained polymers were characterized, revealing the characteristics of PEDOT in terms of electrochemical and spectroelectrochemical properties, FTIR, ¹H NMR, and AFM microscopy. Interestingly, the hydrophobic character of electropolymerized films could be modified depending on the anion type. The hydrophobicity followed the trend PF > (CF₃SO₂)₂N^? > BF > pure PEDOT as determined by water contact angle measurements. Furthermore, the polymers could be dissolved in a range of polar organic solvents such as dimethylformamide, propylene carbonate, and dimethyl sulfoxide making these polymers interesting candidates for wet processing methods. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3010–3021, 2009     

Novel synthesis of N‐substituted polyacrylamides: Derivatization of poly(acrylic acid) with amines using a triazine‐based condensing reagent

Poly(acrylic acid) (PAA) was derivatized through the reaction of its pendant carboxylic acid (CO₂H) groups with a wide range of amine‐terminated molecules. These molecules contained alkyl, hydroxyl, sulfonic acid, or perfluoroalkyl groups. N‐substitution of PAA was carried out by the simple addition of 4‐(4,6‐dimethoxy‐1,3,5‐triazin‐2‐yl)‐4‐methylmorpholinium chloride (DMTMM), a triazine‐based condensing reagent, to a mixture of PAA and amine‐terminated molecules. From proton nuclear magnetic resonance and infrared spectroscopy, it was confirmed that these functional molecules were introduced into the PAA side chain via amide bonds. By the alteration of the synthetic conditions, functional side‐chain contents of greater than 95% were achieved for aqueous reactions with taurine, ethanol amine, and butyl amine. Side‐chain conversion was limited to ≤80% for reactions with perfluoroalkyl amines in methanol. Thus, DMTMM is an attractive replacement for carbodiimide condensing reagents such as 1,3‐dicyclohexylcarbodiimide and 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 126–136, 2006