Erratum: Thermal conductivity of thermoelectric Al‐substituted ZnO thin films

Due to a correction of the temperature oscillation, calculated by the 3ω voltage, the thermal conductivity of ZnO film is revised (κ = 8.8 ± 2.1 Wm^–1 K^–1). In particular, the Supporting Information is corrected. Furthermore, the thermoelectric figure‐of‐merit ZT of ZnO thin films is reduced by one half. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

不同退火温度下氧化锌薄膜可见发光与n型导电研究

采用脉冲激光沉积法在蓝宝石衬底上制备出可见光发光良好的氧化锌薄膜, 在不同的温度下进行了后退火处理. 随着退火温度的升高, 薄膜的可见光发光发生了显著改变, 载流子浓度、迁移率、电阻率也呈现出一定的变化规律. 结合 X射线衍射、扫描电子显微镜、光致发光谱及霍尔测量, 探讨了本征氧化锌薄膜可见光发光的发射机理, 并分析了其 n型导电的原因. 关键词： 氧化锌薄膜 可见光发光 n型导电     

Thermal conductivity of nanoscale polycrystalline ZnO thin films

Thermal conductivities (TCs) of ZnO thin films of thickness 80-276 nm prepared by sol-gel method are measured by the transient thermoreflectance (TTR) system. The obtained TCs ranging from 1.4 to 6.5 W/m K decrease while the thickness decrease. The measured TCs are much smaller than those of bulk ZnO, which is about 100 W/m K. The possible reasons for the decrease are the grain boundary and defects. The latter is the dominating one from the analysis.     

Enhanced photo-induced hydrophilicity of the sol-gel-derived ZnO thin films by Na-doping

Na-doped ZnO thin films with different Na/Zn ratio were prepared by sol-gel method. The microstructure, chemical composition, surface morphology, and wettability of the thin films were investigated by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy, and water contact angle apparatus. The relation of wettability and Na/Zn ratio has been studied in detail. The wetting behavior of the thin films can be reversibly switched from hydrophobic to hydrophilic, through alternation of UV illumination and dark storage (or thermal treatment). Photo-induced hydrophilicity of the thin films increases with increasing Na/Zn ratio up to 0.08 and then decreases. The mechanism can be attributed to surface nanostructure and the concentration of Na doping.     

Fe,Co共掺杂ZnO薄膜结构及发光特性研究

采用溶胶凝胶法在玻璃衬底上制备了Fe,Co共掺Zn0.9FexCo0.1-xO(x=0,0.03,0.05,0.07)系列薄膜.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子谱(XPS)和光致发光(PL)谱对薄膜样品的表面形貌、晶体结构、成分和光学性能进行了研究.XRD结果表明所有ZnO薄膜样品都呈六方纤锌矿结构,在样品中没有观察到与Fe和Co相关的团簇,氧化物及其他杂相的衍射峰,表明共掺杂改善了Fe或Co在ZnO的分散性.XPS测试结果揭示样品中Co离子的价态为+2价;Fe离子的价态为+2价和+3价共存,但Fe相对浓度的增大导致Fe3+含量增加.所有样品的室温光致发光谱(PL)均观察到紫外发光峰和蓝光双峰,其中Fe,Co共掺ZnO薄膜的紫外发光峰较本征ZnO出现蓝移,蓝光双峰峰位没有变化,但发光强度有所减弱;而掺杂ZnO薄膜的绿光发光峰几乎消失.最后,结合微结构和成分分析对薄膜样品的发光机理进行了讨论.     

Thermal stress induced band gap variation of ZnO thin films

The growth temperature and post annealing-dependent optical and structural effect of RF magnetron sputtered ZnO thin films were examined. As the growth temperature increased, the lattice constant increased and approached the bulk value, suggesting a decrease in interfacial strain between the substrate and thin film. For the post annealed samples, the interfacial strain decreased further and was close to the bulk value regardless of the post annealing environments (in air and O₂). The optical properties of all ZnO thin films examined and revealed higher transparency (>90%). Furthermore, the optical band gap varied according to the growth temperature and post annealing environments due to a decrease in the interfacial strain effect.     

Optical constants of Na-doped ZnO thin films by sol-gel method

The structural and optical properties of pure and Na-doped ZnO thin films have been investigated by X-ray diffraction (XRD), atom force microscopy and UV-Vis spectrophotometer. The crystal structure of all the thin films is the hexagonal wurtzite. The average grain size and surface roughness increases with the increase of the Na/Zn ratio. The optical band gap of the thin films decreases from 3.26 to 3.12 eV by increasing the Na/Zn ratio from 0.0 to 0.10. Transmittance spectra were used to determine the optical constants of the thin films, and the effect of Na/Zn ratio on the optical constants was investigated. With the increase of Na/Zn ratio, the refractive index decreases and the extinction coefficient increases in the 380-700 nm spectral range.     

Co,Sn共掺ZnO薄膜结构与光致发光的研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co,Sn掺杂ZnO系列薄膜.通过金相显微镜和X射线衍射(XRD)研究了Co与Sn掺杂对薄膜的表面形貌和微结构的影响.XRD结果表明,所有ZnO薄膜样品都存在(002)择优取向,特别Sn单掺ZnO薄膜的c轴择优取向最为显著,而且晶粒尺寸最大.XPS测试表明样品中Co和Sn的价态分别为2+和4+,证实Co²⁺,Sn⁴⁺进入了ZnO的晶格.室温光致发光谱(PL)显示在所有的样品中都有较强的蓝光双峰发射和较弱的绿光发 关键词： ZnO薄膜 溶胶-凝胶 掺杂 光致发光     

Engineering of electronic and optical properties of ZnO thin films via Cu doping

ZnO thin films doped with different Cu concentrations are fabricated by reactive magnetron sputtering technique. XRD analysis indicates that the crystal quality of the ZnO:Cu film can be enhanced by a moderate level of Cu-doping in the sputtering process. The results of XPS spectra of zinc, oxygen, and copper elements show that Cu-doping has an evident and complicated effect on the chemical state of oxygen, but little effect on those of zinc and copper. Interestingly, further investigation of the optical properties of ZnO:Cu samples shows that the transmittance spectra exhibit both red shift and blue shift with the increase of Cu doping, in contrast to the simple monotonic behavior of the Burstein–Moss effect. Analysis reveals that this is due to the competition between oxygen vacancies and intrinsic and surface states of oxygen in the sample. Our result may suggest an effective way of tuning the bandgap of ZnO samples.     

Co与Cu掺杂ZnO薄膜的制备与光致发光研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co, Cu单掺杂及Co,Cu共掺杂ZnO薄膜.用金相显微镜观察了Co与Cu掺杂对ZnO薄膜形貌的影响.X射线衍射（XRD）研究揭示所有ZnO薄膜样品都存在（002）择优取向,在Cu单掺的ZnO薄膜中晶粒尺寸最大.对所有样品的室温光致发光测量都观察到较强的蓝光双峰发射和较弱的绿光发射,其中长波长的蓝光峰和绿光峰都能够通过掺杂进行控制.对不同掺杂源的ZnO薄膜发光性能进行了分析,认为蓝光峰来源于电子由导带底到锌空位能级的跃迁及锌填隙到价带顶的跃迁,绿光峰是由于掺杂造成的 关键词： ZnO薄膜 溶胶-凝胶 Co Cu掺杂 光致发光     

Influence of polarity inversion on the electrical properties of Ga‐doped ZnO thin films

This study investigates how polarity inversion influences the relationship between the electrical properties of heavily Ga‐doped ZnO (GZO) films deposited by RF magnetron sputtering and their thickness. The electrical properties observed in very thin films are correlated with a change of polarity from O‐polar to Zn‐polar face upon increasing the film thickness based on results of valence band spectra measured by X‐ray photoelectron spectroscopy. It is found that the electrical properties of very thin GZO films deposited on Zn‐polar ZnO templates are significantly improved compared to those deposited on O‐polar face. A low resistivity of 2.62 × 10^–4 Ω cm, high Hall mobility of 26.9 cm²/V s, and high carrier concentration of 8.87 × 10²⁰ cm^–3 being achieved with 30 nm‐thick GZO films using Zn‐polar ZnO templates on a glass substrate. In contrast, the resistivity of 30 nm‐thick GZO films on bare glass that shows more likely O‐polar is very poor about 1.44 × 10^–3 Ω cm with mobility and carrier concentration are only 11.9 cm²/V s and 3.64 × 10²⁰ cm^–3, respectively. It is therefore proposed that polarity inversion plays an important role in determining the electrical properties of extremely thin GZO films. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

微量Mg掺杂ZnO薄膜的光致发光光谱和带隙变化机理研究

利用射频磁控溅射(RF-MS)法在450℃玻璃基底上制备了Mg掺杂量分别为0.81at%,2.43at%和4.05at%的ZnO薄膜,对其微观结构、室温光致发光光谱(PL)、光学和电学性质进行了研究.结果发现,微量Mg掺杂ZnO薄膜晶体具有六方纤锌矿结构并保持高结晶质量;掺杂0.81at%和2.43at%Mg的ZnO薄膜室温PL谱中近带边发射(NBE)峰的短波方向出现了高能发射带与NBE峰同时存在;随着Mg掺杂量增加至4.05at%,这个高能发射带逐步将NBE峰掩盖.推测在Mg掺杂ZnO薄膜中,Mg2+替代Zn2+附近核外电子的能量增大并产生了一个高能级.而未被Mg2+替代的Zn2+周围的核外电子能量状态不变,带间能级依然存在,随着Mg掺杂量的增加处于高能级的电子数目逐步增加并占绝对优势.因此,ZnO薄膜随着Mg掺杂量增加薄膜禁带宽度增大,这是由于Mg掺杂后周围电子能量增大与Burstein-Moss效应共同作用的结果.另外,薄膜在可见光区域的平均透射率均大于85%,随着Mg掺杂量的增加,薄膜禁带宽度增大并在3.36—3.52eV内变化;Mg掺杂量为0.81at%,2.43at%和4.05at%时,薄膜电阻率分别为2.2×10-3,3.4×10-3和8.1×10-3Ω.cm.     

Fe掺杂对溶胶凝胶法制备的ZnO: Ni薄膜结构及发光特性的影响

采用溶胶凝胶法在玻璃基片上制备了ZnO及Ni, Fe共掺杂的Zn_0.95-xNi_0.05Fe_xO (x=0, 0.005, 0.01, 0.03, 0.05) 薄膜. 通过扫描电镜(SEM) 和X射线衍射(XRD) 研究了薄膜样品的表面形貌和晶体结构. 结果表明所有样品都具有(002) 择优取向, Fe掺杂导致ZnO: Ni薄膜的晶体质量变差, 晶粒尺寸减小, 但适当的Fe掺杂有利于获得致密、 均匀的薄膜. XPS测试结果表明样品中Ni离子的价态为+2价, Fe离子的价态为+2价和+3价.室温光致发光(PL) 测量表明, 所有样品均观察到较强的紫外发光峰, 蓝光双峰和绿光发光峰. ZnO: Ni薄膜的发光强度可以通过Fe掺杂进行有效调节. 进而我们讨论了Ni, Fe共掺杂ZnO样品的发光机理.     

Effects of high-dose Ge ion implantation and post-implantation annealing on ZnO thin films

This paper reports that ion implantation to a dose of 1×10¹⁷ ions/cm² was performed on c-axis-orientated ZnO thin films deposited on (0001) sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600-900℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction (XRD), photoluminescence (PL). It was found that the intensities of (002) peak and near band edge (NBE) exitonic ultraviolet emission increased with increasing annealing temperature from 600-900℃. The defect related deep level emission (DLE) firstly increased with increasing annealing temperature from 600- 750℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at \sim 850℃ and \sim 750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900℃.     

The transparence comparison of Ga- and Al-doped ZnO thin films

The Ga-doped ZnO (GZO) and Al-doped ZnO (AZO) thin films were grown on quartz glass substrates by pulsed laser deposition under different oxygen partial pressures (PO₂). The transparent performances of films versus properties of structure and conductivity were discussed. With the increase of PO₂, the transmittance of both GZO films and AZO films increased to maximum and then decreased which were in according with the change of crystallization quality. The transmittance of GZO films was higher than that of AZO films, which were not dominated by the impurity ions induced by doping. AFM images and surface roughness mean square coefficients showed that the surfaces of GZO films were smoother than that of AZO films, which were due to the dopant Ga acting as the surfactant and smoothed the GZO films surface.     

退火对ZnO:Al薄膜光致发光性能的影响

 采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜,通过不同温度的退火处理,研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向,随着退火温度的升高,(002)峰的强度逐渐增强,同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后,以500 nm为中心的绿带发射逐渐减弱,而带边发射强度有所增强,并且逐渐红移到366 nm附近,与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明,AZO薄膜的发光特性与退火时间也有很大关系,时间过短可见波段的发射较强,但时间过长会使晶粒发生团聚,导致紫外发射峰强度减弱。     

Ordered ultra thin ZnO films on metal substrate

Ultra thin ZnO films were prepared on metal Mo(1 1 0) substrate under ultrahigh vacuum conditions either by depositing Zn in 10⁻⁵ Pa oxygen or by oxidizing pre-deposited Zn films. The films were characterized in situ by various surface analytical techniques, including Auger electron spectroscopy, X-ray and ultraviolet photoelectron spectroscopies, low energy electron diffraction and high resolution electron energy loss spectroscopy. The results indicate that a long-range ordered and stoichiometric ZnO films are formed along its [0 0 0 1] direction. The annealing experiments show that as-prepared ZnO films are thermal stable until 800 K. This study provides constructive information to further understand the growth mechanism of ZnO films on different substrates.     

Al/ZnO/Al薄膜的结构与磁性分析

采用直流磁控溅射的方法制备了Al/ZnO/Al纳米薄膜,并对薄膜分别在真空及空气中进行退火处理.利用X射线衍射仪(XRD)和物理性能测量仪(PPMS)分别对薄膜样品的结构和磁性进行了表征.XRD分析表明,不同的退火氛围对薄膜的微结构有着很大的影响.采用了一种新的修正方法对磁测量结果进行修正,计算了基底拟合误差的最大值,并对修正后样品的磁性进行了分析.结果显示,室温铁磁性可能与Al和ZnO基体之间发生的电荷转移以及在不同退火氛围下Al在ZnO晶格中的地位变化有关. 关键词： Al/ZnO/Al薄膜 铁磁性 磁性表征     

Synthesis and thermoelectric properties of Bi-doped SnSe thin films

Bi doped n-type SnSe thin films were prepared by chemical vapor deposition (CVD) and their structure and thermoelectric properties were studied. The x-ray diffraction patterns, x-ray photoelectron spectroscopy, and microscopic images show that the prepared SnSe thin films were composed of pure SnSe crystals. The Seebeck coefficients of the Bi-doped SnSe were greatly improved compared to that of undoped SnSe thin films. Specifically, Sn_0.99Bi_0.01Se thin film exhibited a Seebeck coefficient of -905.8μV·K^-1 at 600 K, much higher than 285.5 μV·K^-1 of undoped SnSe thin film. Further first-principles calculations reveal that the enhancement of the thermoelectric properties can be explained mainly by the Fermi level lifting and the carrier pockets increasing near the Fermi level due to Bi doping in the SnSe samples. Our results suggest the potentials of the Bi-doped SnSe thin films in thermoelectric applications.