Synthesis and properties of O‐2‐[2‐(2‐methoxyethoxy)ethoxy]acetyl cellulose

In this article, a series of O‐2‐[2‐(2‐methoxyethoxy)ethoxy]acetyl celluloses with different degree of substitution (DS) values was synthesized by a homogeneous reaction of cellulose with 2‐[2‐(2‐methoxyethoxy)ethoxy]acetyl chloride in a 10% (w/w) dimethylacetamide/lithium chloride solution, combined with pyridine as the acid acceptor. The total DS values of the derivatives in anhydroglucose units was determined by ¹H and ¹³C NMR spectra, and ranged from 0.4 to 3.0, depending on the amount of acid chloride in the reaction. The effects of the total DS values and the O‐2‐[2‐(2‐methoxyethoxy)ethoxy]acetyl substituent distribution on the solubility of the derivatives were investigated. The lowest limit of the DS value for water‐soluble O‐2‐[2‐(2‐methoxyethoxy)ethoxy]acetyl cellulose was approximately 0.5, which is lower than that of methylcellulose. The amphiphilic derivatives with higher DS values than 1.7 exhibited a good solubility in both water and organic solvents, such as dimethyl sulfoxide, tetrahydrofuran, and chloroform. Sol‐gel transition in aqueous solution was observed for the amphiphilic derivatives with a higher DS value than 1.7; the precipitation temperature (T_p) decreased as the DS value increased, showing that the derivatives are highly temperature sensitive. The thermal properties of the fully substituted derivative were measured using polarized microscopy, DSC, and X‐ray diffraction; and are discussed in terms of phase transition of the sample derivatives. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 376–382, 2001     

Effect of catalyst systems and reaction conditions on the synthesis of cellulose‐g‐PDMAam copolymers by controlled radical polymerization

Various copper‐based catalyst systems and reaction conditions were studied in the graft copolymerization of N,N‐dimethylacrylamide (DMAam) with a cellulose‐based macroinitiator by controlled radical polymerization. The cellulose macroinitiator with degree of substitution DS = 0.44 was synthesized from dissolving softwood pulp in a LiCl/DMAc solution. The graft copolymerizations of DMAam, using the cellulose macroinitiator and various copper‐based catalyst systems, were then carried out in DMSO solutions. The copolymerization kinetics was followed by ¹H NMR. Water‐soluble cellulose‐g‐PDMAam copolymers were comprehensively characterized by ATR‐FTIR and ¹H NMR spectroscopies and SEC analyses. DLS and steady‐shear viscosity measurements revealed that when the DP_graft of the cellulose‐g‐PDMAam copolymer is high enough, the copolymer forms a more compact structure in water. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Three‐arm star block copolymers of ε‐caprolactone and acrylic acid: Synthesis and micellization behavior

A series of well‐defined three‐arm star poly(ε‐caprolactone)‐b‐poly(acrylic acid) copolymers having different block lengths were synthesized via the combination of ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP). First, three‐arm star poly(ε‐caprolactone) (PCL) (M_n = 2490–7830 g mol^?1; M_w/M_n = 1.19–1.24) were synthesized via ROP of ε‐caprolactone (ε‐CL) using tris(2‐hydroxyethyl)cynuric acid as three‐arm initiator and stannous octoate (Sn(Oct)₂) as a catalyst. Subsequently, the three‐arm macroinitiator transformed from such PCL in high conversion initiated ATRPs of tert‐butyl acrylate (^tBuA) to construct three‐arm star PCL‐b‐P^tBuA copolymers (M_n = 10,900–19,570 g mol^?1; M_w/M_n = 1.14–1.23). Finally, the three‐arm star PCL‐b‐PAA copolymer was obtained via the hydrolysis of the PtBuA segment in three‐arm star PCL‐b‐P^tBuA copolymers. The chain structures of all the polymers were characterized by gel permeation chromatography, proton nuclear magnetic resonance (¹H NMR), and Fourier transform infrared spectroscopy. The aggregates of three‐arm star PCL‐b‐PAA copolymer were studied by the determination of critical micelles concentration and transmission electron microscope. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Efficient Homogeneous Chemical Modification of Bacterial Cellulose in the Ionic Liquid 1‐N‐Butyl‐3‐methylimidazolium Chloride

Summary: Bacterial cellulose (BC), a unique type of cellulose, with high degree of polymerization of 6 500 could be dissolved easily in the ionic liquid 1‐N‐butyl‐3‐methylimidazolium chloride. For the first time, well‐soluble BC acetates and carbanilates of high degree of substitution (up to a complete modification of all hydroxyl groups) were accessible under homogeneous and mild reaction conditions. Characterization of the new BC derivatives by NMR and FTIR spectroscopy shows an unexpected distribution of the acetyl moieties in the order O‐6 > O‐3 > O‐2.

¹³C NMR spectrum (DMSO‐d₆) of a cellulose acetate with a DS of 2.25 synthesized in 1‐N‐butyl‐3‐methylimidazolium chloride.     

Core‐shell nanoparticles with hyperbranched poly(arylene‐oxindole) interiors

Core‐shell type star polymers composed of poly(tert‐butyl acrylate) (poly(t‐BuA)) arms and 100% hyperbranched poly(arylene‐oxindole) interiors were synthesized via the “core‐first” method. Atom transfer radical polymerization of t‐BuA initiated by 2‐bromopropionyl terminal groups of the hyperbranched core was applied for the synthesis of the stars. The resultant star structures were characterized by gel permeation chromatography with triple detection. Polymers of molar masses M_n up to 1.68 × 10⁵ g/mol were obtained. The obtained star polymers compared with the linear counterparts of the same molar mass have a much more compact structure in solution. The intrinsic viscosities of the stars are also significantly lower than their linear counterparts. Light scattering experiments were performed to provide information about the size of these macromolecules in solution. Preliminary characterization of the thermal properties of these novel materials is also reported. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1120–1135, 2009     

New associative EHEC‐g‐PAam copolymers: Their syntheses,characterization, and rheological behavior

The syntheses and rheological behavior of ethyl hydroxyethyl cellulose (EHEC)‐based graft‐copolymers were studied. Copolymers were prepared by grafting EHEC with acrylamide (Aam) via reversible addition fragmentation chain transfer (RAFT) polymerization. Hydroxyl groups of EHEC were esterified with a carboxylic acid functional chain transfer agent (CTA) to prepare EHEC‐macroCTAs with different degrees of substitution. EHEC‐macroCTAs were characterized by ATR‐FTIR, ¹³C NMR, and SEC, and elemental analysis was used to quantify the degree of CTA substitution. EHEC‐macroCTAs with different degrees of substitution were copolymerized with acrylamide by “grafting from” technique. Formation of new cellulose‐based copolymers was comprehensively confirmed by ¹H NMR, ATR‐FTIR, and SEC measurements. Further, the associations of EHEC‐g‐PAam copolymers in water were studied at various concentrations and temperatures by means of UV–vis spectroscopy, fluorescence spectroscopy, and rheological measurements. The results indicate that copolymers have both intra and intermolecular association in water depending on the amount of grafts. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1869–1879, 2009     

Synthesis and characterizations of the four‐armed amphiphilic block copolymer S[poly(2,3‐dihydroxypropyl acrylate)‐block‐poly(methyl acrylate)]4

The polymers poly[(2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate] (PDMDMA) and four‐armed PDMDMA with well‐defined structures were prepared by the polymerization of (2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate (DMDMA) in the presence of an atom transfer radical polymerization (ATRP) initiator system. The successive hydrolyses of the polymers obtained produced the corresponding water‐soluble polymers poly(2,3‐dihydroxypropyl acrylate) (PDHPA) and four‐armed PDHPA. The controllable features for the ATRP of DMDMA were studied with kinetic measurements, gel permeation chromatography (GPC), and NMR data. With the macroinitiators PDMDMA–Br and four‐armed PDMDMA–Br in combination with CuBr and 2,2′‐bipyridine, the block polymerizations of methyl acrylate (MA) with PDMDMA were carried out to afford the AB diblock copolymer PDMDMA‐b‐MA and the four‐armed block copolymer S{poly[(2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate]‐block‐poly(methyl acrylate)}₄, respectively. The block copolymers were hydrolyzed in an acidic aqueous solution, and the amphiphilic diblock and four‐armed block copolymers poly(2,3‐dihydroxypropyl acrylate)‐block‐poly(methyl acrylate) were prepared successfully. The structures of these block copolymers were verified with NMR and GPC measurements. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3062–3072, 2001     

In situ polymerization and morphology of polypyrrole obtained in water‐soluble polymer templates

Several water‐soluble polymers were used as templates for the in situ polymerization of pyrrole to determine their effect on the generation of nanosized polypyrrole (PPy) particles. The polymers used include: polyvinyl alcohol (PVA), polyethylene oxide (PEO), poly(vinyl butyral), polystyrene sulfonic acid, poly(ethylene‐alt‐maleic anhydride) (PEMA), poly(octadecene‐alt‐maleic anhydride), poly(N‐vinyl pyrrolidone), poly(vinyl butyral‐co‐vinyl alcohol‐co‐vinyl acetate), poly(N‐isopropyl acrylamide), poly(ethylene oxide‐block‐propylene oxide), hydroxypropyl methyl cellulose, and guar gum. The oxidative polymerization of pyrrole was carried out with FeCl₃ as an oxidant. The morphology of PPy particles obtained after drying the resulting aqueous dispersions was examined by optical microscopy, and selected samples were further analyzed via atomic force microscopy. Among the template polymers, PVA was the most efficient in generating stable dispersions of PPy nanospheres in water, followed by PEO and PEMA. The average size of PPy nanospheres was in the range of 160 nm and found to depend on the molecular weight and concentration of PVA. Model reactions and kinetics of the polymerization reaction of pyrrole in PVA were carried out by hydrogen ¹H NMR spectroscopy using ammonium persulfate as an oxidant. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and NMR characterization of 6‐Phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose

Cellulose ( 1 ) was converted for the first time to 6‐phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 6 ) in 33% overall yield. Intermediates in the five‐step conversion of 1 to­ 6 were: 6‐O‐tritylcellulose ( 2 ), 6‐O‐trityl‐2,3‐di‐O‐methylcellulose ( 3 ), 2,3‐di‐O‐methylcellulose ( 4 ); and 6‐bromo‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 5 ). Elemental and quantitative carbon‐13 analyses were concurrently used to verify and confirm the degrees of substitution in each new polymer. Gel permeation chromotography (GPC) data were generated to monitor the changes in molecular weight (DP_w) as the synthesis progressed, and the compound average decrease in cellulose DP_w was ～ 27%. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to characterize the decomposition of all polymers. The degradation temperatures ( °C) and percent char at 500 °C of cellulose derivatives 2 to 6 were 308.6 and 6.3%, 227.6 °C and 9.7%, 273.9 °C and 30.2%, 200.4 °C and 25.6%, and 207.2 °C and 27.0%, respectively. The glass transition temperature (T_g) of­6‐O‐tritylcellulose by dynamic mechanical analysis (DMA) occurred at 126.7 °C and the modulus (E′, Pa) dropped 8.9 fold in the transition from ?150 °C to + 180 °C (6.6 × 10⁹ to 7.4 × 10⁸ Pa). Modulus at 20 °C was 3.26 × 10⁹ Pa. Complete proton and carbon‐13 chemical shift assignments of the repeating unit of the title polymer were made by a combination of the HMQC and COSY NMR methods. Ultimate non‐destructive proof of carbon–carbon bond formation at C6 of the anhydroglucose moiety was established by generating correlations between resonances of CH₂6 (anhydroglucose) and C1′, H2′, and H6′ of the attached aryl ring using the heteronuclear multiple‐bond correlation (HMBC) method. In this study, we achieved three major objectives: (a) new methodologies for the chemical modification of cellulose were developed; (b) new cellulose derivatives were designed, prepared and characterized; (c) unequivocal structural proof for carbon–carbon bond formation with cellulose was derived non‐destructively by use of one‐ and two‐dimensional NMR methods. Copyright © 2002 John Wiley & Sons, Ltd.     

“Smart” poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) copolymers synthesized by nitroxide mediated radical polymerization

A series of poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(DMAEMA‐ran‐VBK)) random copolymers, with VBK molar feed compositions f_VBK,0 = 0.02–0.09, were synthesized using 10 mol % [tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] nitroxide (SG1) relative to 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropionic acid (BlocBuilder) at 80 °C and 90 °C. Controlled polymerizations were observed, even with f_VBK,0 = 0.02, as reflected by a linear increase in number average molecular weight (M_n) versus conversion X ≤ 0.6 with final copolymers characterized by relatively narrow, monomodal molecular weight distributions (M_w/M_n ≈ 1.5). Poly(DMAEMA‐ran‐VBK) copolymers were deemed sufficiently pseudo‐“living” to reinitiate a second batch of N,N‐dimethylacrylamide (DMAA), with very few apparent dead chains, as indicated by the monomodal shift in the gel permeation chromatography chromatograms. Poly(DMAEMA‐ran‐VBK) random copolymers exhibited tuneable lower critical solution temperature (LCST), in aqueous solution, by modifying copolymer composition, solution pH and by the addition of the water‐soluble poly(DMAA) segment. ¹H NMR analysis determined that, in water, the VBK units of the poly(DMAEMA‐ran‐VBK) random copolymer were segregated to the interior of the copolymer aggregate regardless of solution temperature and that poly(DMAEMA‐ran‐VBK)‐b‐poly(DMAA) block copolymers formed micelles above the LCST. In addition, the final random copolymer and block copolymer exhibited temperature dependent fluorescence due to the VBK units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Amphiphilic conetworks. III. Poly(2,3‐dihydroxypropyl methacrylate)–polyisobutylene and poly(ethylene glycol) methacrylate–polyisobutylene based hydrogels prepared by two‐step polymer procedure

This article describes the synthesis and characterization of new amphiphilic polymer conetworks containing hydrophilic poly(2,3‐dihydroxypropyl methacrylate) or poly(ethylene glycol) methacrylate (PEGMA) and hydrophobic polyisobutylene chains. This conetworks were prepared by a two‐step polymer synthesis. In the first step, a cationic copolymer of isobutylene and 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate (IDI) was prepared. The isocyanate groups of the IB‐IDI random copolymer were subsequently transformed in situ to methacrylate (MA) groups in reaction with 2‐hydroxyethyl methacrylate (HEMA). In the second step, the resulting MA‐multifunctional PIB‐based crosslinker, PIB(MA)_n, with an average functionality of approximately four per chain, was copolymerized with 2,3‐dihydroxypropyl methacrylate or poly(ethylene glycol) methacrylate by radical mechanism in tetrahydrofuran giving rise to amphiphilic conetworks containing 11–60 mol % of DHPMA or 10–12 mol % of PEGMA. The synthesized conetworks were characterized with solid‐state ¹³C‐NMR spectroscopy and differential scanning calorimetry. The amphiphilic nature of the conetworks was proved by swelling in both water and n‐heptane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4074–4081, 2007     

Synthesis,characterization, and micellization of PCL‐g‐PEG copolymers by combination of ROP and “Click” chemistry via “Graft onto” method

Biodegradable and biocompatible PCL‐g‐PEG amphiphilic graft copolymers were prepared by combination of ROP and “click” chemistry via “graft onto” method under mild conditions. First, chloro‐functionalized poly(ε‐caprolactone) (PCL‐Cl) was synthesized by the ring‐opening copolymerization of ε‐caprolactone (CL) and α‐chloro‐ε‐caprolactone (CCL) employing scandium triflate as high‐efficient catalyst with near 100% monomer conversion. Second, the chloro groups of PCL‐Cl were quantitatively converted into azide form by NaN₃. Finally, copper(I)‐catalyzed cycloaddition reaction was carried out between azide‐functionalized PCL (PCL‐N₃) and alkyne‐terminated poly(ethylene glycol) (A‐PEG) to give PCL‐g‐PEG amphiphilic graft copolymers. The composition and the graft architecture of the copolymers were characterized by ¹H NMR, FTIR, and GPC analyses. These amphiphilic graft copolymers could self‐assemble into sphere‐like aggregates in aqueous solution with diverse diameters, which decreased with the increasing of grafting density. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of “Living” star‐shaped poly(N‐vinylcaprolactam) with four arms and carboxylic acid end groups

Poly(N‐vinylcaprolactam) (PNVCL) star‐shaped polymers with four arms and carboxyl end groups were synthesized by reversible addition–fragmentation chain transfer (RAFT) polymerization of N‐vinylcaprolactam (NVCL) employing a tetrafunctional trithiocarbonate as an R‐RAFT agent. The resulting star polymers were characterized using ¹H NMR, FT‐IR, gel permeation chromatography (GPC), and UV–vis. Molecular weight of star polymers were analyzed by GPC and UV–vis being observed that the values obtained were very similar. Furthermore, the thermosensitive behavior of the star polymers was studied in aqueous solution by measuring the lower critical solution temperature by dynamic light scattering. Star‐shaped PNVCL were chain extended with ethyl‐hexyl acrylate (EHA) to yield star PNVCL‐b‐PEHA copolymers with an EHA molar content between 4% and 6% proving the living character of the star‐shaped macroCTA. These star block copolymers form aggregates in aqueous solutions with a hydrodynamic diameter ranged from 170 to 225 nm. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2156–2165     

Dilute solution properties of cellulose in LiOH/urea aqueous system

Cellulose was dissolved rapidly in 4.6 wt % LiOH/15 wt % urea aqueous solution and precooled to –10 °C to create a colorless transparent solution. ¹³C‐NMR spectrum proved that it is a direct solvent for cellulose rather than a derivative aqueous solution system. The result from transmission electron microscope showed a good dispersion of the cellulose molecules in the dilute solution at molecular level. Weight‐average molecular weight (M_w), root mean square radius of gyration (〈s²〉_z^1/2), and intrinsic viscosity ([η]) of cellulose in LiOH/urea aqueous solution were examined with laser light scattering and viscometry. The Mark–Houwink equation for cellulose in 4.6 wt % LiOH/15 wt % urea aqueous solution was established to be [η] = 3.72 × 10^?2 M in the M_w region from 2.7 × 10⁴ to 4.12 × 10⁵. The persistence length (q), molar mass per unit contour length (M_L), and characteristic ratio (C_∞) of cellulose in the dilute solution were given as 6.1 nm, 358 nm^?1, and 20.8, respectively. The experimental data of the molecular parameters of cellulose agreed with the Yamakawa–Fujii theory of the worm‐like chain, indicating that the LiOH/urea aqueous solution was a desirable solvent system of cellulose. The results revealed that the cellulose exists as semistiff‐chains in the LiOH/urea aqueous solution. The cellulose solution was stable during measurement and storage stage. This work provided a new colorless, easy‐to‐prepare, and nontoxic solvent system that can be used with facilities to investigate the chain conformation and molecular weight of cellulose. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3093–3101, 2006     

Controlled grafting of cellulose esters using SET‐LRP process

Here, we present the first example of application of single‐electron transfer living radical polymerization (SET‐LRP) process to a controlled grafting of cellulose esters, cellulose diacetate (CDA), and cellulose acetate butyrate (CAB). The cellulose ester macroinitiators with various functionality densities have been prepared by acylation of the backbones with 2‐bromoisobutyryl (BrIB) and dichloroacetyl (DCA) groups, respectively. Methacrylate monomers were polymerized using DCA‐functionalized macroinitiators in the presence of pentamethyldiethylene triamine as a ligand. At 30 °C, the reaction is rather slow, reaching about 10% conversion after 3 to 6 h of polymerization, whereas the higher temperature (60 °C) perceptibly speeds up the polymerization so that methyl methacrylate (MMA) conversion is ～30% after 5 h. Graft copolymers with random‐type and diblock‐type grafts having amphiphilic character were also synthesized. For acrylate grafting (BuA and t‐BuA), BrIB‐functionalized macroinitiators are more convenient in a combination with a low concentration of Cu(0) and Me₆TREN as a ligand and polymerization is detectably faster even at the lower temperature than that of MMA. Kinetic studies show “living” character of both the graftings. Important advantages of SET‐LRP, compared with classic ATRP, are (i) higher polymerization rate, (ii) lower extent of recombination of the growing grafts and (iii) negligible coloration of the products with catalytic residua, so that the prepared polymers do not require additional careful purification. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Well‐defined amphiphilic polymethylene‐b‐poly(acrylic acid) diblock copolymers: New synthetic strategy and their self‐assembly

Well‐defined amphiphilic polymethylene‐b‐poly (acrylicacid) diblock copolymers have been synthesized via a new strategy combining polyhomologation and atom transfer radical polymerization (ATRP). Hydroxyl‐terminated polymethylenes (PM‐OH) with different molecular weights and narrow molecular weight distribution are obtained through the polyhomologation of dimethylsulfoxonium methylides following quantitative oxidation via trimethylamine‐N‐oxide dihydrate. Subsequently, polymethylene‐based macroinitiators (PM‐MIs M_n = 1,300 g mol^?1 [M_w/M_n = 1.11] and M_n = 3,300 g mol^?1 [M_w/M_n = 1.04]) are synthesized by transformation of terminal hydroxyl group of PM‐OH to α‐haloester in ～100% conversion. ATRPs of tert‐butyl acrylate (t‐BuA) are then carried out using PM‐MIs as initiator to construct PM‐b‐P(t‐BuA) diblock copolymers with controllable molecular weight (M_n = 8,800–15,800 g mol^?1 M_w/M_n = 1.04–1.09) and different weight ratio of PM/P(t‐BuA) segment (1:1.7–1:11.2). The amphiphilic PM‐b‐PAA diblock copolymers are finally prepared by hydrolysis of PM‐b‐P(t‐BuA) copolymers and their self‐assembly behavior in water is preliminarily investigated via the determination of critical micelle concentrations, dynamic light scattering, and transmission electron microscope (TEM). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline)‐block‐poly(ε‐caprolactone) copolymers

A series of novel types of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline)‐block‐poly(ε‐caprolactone) (PHpr‐b‐PCL) copolymers were successfully synthesized via melt block copolymerization of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) and ε‐caprolactone (ε‐CL) with a trifunctional initiator trimethylolpropane (TMP) and stannous octoate (SnOct₂) as a catalyst. For the homopolycondensation of N‐CBz‐Hpr with TMP initiator and SnOct₂ catalyst, the number‐average molecular weight (M_n) of prepolymer increases from 530 to 3540 g mol^?1 with the molar ratio of monomer to initiator (3–30), and the molecular weight distribution (M_w/M_n) is between 1.25 to 1.32. These three‐armed prepolymer PHpr were subsequently block copolymerized with ε‐caprolactone (ε‐CL) in the presence of SnOct₂ as a catalyst. The M_n of the copolymer increased from 2240 to 18,840 g mol^?1 with the molar ratio (0–60) of ε‐CL to PHpr. These products were characterized by differential scanning calorimetry (DSC), ¹H NMR, and gel permeation chromatography. According to DSC, the glass‐transition temperature (T_g) of the three‐armed polymers depended on the molar ratio of monomer/initiator that were added. In vitro degradation of these copolymers was evaluated from weight‐loss measurements and the change of M_n and M_w/M_n. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1708–1717, 2005     

Synthesis and enzymatic degradation of 2‐methylene‐1,3‐dioxepane and methyl acrylate copolymers

Copolymers of 2‐methylene‐1,3‐dioxepane (MDO) and methyl acrylate (MA) containing ester units both in the backbone and as pendant groups were synthesized by free‐radical copolymerization. The influence of reaction conditions such as the polymerization time, temperature, initiator concentration, and comonomer feed ratio on the yield, molecular weight, and copolymer composition was investigated. The structure of the copolymers was confirmed by ¹H NMR, ¹³C NMR, and IR spectroscopy. Differential scanning calorimetry indicated that the copolymers had a random structure. An NMR study showed that hydrogen transfer occurred during the copolymerization. The reactivity ratios of the comonomers were r_MDO = 0.0235 and r_MA = 26.535. The enzymatic degradation of the copolymers obtained was carried out in the presence of proteinase K or a crude enzyme extracted from earthworms. The experimental results showed that the higher ester molar percentage in the backbone caused a faster degradation rate. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2898–2904, 2003     

Universal xanthate‐mediated controlled free radical polymerizations of the “less activated” vinyl monomers

The living free radical polymerizations of three “less activated” monomers (LAMs), vinyl acetate, N‐vinylcarbazole, and N‐vinylpyrrolidone, were successfully achieved in the presence of a disulfide, isopropylxanthic disulfide (DIP), using 2,2′‐azoisobutyronitrile (AIBN) as the initiator. The living behaviors of polymerizations of LAMs are evidenced by first‐order kinetic plots and linear increase of molecular weights (M_ns) of the polymers with monomer conversions, while keeping the relatively low molecular weight distributions, respectively. The effects of reaction temperatures and molar ratios of components on the polymerization were also investigated in detail. The polymerization proceeded with macromolecular design via interchange of xanthate process, where xanthate formed in situ from reaction of AIBN and DIP. The architectures of the polymers obtained were characterized by GPC, ¹H NMR, UV–vis, and MALDI‐TOF‐MS spectra, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Acylation of Cellulose with N,N′‐Carbonyldiimidazole‐Activated Acids in the Novel Solvent Dimethyl Sulfoxide/Tetrabutylammonium Fluoride

Summary: Carboxylic acids were efficiently activated with N,N′‐carbonyldiimidazole (CDI) and applied for the acylation of cellulose under homogeneous conditions using dimethyl sulfoxide (DMSO)/tetrabutylammonium fluoride trihydrate (TBAF) as solvent. The simple and elegant method is a very mild and easily applicable tool for the synthesis of pure aliphatic, alicyclic, bulky, and unsaturated cellulose esters with degrees of substitution of up to 1.9. Products are soluble in organic solvents, e.g., DMSO or N,N‐dimethylformamide (DMF). The cellulose esters were characterized by elemental analysis, FT‐IR, ¹H and ¹³C NMR spectroscopy and show no impurities or substructures resulting from side reactions.

The esterification of cellulose using carboxylic acids activated in situ with N,N′‐carbonyldiimidazole.