Micellar polymerization of amphiphilic poly(vinyl alcohol) macromonomer having a methacrylate end group prepared by aldol‐type group‐transfer polymerization

Amphiphilic and heterotactic‐rich poly(vinyl alcohol) (PVA) macromonomer, that is, PVA having a phenyl or phenoxyethyl methacrylate unit as the polymerizable end group, was synthesized via the aldol‐type group‐transfer polymerization (aldol‐GTP) technique. Aldol‐GTPs of vinyloxytriethylsilane (VOTES) were carried out in dichloromethane with 4‐methacryloylbenzaldehyde and 4‐(2‐methacryloylethoxy)benzaldehyde as the initiators with various Lewis acids. The polymerizations proceeded smoothly to give silylated PVA macromonomers (number‐average molecular weights: 1.3 × 10³–1.96 × 10⁴). Poly(VOTES) was easily desilylated to give heterotactic‐rich PVA macromonomer in good yield. The critical micelle concentration of the PVA macromonomer was determined by surface‐tension measurement. Micellar polymerization of the amphiphilic macromonomer gave comb‐shaped (graft) polymer having PVA side chains effectively (conversion: 80–82%), whereas polymerization in dimethyl sulfoxide (homogeneous state) did not. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4477–4484, 2002     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008     

Synthesis and self‐assembly of well‐defined cyclodextrin‐centered amphiphilic A14B7 multimiktoarm star copolymers based on poly(ε‐caprolactone) and poly(acrylic acid)

Novel amphiphilic A₁₄B₇ multimiktoarm star copolymers composed of 14 poly(ε‐caprolactone) (PCL) arms and 7 poly(acrylic acid) (PAA) arms with β‐cyclodextrin (β‐CD) as core moiety were synthesized by the combination of controlled ring‐opening polymerization (CROP) and atom transfer radical polymerization (ATRP). 14‐Arm star PCL homopolymers (CDSi‐SPCL) were first synthesized by the CROP of CL using per‐6‐(tert‐butyldimethylsilyl)‐β‐CD as the multifunctional initiator in the presence of Sn(Oct)₂ at 125 °C. Subsequently, the hydroxyl end groups of CDSi‐SPCL were blocked by acetyl chloride. After desilylation of the tert‐butyldimethylsilyl ether groups from the β‐CD core, 7 ATRP initiating sites were introduced by treating with 2‐bromoisobutyryl bromide, which further initiated ATRP of tert‐butyl acrylate (tBA) to prepare well‐defined A₁₄B₇ multimiktoarm star copolymers [CDS(PCL‐PtBA)]. Their molecular structures and physical properties were in detail characterized by ¹H NMR, SEC‐MALLS, and DSC. The selective hydrolysis of tert‐butyl ester groups of the PtBA block gave the amphiphilic A₁₄B₇ multimiktoarm star copolymers [CDS(PCL‐PAA)]. These amphiphilic copolymers could self‐assemble into multimorphological aggregates in aqueous solution, which were characterized by dynamic light scattering (DLS), transmission electron microscopy (TEM) and atomic force microscopy (AFM). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2961–2974, 2010     

Controlled synthesis of pH‐responsive amphiphilic A2B2 miktoarm star block copolymer by combination of SET‐LRP and RAFT polymerization

The pH‐responsive amphiphilic A₂B₂ miktoarm star block copolymer, poly(acrylic acid)₂‐poly(vinyl acetate)₂ [(PAA)₂(PVAc)₂], with controlled molecular weight and well‐defined structure was successfully synthesized via combination of single‐electron transfer‐mediated living radical polymerization (SET‐LRP) and reversible addition‐fragmentation chain transfer (RAFT) polymerization methods. First, the precursor two‐armed poly(t‐butyl acrylate) (PtBA)₂ functionalized with two xanthate groups was prepared by SET‐LRP of t‐butyl acrylate in acetone at 25 °C using the novel tetrafunctional bromoxanthate (Xanthate₂‐Br₂) as an Iniferter (initiator‐transfer agent‐terminator) agent. The polymerization behavior showed typical LRP natures by the first‐order polymerization kinetics and the linear dependence of molecular weight of the polymer on the monomer conversion. Second, the A₂B₂ miktoarm star block copolymer (PtBA)₂(PVAc)₂ was prepared by RAFT polymerization of VAc using (PtBA‐N₃)₂(Xanthate)₂ obtained as the macro‐RAFT agent. Finally, the pH‐sensitive A₂B₂ amphiphilic miktoarm star block copolymer poly(acrylic acid)₂‐poly(vinyl acetate)₂ ((PAA)₂(PVAc)₂) was obtained by selectively cleavage of t‐butyl esters of (PtBA)₂(PVAc)₂. All the miktoarm star block copolymers were characterized by GPC, ¹H‐NMR, and FT‐IR spectra. The self‐assembly behaviors of the amphiphilic A₂B₂ miktoarm block copolymers (PAA)₂(PVAc)₂ were also investigated by transmission electron microscopy. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Synthesis of poly(vinyl laurate)‐b‐poly(vinyl stearate) diblock copolymers by cobalt‐mediated radical polymerization in solution

Poly(vinyl laurate) (PVL) and poly(vinyl stearate) (PVS) were synthesized by means of cobalt‐mediated radical polymerization (CMRP). Cobalt(II) diacetylacetonate (Co(acac)₂) was demonstrated to control the radical polymerization of these monomers in solution. Molecular weights up to 15,000 g·mol^?1 were obtained with reasonably low polydispersity indices (PDI < 1.3). The efficiency of the redox initiator [lauroyle peroxide (LPO)/citric acid (CA)] was found to be low (around 10%) as already reported for vinyl acetate. The solvent and temperature were found to have a very weak influence on the initiator efficiency. It appeared that CA played no role in the initiation process that only involved a redox reaction between LPO and Co(acac)₂. PVL‐b‐PVS diblock copolymers could be synthesized using two strategies: (1) Sequential addition, that is, addition of the second monomer (VS) at high conversion of the first one (VL). (2) Macroinitiator technique, that is, isolation of a PVL macroinitiator then polymerization of VS from this cobalt functionalized macroinitiator. Both techniques allowed the synthesis of diblock copolymers with molar masses around 25,000 g·mol^?1 and PDI lower than 1.4. The resulting materials were characterized by DSC, revealing that both blocks exhibit side‐chain crystallinity and phase segregate in the bulk. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Selective single monomer addition in living cationic polymerization: Sequential double end‐functionalization in combination with capping agent

Amine‐functionalized and amine‐carboxylate double‐functionalized polymers ( I and II , respectively) have been synthesized by a selective single addition of a protected 2‐aminoethyl vinyl ether (BocVE) {CH₂ = CH[OCH₂CH₂N(Boc)₂]; Boc = t‐butoxycarbonyl} onto a living cationic poly(n‐butyl vinyl ether) [poly(NBVE)] initiated with the SnCl₄/n‐Bu₄NCl system: ( I ) ‐(NBVE)_n‐ CH₂CH(OCH₂CH₂NH₂)‐H; ( II ) ‐(NBVE)_n‐CH₂CH(OCH₂CH₂NH₂)‐CH₂CO₂H. The single addition was examined with a set of alkene monomers less reactive than NBVE, including BocVE, 2‐chloroethyl vinyl ether, 2‐vinyloxyethylphtalimide, and styrene (St). Upon addition of 10 molar excess of these alkenes onto the living ends, only BocVE led to the intended single adduct, and this was attributed to a chelating interaction of the two carboxylate groups in the terminal BocVE unit with the growing poly(NBVE) terminal, thus sterically hampering further propagation. A simple acid‐catalyzed Boc‐deprotection led to the amino‐functionalized version I . Alternatively, an additional quenching the BocVE‐capped living end (the precursor of I ) with sodium malonate, followed by double deprotection of the Boc and the malonate groups gave the double‐functionalized version II . The selective addition of a single monomer molecule is thus a new method for addressable or site‐specific introduction of functional groups along polymer chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3375–3381, 2010     

Copolymerization of poly(vinyl alcohol)‐graft‐poly(1,4‐dioxan‐2‐one) with designed molecular structure by a solid‐state polymerization method

Poly(vinyl alcohol)‐graft‐poly(1,4‐dioxan‐2‐one) (PVA‐g‐PPDO) with designed molecular structure was synthesized by a solid‐state polymerization. The solid‐state copolymerization was preceded by a graft copolymerization of PDO initiated with PVA as a multifunctional initiator, and Sn (Oct)₂ as a coininitiator/catalyst in a homogeneous molten state. The polymerization temperature was then decreased and the copolymerization was carried out in a solid state. The products prepared by solid‐state polymerization were characterized by ¹H NMR and DSC, and were compared with those synthesized in the homogeneous molten state. The degree of polymerization (D_p), degree of substitution (D_s), yield and the average molecular weight of the graft copolymer with different molecular structure were calculated from the ¹H NMR spectra. The results show that the crystallization process during the solid‐state polymerization may suppress the undesirable inter‐ or intramolecular side reactions, then resulting in a controlled molecular structure of PVA‐g‐PPDO. The results of DSC measurement show that the molecular structures determine the thermal behavior of the PVA‐g‐PPDO. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3083–3091, 2006     

Living cationic polymerization of amide‐functional vinyl ethers: Specific properties of SnCl4‐based initiating system

Living cationic copolymerization of amide‐functional vinyl ethers with isobutyl vinyl ether (IBVE) was achieved using SnCl₄ in the presence of ethyl acetate at 0 °C: the number–average molecular weight of the obtained polymers increased in direct proportion to the monomer conversion with relatively low polydispersity, and the amide‐functional monomer units were introduced almost quantitatively. To optimize the reaction conditions, cationic polymerization of IBVE in the presence of amide compounds, as a model reaction, was also examined using various Lewis acids in dichloromethane. The combination of SnCl₄ and ethyl acetate induced living cationic polymerization of IBVE at 0 °C when an amide compound, whose nitrogen is adjacent to a phenyl group, was used. The versatile performance of SnCl₄ especially for achieving living cationic polymerization of various polar functional monomers was demonstrated in this study as well as in our previous studies. Thus, the specific properties of the SnCl₄ initiating system are discussed by comparing with the Et_xAlCl_3?x systems from viewpoints of hard and soft acids and bases principle and computational chemistry. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6129–6141, 2008     

Preparation of water‐soluble,syndiotacticity‐rich,low molecular weight poly(vinyl alcohol) microfibrils in high yields with the low‐temperature polymerization of vinyl pivalate in tetrahydrofuran and saponification

To prepare water‐soluble, syndiotacticity‐rich poly(vinyl alcohol) (PVA) microfibrils for various industrial applications, we synthesized syndiotacticity‐rich, low molecular weight PVA by the solution polymerization of vinyl pivalate (VPi) in tetrahydrofuran (THF) at low temperatures with 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN) as an initiator and successive saponification of poly(vinyl pivalate) (PVPi). Effects of the initiator and monomer concentrations and the polymerization temperature were investigated in terms of the polymerization behaviors and molecular structures of PVPi and the corresponding syndiotacticity‐rich PVA. The polymerization rate of VPi in THF was proportional to the 0.91 power of the ADMVN concentration, indicating the heterogeneous nature of THF polymerization. The low‐temperature solution polymerization of VPi in THF with ADMVN proved to be successful in obtaining water‐soluble PVA with a number‐average degree of polymerization (P_n) of 300–900, a syndiotactic dyad content of 60–63%, and an ultimate conversion of VPi into PVPi of over 75%. Despite the low molecular weight of PVA with P_n = 800, water‐soluble PVA microfibrillar fibers were prepared because of the high level of syndiotacticity. In contrast, for PVA with P_n = 330, shapeless and globular morphologies were observed, indicating that molecular weight has an important role in the in situ fibrillation of syndiotacticity‐rich PVA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1103–1111, 2002     

Cationic polymerization of vinyl ethers and p‐methoxystyrene by a benign initiating system: Silver salt/arylmethyl halide/dialkyl sulfide

Three vinyl ethers (VEs: isobutyl vinyl ether, ethyl vinyl ether, and isopropyl vinyl ether) and an active styrene derivative, p‐methoxystyrene (pMOS), were employed for cationic polymerization using a benign initiating system, AgClO₄/Ph₂CHBr/dialkyl sulfide. Choosing a sulfide with suitable nucleophilicity was important for achieving controlled polymerization. Additionally, selecting an appropriate reaction temperature based on monomer reactivity was also crucial for suppressing side reactions. Highly controlled polymerizations of VEs and pMOS were further confirmed by proton nuclear magnetic resonance (¹H NMR) and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI‐TOF‐MS). In addition, the coordination of the arylmethyl cation to the added base obviously influenced the initiation, as demonstrated by ¹H NMR analysis. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 861–870     

Investigation of catalyst‐transfer condensation polymerization for synthesis of poly(p‐phenylenevinylene)

Kumada‐Tamao coupling polymerization of 1,4‐dialkoxy‐2‐bromo‐5‐(2‐chloromagnesiovinyl)benzene ( 1 ) and 1,4‐dialkoxy‐2‐(2‐bromovinyl)‐5‐chloromagnesiobenzene ( 2 ) with a Ni catalyst and Suzuki‐Miyaura coupling polymerization of 2‐{2‐[(2,5‐dialkoxy‐4‐iodophenyl)]vinyl}‐4,4,5,5‐tetramethyl‐1,3,2‐dioxaborolane ( 3 ), its bromo counterpart 4 , and 2,5‐dialkoxy‐4‐(2‐bromovinyl)phenylboronic acid ( 5 ) with a Pd initiator were investigated under catalyst‐transfer condensation polymerization conditions for the synthesis of well‐defined poly(p‐phenylenevinylene) (PPV). The Kumada‐Tamao polymerization of vinyl Grignard‐type monomer 1 with Ni(dppp)Cl₂ at room temperature did not proceed, whereas aryl Grignard‐type monomer 2 afforded oligomers of low molecular weight. Matrix‐assisted laser desorption ionization time‐of‐flight (MALDI‐TOF) mass spectra of the polymer obtained from 2 implied that the Grignard end group reacted with tetrahydrofuran to terminate polymerization. On the other hand, Suzuki‐Miyaura polymerization of vinyl boronic acid ester type monomers 3 and 4 and phenylboronic acid type monomer 5 with a Pd initiator and aqueous KOH at ?20 °C to room temperature yielded the corresponding PPV with high molecular weight within a few minutes. However, the molecular weight distribution was broad, and MALDI‐TOF mass spectra showed the peaks of polymers bearing no initiator unit at the chain end, as well as those of polymers with the initiator unit. These results indicated that intermolecular chain transfer of the Pd catalyst occurred. Dehalogenation and disproportionation of the growing end also took place as side reactions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2643‐2653     

Vinyl ether end‐groups in poly(ethylene glycol)s from the Na2CO3‐promoted degradation of 1,3‐dioxolan‐2‐one polymers

The Na₂CO₃‐promoted polymerization of 1,3‐dioxolan‐2‐one (I) to afford poly(ethylene glycol) III was reinvestigated. The reaction appeared to involve a nucleophilic attack against the carbonyl and methylene groups of I to afford poly(carbonate) II with poly(ethylene glycol) linkages and ethylene oxide IV as a side product (10–22%). As the reaction progressed, poly(carbonate) II decreased and poly(ethylene glycol) III increased. Under some conditions, poly(ethylene glycol)s V and VI with vinyl ether terminal groups were formed unexpectedly. The formation of unsaturated products during the polymerization of I/EO (ethylene oxide) has not been reported in the literature. We believe that vinyl ethers were formed from the degradation of poly(carbonate)s and were accompanied by a reduction in molecular weight. The structures of vinyl ethers V and VI were confirmed by hydrogenation of the double bond into the ethyl ether group in VII and VIII, respectively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 152–160, 2000     

Synthesis of amphiphilic copolymer brushes: Poly(ethylene oxide)‐graft‐polystyrene

A well‐defined amphiphilic copolymer brush with poly(ethylene oxide) as the main chain and polystyrene as the side chain was successfully prepared by a combination of anionic polymerization and atom transfer radical polymerization (ATRP). The glycidol was first protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether and then copolymerized with ethylene oxide by the initiation of a mixture of diphenylmethylpotassium and triethylene glycol to give the well‐defined polymer poly(ethylene oxide‐co‐2,3‐epoxypropyl‐1‐ethoxyethyl ether); the latter was hydrolyzed under acidic conditions, and then the recovered copolymer of ethylene oxide and glycidol {poly(ethylene oxide‐co‐glycidol) [poly(EO‐co‐Gly)]} with multiple pending hydroxymethyl groups was esterified with 2‐bromoisobutyryl bromide to produce the macro‐ATRP initiator [poly(EO‐co‐Gly)_(ATRP). The latter was used to initiate the polymerization of styrene to form the amphiphilic copolymer brushes. The object products and intermediates were characterized with ¹H NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, Fourier transform infrared, and size exclusion chromatography in detail. In all cases, the molecular weight distribution of the copolymer brushes was rather narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), and the linear dependence of ln[M₀]/[M] (where [M₀] is the initial monomer concentration and [M] is the monomer concentration at a certain time) on time demonstrated that the styrene polymerization was well controlled. This method has universal significance for the preparation of copolymer brushes with hydrophilic poly(ethylene oxide) as the main chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4361–4371, 2006     

SET‐LRP of vinyl chloride initiated with CHBr3 and catalyzed by Cu(0)‐wire/TREN in DMSO at 25 °C

The single‐electron transfer living radical polymerization (SET‐LRP) of vinyl chloride (VC) initiated with CHBr₃ in dimethylsulfoxide (DMSO) at 25 °C was investigated using Cu(0) powder and Cu(0) wire as the catalyst. It was determined that living kinetics and high conversion are achieved only through the proper calibration of the ratio between Cu(0) and TREN and the concentration of VC in DMSO. For both Cu(0) powder and Cu(0) wire, optimum conversion was achieved with higher levels of TREN than reported in earlier preliminary reports and under more dilute conditions. Using these conditions, 85+% conversion of VC could be achieved with Cu(0) powder and wire to produce white poly(vinyl chloride) (PVC) with M_n = 20,000 and M_w/M_n = 1.4–1.6 in 360 min. The use of Cu(0) wire provides the most effective catalytic system for the LRP of PVC allowing for simple removal and recycling of the catalyst. In the Cu(0) wire‐catalyzed SET‐LRP of VC, the consumption of Cu(0) was monitored as a function of conversion. From these studies, it is evident that the catalyst can be recycled extensively before significant exchange of Cu(0) into Cu(II)X₂ and change in catalyst surface area is observed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 164–172, 2010     

Synthesis of biocompatible and biodegradable block copolymers of polyvinyl alcohol‐block‐poly(ε‐caprolactone) using metal‐free living cationic polymerization

Applications of metal‐free living cationic polymerization of vinyl ethers using HCl · Et₂O are reported. Product of poly(vinyl ether)s possessing functional end groups such as hydroxyethyl groups with predicted molecular weights was used as a macroinitiator in activated monomer cationic polymerization of ε‐caprolactone (CL) with HCl · Et₂O as a ring‐opening polymerization. This combination method is a metal‐free polymerization using HCl · Et₂O. The formation of poly(isobutyl vinyl ether)‐b‐poly(ε‐caprolactone) (PIBVE‐b‐PCL) and poly(tert‐butyl vinyl ether)‐b‐poly(ε‐caprolactone) (PTBVE‐b‐PCL) from two vinyl ethers and CL was successful. Therefore, we synthesized novel amphiphilic, biocompatible, and biodegradable block copolymers comprised polyvinyl alcohol and PCL, namely PVA‐b‐PCL by transformation of acid hydrolysis of tert‐butoxy moiety of PTBVE in PTBVE‐b‐PCL. The synthesized copolymers showed well‐defined structure and narrow molecular weight distribution. The structure of resulting block copolymers was confirmed by ¹H NMR, size exclusion chromatography, and differential scanning calorimetry. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5169–5179, 2009     

Lewis Acid‐Induced N‐Methyleneamines as Initiators in the Synthesis of Secondary Amine‐Terminated Polymers

Summary: The cationic polymerization of poly(tert‐butyl vinyl ether) using N‐methyleneamine equivalents derived from a Lewis acid/1,3,5‐trimethylhexahydro‐1,3,5‐triazine (TMTA) co‐initiating system is reported. The resulting polymers possessed secondary amine functionality at the chain terminus, verified by derivatization with 4‐chloro‐7‐nitrobenzo‐2‐oxa‐1,3‐diazole (NBD‐Cl) and subsequent analysis with GPC‐UV (470 nm) and ¹H NMR.

Use of N‐methyleneamine equivalents lacking aryl substituents to afford amine‐terminated poly(tert‐butyl vinyl ether).     

Synthesis and hydrogel formation of fluorine‐containing amphiphilic ABA triblock copolymers

Fluorine‐containing amphiphilic ABA triblock copolymers, poly(2‐hydroxyethyl vinyl ether)‐block‐poly[2‐(2,2,3,3,3‐pentafluoropropoxy)ethyl vinyl ether]‐block‐poly(2‐hydroxyethyl vinyl ether) [poly(HOVE‐b‐PFPOVE‐b‐HOVE)] (HFH), poly[2‐(2,2,3,3,3‐pentafluoropropoxy)ethyl vinyl ether]‐block‐poly(2‐hydroxyethyl vinyl ether)‐block‐poly[2‐(2,2,3,3,3‐pentafluoropropoxy)ethyl vinyl ether] [poly(PFPOVE‐b‐HOVE‐b‐PFPOVE)] (FHF), and poly(n‐butyl vinyl ether)‐block‐poly(2‐hydroxyethyl vinyl ether)‐block‐poly(n‐butyl vinyl ether) [poly(NBVE‐b‐HOVE‐b‐NBVE)] (LHL), were synthesized, and their behavior in water was investigated. The aforementioned polymers were prepared by sequential living cationic polymerization of 2‐acetoxyethyl vinyl ether (AcOVE) and PFPOVE or NBVE, followed by hydrolysis of acetyl groups in polyAcOVE. FHF and LHL formed a hydrogel in water, whereas HFH gave a homogeneous aqueous solution. In addition, the gel‐forming concentration of FHF was much lower than that of corresponding LHL. Surface‐tension measurements of the aqueous polymer solutions revealed that all the triblock copolymers synthesized formed micelles or aggregates above about 1.0 × 10^?4 mol/L. The surface tensions of HFH and FHF solutions above the critical micelle concentration were lower than those of LHL, indicating high surface activity of fluorine‐containing triblock copolymers. Small‐angle X‐ray scattering measurements revealed that HFH formed a core‐shell sperical micelle in 1 wt % aqueous solutions, whereas the other block copolymers caused more conplicated assembly in the solutions. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3751–3760, 2001     

Synthesis of dual pH/temperature‐responsive polymers with amino groups by living cationic polymerization

For the precision synthesis of primary amino functional polymers, cationic polymerization of a phthalimide‐containing vinyl ether monomer precursor, 2‐vinyloxyethyl phthalimide (PIVE), was examined using a base‐assisting initiating system. Living polymerization of PIVE in CH₂Cl₂ in the presence of 1,4‐dioxane as an added base yielded nearly monodispersed polymers (M_w/M_n < 1.1) and higher molecular weight polymers, which have never been obtained using other initiating systems. Furthermore, block copolymers with hydrophobic or hydrophilic groups could be prepared. The deprotection of the pendant phthalimide groups gave well‐defined pH‐responsive polymers with pendant primary amino groups. Dual‐stimuli–responsive block copolymers having a pH‐responsive polyamine segment and a thermosensitive segment self‐assembled in water in response to both pH and temperature. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1207–1213, 2010     

Preparation of ultrahigh‐molecular‐weight syndiotactic poly(vinyl pivalate) monodisperse microspheres by low‐temperature suspension polymerization of vinyl pivalate

The particle size distributions of poly(vinyl pivalate) (PVPi) produced from low‐temperature suspension polymerization of vinyl pivalate (VPi) with 2,2′‐azobis(4‐methoxy‐2,4‐dimethylvaleronitrile) (AMDMVN) as an initiator have been studied. By controlling various synthesis parameters, near‐monodisperse PVPi microspheres from 100 to 400 μm were obtained that are expected to be precursors of near‐monodisperse syndiotactic poly(vinyl alcohol) (PVA) microspheres for biomedical embolic applications. The mean particle diameter follows the relationship: the volume average diameter, D_vad ∝ Y^0.26[VPi]^0.52[AMDMVN]^?0.25[PVA]^0.40T^?8.35Rpm^?0.67, where Y, [VPi], [AMDMVN], [PVA], T, and Rpm are the fractional conversion, concentrations of VPi, AMDMVN, and suspending agent, polymerization temperature, and agitation speed during the polymerization of VPi, respectively. The polydispersity of the particle size distribution of PVPi decreased with decreasing conversion, [AMDMVN], T, and Rpm and with increasing [VPi]. In the case of [PVA], optimization of the suspension stability led to a narrow particle size distribution. Ultrahigh‐molecular‐weights PVPi and PVA (number‐average degrees of polymerization of PVPi (25,000–32,000) and PVA (14,000–17,500), of high syndiotactic diad content (63%), and of high ultimate conversion of VPi into PVPi (85–95%) were obtained by suspension polymerization at 10 °C, followed by saponification. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 789–800, 2005     

Synthesis of fluorine‐containing star‐shaped poly(vinyl ether)s via arm‐linking reactions in living cationic polymerization

Various types of fluorine‐containing star‐shaped poly(vinyl ether)s were successfully synthesized by crosslinking reactions of living polymers based on living cationic polymerization. Star polymers with fluorinated arm chains were prepared by the reaction between a divinyl ether and living poly(vinyl ether)s with fluorine groups (C₄F₉, C₆F₁₃, and C₈F₁₇) at the side chain using cationogen/Et_1.5AlCl_1.5 in a fluorinated solvent (dichloropentafluoropropanes), giving star‐shaped fluorinated polymers in high yields with a relatively narrow molecular weight distribution. The concentration of living polymers for the crosslinking reaction and the molar feed ratio of a bifunctional vinyl ether to living polymers affected the yield and molecular weight of the star polymers. Star polymers with block arms were prepared by a linking reaction of living block copolymers of a fluorinated segment and a nonfluorinated segment. Heteroarm star‐shaped polymers containing two‐ or three‐arm species were synthesized using a mixture of different living polymer species for the reaction with a bifunctional vinyl ether. The obtained polymers underwent temperature‐induced solubility transitions in various organic solvents, and their concentrated solutions underwent sol–gel transitions, based on the solubility transition of a thermoresponsive fluorinated segment. Furthermore, a slight amount of fluorine groups were shown to be effective for physical gelation when those were located at the arm ends of a star polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012