The direct architecture of carbon fiber‐carbon nanofiber hierarchical reinforcements for superior interfacial properties of CF/epoxy composites

A simple and efficient chemical method was developed to graft directly carbon nanofibers (CNFs) onto carbon fiber (CF) surface to construct a CF‐CNF hierarchical reinforcing structure. The grafted CF reinforcements via covalent ester linkage at low temperature without any usage of dendrimer or catalyst was investigated by FTIR, X‐ray photoelectron spectroscopy, Raman, scanning electron microscopy, atomic force microscopy, dynamic contact angle analysis, and single fiber tensile testing. The results indicated that the CNFs with high density could effectively increase the polarity, wettability, and roughness of the CF surface. Simultaneous enhancements of the interfacial shear strength, flexural strength, and dynamic mechanical properties as well as the tensile strength of CFs were achieved, for an increase of 75.8%, 21.9%, 21.7%, and 0.5%, respectively. We believe the facile and effective method may provide a novel and promising interface design strategy for next‐generation advanced composite structures.     

E‐glass/DGEBA/m‐PDA single fiber composites: New insights into the statistics of fiber fragmentation

The interfacial shear strength is a critical parameter for assessing composite performance and failure behavior. This parameter is usually obtained from a single‐fiber fragmentation test that induces sequential fracture with increasing strain of a single embedded fiber with output being the distribution of fragment lengths. An exact analytical form for the expected fragment length distribution is still not known. Such data are often fit empirically to Weibull, shifted‐exponential, or lognormal distribution functions. In this report, new insights into the sequential fiber fracture process are provided by detailed analyses of the fiber break locations along the length of the embedded fiber. From this approach, the high degree of uniformity of the break coordinate loci strongly suggests that there can be no mechanistic rationale for the use of the Weibull, or lognormal, or exponential functions to fit the fragment lengths. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2301–2312, 2009     

Effects of plasma treatment of carbon fibers on interfacial properties of BMI resin composites

High performance continuous fiber surface modification by inductively coupled RF plasma (ICP) and dielectric barrier discharge (DBD) low temperature plasma were conducted. X-ray photoelectron spectroscopy (XPS) and other analytical testing methods systematically studied plasma treatment time, discharge power, discharge pressure, etc, on fiber surface state, surface composition, and surface shape changes in the appearance and wetting properties. The results show that after plasma treatment the surface of the fiber is grafted with a large number of polar functional groups such as carboxyl groups and hydroxyl groups. The surface roughness increases, the surface free energy increases, and the fiber wetting property is significantly improved, resulting in improvement in interlaminar shear strength (ILSS) between the fiber and the resin matrix. Finally, the surfaces of the fibers and its relationship with interfacial properties of fiber reinforced bismaleimide composites are also discussed.     

Investigation of irradiation dose rate on curing characteristics of carbon fiber/polymer composites by low‐energy electron beam

During in situ low‐energy electron beam (E‐Beam) curing for carbon fiber‐reinforced polymer composite, prepregs undergoes 3 sequenced curing processes, namely E‐Beam‐induced curing, postray curing after irradiation, and thermally induced curing. In this study, the irradiation dose rate (IDR) is demonstrated to be influential on the redistribution of the curing portions in the 3 curing stages and directly influences the interlaminar bonding quality of the stepwise cured laminates. Differential scanning calorimetry results showed that higher IDR resulted in higher temperature of irradiated prepregs, and hence, a higher degree of curing was induced by the E‐Beam within a dose range of 0 to 500 kGy as compared to lower IDRs, which decreased the interlaminar physical adhesive quality between layers. Analysis indicates that other than pure physical adhesion between uncured layers, postray curing can further enhance the interlaminar shear strength for cured laminates by introducing cross‐layer chemical bonding in the interlaminar zone.     

The effect of surface modification with nitric acid on the mechanical and tribological properties of carbon fiber‐reinforced thermoplastic polyimide composite

Polyacrylamideacrylate (PAN)‐based carbon fibers were submitted to nitric acid oxidation treatments to improve the interfacial adhesion of the carbon fiber (CF)‐reinforced polyimide (CF/PI) composite. The carbon fiber surfaces were characterized by X‐ray photoelectron spectroscopy (XPS). Nitric acid oxidation not only affects the oxygen concentration but also produces an appreciable change in the nature of the chemical functions, namely the conversion of hydroxy‐type oxygen into carboxyl functions. Nitric acid oxidation treatment modifies the element constituting the fiber, the nitrogen concentration being about 1.2 times higher at the fiber external surface compared to the untreated one. The mechanical and tribological properties of the polymide (PI) composites reinforced by the carbon fibers treated with nitric acid oxidation were investigated. Results showed that the tensile strength of the CF/PI composites improved remarkably due to nitric acid treatment along with enhancement in friction and wear performance. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis of non‐destructive amido group functionalized multi‐walled carbon nanotubes and their application in antistatic and thermal conductive polyetherimide matrix nanocomposites

Thermal conductive and antistatic polyetherimide (PEI) nanocomposites were fabricated by encapsulating non‐destructive amido group functionalized multi‐walled carbon nanotubes (MWCNTs) into the PEI matrix. Briefly, nearly half of acyl chloride groups in poly (acryloyl chloride) reacted with sodium azide and formed acyl azide groups, which could conjunct with MWCNTs via non‐destruction nitrenes addition reaction. The remaining acyl chloride groups in poly (acryloyl chloride) hydrolyzed into carboxyl groups, therefore COOH‐rich MWCNTs (MWCNTs@azide polyacrylic acid) were synthesized without serious damage to the MWCNTs. Then, MWCNTs@azide polyacrylic acid were then reacted with p‐Phenylene diamine (PPD) and transformed to amido group functionalized MWCNTs (MWCNTs@PPD). MWCNTs@PPD could participate into the in situ polymerization of PEI matrix, where the conjunction between bisphenol A dianhydride and amido groups on MWCNTs@PPD guaranteed the strong covalent bonding at the PEI/MWCNTs interface, which directly avoided the aggregation of MWCNTs. Owing to the non‐destructive modification of MWCNTs and tight matrix/filler interface, the volume electric and thermal conductivity of as‐prepared nanocomposites was up to 6.4 × 10^?8 S/cm (1.0 wt%, MWCNTs@PPD) and 0.43 W/(m · K) (4.0 wt%, MWCNTs@PPD), respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of carbon fiber surface functionality on the moisture absorption behavior of carbon fiber/epoxy resin composites

Polyacrylonitrile (PAN)‐based carbon fibers were electrochemically oxidized in aqueous ammonium bicarbonate with increasing current density. The electrochemical treatment led to significant changes of surface physical properties and chemical structures. The oxidized fibers showed much cleaner surfaces and increased levels of oxygen functionalities. However, it was found that there was no correlation between surface roughness and the fiber/resin bond strength, i.e. mechanical interlocking did not play a major role in fiber/resin adhesion. Increases in surface chemical functionality resulted in improved fiber/resin bonding and increased interlaminar shear strength (ILSS) of carbon fiber reinforced epoxy composites. The relationship between fiber surface functionality and the hydrothermal aging behavior of carbon fiber/epoxy composites was investigated. The existence of free volume resulted from poor wetting of carbon fibers by the epoxy matrix and the interfacial chemical structure were the governing factors in the moisture absorption process of carbon fiber/epoxy composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Self‐reinforced composites based on commercial PP woven fabrics and a random PP copolymer modified with quartz

Self‐reinforced composites based on commercial polypropylene (PP) woven fabrics and a random PP copolymer modified with quartz were obtained by film stacking. The effect of the incorporation of quartz on the materials fracture and failure behavior was studied through uniaxial tensile tests and quasi‐static fracture experiments. Acoustic emission analysis was also performed in situ in the tensile tests. A higher consolidation quality was obtained for the composites containing quartz. In the composite with random PP modified with 5 wt% quartz, the higher consolidation and the better dispersion of quartz particles positively impacted on the materials tensile and fracture behavior. From the results of acoustic emission analysis, fiber fracture appears as the dominant failure mechanism in the investigated composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Increased interfacial adhesion between carbon fiber and poly(vinylidene fluoride) by an aqueous sizing agent

The adhesion behavior of poly(vinylidene fluoride) (PVDF) to carbon fiber (CF) has always been a huge challenge, on account of the inertness nature of PVDF and the lack of reactive functional groups. In this work, a novel maleic anhydride grafted PVDF (MPVDF) aqueous sizing agent was prepared to modify the interface between CF and PVDF matrix. The surface properties of desized, MPVDF‐sized, and PVDF‐sized carbon fibers were characterized by the scanning electron microscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, and dynamic contact angle analysis test. The results demonstrated that the surface roughness increased from 39 to 55 nm, and surface energy increased from 40 to 74 mN m^?1 after MPVDF sizing treatment. The content of activated carbon atoms increased from 31.0% to 48.4%. Subsequently, the interlaminar shear strength was examined, for which was a critical indicator of the interfacial adhesion between CF and matrix. Compared with the desized CF, the value of interlaminar shear strength increased from 14.8 MPa to 25.5 MPa improved by 72% because of the improved H‐bonding formation, surface roughness, and wettability for MPVDF‐sized CF. In addition, the flexural strength and modulus were also improved by 47% and 74%, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of surface properties on the interfacial adhesion in carbon fiber/epoxy composites

A polyacrylonitrile‐based carbon fiber was electrochemically oxidized in an aqueous ammonium bicarbonate solution with current density of up to 2.76 A/m² at room temperature. X‐ray photoelectron spectroscopy revealed that the oxygen content increased with increasing current density before approaching saturation. The increase can be divided into two regions, the rapid increase region (0–1.78 A/m²) and a plateau region (1.78–2.76 A/m²). The surface chemistry analysis showed that the interlaminar shear strength (ILSS) value of the carbon fiber/epoxy composite could be improved by 24.7%. The carbon structure was examined using Raman spectroscopy in terms of order/disorder in the graphite structure and the results indicated that the relative percentage of graphite carbon in the form of sp² hybridization increased above a current density of 1.39 A/m². The increasing non‐polar graphite carbon on the carbon fiber surface decreased the surface energy. As a result, both the surface free energy () and its polar component () decreased when current density increased above 1.78 A/m². The ILSS value had no direct relationship with the nature and surface density of the oxygen‐containing functional groups nor with the carbon structure. It is the surface free energy (), especially the polar component (), which played a critical role in affecting the interfacial adhesion of carbon fiber/epoxy composites. The ILSS value changed with increasing current density and could be divided into three distinct regions, as chemical interaction region (I), anchor force region (II) and matrix damage region (III). Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of carbon fiber surface treatments on the flexural strength and tribological properties of short carbon fiber/polyimide composites

Pitch‐based short carbon fibers (CFs) were treated by air oxidation and cryogenic nitrogen, respectively. Thereafter the treated and untreated CFs were incorporated into polyimide (PI) matrix to form composites. The CFs before and after treatment were examined by XPS and SEM.The flexural strength of the specimen was determined in a three‐point test machine and the tribological properties of PI composites sliding against GCr15 steel rings were evaluated on an M‐2000 model ring‐on‐block test rig. The results show that the surface of the treated CFs became rougher. Lots of active groups formed on the CF surface after air oxidation.The treatment can effectively improve the mechanical and tribological properties in their PI composites due to the enhanced fiber‐matrix interfacial bonding. Copyright © 2008 John Wiley & Sons, Ltd.     

Tailoring the surface chemistry of carbon fiber and E‐glass composites for improved adhesion

The main challenges in the manufacture of composite materials are low surface energy and the presence of silicon‐containing contaminants, both of which greatly reduce surface adhesive strength. In this study, carbon fiber (CF) and E‐glass epoxy resin composites were surface treated with the Accelerated Thermo‐molecular adhesion Process (ATmaP). ATmaP is a multiaction surface treatment process where tailored nitrogen and oxygen functionalities are generated on the surface of the sample through the vaporization and atomization of n‐methylpyrrolidone solution, injected via specially designed flame‐treatment equipment. The treated surfaces of the polymer composites were analyzed using XPS, time of flight secondary ion mass spectrometry (ToF‐SIMS), contact angle (CA) analysis and direct adhesion measurements. ATmaP treatment increased the surface concentration of polar functional groups while reducing surface contamination, resulting in increased adhesion strength. XPS and ToF‐SIMS showed a significant decrease in silicon‐containing species on the surface after ATmaP treatment. E‐glass composite showed higher adhesion strength than CF composite, correlating with higher surface energy, higher concentrations of nitrogen and C?O functional groups (from XPS) and higher concentrations of oxygen and nitrogen‐containing functional groups (particularly C₂H₃O⁺ and C₂H₅NO⁺ molecular ions, from ToF‐SIMS). Copyright © 2010 John Wiley & Sons, Ltd.     

Mechanical hysteresis,interface and filler–filler structural breakdowns in ethylene vinyl acetate organoclay composites internally lubricated via radiolytically degraded PTFE microparticles

Inclusion of two or more distinct fillers (hybrid fillers) in a matrix is envisaged to entail synergetic advantages. This study reports synthesis and property evaluation of a novel hybrid filler‐based polymer composite containing two types of fillers with distinct attributes namely mechanical reinforcement and internal lubrication. Poly(tetrafluoroethylene) micro‐particles (PTFEMP) were synthesized via radiolytic‐mechanical degradation and used as an internal lubricant for organoclay (OC) reinforced ethylene vinyl acetate (EVA) matrix. Mechanical hysteresis, nonlinear and linear small amplitude oscillatory shear rheology, morphology, small angle X‐ray scattering (SAXS), dynamic coefficient of friction (DCoF), surface wetting and thermoxidative stability of binary and ternary composites were investigated. In EVA/OC composites, PTFEMP acted as an internal lubricant and reduced DCoF in a volume fraction‐dependent fashion. OC and PTFEMP both increased the mechanical hysteresis of EVA; though the magnitude of hysteresis was much less in PTFEMP. Intriguingly, PTFEMP reduced mechanical hysteresis of EVA/OC composites that is work done during loading and unloading stress–strain cycles was considerably reduced with the inclusion of PTFEMP in EVA/OC composites. SAXS results revealed mass fractals and the presence of an interfacial layer in EVA/OC composites but not in EVA/PTFEMP composites. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 509–519     

Mechanical,thermal, and UV‐shielding behavior of silane surface modified ZnO‐reinforced phthalonitrile nanocomposites

In the present work, zinc oxide nanoparticles were treated with aminopropyl trimethoxy silane‐coupling agent and used as a new kind of reinforcement for a typical high performance bisphenol‐A‐based phthalonitrile resin. The resulted nanocomposites were characterized for their mechanical, thermal, and optical properties. Results from the tensile test indicated that the tensile strength and modulus as well as the toughness state of the matrix were all enhanced with the increasing of the nanoparticles amount. Thermogravimetric analysis showed that the starting decomposition temperatures and the residual weight at 800°C were highly improved upon adding the nanofillers. At 6 wt% nanoloading, the glass transition temperature and the storage modulus were considerably enhanced reaching about 359°C and 3.7 GPa, respectively. The optical tests revealed that the neat resin possesses excellent UV‐shielding properties, which were further enhanced by adding the nanofillers. Furthermore, the fractured surfaces of the nanocomposites analyzed by scanning electron microscope exhibited homogeneous and rougher surfaces compared with that of the pristine resin. Finally, the good dispersion of the reinforcing phase into the matrix was confirmed by a high resolution transmission electron microscope. Copyright © 2015 John Wiley & Sons, Ltd.     

Diameter dependence of hybrid shish‐kebab structure in polyethylene/carbon material fiber composites

PE chains can proceed template crystal growth on multi‐walled carbon nanotubes (MWCNTs) surface and develop into hybrid shish‐kebab (HSK) abiding by the “soft epitaxy” mechanism. For large‐diameter carbon nanofiber (CNF), the lattice matching and epitaxy are the main mechanism for hybrid structure formation under the static state. This study provided a new understanding of HSK formation, wherein PE underlay on the surface of carbon material fiber played an important role. The shear flow induced PE chains to orient along the CNF surface and formed PE underlayer. Subsequently, ordered subglobules were periodically formed along the CNF axis and finally evolved to typical HSK structures with well‐aligned arraying PE lamellae rather than random one. As the diameter increased to 7000 nm, even though the graphite (002) planes in carbon fibers (CFs) was similar to that in CNFs, the attractive van der Waals interactions between CFs and PE chains were too weak to drive enough PE chains to absorb on the CFs surface and form PE underlay even under the shear flow, leading to the absence of PE lamellae on the CF surface. Based on that, the “soft epitaxy” could be the main formation mechanism of HSK structures for carbon material fibers regardless of their diameters. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 297–303     

The effect of a semi‐industrial masterbatch process on the carbon nanotube agglomerates and its influence in the properties of thermoplastic carbon nanotube composites

This study details an industrial process to prepare polypropylene (PP) composites reinforced with different loadings (0.5–10wt.%) of carbon nanotubes (CNTs) from a direct dilution of a masterbatch produced by an optimized extrusion compounding process. The work demonstrates how the anisotropy in the distribution of CNTs can have a positive effect on the electrical conductivity and fracture toughness of the resulting composites. The composite with the highest loading of CNTs had an electrical conductivity of 10^?2 S/m comparable with those reported in the available literature. The composites showed anisotropy in their properties that seems to be caused by the non‐homogeneous distribution of the agglomerates produced by the orientation of the flow direction during the injection process. The composites produced in this work exhibited a fracture toughness up to 55% higher than neat PP and failed by polymer ductile tearing. It was found that the CNT agglomerates distributed throughout the matrix increased the toughness of PP by promoting plastic deformation of the matrix during the fracture process and by a slight load transfer between the polymer matrix and the CNTs of the agglomerates. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 189–197     

Effect of low current density electrochemical oxidation on the properties of carbon fiber‐reinforced epoxy resin composites

Changes in surface physicochemical structures of polyacrylonitrile‐based carbon fibers resulted from low current density electrochemical oxidation were monitored by scanning electron microscopy (SEM) and X‐ray photoelectron spectroscopy (XPS). The relationship between the interlaminar shear strength (ILSS) values of carbon fiber‐reinforced polymers (CFRPs) and carbon fiber surface chemistry including elemental ratios and the relative content of oxygen‐containing functional groups were researched. SEM results revealed that the electrochemical oxidation got rid of surface contaminants generated during the production process. XPS analysis showed that the relative contents of oxygen and nitrogen increased by 446% and 202%, respectively, after the electrochemical oxidation. Carbon fiber surface chemistry was of paramount importance to the interfacial properties of CFRPs. The higher the carbon fiber surface activity, the better the interfacial bonding was, and an increase in the acidic‐group contents was responsible for a higher ILSS value. However, when the current density increased to 1.0 A/m², the interfacial bonding between carbon fiber and the epoxy resin became weak which led to the decline in ILSS values. Copyright © 2012 John Wiley & Sons, Ltd.     

Grafting of polymers onto a carbon‐fiber surface by ligand‐exchange reaction of poly(vinyl ferrocene‐co‐vinyl monomer) with polycondensed aromatic rings of the surface

To improve the surface of carbon fiber, the grafting reaction of copolymer containing vinyl ferrocene (VFE) onto a carbon‐fiber surface by a ligand‐exchange reaction between ferrocene moieties of the copolymer and polycondensed aromatic rings of carbon fiber was investigated. The copolymer containing VFE was prepared by the radical copolymerization of VFE with vinyl monomers, such as methyl methacrylate (MMA) and styrene, using 2,2′‐azobisisobutyronitrile as an initiator. By heating the carbon fiber with poly(VFE‐co‐MMA) (number‐average molecular weight: 2.1 × 10⁴) in the presence of aluminum chloride and aluminum powder, the copolymer was grafted onto the surface. The percentage of grafting reached 46.1%. On the contrary, in the absence of aluminum chloride, no grafting of the copolymer was observed. Therefore, it is considered that the copolymer was grafted onto the carbon‐fiber surface by a ligand‐exchange reaction between ferrocene moieties of the copolymer and polycondensed aromatic rings of carbon fiber. The molar number of grafted polymer chain on the carbon‐fiber surface decreased with increasing molecular weight of poly(VFE‐co‐MMA) because the steric hindrance of grafted copolymer on the carbon‐fiber surface increases with increasing molecular weight of poly(VFE‐co‐MMA). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1868–1875, 2002     

Annealing induced electrical conductivity jump of multi‐walled carbon nanotube/polypropylene composites and influence of molecular weight of polypropylene

Multi‐walled carbon nanotube (MWCNT)/polypropylene (PP) composites were prepared by a micro melt mixing process. As‐prepared composites had relatively low electrical conductivity due to the disruption of MWCNT network by strong shear. The electrical conductivity jumped to high values throughout an annealing process above the melting temperature of PP. The significant enhancement of electrical conductivity was influenced by annealing time, temperature, and content of MWCNTs. In particular, molecular weight of PP played an important role in affecting the conductivity enhancement. The molecular weight of PP was varied from 190,000 to 340,000 to examine its effect on the electrical conductivity. By comparing the conductivity enhancement behavior of composites with different molecular weight PPs and observing the morphology evolution during annealing, it was found that reaggregation of MWCNTs and the subsequent formation of MWCNT network during annealing are the main reasons for the jump of electrical conductivity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Structural and mechanical behavior of polypropylene/ maleated styrene‐(ethylene‐co‐butylene)‐styrene/sisal fiber composites prepared by injection molding

Hybrid composites consisting of isotactic poly(propylene) (PP), sisal fiber (SF), and maleic anhydride grafted styrene‐(ethylene‐co‐butylene)‐styrene copolymer (MA‐SEBS) were prepared by melt compounding, followed by injection molding. The melt‐compounding torque behavior, thermal properties, morphology, crystal structure, and mechanical behavior of the PP/MA‐SEBS/SF composites were systematically investigated. The torque test, thermogravimetric analysis, differential scanning calorimetric, and scanning electron microscopic results all indicated that MA‐SEBS was an effective compatibilizer for the PP/SF composites, and there was a synergism between MA‐SEBS and PP/SF in the thermal stability of the PP/MA‐SEBS/SF composites. Wide‐angle X‐ray diffraction analysis indicated that the α form and β form of the PP crystals coexisted in the PP/MA‐SEBS/SF composites. With the incorporation of MA‐SEBS, the relative amount of β‐form PP crystals decreased significantly. Mechanical tests showed that the tensile strength and impact toughness of the PP/SF composites were generally improved by the incorporation of MA‐SEBS. The instrumented drop‐weight dart‐impact test was also used to examine the impact‐fracture behavior of these composites. The results revealed that the maximum impact force (F_max), impact‐fracture energy (E_T), total impact duration (t_r), crack‐initiation time (t_init), and crack‐propagation time (t_prop) of the composites all tended to increase with an increasing MA‐SEBS content. From these results, the incorporation of MA‐SEBS into PP/SF composites can retard both the crack initiation and propagation phases of the impact‐fracture process. These prolonged the crack initiation and propagation time and increased the energy consumption during impact fracture, thereby leading to toughening of PP/MA‐SEBS/SF composites. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1214–1222, 2002