Theoretical derivation of tangential velocity profiles in a flat vortex chamber-influence of turbulence and wall friction

Summary As part of a study on the hydrodynamics of a cyclone separator, a theoretical investigation of the flow pattern in a flat box cyclone (vortex chamber) has been carried out. Expressions have been derived for the tangential velocity profile as influenced by internal friction (eddy viscosity) and wall friction. The most important parameter controlling the tangential velocity profile is = –u ₀ R/(v+ ), where u ₀ is the radial velocity at the outer radius R of the cyclone, the kinematic liquid viscosity and is the kinematic eddy viscosity. For values of greater than about 10 the tangential velocity profile is nearly hyperbolic, for smaller than 1 the tangential velocity even decreases towards the centre. It is shown how and also the wall friction coefficient may be obtained from experimental velocity profiles with the aid of suitable graphs. Because of the close relation between eddy viscosity and eddy diffusion, measurements of velocity profiles in flat box cyclones will also provide information on the eddy motion of particles in a cyclone, a motion reducing its separation efficiency.List of symbols A cross-sectional area of cyclone inlet - h height of cyclone - p static pressure in cyclone - p static pressure difference in cyclone between two points on different radius - r radius in cyclone - r ₁ radius of cyclone outlet - R radius of cyclone circumference - u radial velocity in cyclone - u ₀ radial velocity at circumference of flat box cyclone - v tangential velocity - v ₀ tangential velocity at circumference of flat box cyclone - w axial velocity - z axial co-ordinate in cyclone - friction coefficient in flat box cyclone (for definition see § 5) - ₁ value of friction coefficient for ₁<< ₂ - ₂ value of friction coefficient for ₂<<1 - = - ₁ value of for ₁<< ₂ - ₂ value of for ₂<<1 - thickness of laminar boundary layer - =/h - turbulent kinematic viscosity - ratio of z to h - k ratio of height of cyclone to radius R of cyclone - parameter describing velocity profile in cyclone =–u ₀ R/(+) - kinematic viscosity of fluid - density of fluid - ratio of r to R - ₁ value of at outlet of cyclone - ₂ value of at inner radius of cyclone inlet - _w shear stress at cyclone wall - angular momentum in cyclone/angular momentum in cyclone inlet - ₁ value of at = ₁ - ₂ value of at = ₂     

Representation of the rheological properties of polymer melts in terms of complex fluidity

In dynamic rheological experiments melt behavior is usually expressed in terms of complex viscosity ^* () or complex modulusG ^* (). In contrast, we attempted to use the complex fluidity ^* () = 1/µ ^* () to represent this behavior. The main interest is to simplify the complex-plane diagram and to simplify the determination of fundamental parameters such as the Newtonian viscosity or the parameter of relaxation-time distribution when a Cole-Cole type distribution can be applied. ^* () complex shear viscosity - () real part of the complex viscosity - () imaginary part of the complex viscosity - G ^* () complex shear modulus - G() storage modulus in shear - G() loss modulus in shear - J ^* () complex shear compliance - J() storage compliance in shear - J() loss compliance in shear - shear strain - rate of strain - angular frequency (rad/s) - shear stress - loss angle - ^* () complex shear fluidity - () real part of the complex fluidity - () imaginary part of the complex fluidity - ₀ zero-viscosity - ₀ average relaxation time - h parameter of relaxation-time distribution     

Optical co-ordinates in general relativity 2 — the problem of distance

Summary Let denote the congruence of null geodesics associated with a given optical observer inV ₄. We prove that determines a unique collection of vector fieldsM₍₎ ( =1, 2, 3) and ₍₀₎ overV ₄, satisfying a weak version of Killing's conditions.This allows a natural interpretation of these fields as the infinitesimal generators of spatial rotations and temporal translation relative to the given observer. We prove also that the definition of the fieldsM₍₎ and ₍₀₎ is mathematically equivalent to the choice of a distinguished affine parameter f along the curves of, playing the role of a retarded distance from the observer.The relation between f and other possible definitions of distance is discussed.

---

Sommario Sia la congruenza di geodetiche nulle associata ad un osservatore ottico assegnato nello spazio-tempoV ₄. Dimostriamo che determina un'unica collezione di campi vettorialiM₍₎ ( =1, 2, 3) e ₍₀₎ inV ₄ che soddisfano una versione in forma debole delle equazioni di Killing. Ciò suggerisce una naturale interpretazione di questi campi come generatori infinitesimi di rotazioni spaziali e traslazioni temporali relative all'osservatore assegnato. Dimostriamo anche che la definizione dei campiM₍₎, ₍₀₎ è matematicamente equivalente alla scelta di un parametro affine privilegiato f lungo le curve di, che gioca il ruolo di distanza ritardata dall'osservatore. Successivamente si esaminano i legami tra f ed altre possibili definizioni di distanza in grande.

---

---

Work performed in the sphere of activity of: Gruppo Nazionale per la Fisica Matematica del CNR.     

The dynamic performance of the Weissenberg rheogoniometer III. Large amplitude oscillatory shearing — harmonic analysis

The harmonic content of the nonlinear dynamic behaviour of 1% polyacrylamide in 50% glycerol/water was studied using a standard Model R 18 Weissenberg Rheogoniometer. The Fourier analysis of the Oscillation Input and Torsion Head motions was performed using a Digital Transfer Function Analyser.In the absence of fluid inertia effects and when the amplitude of the (fundamental) Oscillation Input motion _I is much greater than the amplitudes of the Fourier components of the Torsion Head motion _Tn empirical nonlinear dynamic rheological propertiesG _n (, ⁰),G _n (, ⁰) and/or _n (, ⁰), _n (, ⁰) may be evaluated without a-priori-knowledge of a rheological constitutive equation. A detailed derivation of the basic equations involved is presented.Cone and plate data for the third harmonic storage modulus (dynamic rigidity)G ₃ (, ⁰), loss modulusG ₃ (, ⁰) and loss angle ₃ (, ⁰) are presented for the frequency range 3.14 × 10^–2 1.25 × 10² rad/s at two strain amplitudes, _CP ⁰ = 2.27 and 4.03. Composite cone and plate and parallel plates data for both the third and fifth harmonic dynamic viscosities ₃ (, ⁰), _S (, ⁰) and dynamic rigiditiesG ₃ (, ⁰),G ₅ (, ⁰) are presented for strain amplitudes in the ranges 1.10 _CP ⁰ 4.03 and 1.80 _PP ⁰ 36 for a single frequency, = 3.14 × 10^–1 rad/s. Good agreement was obtained between the results from both geometries and the absence of significant fluid inertia effects was confirmed by the superposition of the data for different gap widths.     

The theory of a vibrating-rod viscometer

The paper presents a complete theory for a viscometer based upon the principle of a circular-section rod, immersed in a fluid, performing transverse oscillations perpendicular to its axis. The theory is established as a result of a detailed analysis of the fluid flow around the rod and is subject to a number of criteria which subsequently constrain the design of an instrument. Using water as an example it is shown that a practical instrument can be designed so as to enable viscosity measurement with an accuracy of ±0.1%, although it is noted that many earlier instruments failed to satisfy one or more of the newly-established constraints.Nomenclature A, D constants in equation (46) - A _m , B _m , C _m , D _m constants in equations (50) and (51) - A _j , B _j constants in equation (14) - a _j ⁺ , a _j ^– wavenumbers given by equation (15) - C _f drag coefficient defined in equation (53) - c speed of sound - D _b drag force of fluid b - D ₀ coefficient of internal damping - E extensional modulus - f(z) initial deformation of rod - f(), F _m () functions of defined in equation (41) - F force in the rod - force per unit length near t=0 - F dimensionless force per unit length near t=0 - g _m amplitude of transient force - G modulus of rigidity - h, h* functions defined by equations (71) and (72) - H functions defined by equation (69) and (70) - I second moment of area - I _0,1, J _0,1, K _0,1 modified Bessel functions - k, k functions defined in equations (2) - L half-length of oscillator - Ma Mach number - m _b added mass per unit length of fluid b - m _s mass per unit length of solid - n _j eigenvalue defined in equations (15) and (16) - R radius of rod - R _c radius of container - r radial coordinate - T tension - T _visc temperature rise due to heat generation by viscous dissipation - t time - v _r , v radial and angular velocity components - y lateral displacement - y ₀ initial lateral displacement - y ₁, y ₂ successive maximum lateral displacement - z axial coordinate - dimensionless tension - dimensionless mass of fluid - dimensionless drag of fluid - amplification factor - logarithmic decrement in a fluid - _a , _b logarithmic decrement in fluids a and b - ₀ logarithmic decrement in vacuo - _j logarithmic decrement in mode j in a fluid - spatial resolution of amplitude - _v voltage resolution - r, , , _s, , increments in R, , , _s , , - dimensionless amplitude of oscillation - dimensionless axial coordinate - angular coordinate - _f thermal conductivity of fluid - viscosity of fluid - viscosity of fluid calculated on assumption that * - _a , _b viscosity of fluids a and b - _m constants in equation (10) - dimensionless displacement - _j j the component of - density of fluid - _a , _b density of fluids a and b - _s density of tube or rod material - dimensionless radial coordinate - * dimensionless radius of container - dimensionless times - spatial component of defined in equation (11) - _j , _tm jth, mth component of - dimensionless streamfunction - ⁰, ¹ components of in series expansion in powers of - streamfunction - dimensionless frequency (based on ) - angular frequency - ₀ angular frequency in absence of fluid and internal damping - _j angular frequency in mode j in a fluid - _a , _b frequencies in fluids a and b     

Heat transfer from laminar flow in ducts with elliptic cross-section

Summary The cooling of a hot fluid in laminar Newtonian flow through cooled elliptic tubes has been calculated theoretically. Numerical data have been computed for the two values 1.25 and 4 of the axial ratio of the elliptic cross-section . For =1.25 the influence of non-zero thermal resistance between outmost fluid layer and isothermal surroundings has also been investigated. Special attention has been given to the distribution of heat flux around the perimeter; when increases the flux varies more with the position at the circumference. This positional dependence becomes less pronounced, however, as the (position-independent) thermal resistance of the wall increases.Flattening of the conduit, while maintaining its cross-sectional area constant, improves the cooling. Comparison with rectangular pipes shows that this improvement is not as marked with elliptic as with rectangular pipes.Nomenclature A _k =A _{m, n} coefficients of expansion (6) - a, b half-axes of ellipse, b<a - a _p =a _{r, s} coefficients of representation (V) - D hydraulic diameter, = 4S/P; S = cross-sectional area, P = perimeter - D _e equivalent diameter, according to (13) - n coordinate (outward) normal to the tube wall - T temperature of fluid - T _i temperature of fluid at the inlet - T _s temperature of surroundings - v ₀ mean velocity of fluid - v _z longitudinal velocity of fluid - x, y carthesian coordinates coinciding with axes of ellipse - z coordinate in flow direction - , dimensionless half-axes of ellipse, =a/D and =b/D - _t heat transfer coefficient from fluid at bulk temperature to surroundings; equation (11) - _w heat transfer coefficient at the wall; equation (3) - axial ratio of ellipse, = a/b = / - , , , dimensionless coordinates; =x/D, =y/D, =z/D, =n/D - dimensionless temperature, = (T–T _s)/(T _i–T _s) - ₀ cup-mixing mean value of ; equation (10) - thermal conductivity of fluid - _m,n = _k eigenvalue - c volumetric heat capacity of fluid - _{m, n} = _k = _k eigenfunction; equations (6) and (I) - Nu total Nusselt number, = _t D/ - Nusselt number at large distance from the inlet - Nu _w wall Nusselt number, = _w D/, based on _w - Pé Péclet number, = ₀ Dc/     

Existence theorem for a minimum problem with free discontinuity set

We study the variational problem Where is an open set in ⁿ ,n2gL ^q () L (), 1q<+, O<, <+ andH _n–1 is the (n–1)-dimensional Hausdorff Measure.     

Eine analytische Näherungslösung für die eingefrorene laminare Grenzschichtströmung eines binären Gemisches

Zusammenfassung Für die eingefrorene laminare Grenzschichtströmung eines teilweise dissoziierten binären Gemisches entlang einer stark gekühlten ebenen Platte wird eine analytische Näherungslösung angegeben. Danach läßt sich die Wandkonzentration als universelle Funktion der Damköhler-Zahl der Oberflächenreaktion angeben. Für das analytisch darstellbare Konzentrationsprofil stellt die Damköhler-Zahl den Formparameter dar. Die Wärmestromdichte an der Wand bestehend aus einem Wärmeleitungs- und einem Diffusionsanteil wird angegeben und diskutiert. Das Verhältnis beider Anteile läßt sich bei gegebenen Randbedingungen als Funktion der Damköhler-Zahl ausdrücken.

---

An analytical approximation for the frozen laminar boundary layer flow of a binary mixture

An analytical approximation is derived for the frozen laminar boundary layer flow of a partially dissociated binary mixture along a strongly cooled flat plate. The concentration at the wall is shown to be a universal function of the Damkohler-number for the wall reaction. The Damkohlernumber also serves as a parameter of shape for the concentration profile which is presented in analytical form. The heat transfer at the wall depending on a conduction and a diffusion flux is derived and discussed. The ratio of these fluxes is expressed as a function of the Damkohler-number if the boundary conditions are known.

---

Formelzeichen A Atom - A₂ Molekül - C Konstante in Gl. (20) - c₁=1/(2C) Konstante in Gl. (35) - c_p spezifische Wärme bei konstantem Druck - D binärer Diffusionskoeffizient - Ec=u ² /(2h_f) Eckert-Zahl - h spezifische Enthalpie - h_t=h+u²/2 totale spezifische Enthalpie - h _A ⁰ spezifische Dissoziationsenthalpie - K_w Reaktionsgeschwindigkeitskonstante der heterogenen Wandreaktion - 1= /( ) Champman-Rubesin-Parameter - Le=Pr/Sc Lewis-Zahl - M Molmasse - p statischer Druck - Pr= c_pf/ Prandtl-Zahl - q_w Wärmestromdichte an der Wand - q_cw, q_dw Wärmeleitungsbzw. Diffusionsanteil der Wärmestromdichte an der Wand - universelle Gaskonstante - R=/(2M_a) individuelle Gaskonstante der molekularen Komponente - Re_x= u x/ Reynolds-Zahl - Sc=/( D) Schmidt-Zahl - T absolute Temperatur - T_d=h _A ⁰ /R charakteristische Dissoziationstemperatur - u, v x- und y-Komponenten der Geschwindigkeit - U=u/u normierte x-Komponente der Geschwindigkeit - x, y Koordinaten parallel und senkrecht zur Platte Griechische Symbole - =A/ Dissoziationsgrad - Grenzschichtdicke - ₂ Impulsverlustdicke - Damköhler-Zahl der Oberflächenreaktion - =T/T normierte Temperatur - =y/ normierter Wandabstand - Wärmeleitfähigkeit - dynamische Viskosität - , ^* Ähnlichkeitskoordinaten - Dichte - Schubspannung Indizes A auf ein Atom bezogen - M auf ein Molekül bezogen - f auf den eingefrorenen Zustand bezogen - w auf die Wand bezogen - auf den Außenrand der Grenzschicht bezogen     

Free convection on an arbitrarily inclined plate with uniform surface heat flux

This paper proposed a proper inclination parameter and transformation variables for the analysis of free convection from an inclined plate with uniform surface heat flux to fluids of any Prandtl number. Very accurate numerical results and a simple correlation equation are obtained for arbitrary inclination from the horizontal to the vertical and for 0.001 Pr. Maximum deviation between the correlated and calculated data is less than 1.2%.

---

Freie Konvektion an einer beliebig geneigten Platte mit erheblicher Wärmestromdichte an der Oberfläche

Zusammenfassung Für die Berechnung von freier Konvektion von Fluiden mit beliebiger Prandtl-Zahl an einer geneigten Platte mit einheitlicher Wärmestromdichte an der Oberfläche werden ein zweckmäßiger Neigungsparameter und Transformationsvariablen eingeführt. Sehr genaue numerische Ergebnisse und eine einfache Korrelationsgleichung wurden für beliebige Neigungen zwischen der Horizontalen und der Vertikalen und für 0.001Pr erhalten. Die größte Abweichung zwischen Korrelations- und berechneten Daten liegt bei weniger als 1.2%.

---

Nomenclature f reduced stream function - g gravitational acceleration - h local heat transfer coefficient - k thermal conductivity - Nu local Nusselt number - p static pressure difference - Pr Prandtl number - q _w wall heat flux - Ra* modified local Rayleigh number,g(q _w x/k)x ³/ - T fluid temperature - T temperature of ambient fluid - u velocity component inx-direction - v velocity component iny-direction - x coordinate parallel to the plate - y coordinate normal to the plate Greek symbols thermal diffusivity - thermal expansion coefficient - (Ra* |sin|)^1/5/( Ra* cos)^1/6 - ( Ra* cos)^1/6+( Ra*|sin|)^1/5 - (y/x) - dimensionless temperature, (T–T )/(q _w x/k) - kinematic viscosity - [1+( Ra* cos)^1/6/( Ra*|sin|)^1/5]^–1 - density of fluid - Pr/(1+Pr) - _w wall shear stress - angle of inclination measured from the horizontal - stream function - dimensionless static pressure difference, p x ²/ ⁴     

Parameter determination for thermodynamical models of the pseudoelastic behaviour of shape memory alloy by resistivity measurements and infrared thermography

Two thermodynamical models of pseudoelastic behaviour of shape memory alloys have been formulated. The first corresponds to the ideal reversible case. The second takes into account the hysteresis loop characteristic of this shape memory alloys.Two totally independent techniques are used during a loading-unloading tensile test to determine the whole set of model parameters, namely resistivity and infrared thermography measurements. In the ideal case, there is no difficulty in identifying parameters.Infrared thermography measurements are well adapted for observing the phase transformation thermal effects.Notations 1 austenite 2 martensite - ₍₎ Macroscopic infinitesimal strain tensor of phase - ₍₂₎ ^f Traceless strain tensor associated with the formation of martensite phase - Macroscopic infiniesimal strain tensor - Macroscopic infinitesimal strain tensor deviator - _f Trace - Equivalent strain - ^pe Macroscopic pseudoelastic strain tensor - x Distortion due to parent (austenite =1)product (martensite =2) phase transformation (traceless symmetric second order tensor) - M Total mass of a system - M() Total mass of phase - V Total volume of a system - V() Total volume of phase - z=M(2)/M Weight fraction of martensite - 1-z=M(1)/M Weight fraction of austenite - u ₀ ^* () Specific internal energy of phase (=1,2) - s ₀ ^* () Specific internal entropy of phase - Specific configurational energy - Specific configurational entropy - ₀ ^f (T) Driving force for temperature-induced martensitic transformation at stress free state ( ₀ ^f T) = T ^*–Ts ^*) - Kirchhoff stress tensor - Kirchhoff stress tensor deviator - Equivalent stress - Cauchy stress tensor - Mass density - K Bulk moduli (K ₀=K) - L Elastic moduli tensor (order 4) - E Young modulus - Energetic shear (₀ = ) - Poisson coefficient - M _s ^o (M _F ^o ) Martensite start (finish) temperature at stress free state - A _s ^o (A _F ^o ) Austenite start (finish) temperature at stress free state - C _v Specific heat at constant volume - k Conductivity - Pseudoelastic strain obtained in tensile test after complete phase transformation (AM) (unidimensional test) - ₀ Thermal expansion tensor - r Resistivity - 1MPa 10⁶ N/m ² - ⁽⁾ Specific free energy of phase - _n Specific free energy at non equilibrium (R model) - _n ^eq Specific free energy at equilibrium (R model) - _n ^v Volumic part of ^eq - Specific free energy at non equilibrium (R _L model) - _conf Specific coherency energy (R _L model) - _c Specific free energy at constrained equilibria (R _L model) - _it (T) Coherency term (R _L model)     

Chaos and integrability in a nonlinear wave equation

We consider the parametrized family of equations _tt ,u- _xx u-au+u ₂ ² u=O,x(0,L), with Dirichlet boundary conditions. This equation has finite-dimensional invariant manifolds of solutions. Studying the reduced equation to a four-dimensional manifold, we prove the existence of transversal homoclinic orbits to periodic solutions and of invariant sets with chaotic dynamics, provided that =2, 3, 4,.... For =1 we prove the existence of infinitely many first integrals pairwise in involution.     

The contribution of internal degrees of freedom to the non-Newtonian rheology of model polymer fluids

We report non-equilibrium molecular dynamics simulations of rigid and non-rigid dumbbell fluids to determine the contribution of internal degrees of freedom to strain-rate-dependent shear viscosity. The model adopted for non-rigid molecules is a modification of the finitely extensible nonlinear elastic (FENE) dumbbell commonly used in kinetic theories of polymer solutions. We consider model polymer melts — that is, fluids composed of rigid dumbbells and of FENE dumbbells. We report the steady-state stress tensor and the transient stress response to an applied Couerte strain field for several strain rates. We find that the rheological properties of the rigid and FENE dumbbells are qualitatively and quantitatively similar. (The only exception to this is the zero strain rate shear viscosity.) Except at high strain rates, the average conformation of the FENE dumbbells in a Couette strain field is found to be very similar to that of FENE dumbbells in the absence of strain. The theological properties of the two dumbbell fluids are compared to those of a corresponding fluid of spheres which is shown to be the most non-Newtonian of the three fluids considered.Symbol Definition b dimensionless time constant relating vibration to other forms of motion - F force on center of mass of dumbbell - F _i force on bead i of dumbbell - F force between center of masses of dumbbells and - F _ij force between beads i and j - h vector connecting bead to center of mass of dumbbell - H dimensionless spring constant for dumbbells, in units of / ² - I moment of inertia of dumbbell - J general current induced by applied field - k _B Boltzmann's constant - L angular momentum - m mass of bead, (= m/2) - M mass of dumbbell, g - N number of dumbbells in simulation cell - P translational momentum of center of mass of dumbbell - P pressure tensor - P _xy xy component of pressure tensor - Q separation of beads in dumbbell - Q _eq equilibrium extension of FENE dumbbell and fixed extension of rigid dumbbell - Q ₀ maximum extension of dumbbell - r _ij vector connecting beads i and j - r position vector of center of mass dumbbell - R vector connecting centers of mass of two dumbbells - t time - t ^* dimensionless time, in units of m/ - T ^* dimensionless temperature, in units of /k - u potential energy - u velocity vector of flow field - u _x x component of velocity vector - V volume of simulation cell - X general applied field - strain rate, s^–1 - ^* dimensionless shear rate, in units of /m ² - general transport property - Lennard-Jones potential well depth - friction factor for Gaussian thermostat - shear viscosity, g/cms - ^* dimensionless shear viscosity, in units of m/ ² - ^* dimensionless number density, in units of ^–3 - Lennard-Jones separation of minimum energy - relaxation time of a fluid - angular velocity of dumbbell - orientation angle of dumbbell      

Transport in ordered and disordered porous media II: Generalized volume averaging

In this paper we develop the averaged form of the Stokes equations in terms of weighting functions. The analysis clearly indicates at what point one must choose a media-specific weighting function in order to achieve spatially smoothed transport equations. The form of the weighting function that produces the cellular average is derived, and some important geometrical theorems are presented.Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - A _p surface area of a particle, m² - d _p 6V _p/A_p, effective particle diameter, m - g gravity vector, m/s² - I unit tensor - K _m permeability tensor for the weighted average form of Darcy's law, m² - L general characteristic length for volume averaged quantities, m - L _p general characteristic length for volume averaged pressure, m - L characteristic length for the porosity, m - L _v characteristic length for the volume averaged velocity, m - l characteristic length (pore scale) for the-phase - l _i i=1, 2, 3 lattice vectors, m - (y) weighting function - m(–y) (y), convolution product weighting function - _v special weighting function associated with the traditional averaging volume - m _v special convolution product weighting function associated with the traditional averaging volume - m _g general convolution product weighting function - m _V unit cell convolution product weighting function - m _C special convolution product weighting function for ordered media which produces the cellular average - m _D special convolution product weighting function for disordered media - m _M master convolution product weighting function for ordered and disordered media - n unit normal vector pointing from the-phase toward the-phase - p pressure in the-phase, N/m² - p_m superficial weighted average pressure, N/m² - p _m intrinsic weighted average pressure, N/m² - p traditional intrinsic volume averaged pressure, N/m² - p p p _m , spatial deviation pressure, N/m² - r ₀ radius of a spherical averaging volume, m - r _m support of the convolution product weighting function, m - r position vector, m - r position vector locating points in the-phase, m - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - V velocity vector in the-phase, m/s - vm superficial weighted average velocity, m/s - v _m intrinsic weighted average velocity, m/s - V volume of the-phase contained in the averaging volume, m³ - V _p volume of a particle, m³ - v traditional superficial volume averaged velocity, m/s - v v p _m spatial deviation velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - _m m * . weighted average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m² - V /V, volume fraction of the-phase     

Dynamic-mechanical properties of a bitumen-silica composite

Summary The dynamic-mechanical behaviour of bitumensilica composites is described by a linear biparabolic model. Its mathematical expression allows the calculation of the mean relaxation times () either at different temperatures and given filler contents or for diverse filler contents () at imposed temperatures. At fixed filler concentration and within restricted temperature domains, obeys Arrhenius' law. The activation energies are respectively close to 10 kcal/mole (creep) and 30 kcal/mole (glass-transition). varies exponentially with. The mathematical treatment of the expressions ofE , as a function of temperature and of, leads to a general equation relating the complex modulus to temperature, frequency and filler content. A unique master curve, accounting for the viscoelastic behaviour of the composites, in limited ranges, can thus be constructed.

---

Zusammenfassung Das dynamisch-mechanische Verhalten von Bitumen-Siliziumdioxyd-Zusammensetzungen kann durch ein lineares biparabolisches Modell beschrieben werden. Sein mathematischer Ausdruck erlaubt die Ausrechnung der mittleren Relaxationszeiten () entweder für verschiedene Temperaturen bei gegebenem Füllstoffgehalt oder für unterschiedliche Siliziumdioxydmengen () bei bekannter Temperatur. Für einen bestimmten Füllstoffgehalt folgt in einem beschränkten Temperaturbereich dem Arrheniusschen Gesetz. Die Aktivierungsenergien betragen näherungsweise 10 kcal/Mol (Fließprozeß) bzw. 30 kcal/Mol (Glasübergang). ändert sich exponentiell mit. Die mathematische Umformung der Ausdrücke fürE und als Funktion der Temperatur und des Parameters ergibt eine allgemeine Gleichung, die den komplexen Modul mit der Temperatur, der Frequenz und dem Füllstoffgehalt verknüpft. Man kann eine einzige Masterkurve bilden, die das viskoelastische Verhalten der Zusammensetzungen zumindest in begrenzten Bereichen beschreibt.

---

Résumé Le comportement mécanique dynamique des composites à base de bitume et de silice peut être décrit par un modèle biparabolique linéaire. L'expression mathématique permet le calcul des temps moyens () de relaxation d'une part aux différentes températures, à taux de charge donné, et d'autre part pour diverses valeurs des taux de charge (paramètre) à température imposée. A taux de charge donné, et pour des domaines de température restreints, suit la loi d'Arrhénius. Les énergies apparentes d'activation sont respectivement voisines de 10 kcal/mole (processus de fluage) et de 30 kcal/mole (passage à l'état vitreux). Avec, varie exponentiellement. L'évaluation mathématique deE , de en fonction deT et de conduit à une expression générale du module complexe en fonction de la température, de la fréquence et du taux de charge. On peut donc construire une courbe maitresse unique qui décrit entièrement, mais dans des domaines restreints, le comportement viscoélastique des composites.

---

---

With 6 figures     

Effects of MHD free convection and mass transfer on the flow past an oscillating infinite coaxial vertical circular cylinder

The effects of MHD free convection and mass transfer are taken into account on the flow past oscillating infinite coaxial vertical circular cylinder. The analytical expressions for velocity, temperature and concentration of the fluid are obtained by using perturbation technique.

---

Einwirkungen von freier MHD-Konvektion und Stoffübertragung auf eine Strömung nach einem schwingenden unendlichen koaxialen vertikalen Zylinder

Zusammenfassung Die Einwirkungen der freien MHD-Konvektion und Stoffübertragung auf eine Strömung nach einem schwingenden, unendlichen, koaxialen, vertikalen Zylinder wurden untersucht. Die analytischen Ausdrücke der Geschwindigkeit, Temperatur und Fluidkonzentration sind durch die Perturbationstechnik erhalten worden.

---

Nomenclature C _p Specific heat at constant temperature - C the species concentration near the circular cylinder - C _w the species concentration of the circular cylinder - C the species concentration of the fluid at infinite - * dimensionless species concentration - D chemical molecular diffusivity - g acceleration due to gravity - Gr Grashof number - Gm modified Grashof number - K thermal conductivity - Pr Prandtl number - r _a ,r _b radius of inner and outer cylinder - a, b dimensionless inner and outer radius - r,r coordinate and dimensionless coordinate normal to the circular cylinder - Sc Schmidt number - t time - t dimensionless time - T temperature of the fluid near the circular cylinder - T _w temperature of the circular cylinder - T temperature of the fluid at infinite - u velocity of the fluid - u dimensionless velocity of the fluid - U ₀ reference velocity - z,z coordinate and dimensionless coordinate along the circular cylinder - coefficient of volume expansion - * coefficient of thermal expansion with concentration - dimensionless temperature - H ₀ magnetic field intensity - coefficient of viscosity - _e permeability (magnetic) - kinematic viscosity - electric conductivity - density - M Hartmann number - dimensionless skin-friction - frequency - dimensionless frequency     

Dissipation effects on MHD free convection flow past a semi-infinite vertical plate

Viscous and Joule dissipation effects are considered on MHD free convection flow past a semi-infinite isothermal vertical plate under a uniform transverse magnetic field. Series solutions in powers of a dissipation number (=gx/c _p) have been employed and the resulting ordinary differential equations have been solved numerically. The velocity and temperature profiles are shown on graphs and the numerical values of ₁(0)/₀(0) (, temperature function) have been tabulated. It is observed that the dissipation effects in the MHD case become more dominant with increasing values of the magnetic field parameter (=M ²/(Gr _x /4)^1/2) and the Prandtl number.     

A third order scheme in the vlasov theory and some consequences in the evolution of few body systems

Summary A set of implemented evolution equations, describing the coherent nonlinear interaction of plasma waves, based on the perturbation method, has been derived, taking into account initial value effects and third order nonlinearities in the modal amplitudes.The equations reduce, in the appropriate limit, to well known stochastic triplets of hydrodynamic type.It is argued that, the stochastization mechanism of the decay instability in strongly damped regime, may be interpreted as a Duffing-type behavior.

---

Sommario Si presenta un sistema di equazioni di evoluzione descrivente l'interazione coerente nonlineare di onde di plasma, tenendo conto di effetti di condizioni iniziali e nonlinearità del terzo ordine nelle ampiezze modali. Le equazioni si riducono, nel limite appropriato, a ben noti tripletti stocastici di tipo idrodinamico.Si ipotizza che il processo di stocastizzazione della instabilità di decadimento, in regime di forte dissipazione, possa essere interpretato da un modello dinamico del tipo Duffing.

---

Lyst of greek symbols omega (lower case)=frequency - delta (1.c.)=partial derivative - pi (1.c.)=greek pi (=3,14r. units) in (26) - Sigma (Capital case)=Summation symbol - Delta (C.c)=def. as in (14) - epsilon (1.c.) def. as in (10) - sigma (1.c.)=def. as in (36) - gamma (1.c.)=def. as in (37) - beta (1.c.)=def. as in (37) - ro, (1.c.)=def. as in (37) - alfa (1.c.)=def. in connection with _k in (60) - Gamma (C.c.)=def. as in (63) and (66), (67) - delta (1.c.)=def. as in (66) - psi (1.c.)=def. as in (75) - fi (1.c.)=def. in (71) in connection with ₀ - Fi (C.c.)=def. as in (75) - Omega (C.c.)=def. in (78)     

Stochastic response of structures with small geometric imperfections

Summary A probabilistic model of the geometric imperfections of a real structure is proposed, in order to provide a general theory of the stochastic response of structures in presence of small random deviations from the perfect scheme. The main statistical measures of the stochastic response are derived and an application to the study of a particular conservative elastic system is developed.

---

Sommario Si propone una teoria generale della risposta probabilistica di strutture, in presenza di piccole deviazioni aleatorie dei dati iniziali rispetto allo schema geometrico perfetto. Si deducono le principali proprietà statistiche della risposta della struttura a sollecitazioni esterne deterministiche, e si sviluppa una applicazione riguardante il comportamento aleatorio di un particolare sistema elastico conservativo.

---

List of symbols element of the sample space of events - _kn random variables modelling the structural imperfections - P(o) probability density of random variables - random imperfection of the unloaded structure - u additional displacement of the loaded structure - u_o deterministic fundamental solution for the perfect structure - difference between the additional displacement of the loaded structure and the deterministic fundamental solution for the perfect structure - V₁=u₁ buckling mode of the perfect structure - _i intrinsic coordinates of the structure - suitable measure of the magnitude of the random imperfections - scalar geometric variable representing the internal product - random imperfection divided by - single scalar variable denoting the magnitude of the prescribed loads - potential energy of the structure - potential energy of the perfect structure - difference between and - _c lowest critical load - _s real local maximum for the magnitude of the prescribed loads - _c divided by _S - E{} expected value of a random variable - ² variance of a random variable - , random variables defined by Eq. (21)     

Saint-Venant's principle in linear two-dimensional elasticity for non-striplike domains

Let be a simply connected domain in the x ₁-x ₂ plane which lies within the strip 0<x ₂, is a simple closed piecewise smooth curve. Let l= [(x ₁, x ₂): (x ₁, x ₂) and x ₁>0], _l = [(x ₁ x ₂): (x ₁ ,x ₂) and x ₁>1>0].Suppose that a two-dimensional homogeneous isotropic elastic body occupies , that a self-equilibrated stress loading is applied to - l, and that l is stress-free. Knowles [2] and Flavin [6] showed that the elastic energy in _l decays exponentially with respect to l with an exponential decay constant of the form k/b, where k is a universal constant. It is shown here that a decay constant of the form c/ may be obtained where c is a universal constant and is a characteristic dimension of , which is more appropriate than b for general non-striplike domains. In addition, an appropriate decay theorem is obtained for coil-like domains.