Determination of arsenic species by inductively coupled plasma mass spectrometry with ion chromatography

Five arsenic species, trimethylarsine oxide, dimethylarsenic acid, monomethylarsonic acid, arsenobetaine and sodium arsenite, in urine were analysed by inductively coupled plasma mass spectrometry with ion chromatography (IC ICP MS). Since the toxicities of different arsenic compounds are different, speciation of arsenic compounds is very important in the investigation of metabolisms. In this paper, we applied ion chromatography (IC) as a separation device and inductively coupled plasma mass spectrometry (ICP MS) as a detection device. For separation of the five arsenic compounds, an anion-exchange column and, as mobile phase, tartaric acid were used. The eluent from the IC column was introduced directly into the nebulizer of the ICP MS and analysed at 75 amu. Detection limits were from 4 to 9 pg as arsenic.     

固相萃取分离-电感耦合等离子体质谱法测定海产品中的无机砷

分别将N-（β氨乙基）-?-氨丙基三甲氧基硅烷(AEAPTMS)、3-巯丙基三甲氧基硅烷(MPTMS)与四乙氧基硅烷（TEOS)水解共聚,制备氨基\巯基键合的硅胶材料。将此材料作为固相萃取（SPE）小柱的填充材料,建立了固相萃取快速分离富集海产品样品中五价砷As（Ⅴ）和三价砷As（Ⅲ）电感耦合等离子体质谱法（ICP-MS）测定海产品中无机砷的方法。研究了固相萃取小柱对无机砷的吸附原理、性能和洗脱条件,在pH3～4范围内固相萃取小柱材料有良好的选择吸附性,利用2%硝酸可将As（Ⅴ）洗脱,利用2%硝酸+0.1mol/L KIO3可将As（Ⅲ）洗脱。实际样品检测的加标回收率在72～103%之间,方法实现了海产品样品中无机砷形态快速、方便、准确的检测。     

Simultaneous electrothermal vaporization and nebulizer sample introduction system for inductively coupled plasma mass spectrometry

The novel analytical application of the combination of an inline electrothermal vaporization (ETV) and nebulization source for inductively coupled plasma mass spectrometry (ICP-MS) has been studied. Wet plasma conditions are sustained during ETV introduction by 200 mL/min gas flow through the nebulizer, which is merged with the ETV transport line at the torch. The use of a wet plasma with ETV introduction avoided the need to change power settings and torch positions that normally accompany a change from wet to dry plasma operating conditions. This inline-ETV source is shown to have good detection limits for a variety of elements in both HNO₃ and HCl matrices. Using the inline-ETV source, improved limits of detection (LOD) were obtained for elements typically suppressed by polyatomic interferences using a nebulizer. Specifically, improved LODs for ⁵¹V and ⁵³Cr suffering from Cl interferences (⁵¹ClO⁺ and ⁵³ClO⁺ respectively) in a 1% HCl matrix were obtained using the inline-ETV source. LODs were improved by factors of 65 and 22 for ⁵¹V and ⁵³Cr, respectively, using the inline-ETV source compared to a conventional concentric glass nebulizer. For elements without polyatomic interferences, LODs from the inline-ETV were comparable to conventional dry plasma ETV-ICP time-of-flight mass spectrometry results. Lastly, the inline-ETV source offers a simple means of changing from nebulizer introduction to inline-ETV introduction without extinguishing the plasma. This permits, for example, the use of the time-resolved ETV-ICP-MS signals to distinguish between an analyte ion and polyatomic isobar.     

An introduction to inductively coupled plasma source mass spectrometry

Inductively coupled plasma (ICP) source mass spectrometry is a revolutionary new method of analysis, combining the speed and convenience of sample introduction into the ICP with the high sensitivity and isotope ratio capability of atomic mass spectrometry.     

Laser ablation and arc/spark solid sample introduction into inductively coupled plasma mass spectrometers

Sample introduction using laser ablation and arc and spark ablation is reviewed. Few references were found in the literature on the use of spark or arc ablation as a sample introduction technique into the ICP-MS and emphasis is therefore placed on the use of laser ablation sampling, particularly for Inductively Coupled Plasma Mass Spectrometry (ICP-MS) detection; however, many of the principles can also be applied to optical emission detection. The applications of the techniques are described, with particular emphasis on micro-sampling of geological materials.     

Determination of rare earth elements in tomato plants by inductively coupled plasma mass spectrometry techniques

In recent years identification of the geographical origin of food has grown more important as consumers have become interested in knowing the provenance of the food that they purchase and eat. Certification schemes and labels have thus been developed to protect consumers and genuine producers from the improper use of popular brand names or renowned geographical origins. As the tomato is one of the major components of what is considered to be the healthy Mediterranean diet, it is important to be able to determine the geographical origin of tomatoes and tomato‐based products such as tomato sauce. The aim of this work is to develop an analytical method to determine rare earth elements (RRE) for the control of the geographic origin of tomatoes. The content of REE in tomato plant samples collected from an agricultural area in Piacenza, Italy, was determined, using four different digestion procedures with and without HF. Microwave dissolution with HNO₃ + H₂O₂ proved to be the most suitable digestion procedure. Inductively coupled plasma quadrupole mass spectrometry (ICPQMS) and inductively coupled plasma sector field plasma mass spectrometry (ICPSFMS) instruments, both coupled with a desolvation system, were used to determine the REE in tomato plants in two different laboratories. A matched calibration curve method was used for the quantification of the analytes. The detection limits (MDLs) of the method ranged from 0.03 ng g^?1 for Ho, Tm, and Lu to 2 ng g^?1 for La and Ce. The precision, in terms of relative standard deviation on six replicates, was good, with values ranging, on average, from 6.0% for LREE (light rare earth elements) to 16.5% for HREE (heavy rare earth elements). These detection limits allowed the determination of the very low concentrations of REE present in tomato berries. For the concentrations of REE in tomato plants, the following trend was observed: roots > leaves > stems > berries. Copyright © 2009 John Wiley & Sons, Ltd.     

Efficiency of sample introduction into inductively coupled plasma by graphite furnace electrothermal vaporization

A laboratory constructed graphite furnace electrothermal vaporizer (GF-ETV) was used for studying transport efficiencies. This device enables collection of the vaporization products that exit the central sampling hole of the horizontal graphite tube. For determination of the transport efficiency between the GF-ETV and the ICP-torch three methods were tested: (1) deposition of the aerosol particles and the vapour of certain elements by mixing the vaporization product with supersaturated steam and subsequent condensation (direct method); (2) dissolution of the deposited sample fraction from the interface components (indirect method); and (3) calculation from line intensities when applying GF-ETV and pneumatic nebulization sample introduction methods using mercury as a reference element. The latter, `mercury reference method' required 100% transport efficiency for mercury with the ETV, which could be approximated with the use of argon as carrier gas (without halocarbon addition). With a 200 cm³/min flow rate of internal argon in the graphite tube, the transport efficiency was between 67 and 76% for medium volatility elements (Cu, Mn and Mg) and between 32 and 38% for volatile elements (Cd and Zn). By adding carbon tetrachloride vapour to the internal argon flow, the transport efficiency increased to 67–73% for the five elements studied.     

Multiplexed electrothermal vaporization sample introduction system for inductively coupled plasma spectrometry

A multiplexed electrothermal vaporization (ETV) system for sample introduction into an inductively coupled plasma was designed in an effort to increase sample turn-around time. Tungsten filaments (300 W), originally designed for overhead projectors, were chosen for use as ETVs to avoid the high power requirements associated with other ETV devices, e.g. graphite furnaces (2–3 kW). In short, we have multiplexed the thermal stages have been multiplexed such that a vaporization event can take place every 20 s. This represents a significant increase in the throughput typically associated with ETV-ICPMS, which is normally approximately 20–30 samples/h. Evaluated with respect to common figure of merit criteria, the performance of the multiplexed ETV system is similar to that seen with conventional graphite furnace ETV systems. However, several mass spectral interferences can be introduced by the presence of W into the plasma, which hinder the analysis of certain metals (Hg, Mo, etc.). Thus, other low power vaporizers (e.g. Re, Ta) should be considered for use in future systems.     

Determination of arsenic, selenium, and antimony in cloud water by inductively coupled plasma mass spectrometry

The capability of inductively coupled plasma mass spectrometry in determining trace levels of As, Se, and Sb in cloud water was evaluated. Preliminary studies focused on identifying and eliminating potential interferences in the cloud water matrix, the choice of appropriate internal standards, and system optimization. The detection limits for As, Se, and Sb were 20, 100, 20 pg/mL using pneumatic nebulization, and 5, 25, 5 pg/mL, respectively, using ultrasonic nebulization with a precision of better than 5% RSD. The accuracy was demonstrated by the analysis of a NIST commercial reference material, SRM 1643d. In all cases, the results from ICP-MS analysis agreed within 4% of the certified values. Comparative analysis of cloud water samples obtained from a site downwind from large pollution sources (Whiteface Mountain, New York) and Changlagali Pakistan, a rural mountain peak, was carried out by hydride generation atomic absorption (HGAA) spectrometry. There was excellent agreement between the ICP-MS and HGAA results.     

Determination of arsenic, selenium, and antimony in cloud water by inductively coupled plasma mass spectrometry

The capability of inductively coupled plasma mass spectrometry in determining trace levels of As, Se, and Sb in cloud water was evaluated. Preliminary studies focused on identifying and eliminating potential interferences in the cloud water matrix, the choice of appropriate internal standards, and system optimization. The detection limits for As, Se, and Sb were 20, 100, 20 pg/mL using pneumatic nebulization, and 5, 25, 5 pg/mL, respectively, using ultrasonic nebulization with a precision of better than 5% RSD. The accuracy was demonstrated by the analysis of a NIST commercial reference material, SRM 1643d. In all cases, the results from ICP-MS analysis agreed within 4% of the certified values. Comparative analysis of cloud water samples obtained from a site downwind from large pollution sources (Whiteface Mountain, New York) and Changlagali Pakistan, a rural mountain peak, was carried out by hydride generation atomic absorption (HGAA) spectrometry. There was excellent agreement between the ICP-MS and HGAA results. Received: 31 July 1997 / Revised: 28 October 1997 / Accepted: 31 October 1997     

Determination of vanadium by reaction cell inductively coupled plasma mass spectrometry

Recent advances in inductively coupled plasma mass spectrometry (ICP-MS) have included the addition of interference reduction technologies, such as collision and reaction cells, to improve its detection capability for certain elements that suffer from polyatomic interferences. The principle behind reaction cell (RC)-ICP-MS is to remove a particular polyatomic interference by dissociation or formation of a different polyatomic species that no longer interferes with the analyte of interest. However, some interferences cannot be removed by commonly reported reaction gases, such as hydrogen, oxygen, or methane, necessitating using more reactive and hazardous gases, such as ammonia. The current study investigates oxygen as a reaction gas in RC-ICP-MS to specifically react with vanadium analyte ions, rather than the interferents, to produce a polyatomic analyte species and thereby provide a way to analyze for vanadium in complex environmental matrices. The technique has been tested on a series of river water, tap water, and synthetic laboratory samples, and shown to be successful in vanadium analyses in high chloride and sulfate matrices. The zinc isobaric interference on the new vanadium oxide analyte at m/z 67 is also investigated, and can be corrected by using a standard mathematical correction equation. The results of this study further increase the utility of RC-ICP-MS analytical techniques for complex environmental matrices.     

高效液相色谱-电感耦合等离子体质谱联用测定海洋产品中无机砷

采用高效液相色谱( HPLC)和电感耦合等离子体质谱(ICP-MS)联用技术测定了海洋产品中的无机砷.动物性和植物性海洋产品试样经过10％ H3PO溶液(V/V)提取,阴离子交换色谱分离,ICP-MS测定其中As(Ⅲ)和As(Ⅴ)的含量.实验结果表明As(Ⅲ)和As(Ⅴ)的检出限分别为5.0和8.0 μg/kg,线性范...     

Determination of arsenic in gold by flow injection inductively coupled plasma mass spectrometry with matrix removal by reductive precipitation

Arsenic was determined in gold by flow injection hydride generation inductively coupled plasma-mass spectrometry following a batch mode reductive precipitation removal of the interfering gold matrix. A solution of potassium iodide, L-ascorbic acid, and hydrochloric acid was used as the reluctant. The recovery of gold by precipitation and filtration was 99 ± 3%. The detection limit for arsenic in gold was 55 ng g⁻¹ in the solid. The concentration of arsenic that was determined in the Royal Canadian Mint gold sample FAU-10 was 29.7 μg g⁻¹ in the solid; this value was indistinguishable, with 95% confidence, from values determined at the Royal Canadian Mint by graphite furnace atomic absorption spectrometry and by inductively coupled plasma-mass spectrometry. The standard deviation for four replicate determinations of the arsenic in FAU-10 was 0.972 μg g⁻¹ in the solid.     

Particle sample introduction system for inductively coupled plasma–atomic emission spectrometry

Development and characterization of a new, relatively inexpensive, computer-controlled, particle sample introduction (PSI) system for programmable delivery of small amounts of diluted powdered samples into an inductively coupled plasma (ICP) and measurement by atomic emission spectrometry (AES) is described. The PSI was developed for use with non-hygroscopic particles, in particular those with a particle weight in the ng range (i.e., with a diameter in low μm-range) and for solids that can be converted to a powder (i.e., a collection of particles). In this first report on PSI–ICP–AES, linearity of calibration curves and plasma loading concerns were addressed using three modes of operation. In the first mode, the PSI operated similar to a nebulizer and it delivered to the plasma for a period of 5–10 s a relatively constant amount of particles diluted with graphite. In the second mode, the PSI delivered to the plasma a small “puff” of a diluted sample, thus generating a transient, time-domain signal with duration of about a second. In the third mode, an even smaller “puff” was delivered to the plasma and, using high-speed data acquisition (in the kHz range), time-resolved emission signals from individual, μm-diameter and ng-weight particles were observed. Thus, the PSI can also be thought of as a nano-particle (i.e., ng rather than nm) sample introduction system. Similarly, the high-speed, wide-bandwidth single-channel time-resolved data acquisition mode enabled the determination of particle-size distribution. In addition, a dual-channel (or dual-element) mode enabled homogeneity studies on a per-individual-particle basis. In all modes, linear calibration curves were obtained (provided that plasma loading was avoided). Per-cent relative standard deviation ranged between 3.1% and 4.2% for Ni in certified reference materials but was as high as 50% for heterogeneous soil samples. Tungsten emission signals from refractory tungsten carbide powders were enhanced using mixed gases and by modifying the chemical environment of the ICP using SF₆. Furthermore, when coupled with high-speed data acquisition, PSI brought unique capabilities to ICP–AES for homogeneity studies from individual ng-weight particles and for the determination of particle size distributions. Overall, it was concluded that PSI is an attractive alternative to powder sample introduction systems described in the literature.     

Speciation of arsenic by ion chromatography inductively coupled plasma mass spectrometry using ammonium eluents

A method based on ion chromatography (IC) and inductively coupled plasma MS (ICP-MS) was developed for the speciation of arsenic in water and soil extracts. An anion-exchange column (G3154A/101) was used to separate As(III), As(V), dimethylarsinic acid (DMA), and monomethylarsonic acid (MMA) with excellent resolution. Various ammonium salts, including NH4H2PO4, (NH4)2HPO4, (NH4)2CO3, and NH4HCO3, were examined as eluents to reduce matrix interference from chloride and to solve clogging problems. The best arsenic speciation was obtained within 9 min with excellent resolution and without interference from high chloride concentrations using an eluent containing 7.5 mM (NH4)2HPO4 at pH 7.9. The detection limits for the target arsenic species ranged from 0.1 to 0.4 microg/L with direct injection of sample without matrix elimination. The proposed method was effectively demonstrated by determining arsenic species in contaminated waters and soils of Bangladesh.     

Determination of Cu, Mn, Ni and Sn in gasoline by electrothermal vaporization inductively coupled plasma mass spectrometry, and emulsion sample introduction

Trace metals in fuels, except in the case of additives, are usually undesirable and normally they occur in very low concentrations in gasoline, requiring sensitive techniques for their determination. Coupling of electrothermal vaporization with inductively coupled plasma mass spectrometry minimizes the problems related to the introduction of organic solvents into the plasma. Furthermore, sample preparation as oil-in-water emulsions reduces problems related to gasoline analysis. In this work, a method for determination of Cu, Mn, Ni and Sn in gasoline is proposed. Samples were prepared by forming a 10-fold diluted emulsion with a surfactant (Triton X-100), after treatment with concentrated HNO₃. The sample emulsion was pre-concentrated in the graphite tube by repeated pipetting and drying. External calibration was used with aqueous standards in a purified gasoline emulsion. Six samples from different gas stations were analyzed, and the analyte concentrations were found to be in the μg l⁻¹ range or below. The limits of detection were 0.22, 0.02, 0.38 and 0.03 μg l⁻¹ for Cu, Mn, Ni and Sn, respectively. The accuracy of the method was estimated using a recovery test.     

Evaluation of different sample introduction approaches for the determination of boron in unalloyed steels by inductively coupled plasma mass spectrometry

An extended study of different sampling introduction approaches using inductively coupled plasma mass spectrometry (ICP-MS) is presented for the determination of boron in steel samples. The following systems for sample introduction were applied: direct sample solution nebulization by continuous nebulization (CN) using a cross-flow nebulizer and with flow injection (FI), applied to 0.1% (m/v) and 0.5% (m/v) sample solutions, respectively; FI after iron matrix extraction, using acetylacetone–chloroform, and isotopic dilution (ID) analysis as the calibration method; FI with on-line electrolytic matrix separation; and spark ablation (SA) and laser ablation (LA) as solid sampling techniques. External calibration with matrix-matching samples was used with CN, SA, and LA, and only acid solutions (without matrix matching) with FI methods. When FI was directly applied to a sample solution, the detection limit was of 0.15 μg g⁻¹, improving by a factor of 4 that was obtained from the CN measurements. Isotopic dilution analysis, after matrix removal by solvent extraction, made it possible to analyse boron with a detection limit of 0.02 μg g⁻¹ and, with the on-line electrolytic process, the detection limit was of 0.05 μg g⁻¹. The precision for concentrations above 10 times the detection limit was better than 2% for CN, as well as for FI methods. Spark and laser ablation sampling systems, avoiding digestion and sample preparation procedures, provided detection limits at the μg g⁻¹ levels, with RSD values better than 6% in both cases. Certified Reference Materials with B contents in the range 0.5–118 μg g⁻¹ were used for validation, finding a good agreement between certified and calculated values.     

电感耦合等离子体质谱(ICP-MS)法测定锆钛矿中的铪

锆钛矿组成成分复杂,存在耐高温的锆、钛化合物,不易分解,且铪以类质同象进入锆矿物,导致锆钛矿中的铪含量不均,因此完全分解锆钛矿并准确测定其中含量不同的铪成为一个难题。本文建立了碳酸钠-硼砂高温熔融,以178Hf为分析同位素及50 ng/mL185Re为内标,使用电感耦合等离子体质谱法（ICP-MS）测定锆钛矿中铪的新方法,可准确锆钛矿中含量不均的铪。实验研究了锆钛矿成分及其熔融方法,结果表明碳酸钠-硼砂高温熔融效果最好,可完全溶解耐高温难分解的锆钛矿,当碳酸钠-硼砂质量配比为2:1时熔融效果最佳。电感耦合等离子体质谱法具有检出限低、灵敏度高、线性范围宽等优势,可用于测定锆钛矿中含量不均的铪,ICP-MS蠕动泵转速为45 rpm、雾化流量为1.06 L/min时雾化效率最优。在选定的实验条件下,HfO2质谱强度与其质量浓度在0.01～250 ng/mL范围内呈良好的线性关系,相关系数为0.9997,背景等效浓度为0.029 ng/mL,方法检出限为0.0032 ng/mL。按实验方法对中国国家标准物质中的HfO2进行测定,测定值与认定值一致,相对标准偏差在1.6%~3.2%之间。按实验方法对锆钛矿样品中的HfO2进行测定并进行加标回收率实验,测定结果的相对标准偏差（RSDs,n=9）在0.9～3.4%之间,加标回收率在96%～106%之间,满足国家地质矿产行业标准DZ/T 0130—2006的要求。