Studies on two-phase cross flow. Part I: Flow characteristics around a cylinder

A two-phase flow around a body has scarcely been studied until now, though the flow is used in many industrial components. The cross flows around a spacer in a fuel assembly of light water reactors (LWR) and tube supports in a steam generator are closely related to the long-term reliability and the safety. The present study has been planned to clarify the two-phase flow and heat transfer characteristics around a body including the unknown complicated flow behavior. In the first report, the flow characteristics near and behind a cylinder which was located in a vertical upward air-water bubbly flow were investigated. From the observation of the flow patterns and the measurements of the distributions of void fraction, liquid velocity and static pressure, it is revealed that the vortex flow and the change of the static pressure and liquid velocity distribution around the cylinder resulted in the large distortion of the void fraction distribution around the cylinder. The most noticeable phenomena in the wake were that the peaks of the local void fraction appeared in the vicinity of the cylinder surface near the separation point and in the wake behind the cylinder.     

Liquid flow in a gap between a cylinder and a wall in motion

The results of an experimental investigation and calculations of the location of the minimum pressure point are presented for the case, when a cylindrical body moves along a wall in the presence of a small gap. The pressure on the cylindrical body surface is measured in the confusor and diffuser regions. It is shown that with decrease in the gap the minimum pressure point is displaced toward the minimum gap line, with increase in the pressure drop. An increase in the velocity of the motion at a constant gap leads only to a pressure increase in the diffuser region, while the location of the minimum pressure point remains the same. It is established that an increase in the inner cylinder radius moves the minimum pressure location away from the minimum gap line. The formation of two return flow regions in the confusor and diffuser regions near the cylindrical surface is detected. It is shown that the return flow in the pressure drop region reaches the stage of incipient cavitation bubbles. The results obtained can be useful in lubrication theory, as well as in medicine and biology.     

Heat transfer and flow around a circular cylinder with tripping-wires

An experimental study was conducted on the heat transfer under the condition of constant heat flux and the flow around a circular cylinder with tripping-wires, which were affixed at ± 65° from the forward stagnation point on the cylinder surface. The testing fluid was air and the Reynolds number Red, based on the cylinder diameter, ranged from 1.2 × 10⁴ to 5.2×10⁴. Especially investigated are the interactions between the heat transfer and the flow in the critical flow state, in relation to the static pressure distribution along the cylinder surface and the mean and turbulent fluctuating velocities in the wake. It is found that the heat transfer from the cylinder to the cross flow is in very close connection with the width of near wake.     

Application of Differing Forcing Function Models on Simulated Flow Past an Oscillating Cylinder in a Uniform Low Reynolds Number Flow

A Computational Fluid Dynamics (CFD) model is presented for the uniform viscous two dimensional flow past an oscillating cylinder at low Reynolds number. Numerical simulations are made to study the effect of differing forced induced oscillation mechanisms with a large range of cylinder forcing frequencies. In the first case sinusoidal velocity slip boundary conditions are adopted for the cylinder surface to simulate cylinder oscillation. The implication suggests that no modification or additional term need to be added to the Navier-Stokes equations. In the second case this time extra body force terms which are assumed to account for velocity effects due to cylinder movement are included in the Navier-Stokes equations with the imposition of same boundary conditions. Drag and lift coefficients are extracted from present numerical results and other detailed computations of these coefficients are made at a Reynolds number of 80 and an amplitude-to diameter ratio 0.14. The results are found to be in agreement with each other at low force driving frequencies below and near lock-in. However, differences are found at higher frequencies above lock-in. Agreement are also found with experimental results at some frequency ranges.     

流体边界层上电磁力的控制效应研究

利用作用于流体边界层上的电磁体积力改变流体边界层的结构，研究电磁力对流场的控制 作用效果. 电极与磁极交替分布的电磁场激活板包覆在圆柱体表面置于流动的电解质溶液 中，产生的电磁力沿圆柱体表面分布，可以改变流体边界层的结构，从而实现对流场的控制. 用电磁屏蔽和时域控制的方法调整电磁力的时空分布参数，圆柱绕流分离点可以在前驻点和 后驻点之间变动，产生不同的控制效果. 流体边界层上的电磁力能连续控制圆柱绕流、尾流 涡街的形态. 正向电磁力具有较好的消涡、减震和减阻控制效应. 反向电磁力具有明显的增 涡控制效应，具有较强的制动控制效应，此时圆柱体表面涡量分布的对称性和稳定性被破坏.     

圆柱表面包覆电磁场消涡与增涡实验研究

利用电磁体积力改变流体边界层的结构，用作用于流体边界层上的电磁力进行消涡与增涡控制。交替分布的电极和磁极包覆在圆柱体的表面置于电介质溶液中，简单调整电磁力的时间与空间分布可以方便地控制圆柱绕流的形态。通过理论分析和数值模拟确定了实验控制的关键参数，实现了电磁力消涡和增涡的连续控制，电磁力作用下的圆柱绕流的分离点可以在前驻点和后驻点之间变动。     

基于定常吹吸气的波浪型圆柱主动控制研究

基于定常吹吸气对波浪型圆柱近尾迹流动进行控制以增强柱体振动, 采用大涡模拟研究了亚临界雷诺数(Re = 3000)下前吹后吸和前后吸气控制方式在不同吹吸气工况对波浪型圆柱升阻力特性、时均压力系数、环量、湍动能及近尾迹流动结构的影响. 研究发现: 前吹后吸和前后吸气控制下波浪型圆柱在不同吹吸气动量系数工况脉动升力系数均显著提高, 最大较未受控直圆柱和波浪型圆柱分别提升高达636%和391%, 这主要可能归因于吹吸气控制使波浪型圆柱回流区变短, 高强度涡集中向钝体后方靠拢, 旋涡形成长度缩短, 展向涡流与顺流向涡流相互作用在波浪型圆柱下游形成的“肋状涡”变大变长, 近尾迹环量显著增大, 从而导致脉动升力系数增大, 这可能将诱导柱体产生更强的振动; 同时两种控制方式均改变了波浪型圆柱表面的压力分布, 由于在波浪型圆柱前驻点吹气使前端趋于流线型, 前吹后吸在不同吹吸气动量系数下波浪型圆柱的高压区减小, 但在后驻点吸气使得低压区增大, 而前后吸气在不同吹吸气动量系数下波浪型圆柱的高压区基本不变, 低压区增大. 研究结果可为低风速地区分布式风力俘能结构俘能效率提升提供基础理论支持.      

Boundary layer on the moving surface of a cylinder

A study is made of the problem of the boundary layer on a cylinder with a moving surface when the cylinder moves with constant velocity in an incompressible fluid. Expressions are obtained for the distributions of the frictional stress on the surface of the cylinder and the coordinate of the singular point in the solution of the boundary layer equations that indicates the appearance of a region of reverse flow for different values of the relative velocity of the motion of the surface of the cylinder. Numerical calculations have been made of the work of the force of friction associated with displacement of the cylinder, the work expended on the motion of its surface, and, in the case of flow separation, the work of the pressure forces (it being assumed here that the pressure and friction on the wall behind the singular point are constant and equal to the pressure and friction at the singular point).     

A ghost-cell immersed boundary method for large eddy simulation of flows in complex geometries

An efficient ghost-cell immersed boundary (IB) method is proposed for large eddy simulations of three-dimensional incompressible flow in complex geometries. In the framework of finite volume method, the Navier–Stokes equations are integrated using an explicit time advancement scheme on a collocated mesh. Since the IB method is known to generate an unphysical velocity field inside the IB that violates the mass conservation of the cells near the IB, a new IB treatment is devised to eliminate the unphysical velocity generated near the IB and to improve the pressure distribution on the body surface. To validate the proposed method, both laminar and turbulent flow cases are presented. In particular, large eddy simulations were performed to simulate the turbulent flows over a circular cylinder and a sphere at subcritical Reynolds numbers. The computed results show good agreements with the published numerical and experimental data.     

Flow around a porous cylinder subject to continuous suction or blowing

In the present experimental investigation the surface pressure distribution, vortex shedding frequency, and the wake flow behind a porous circular cylinder are studied when continuous suction or blowing is applied through the cylinder walls. It is found that even moderate levels of suction/blowing (5% of the oncoming streamwise velocity) have a large impact on the flow around the cylinder. Suction delays separation contributing to a narrower wake width, and a corresponding reduction of drag, whereas blowing shows the opposite behaviour. Both uniform suction and blowing display unexpected flow features which are analysed in detail. Suction shows a decrease of the turbulence intensity throughout the whole wake when compared with the natural case, whilst blowing only shows an effect up to five diameters downstream of the cylinder. The drag on the cylinder is shown to increase linearly with the blowing rate, whereas for suction there is a drastic decrease at a specific suction rate. This is shown to be an effect of the separation point moving towards the rear part of the cylinder, similar to what happens when transition to turbulence occurs in the boundary layer on a solid cylinder. The suction/blowing rate can empirically be represented by an effective Reynolds number for the solid cylinder, and an analytical expression for this Reynolds number representation is proposed and verified. Flow visualizations expose the complexity of the flow field in the near wake of the cylinder, and image averaging enables the retrieval of quantitative information, such as the vortex formation length.     

Control of the near-wake flow around a circular cylinder with electrohydrodynamic actuators

We analysed the modifications of the near wake of a circular cylinder (2,300< Re <58,000) when the flow was perturbed steadily using an electrohydrodynamic actuator. Two electrodes flush-mounted on the surface of the cylinder were excited with DC power supplies to create a plasma sheet contouring the body. The discharge produced an electric force and changed the physical properties in the fluid layers at close vicinity to the surface. This plasma sheet diminished the base pressure, modified the size of the mean recirculation region and produced an increase in the shear stresses of the layers bounding the contour of this region.     

Influence of viscosity on the flow over the sharp edge of bodies consisting of a spherical segment joined to an inverted cone

The results are given of an experimental investigation of the supersonic axisymmetric flow over a body consisting of a spherical segment joined to an inverted cone in the neighborhood of the point of inflection of the profile (Fig. 1a). For the limiting case of a cylinder with a flat end and M = 3, a study was made of the influence of the Reynolds number and the state of the boundary layer on the parameters of the local separation region formed near the inflection (Fig. 1b). It was found that there is an appreciable decrease in the length of the separation region and the pressure in it when the Reynolds number increases in the range Re = 10⁵– 10⁷ in the case of a laminar boundary layer on the flat end near the inflection point. A low level of the pressure on the surface of the body was achieved — of the order of thousandths of the pressure behind a normal shock. There was found to be a sharp increase in the pressure in the separation region when the boundary layer on the end becomes turbulent with transition to a flow regime that is self-similar with respect to the Reynolds number. Under conditions of a turbulent boundary layer, systematic experimental data on the pressure on the inverted cone near the point of inflection of such bodies were obtained and generalized.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 154–157, January–February, 1981.     

Flow field determination on the surface of some bodies in an incompressible fluid stream

Simple relationships of local type are established for the velocity and pressure distributions on the surface of an elliptical cylinder, an ellipsoid of revolution, and an arbitrary triaxial ellipsoid in an incompressible fluid stream. It is shown that in an exact formulation the flow parameters at a given point of the body surface depend only on the local angle of stream impact with a surface element. In particular, Newtonian impact theory, which is used extensively in hypersonic gas flow computations, turns out to be valid for the velocity distribution.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 187–190, March–April, 1976.The author is grateful to G. Yu. Stepanov and A. G. Petrov for useful discussions of this paper.     

VORTEX SHEDDING RESONANCE FROM A ROTATIONALLY OSCILLATING CYLINDER

Vortex shedding resonance of a circular cylinder wake to a forced rotational oscillation has been investigated experimentally by measuring the velocity fluctuations in the wake, pressure distributions over the cylinder surface, and visualizing the flow field with respect to cylinder oscillations. The vortex shedding resonance occurs near the natural shedding frequency at small amplitude of cylinder oscillations, while the peak resonance frequency shifts to a lower value with an increase in oscillation amplitude. The drag and lift forces acting on the cylinder at fixed forcing Strouhal number indicate that the phase lag of fluid forces to the cylinder oscillations increases with an increase in oscillation amplitude, supporting the variation of resonance frequency with oscillation amplitude. The comparative study of the measured pressure distributions and the simultaneous flow visualizations with respect to cylinder rotation shows the mechanisms of phase lag, which is due to the strengthened vortex formation and the modification of the surface pressure distributions.     

Supersonic low-concentration dusty-gas flow past a plane cylinder in the presence of an oblique shock wave interacting with the bow shock

The motion of an inertial dispersed admixture near a plane cylinder immersed in a steady-state hypersonic dusty flow in the presence of an oblique shock wave interacting with the bow shock is considered. It is assumed that the free-stream particle mass concentration is small and the particles do not affect the carrier flow. The III and IV shock wave interaction regimes are considered. The gas flow parameters in the shock layer are calculated from the numerical solution of the full Navier-Stokes equations for the perfect gas. A TVD second-order finite-difference scheme constructed on the basis of a finite volume method is used. For calculating the dispersed-phase parameters, including the concentration, the full Lagrangian method is used. On a wide range of variation of the particle inertia parameters, the patterns of the particle trajectories, velocity, concentration, and temperature in the shock layer are studied. The possibility of aerodynamic focusing of the particles behind the shock wave intersection point and the formation of narrow beams with a high particle concentration is revealed. These beams impinge on the cylinder surface and result in a sharp increase in the local heat fluxes. The maximal possible increase in the heat fluxes caused by the particles colliding with the cylinder surface is estimated for the flows with and without the incident oblique shock wave.     

Forced Convection Heat Transfer from a Finite-Height Cylinder

This paper presents a large eddy simulation of forced convection heat transfer in the flow around a surface-mounted finite-height circular cylinder. The study was carried out for a cylinder with height-to-diameter ratio of 2.5, a Reynolds number based on the cylinder diameter of 44 000 and a Prandtl number of 1. Only the surface of the cylinder is heated while the bottom wall and the inflow are kept at a lower fixed temperature. The approach flow boundary layer had a thickness of about 10% of the cylinder height. Local and averaged heat transfer coefficients are presented. The heat transfer coefficient is strongly affected by the free-end of the cylinder. As a result of the flow over the top being downwashed behind the cylinder, a vortex-shedding process does not occur in the upper part, leading to a lower value of the local heat transfer coefficient in that region. In the lower region, vortex-shedding takes place leading to higher values of the local heat transfer coefficient. The circumferentially averaged heat transfer coefficient is 20 % higher near the ground than near the top of the cylinder. The spreading and dilution of the mean temperature field in the wake of the cylinder are also discussed.     

Cavitation deceleration of a circular cylinder in a liquid after impact

The formation of a cavity during vertical impact and subsequent deceleration of a circular cylinder semi-immersed in a liquid is investigated. The problem with unilateral constraints is formulated to determine the initial regions of separation and contact of liquid particles and the perturbations of the inner and outer free boundaries of the liquid at small times. The problem is solved using a direct asymptotic method which is effective at small times. Examples of numerical calculations of the formation of one or two cavities near the boundary of the body are given. It is shown that the acceleration of the cylinder has a significant effect on the liquid flow pattern near the body at small times.     

Flow around a cylinder at the beginning of the critical region

Results of experiments with a turbulent flow around a transversely aligned circular cylinder located at identical distances from the walls of a rectangular channel are reported. Data on averaged velocity fields around the cylinder are obtained by means of particle image velocimetry (PIV). Based on these fields, the near wake behind the cylinder is studied, and the kinematic characteristics for flow regimes with and without cavitation are compared. Based on the vector fields of averaged velocity, the angles of separation of the boundary layer from the cylinder surface in the considered flow regimes are determined. The drag coefficients of the cylinder for different flow regimes are calculated. It is demonstrated that the vortex region behind the cylinder and the drag coefficient of the cylinder increase in the case with cavitation. It is also shown that vortex shedding from the cylinder may be irregular, despite the fact that this process is quasi-periodic for most of the time.     

Radial variation of adiabatic and diabatic spiral vortex flow in a wide annular gap

Transitions occurring after the onset of spiral vortex flow in a wide concentric annular gap of radius ratio 0.8, formed by a stationary outer cylinder and a rotatable inner cylinder, have been studied experimentally. By isothermal heating of the annular surface, it was possible to consider diabatic as well as adiabatic conditions. At an axial Reynolds number of 500 and for a range of Taylor numbers up to 10⁷, power spectra and auto-correlograms were taken at two radial positions near to the inner and outer annular surfaces; these are compared with previous results taken at mid-gap under adiabatic conditions. Measurements of turbulence intensity across the gap were made also. Probability histograms and signal traces for diabatic flow near to the outer annular surface are presented. It has been shown that the vortex transitions affect the thermal boundary layer and, consequently, the heat transfer rates at the outer surface. A positive radial thermal gradient was seen to have little effect on the flow. The imposed axial flow was shown to be stabilising under adiabatic conditions but destabilising under diabatic conditions.     

Near-wake flow structure of elliptic cylinders close to a free surface: effect of cylinder aspect ratio

The flow fields behind elliptic cylinders adjacent to a free surface were investigated experimentally in a circulating water channel. A range of cylinder aspect ratios (AR=2, 3, 4) were considered, while the cross-sectional area of the elliptical cylinder was kept constant. The main objective of this study was to investigate the effect of cylinder aspect ratio and a free surface on the flow structure in the near-wake behind elliptic cylinders. For each elliptic cylinder, the flow structure was analyzed for various values of the submergence depth of the cylinder beneath the free surface. The flow fields were measured using a single-frame double-exposure PIV (Particle Image Velocimetry) system. For each experimental condition, 350 instantaneous velocity fields were obtained and ensemble-averaged to obtain the mean velocity field and spatial distribution of the mean vorticity statistics. The results show that near-wake can be classified into three typical flow patterns: formation of a Coanda flow, generation of substantial jet-like flow, and attachment of this jet flow to the free surface. The general flow structure observed behind the elliptic cylinders resembles the structure previously reported for a circular cylinder submerged near a free surface. However, the wake width and the angle of downward deflection of the shear layer developed from the lower surface of the elliptic cylinder differ from those observed for a circular cylinder. These trends are enhanced as cylinder aspect ratio is increased. In addition, the free surface distortion is also discussed in the paper.