直流磁控溅射制备氧化钒薄膜

讨论了在低温下以高纯金属钒作靶材,用直流磁控溅射的方法制备出了氧化钒薄膜。通过设计正交试验,分析了氩气和氧气的流量比,溅射功率,工作压强,基底温度对氧化钒薄膜沉积速率和电阻温度系数TCR的影响,采用RTP-500型快速热处理机对氧化钒薄膜样品进行了退火热处理,实验结果表明:当Ar与O2的比例为100:4,溅射功率为120W,工作压强为2Pa时,所获得薄膜TCR较大,都在-2%/K附近,最高的可达-3.6%/K。     

射频磁控溅射制备氧化钒薄膜的研究

氧化钒（VOx）薄膜是一种广泛应用于红外热成像探测的薄膜材料,研究VOx薄膜的制备工艺、获取高电阻温度系数（TCR）的VOx薄膜具有重要意义。以高纯金属钒作靶材,采用射频磁控溅射的方法在室温下制备了VOx薄膜。主要研究了氩氧流量比以及功率等工艺参数对薄膜TCR的影响,获得了较好的工艺参数。采用万用表和X射线光电子能谱仪（XPS）分别测试了不同条件下射频磁控溅射法制备的VOx薄膜的电阻特性和薄膜成分,测试结果表明,采用所获得的较好工艺参数制备的VOx薄膜TCR值大于1.8%。     

快速热处理制备相变氧化钒薄膜及其特性研究

采用直流对靶磁控溅射在Si<100>基底上沉积金属V薄膜, 然后分别在纯氧气环境和纯氮气环境下进行快速热处理制备具有 金属-半导体相变特性的氧化钒(VO_X)薄膜, 热处理条件分别为纯氧气环境下430℃/40 s, 450℃/40 s, 470℃/40 s, 450℃/30 s, 450℃/50 s, 纯氮气环境下500℃/15 s. 用X射线衍射仪、X射线光电子能谱、原子力显微镜 和扫描电子显微镜对薄膜的结晶结构、钒的价态和组分以及微观形貌进行分析. 利用四探针薄膜电阻测量方法和THz时域频谱技术分析薄膜的电学特性和光学特性. 结果表明: 金属V薄膜经过纯氧气环境450℃/40 s快速热处理 后形成了具有低相变特性的VO_X薄膜, 升温前后薄膜方块电阻变化幅度达到两个数量级, THz透射强度变化幅度较小. 为了提高薄膜的相变特性, 对制备的VO_X薄膜采用纯氮气环境500℃/15 s快速热处理, 薄膜的相变特性有了明显提升, 相变前后方块电阻变化达到3个数量级, THz透射强度变化达到56.33%.     

功率密度对中频磁控溅射制备 AZO薄膜性能的影向

利用中频磁控溅射法在普通玻璃衬底上沉积掺铝氧化锌(ZnO ∶ Al,简称AZO)薄膜,通过调整溅射功率密度参数得到沉积速率与功率密度之间的关系,制备了不同厚度的AZO薄膜.利用台阶仪、XRD、XPS、紫外可见分光光度计和Hall测试系统等方法研究了功率密度与厚度对AZO薄膜结构、组分、光学和电学性能的影响.实验结果表明...     

NiTi合金薄膜厚度对相变温度影响的X射线光电子能谱分析

采用X射线衍射和X射线光电子能谱实验手段对不同厚度的NiTi薄膜相变温度的变化进行了分析.结果表明在相同衬底温度和退火条件下,3?μm厚度的薄膜晶化温度高于18?μm厚度的薄膜.衬底温度越高,薄膜越易晶化,退火后薄膜奥氏体相转变温度As越低.薄膜的表面有TiO₂氧化层形成,氧化层阻止了Ni原子渗出;膜与基片的界面存在Ti₂O₃和NiO.由于表面和界面氧化层的存在,不同厚度的薄膜内层的厚度也不同,因而薄膜越薄,Ni原子的含量就越高.Ni原子的含量的不同会影响薄膜的相变温度. 关键词： NiTi合金薄膜 X射线衍射 相变 X射线光电子能谱     

溅射功率对碳化硼薄膜组分与力学性能的影响

采用射频磁控溅射技术,在不同溅射功率条件下制备了碳化硼薄膜,并用X射线光电子能谱(XPS)和傅里叶变换红外吸收光谱(FT-IR)对碳化硼薄膜的组分进行了定量表征,分析了功率变化对碳化硼组分的影响。利用纳米压入仪通过连续刚度法(CSM)对碳化硼薄膜的硬度和模量等力学性能进行了分析。研究表明:随着功率的增大,硼与碳更易结合形成BC键,在功率增大到250 W时,BC键明显增多;在250 W时,硼与碳的原子分数比出现了最大值5.66;碳化硼薄膜的硬度与模量都随功率的增大呈现出先增大后减小的趋势,且在250 W时均出现了最大值,分别为28.22 GPa和314.62 GPa。     

溅射功率对碳化硼薄膜组分与力学性能的影响

采用射频磁控溅射技术,在不同溅射功率条件下制备了碳化硼薄膜,并用X射线光电子能谱(XPS)和傅里叶变换红外吸收光谱(FT-IR)对碳化硼薄膜的组分进行了定量表征,分析了功率变化对碳化硼组分的影响。利用纳米压入仪通过连续刚度法(CSM)对碳化硼薄膜的硬度和模量等力学性能进行了分析。研究表明：随着功率的增大,硼与碳更易结合形成BC键,在功率增大到250 W时,BC键明显增多;在250 W时,硼与碳的原子分数比出现了最大值5.66;碳化硼薄膜的硬度与模量都随功率的增大呈现出先增大后减小的趋势,且在250 W时均出现了最大值,分别为28.22 GPa和314.62 GPa。     

Vanadium oxide thin films deposited on indium tin oxide glass by radio—frequency magnetron sputtering

Highly oriented VO₂(B), VO₂(B) + V₆O₁₃ films were grown on indium tin oxide glass by radio-frequency magnetron sputtering. Single phase V₆O₁₃ films were obtained from VO₂(B) +V₆O₁₃ films by annealing at 480℃ in vacuum. The vanadium oxide films were characterized by x-ray diffraction and x-ray photoelectron spectra (XPS). It was found that the formation of vanadium oxide films was affected by substrate temperature and annealing time, because high substrate temperature and annealing were favourable to further oxidation. Therefore, the formation of high valance vanadium oxide films was realized. The V₆O₁₃ crystalline sizes become smaller with the increase of annealing time. XPS analysis revealed that the energy position for all the samples was almost constant, but the broadening of the V_2p3/2 line of the annealed sample was due to the smaller crystal size of V₆O₁₃.     

氧化钒薄膜微观结构的研究

采用直流磁控反应溅射在Si(100)衬底上溅射得到(001)取向的V₂O₅薄膜.x射线衍射(XRD)、扫描电镜(SEM)和傅里叶变换红外光谱(FTIR)的结果表明，氧分压影响薄膜的成分和生长取向，在氧分压0.4Pa时溅射得到(001)取向的纳米V₂O₅薄膜，即沿c轴垂直衬底方向取向生长的薄膜.V₂O₅薄膜经过真空退火得到(001)取向的VO₂薄膜，晶体颗 关键词： 微观结构 氧化钒薄膜 择优取向 直流磁控溅射     

沉积态铀薄膜表面氧化的X射线光电子能谱

含铀(U)薄膜在激光惯性约束聚变的实验研究中有重要的用途.研究其在不同气氛下的氧化性能可以为微靶制备、储存及物理实验提供关键的实验数据.通过超高真空磁控溅射技术制备了纯U薄膜及金-铀(Au-U)复合平面膜,将其在大气、高纯氩(Ar)气及超高真空度环境中暴露一段时间后,利用X射线光电子能谱仪结合Ar~+束深度剖析技术考察U层中氧(O)元素分布及价态,分析氧化产物及机理.结果显示,初始状态的U薄膜中未检测到O的存在.Au-U复合薄膜中的微观缺陷减弱了Au防护层的屏蔽效果,使其在3周左右时间内严重氧化,产物为U表面致密的氧化膜及缺陷周围的点状腐蚀物,主要成分均为二氧化铀(UO_2).在高纯Ar气中纯U薄膜仅暴露6 h后表面即被严重氧化,生成厚度不均匀的UO_2.在超高真空度环境下保存12 h后,纯U薄膜表面也发生明显氧化,生成厚度不足1 nm的UO_2.Ar~+束对铀氧化物的刻蚀会因择优溅射效应而使UO_2被还原成非化学计量的UO_(2-x),但这种效应受O含量的影响.     

Study of nanocrystalline VO2 thin films prepared by magnetron sputtering and post-oxidation

Nanocrystalline VO2 thin films were deposited onto glass slides by direct current magnetron sputtering and postoxidation. These films undergo semiconductor-metal transition at 70°C, accompanied by a resistance drop of two magnitude orders. The crystal structures and surface morphologies of the VO2 films were characterized by x-ray diffraction (XRD) and atomic force microscope (AFM), respectively. Results reveal that the average grain size of VO2 nanograins measured by XRD is smaller than those measured by AFM. In addition, Raman characterization indicates that stoichiometric VO2 and oxygen-rich VO2 phases coexist in the films, which is supported by x-ray photoelectron spectroscopy (XPS) results. Finally, the optical properties of the VO2 films in UV-visible range were also evaluated. The optical band gap corresponding to 2p-3d inter-band transition was deduced according to the transmission and reflection spectra. And the deduced value, E opt2p-3d = 1.81 eV, is in good agreement with that previously obtained by theoretical calculation.     

Crystallization and electrical properties of V2O5 thin films prepared by RF sputtering

V₂O₅ thin films were prepared under various conditions by using reactive RF sputtering technique. The microstructure and electrical properties of the films are have been investigated. X-ray diffraction data revealed the films deposited at low O₂/Ar ratio are amorphous. The orthorhombic structure of film improved after post annealing at 873 K. The microstructure parameters (crystallite/domain size and macrostrain) have been evaluated by using a single order Voigt profile method. Using the two-point probe technique, the dark conductivity as a function of the condition parameters such as film thickness, oxygen content and temperature are discussed. It was also found that, the behaviour of ρd versus d was found to fit properly with the Fuchs-Sondheimer relation with the parameters: ρ_o = 2.14 × 10⁷ Ω cm and ?_o = 112 ± 2 nm. At high temperature, the electrical conductivity is dominated by grain boundaries, the values of activation energy and potential barrier height were 0.90 ± 0.02 eV and 0.92 ± 0.02 V, respectively.     

Effects of annealing temperature and method on structural and optical properties of TiO2 films prepared by RF magnetron sputtering at room temperature

TiO₂ thin film was deposited on non-heated Si(1 0 0) substrate by RF magnetron sputtering. The as-deposited films were annealed by a conventional thermal annealing (CTA) and rapid thermal annealing (RTA) at 700 and 800 °C, and the effects of annealing temperature and method on optical properties of studied films were investigated by measuring the optical band gaps and FT-IR spectra. And we also compared the XRD patterns of the studied samples. The as-deposited film showed a mixed structure of anatase and brookite. Only rutile structures were found in samples annealed above 800 °C by CTA, while there are no special peaks except the weak brookite B(2 3 2) peak for the sample annealed at (or above) 800 °C by RTA. FT-IR spectra show the broad peaks due to Ti-O vibration mode in the range of 590-620 cm⁻¹ for the as-deposited film as well as samples annealed by both annealing methods at 700 °C. The studied samples all had the peaks from Si-O vibration mode, which seemed to be due to the reaction between TiO₂ and Si substrate, and the intensities of these peaks increased with increasing of annealing temperature. The optical band gap of the as-deposited film was 3.29 eV but it varied from 3.39 to 3.43 eV as the annealing temperature increased from 700 to 800 °C in the samples annealed by CTA. However, it varied from 3.38 to 3.32 eV as the annealing temperature increased from 700 to 800 °C by RTA.     

Dependence of substrate temperature of Zn0.8Co0.2O films deposited by pulsed DC magnetron sputtering

We have investigated the microstructure, electrical and magnetic properties of the ZnCoO thin films, which were prepared by the asymmetrical bipolar-pulsed DC magnetron sputtering as a function of substrate temperature. The structural properties of ZnCoO films were characterized with a high resolution XRD. The XRD patterns of the ZnCoO films showed a strong (0 0 2) preferential orientation. The average crystallite size was 23–35 nm, which was estimated from full width at half maximum of XRD results. The electrical resistivity of the films were measured by the van der Pauw method through Hall measurement and showed below 10⁻¹ Ω cm above 300 °C. The magnetic properties of the ZnCoO films were analyzed by the alternating gradient magnetometer at room temperature. All of the films were exhibited the ferromagnetic nature. The high conductivity and room temperature ferromagnetism of the ZnCoO films above 300 °C suggested that the possibility for the application to diluted magnetic semiconductors.     

Surface oxidation of vanadium dioxide films prepared by radio frequency magnetron sputtering

This paper reports that the thermochromic vanadium dioxide films were deposited on various transparent substrates by radio frequency magnetron sputtering, and then aged under circumstance for years. Samples were characterized with several different techniques such as x-ray diffraction, x-ray photoelectron spectroscopy, and Raman, when they were fresh from sputter chamber and aged after years, respectively, in order to determine their structure and composition. It finds that a small amount of sodium occurred on the surface of vanadium dioxide films, which was probably due to sodium ion diffusion from soda-lime glass when sputtering was performed at high substrate temperature. It also finds that aging for years significantly affected the nonstoichiometry of vanadium dioxide films, thus inducing much change in Raman modes.     

脉冲磁控溅射法制备单斜相氧化铒涂层

用中频脉冲反应磁控溅射法,在溅射功率为78 W,93 W和124 W以及衬底温度分别为室温,500 ℃及677 ℃下制备了氧化铒涂层.采用原子力显微镜、纳米压痕、X射线衍射和掠入射X射线衍射法研究了涂层的形貌、力学性能及物相结构.测量了涂层的电学性能.结果显示,脉冲磁控溅射沉积氧化铒涂层具有较高的沉积速率.实验制备得到了单斜相结构的氧化铒涂层.提高溅射功率时,沉积速率从28 nm/min增大至68 nm/min,涂层的结晶质量显著下降.提高衬底温度至500 ℃和677 ℃时,单斜相衍射峰强度下降.分析认为 关键词： 氧化铒 脉冲磁控溅射 单斜晶相     

Effect of deposition temperature on the microstructure and surface morphology of c-axis oriented AlN films deposited on sapphire substrate by RF reactive magnetron sputtering

In this paper, c-axis oriented AlN films were prepared on sapphire substrate by RF reactive magnetron sputtering at various deposition temperatures (30–700 °C). The influences of deposition temperature on the chemical composition, crystalline structure and surface morphology of the AlN films were systematically investigated. The as-deposited films were characterized by X-ray photoelectron spectroscopy (XPS), two-dimensional X-ray diffraction (2D-XRD) and atomic force microscopy (AFM). The experimental results show that it can be successfully grown for high-purity and near-stoichiometric (Al/N = 1.12:1) AlN films except for the segregation of a few oxygen impurities exist in the form of Al–O bonding. The chemical composition of as-deposited films is almost independent of substrate temperature in the range of 30–700 °C. However, the crystalline structure and surface morphology of the deposited AlN films are strongly influenced by the deposition temperature. The optimum deposition temperature is 300 °C, giving a good compromise between crystalline structure and surface morphology to grow AlN films.