沉降分布孔隙率多孔介质模型及数值研究

研究沉降分布孔隙率多孔介质流动和传热,根据"O"形圈理论和现场测定确定孔隙率系数,建立坐标方向孔隙率分布函数;考虑流体密度变化,并引入Brinkman-Forchheimer的扩展Darcy模型,能量方程采用界面连续条件,建立沉降分布孔隙率多孔介质流动和传热求解模型.采用差分法对模型进行离散化,应用高斯-赛德尔方法迭代求解.数值分析表明:沉降分布孔隙率条件下多孔介质内流体流动速度在壁面附近较大,中心部位较小,壁面附近孔隙率的增大使得低流速区域减小,较高流速区域增大;当孔隙率小值时,温度按线性减小;当孔隙率大值时,温度在高低温壁面附近迅速减小,在中部减小较缓,热量按导热和对流共同传递;孔隙率增大能使平均怒谢尔数增大,对流换热作用增强.     

泡沫铜填充曲折槽道散热器内对流换热研究

设计了高孔隙率泡沫金属铜填充的曲折槽道散热器,采用去离子水为工作介质,实验研究了单相对流换热时散热器的压降、散热量、热阻等特性.结果表明,流体流过槽道时压降和流速成二次多项式关系;随着受热表面温度升高,散热量变大,热阻减小并趋于定值.相同雷诺数时,Nu数随着表面温度的升高而增大;综合评价散热器的性能发现,该换热器在相同压降时热阻要低于微槽道散热器和平板多孔介质散热器.     

Experimental Investigation of Laminar Heat Transfer Inside Trapezoidal Duct Having Different Corner Angles

In this study, steady-state laminar forced flow and heat transfer in a horizontal smooth trapezoidal duct having different corner angles were experimentally investigated in the Reynolds number range from 10² to 10³. Flow is hydrodynamically fully developed and thermally developing under a uniform surface temperature condition. Based on the present experimental data of laminar flow in the thermal entrance region, new engineering correlations were presented for the heat transfer and friction coefficients for each corner angle. The results have shown that as the Reynolds number increases heat transfer coefficient increases but Darcy friction factor decreases. Also, it is observed that average Nusselt number increases while average Darcy friction factor decreases with increasing corner angle of the duct.     

油基钻屑螺纹推进式换热器流动传热特性

对油基钻屑在螺纹推进式换热器内的流动换热过程进行了数值模拟,研究了螺杆转速、油基钻屑雷诺数Re和螺纹截面形状对流动换热的影响。结果表明:随着螺杆转速增加,传热系数、油基钻屑出口温度均增大;同时发现,当雷诺数Re<250时,壳侧Nusselt数随雷诺数Re增大而迅速增大,此后雷诺数对Nusselt数影响较小;Nusselt数随曲率比d_i/D增大而增大。为方便工程设计,利用数值结果给出了油基钻屑的流动换热关系式。     

波纹内翅片管中对流换热与阻力特性的实验研究

本文研究了空气在一种波纹内翅片管内强制对流的换热与阻力特性,得出了所测参数范围内换热Nusselt数和阻力系数f随Reynolds数变化的实验关联式,并与类似波纹内翅片管的换热效果进行了比较,结果表明波纹内翅片管换热强化的程度与其结构有很大的关系。     

微圆管进口区气体流动与换热特性研究

对微圆管进口区运用一阶速度滑移和温度跳跃边界,考察了Kn、动量调和及热调和系数对流动与换热特性的影响机理和规律.模拟结果表明:流动进口段长度随Kn增加而增加,但随动量调和系数减小而减小;热进口段长度随Kn增加而增加,但随动量调和系数及热调和系数减小而减小;Nu数随Kn增加及热调和系数减小而减小,但随动量调和系数减小而增加.     

不连续冷源布局多孔介质内热流耦合LBM数值模拟

为研究不连续冷源边界对内置发热体多孔介质方腔内传热及流动的影响,采用格子Boltzmann方法对REV尺度下多孔介质方腔内的自然对流进行计算,并研究瑞利数（Ra）、达西数（Da）、孔隙度对多孔介质方腔内传热流动的影响.发现Da对方腔内的流体流型影响很大,Da为10^-4时,多孔介质方腔内只有一个涡流,而Da为10^-2时,方腔内有两个涡流.增大Ra、Da、孔隙度可以提高冷源壁面的平均努赛尔数（Nu）,增强散热效果,孔隙率对平均Nu影响程度和Da的大小有关.当冷源布置在壁面上方,壁面的平均Nu随Ra的增加剧烈变化,方腔处于高Ra条件下时,将冷源布置在边界的上方可以提高散热效果.6种布置方案中Case 6的散热效果最好.     

Experimental studies on natural convection boiling of water in a vertical annulus of a closed-loop thermo-siphon

Experimental studies on natural convection boiling of water in an internally heated narrow vertical annulus, with the liquid circulating through a cold leg forming a closed-loop thermo-siphon, have been carried out. The radius and aspect ratios of the annulus are 1.184 and 352, respectively. The experimental data, which consist of wall and liquid temperatures, liquid and vapor flow rates, and differential pressure across the test section, are recorded on a data logging system. The experiments have been performed for a constant heat flux of 15–35 kW/m² from the startup period until the steady state to study the transient behavior of the system. The boiling and non-boiling zones in the annulus have been identified and presented graphically through the liquid and wall temperatures for the steady state. They have been also verified through the visual photographs of the flow patterns in the annulus. The flow is found to be oscillatory in nature with no particular trend. Although the experimental data seems to be scattered, but when analyzed for a short duration, they are found well within the ±3σ (three sigma). This confirms the quasi-steady-state condition of the system. The steady-state values of Reynolds number and liquid circulation rate come out to be 133.1–453.5 and 7.0–23.87 g/s, respectively, while the Nusselt number and heat transfer coefficient are 7.98–13.57 and 1433.57–2435.35 W/m²K, respectively. Mathematical correlations for liquid mass flow rates, heat transfer coefficient, Reynolds number, and Nusselt number have been developed and compared with the existing correlations, which are in good agreement.     

Experimental Investigation of Transient Forced Convection of Liquid Methane in a Channel at High Heat Flux Conditions

Transient heat transfer of liquid methane under forced convection in a 1.8 mm × 1.8 mm asymmetrically heated square channel was investigated. This study is aimed at understanding the heat transfer behavior of cryogenic propellant in cooling channels of a regeneratively cooled rocket engine at the start-up condition. To simulate high heat load conditions representative of regeneratively cooled rocket engines, a high heat flux test facility with cryogenic liquid handing capabilities was developed at the Center for Space Exploration Technology Research. The time history of inlet and outlet fluid temperatures and test section channel wall temperatures were measured at high heat flux conditions (from 1.19 to 3.80 MW/m²) and a Reynolds number (Re) range of 1.88 × 10⁵ to 3.45 × 10⁵. The measured wall temperature data point toward possible film boiling within the test section during certain tests, particularly with higher heat fluxes and lower Reynolds number conditions that resulted in higher wall temperatures. The transient average Nusselt numbers (Nu_L) of the channel obtained from the experimental measurements are lower than those calculated from the Sieder–Tate correlation (Nu_O); however, the ratio (Nu_L/Nu_O) increases with the increase in Reynolds number. The ratio is around 0.25 at the lower end of Re and then increases to 0.7 at the maximum Re studied in the present investigation.     

Flow fluctuation measurement in the flow-through path of continuous electric-discharge CO<Subscript>2</Subscript>-laser contour

We have experimentally proved the applicability of hot-wire anemometer method to measure fluctuations at low pressures and gas flow rates when medium is no longer considered as continuous. Use of individual calibration at working conditions serves to apply standard technique for determination of sensitivity coefficients of hot-wire probes. Additional investigations are necessary to take into account influence of Knudsen number and, possibly, other parameters in heat transfer law presented as criterial dependence of Nusselt number on Reynolds number. Hot-wire measurement of mean velocity distribution and their fluctuations in the flow-through path of electric-discharge CO₂ laser have been performed. The level of velocity fluctuations in the vicinity of anode is high that is caused by the zone of interacting flows from the ventilators rotating in opposite directions forming in the symmetry plane. Placing of the damping screen between the ventilator and air gap allows decreasing fluctuations intensity to the acceptable level. It has been ascertained that the vortex shedding with high intensity of fluctuations which influence is noticeable in significant part of air gap is formed in the wake behind the streamlined cathode. However, pulsation level in the proper gap does not exceed permissible values.     

Forced and mixed convection heat transfer from an array of cylinders to a liquid submerged jet

The results of an experimental investigation concerning the heat transfer from three cylindrical heaters to a water jet are reported in the form of correlating equations, which express the Nusselt number versus the Reynolds, Prandtl and Grashof numbers and some dimensionless ratios characterising the configuration. As the experienced range of the thermal flux is wide (2·10⁴ ≤ q̇ ≤ 6·10⁵ W·m⁻²), the influence of the free convection, which was shown to be negligible in previous studies, is carefully investigated in the present one. This influence appears still negligible up to the maximum value of q̇ for the heater impinged by the jet; on the contrary it is remarkable for the heaters lying in its wake. Another aspect which is carefully studied is the influence both of the ratios characterising the configuration and of the impingement direction: accordingly the values of these ratios and the kind of impingement which yield the maximum Nusselt number are clearly singled out. The investigation is completed by some visualization experiments which allow us to qualitatively clarify some aspects of the interaction between the dynamic and thermal fields.     

The effects of porosity and permeability on fluid flow and heat transfer of multi walled carbon nano-tubes suspended in oil (MWCNT/Oil nano-fluid) in a microchannel filled with a porous medium

The forced convection heat transfer and laminar flow in a two-dimensional microchannel filled with a porous medium is numerically investigated. The nano-particles which have been used are multi walled carbon nano-tubes (MWCNT) suspended in oil as the based fluid. The assumption of no-slip condition between the base fluid and nano-particles as well as the thermal equilibrium between them allows us to study the nanofluid in a single phase. The nanofluid flow through the microchannel has been modeled using the Darcy–Forchheimer equation. It is also assumed that there is a thermal equilibrium between the solid phase and the nanofluid for energy transfer. The walls of the microchannel are under the influence of a fluctuating heat flux. Also, the slip velocity boundary condition has been assumed along the walls. The effects of Darcy number, porosity and slip coefficients and Reynolds number on the velocity and temperature profiles and Nusselt number will be studied in this research.     

Experimental Analysis of Gas Micro-Convection Through Commercial Microtubes

In this article, an experimental campaign devoted to analyzing the forced micro-convection features of heated gas flows through commercial stainless-steel microtubes having inner diameters of 172 μm and 750 μm is described. The experimental results obtained by heating the microtubes with an imposed uniform heat flux (H-boundary condition) at the external wall, in terms of Nusselt numbers, are compared to the predictions of the classical correlations validated for conventional pipes and to the correlations proposed for gas flows through microtubes under laminar and transitional conditions (100 < Re < 4,000). The cross-sections of the tested microtubes enabled the analysis of the effects of wall axial heat conduction on the Nusselt number. It was observed that the Nusselt number is strongly dependent on the Reynolds number in the laminar regime, and this fact is explained in the article with the effects of wall axial heat conduction and the difficulties in the experimental determination of the right exit bulk temperature of the gas flow, which cannot be ignored in the thermal analysis. The agreement between the Gnielinski correlation and the experimental Nusselt number is poor, especially for low Reynolds numbers, if one uses the average gas bulk temperature, obtained as the arithmetic mean between the inlet and outlet gas bulk temperature, in the definition of the experimental Nusselt number. On the contrary, the agreement with the Gnielinski correlation improves if the local wall-gas temperature difference near the exit of the microtube is used instead. The experimental results presented in the article demonstrate that the criteria for the design of accurate micro-convection tests can be quite different from those for the analysis of forced convection through conventional pipes.     

EXPERIMENTAL INVESTIGATION ON THE HEAT TRANSFER OF TURBULENT FLOW IN A PIPE OSCILLATING AT LOW FREQUENCIES

An experimental study was performed focusing on heat transfer and friction coefficient associated with turbulent oscillating tube flow. For this goal an oscillating mechanism was designed. Experiments were conducted for the low oscillating frequency in the range of 0.008–1.988 Hz and dimensionless amplitude was chosen as X₀ = 0.3, 0.6, and 0.9. Reynolds number was changed from 0.5 × 10⁴ to 2.5 × 10⁴. The bulk temperature of the fluid at the exit of the oscillating section was fond to be increasing with oscillating frequency and amplitude. For the oscillating cases, heat transfer enhancement is obtained 52% for f = 1.988 s^?1, 40% for f = 1.320 s^?1, and 28% for f = 0.008 s^?1, in comparison with the smooth pipe at the highest Reynolds number. The results also showed that Nusselt number and friction coefficient also increased with increasing frequency and amplitude.     

HEAT TRANSFER CHARACTERISTICS OF AN IMPINGING BUTANE/AIR FLAME JET OF LOW REYNOLDS NUMBER

An experimental study was performed to determine the heat transfer characteristics of a premixed butane/air round flame jet, of low Reynolds number, impinging upwards normally on a flat rectangular plate. The effects of the exit Reynolds number and equivalence ratio of the flame jet, and the distance between the nozzle and the impingement plate, on the thermal performance of the jet were examined. The range of Reynolds numbers was selected to cover the laminar to the transitional flow conditions. The investigations were conducted with equivalence ratios corresponding to the fuel-rich, stoichiometric, and fuel-lean conditions. The nozzle-plate distance was varied from 1d to 8d. Within the range of Reynolds numbers investigated, the highest Nusselt numbers were obtained at the equivalence ratio of φ = 0.85 when the nozzle-plate distance was maintained at 5d. At the stoichiometric condition, the highest Nusselt number was obtained at the nozzle- plate distance of 6d. Nondimensional correlations were obtained from the experimental results and presented to predict the maximum Nusselt number and average Nusselt number for laminar flame jets as a function of the nozzle-plate distance, Reynolds number, and equivalence ratio.     

Experimental and Numerical Study of Free Convection on an Isothermal Downward Cone

Abstract

The laminar free-convection heat transfer from an isothermal downward cone in air is investigated experimentally and numerically. The experimental investigation is carried out by Mach-Zehnder interferometery technique and the numerical simulation was done by Fluent. The cone tip angle has been kept constant to 45° and it was suspended from its base throughout the experiment. This article focuses on the effect of Rayleigh number variation on the local and average free-convection heat transfer coefficient over the conical surface. The local and average Nusselt numbers were determined for the Rayleigh number range of 4.9×10⁵ to 1.1×10⁶. Also, the experiment and the numerical simulation were carried out on a vertical isothermal cylinder of circular cross section in order to compare results with other researchers for the verification of our experimental and numerical results. The significant influence of the upper end surface of the cone, both in the experimental and numerical studies, indicated a recirculation region above the upper end surface which affects the local convection heat transfer at the slant trailing edge and causes it to increase. Also, a correlation for the calculation of the local Nusselt number over the cone is proposed.     

Numerical study of flow and heat transfer from a torus placed in a uniform flow

Forced convection heat transfer characteristics of a torus (maintained at a constant temperature) immersed in a streaming fluid normal to the plane of the torus are studied numerically. The governing equations, namely, continuity, momentum and thermal energy in toroidal coordinate system, are solved using a finite difference method over ranges of parameters (aspect ratio of torus, 1.4 ≤ Ar ≤ 20; Reynolds number, 20 ≤ Re ≤ 40; Prandtl number, 0.7 ≤ Pr ≤ 10). Over the ranges of parameters considered herein, the nature of flow is assumed to be steady. In particular, numerical results elucidating the influence of Reynolds number, Prandtl number and aspect ratio on the isotherm patterns, local and average Nusselt numbers for the constant temperature (on the surface of the torus) boundary condition. As expected, at large aspect ratio the flow pattern and heat transfer are similar to the case of flow and heat transfer over a single circular cylinder.     

Numerical simulation of heat transfer and fluid flow of Water-CuO Nanofluid in a sinusoidal channel with a porous medium

This study has compared the convection heat transfer of Water-based fluid flow with that of Water-Copper oxide (CuO) nanofluid in a sinusoidal channel with a porous medium. The heat flux in the lower and upper walls has been assumed constant, and the flow has been assumed to be two-dimensional, steady, laminar, and incompressible. The governing equations include equations of continuity, momentum, and energy. The assumption of thermal equilibrium has been considered between the porous medium and the fluid. The effects of the parameters, Reynolds number and Darcy number on the thermal performance of the channel, have been investigated. The results of this study show that the presence of a porous medium in a channel, as well as adding nanoparticles to the base fluid, increases the Nusselt number and the convection heat transfer coefficient. Also the results show that As the Reynolds number increases, the temperature gradient increases. In addition, changes in this parameter are greater in the throat of the flow than in convex regions due to changes in the channel geometry. In addition, porous regions reduce the temperature difference, which in turn increases the convective heat transfer coefficient.     

Lattice Boltzmann simulation of double diffusive natural convection in heterogeneously porous media of a fluid with temperature-dependent viscosity

Double diffusive natural convection inside a porous cavity with non-uniform porosity has been numerically studied. The cavity was filled with two parallel porous layers with different porosity. Considering the effects of temperature-dependent viscosity, simulations have been done via the Lattice Boltzmann method (LBM) at representative elementary volume (REV) scale. In this study, the effect of porosity, buoyancy ratio, the viscosity-variation number and thermal Rayleigh number on heat and mass transfer rates was investigated. The streamlines, isotherms, isoconcentrations, average Nusselt number and average Sherwood number curves of different parameters were discussed in detail. It was observed that the governing parameters has significant impact on the fluid flow, temperature and concentration distributions. In addition, the average Nusselt and Sherwood numbers are increase with an reduce in the viscosity-variation number. Further, as the absolute value of buoyancy ratio and thermal Rayleigh number increases, the effect of porosity and viscosity changes on the heat and mass transfer enhancement was augmented.     

A numerical study of laminar natural convective heat transfer inside a closed cavity with different aspect ratio

Two-dimensional steady-state laminar natural convection was studied numerically for differentially heated air-filled closed cavity with adiabatic top and bottom walls. The temperature of the left heated wall and cooled right wall was assumed to be constant. The governing equations were iteratively solved using the control volume approach. In this paper, the effects of the Rayleigh number and the aspect ratio were examined. Flow and thermal fields were exhibited by means of streamlines and isotherms, respectively.Variations of the maximum stream function and the average heat transfer coefficient were also shown. The average Nusselt number and was correlated to the Rayleigh number based on curve fitting for each aspect ratio. The investigation covered the range 10⁴ ≤ RA ≤ 10⁷ and is done at Prandtl number equal to 0.693. The result shows the average Nusselt number is the increasing function of Rayleigh number. As the aspect ratio increases, Nusselt number decreases along the hot wall of the cavity. As Rayleigh number increases, Nusselt number increases. Result indicates that at constant aspect ratio, with increase in Rayleigh number the heat transfer rate increases.