Nitro musks in cosmetic products—determination by headspace solid-phase microextraction and gas chromatography with atomic-emission detection

Summary The combination of headspace solid-phase microextraction with atomic-emission detection enables highly selective and sensitive determination of itro musk compounds in cosmetic products. Sample preparation is considerably simplified; there is no solvent extraction step. Enrichment is influenced by the type and amount of cosmetic product investigated. The lowest amount giving well detectable peaks is 1 mg musk compound per kg sample. Calibration curves obtained from spiked solutions of selected reference cosmetics in water show very good linearity. Relative standard deviations of peak areas from repeated measurements are usually <10%. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Retention and enantioselectivity properties of β-cyclodextrin polymers and derivatives on porous silica for reverse-phase liquid chromatographic separation of enantiomers

Summary Chiral stationary phases (CSP) based on porous silica coated with β-cyclodextrin polymer and methylated or acetylated derivatives have been prepared. Their enantiomer separation capability was tested and compared under reversed-phase mode elution conditions. Noticeable changes in retention properties werenoted and in many cases a reverse enantioselectivity was evidenced, as a consequence of a strong modification of the energy, geometry and number of points of contact between solutes and stationary phase sites of molecular recognition. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996.     

A new porous-layer activated-charcoal-coated fused silica fiber: Application for determination of BTEX compounds in water samples using headspace solid-phase microextraction and capillary gas chromatography

Summary Extra-fine powdered activated charcoal has been used as stationary phase (coating layer) in solid-phase microextraction (SPME). The efficiency and reliability of the prepared device have been investigated for the extraction of some volatile organic compounds such as benzene, toluene, ethylbenzene and xylene isomers (BTEX) from the headspace of water samples. Monitoring of the extracted compounds and further quantitative analysis of the real samples have been performed by capillary GC-FID. Effects of several factors such as temperature, addition of salt, and stirring speed on extraction efficiency and exposure time have been studied. Under optimum conditions, extraction recoveries for these compounds from 50 mL water were >95%. The calibration graphs were linear in the range 5 to 10⁴ pg mL⁻¹ and the detection limit for each BTEX compound was 1.5–2 pg mL⁻¹. The results obtained by use of this porous layer activated charcoal (PLAC)-coated fiber have also been compared with results reported in the literature by use of a polydimethylsiloxane (PDMS)-coated fiber. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Characteristics of immunosorbents used as a new approach to selective solid-phase extraction in environmental analysis

Summary The trace-level determination of organic pollutants in complex matrices is difficult and often not reliable because theccurrent extraction procedures are non-selective. New extraction sorbents involving antigen-antibody interactions, called immunosorbents (ISs), have been synthesised in order to trap a group of structurally related pollutants. The IS capacity is always high for the analyte-antigen used to make the antibodies, but can be low for some related compounds. In this work, we show the relationship that exists between capacity, break-through volume and recovery of analytes because of the competition between the structurally related compounds for antibody sites. Breakthrough due to the overloading of the column should be avoided because calibration curves are no longer linear. The capacity of two ISs, one made for trapping the triazine pesticide group and the second for the phenylurea, group, have been optimised by selecting silica with 50 nm pore size. Calibration curves are linear for all the compounds in a mixture of ten phenylureas up to a concentration of 5 to 10 μg L⁻¹ for each compound when handling 50 mL water samples through a precolumn packed with 0.22 g of IS. Under these conditions, reliable quantitative results are obtained because calibration curves are similar when compounds are alone or in a mixture. Application to the clean-up of soil extracts illustrates the high selectivity and the high potential of these new sorbents in environmental analysis. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Analysis of organic pollutants in water at trace levels using fully automated solid-phase extraction coupled to high-performance liquid chromatography

Summary A method has been developed for the determination of trace levels of 32 pesticides, 19 explosives and 16 polycyclic aromatic hydrocarbons (PAH) in water in three individual steps. Solid-phase enrichment (SPE) is coupled to high-performance liquid chromatography (HPLC) with a fully automated system. The organic pollutants are enriched on reusable cartridges packed with adsorbent materials: pesticides and explosives on a mixed bed of divinylbenzene-ethylvinylbenzene copolymers (LiChrolut EN^?) and perfluorinated polyethylene (PolyF^?), and polycyclic aromatic hydrocarbons on C₁₈-modified silica (Zorbax^? ODS1). Thermally assisted desorption (TAD) has been shown to increase the recovery of analytes significantly. As all enriched analytes are transferred to the detector, only fifty millilitres of sample is needed for each single on-line analysis, compared with at least a litre for conventional methods. The separation of the enriched organic analytes is performed on specialized HPLC columns based on reversed-phase materials. The limits of detection of the system employed were found to be below 100 ng L⁻¹. Use of fluorescence detection for the polycyclic aromatic hydrocarbons resulted in limits of detection in the upper pg L⁻¹ range. Thek values, number of theoretical plates, the recovery rates and the limits of detection of this method for fast screening of organic pollutants from three fifty-millilitre aqueous samples are described. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Matrix solid phase dispersion–Soxhlet simultaneous extraction clean-up for determination of organochlorine pesticide residues in tobacco

A novel method combining matrix solid phase dispersion (MSPD) with Soxhlet simultaneous extraction clean-up (SSEC) was developed. Being a single-step extraction and clean-up procedure, it could be used instead of multistep solvent extraction and Florisol column clean-up. It not only reduces sample contamination during the procedure, but it also decreases the amount of organic solvent needed. The retention times of standards were used to qualitatively assess the method, and the external standard method was used to quantitatively assess it. Residues of organochlorine pesticides (OCP) in tobaccos were determined by gas chromatography–electron capture detection (GC–ECD), and their identities were confirmed by the standard addition method (SAM). The performance of the method was evaluated and validated: the detection limit was 0.01–0.02 μg g⁻¹, relative standard deviations were 5–26%, and recoveries were 72–99% at fortification levels of 0.10, 1.00 and 10.0 μg g⁻¹. The analytical characteristics of MSPD–SSEC compared very favorably with the results from the classical multistep solvent extraction and Florisol column clean-up method.     

Fast supercritical fluid chromatography using capillaries packed with nonporous particles

Summary Packed columns containing microparticles provide high column efficiency per unit time and strong retention characteristics compared with open tubular columns, and they are favored for fast separations. Nonporous particles eliminate the contribution of solute mass transfer resistance in the intraparticle void volume characteristic of porous particles, and they should be more suitable for fast separations. In this paper, the evaluation of nonporous silica particles of sizes ranging from 5 to 25 μm in packed capillary columns for fast supercritical fluid chromatography (SFC) using neat CO₂ is reported. These particles were first deactivated using polymethyl-hydrosiloxanes and then encapsulated with a methylphenylpolysiloxane stationary phase. The retention factors, column efficiencies, column efficiencies per unit time, separation resolution, and separation resolution per unit time for fast SFC were determined for various length capillaries packed with various sizes of polymerencapsulated nonporous particles. It was found that 15 μm nonporous particles provided the highest column efficiency per unit time and resolution per unit time for fast packed capillary SFC. Under certain conditions, separations were completed in less than 1 min. Several thermally labile silylation reagent samples were separated in times less than 5 min. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Purity testing of sulfonic acids of different chain length by capillary electrophoresis

Summary A CZE method has been developed for the purity testing of sulfonic acids. By use of an optimized electrolyte system, short analysis times and high resolution (R _S=2–4) can be achieved for inorganic anions and for alkyl sulfonic acids from methane-1- to decane-1-sulfonic acid. By use of indirect UV detection by-products of different sulfonic acids can be determined at the 2 m level, equivalent to 0.02%,w/w. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Characterization and prediction of retention in gradient-elution normal phase HPLC with ternary gradients

Summary Chromatographic behaviour of phenylurea herbicides and phenols on a silica gel column with ternary gradient elution using mobile phases containing dry 2-propanol, n-heptane and dioxane was investigated. With dried solvents and the temperature controlled to ±0.1 °C, the data from repeated experiments measured on the same column after ten months of use were reproducible. Algorithms were suggested for characterization and prediction of retention in ternary gradients at a constant ratio of the two polar solvents (elution strength gradients) and at a constant sum of their concentrations (selectivity gradients). These were based on two- and three-parameter equations describing the dependence of the sample retention factors (isocratic) on the concentration of the polar solvent in binary mobile phases. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

A study of the behaviour of some new column materials in the chromatographic analysis ofCatharanthus alkaloids

Summary New column-packing materials specially designed for the HPLC analysis of basic compounds have been tested for the analysis ofCatharanthus alkaloids. Mobile phase optimization was performed for each column tested. The influence of mobile phase pH, nature and content of the organic modifier and salt concentration on retention, selectivity and resolution was studied. An important factor in the separation proved to be the pH of the eluent, because of the widely different pK _a values of the analytes. Complete separation was easily achieved on ODS columns, but polymeric materials also gave acceptable results. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Determination of pharmaceuticals,steroid hormones,and endocrine-disrupting personal care products in sewage sludge by ultra-high-performance liquid chromatography–tandem mass spectrometry

A sensitive method has been developed and validated for the determination of diverse groups of pharmaceuticals, steroid hormones, and hormone-like personal care products in sewage sludge. Samples were extracted by ultrasonic-assisted extraction followed by solid-phase extraction cleanup. For determination of estrogens and hormone-like phenolic compounds, sample extracts were further derivatized with dansyl chloride and purified with silica gel column chromatography to improve the analytical sensitivity. The chemicals were determined by ultra-high-performance liquid chromatography–tandem mass spectrometry (UHPLC-MS/MS) in multiple-reaction monitoring mode. Recoveries ranged mostly from 63% to 119% with relative standard deviations within 15%. Method quantification limits were 0.1–3 ng g⁻¹ dry weight (dw) for sewage sludge. The method was applied to a preliminary investigation of pharmaceuticals and personal care products (PPCPs) in sewage sludge and sediment in the Pearl River Delta, South China. Triclosan, triclocarban, 2-phenylphenol, bisphenol A, and parabens were ubiquitously detected at 3.6–5088.2 ng g⁻¹ dw in sludge and 0.29–113.1 ng g⁻¹ dw in sediment samples, respectively. Estrone, carbamazepine, metoprolol, and propranolol were also frequently quantified in the sludge and sediment samples. The dewatering process caused no significant losses of these PPCPs in sewage sludge.     

Contribution of the lipophilic buffer to chiral recognition under reversed-phase conditions

Summary A lipophilic buffered aqueous mobile phase, without organic modifier, was used for the high performance liquid chromatographic enantioseparation of D,L-lactic acid on a Merck ChiraSpher (250 mm×4 mm i.d.) column in which the chiral selector is poly(N-acryloyl-S-phenylalanine ethyl ester) bonded to a spherical silica particle. The lipophilicity of the buffer was achieved by addition of triethylammonium phosphate, the ‘ethyl’ apolar chains of which dynamically modified the ChiraSpher stationary phase and increased its hydrophobic character. The ion-paired (cethyltrimethylammonium bromide) analyte enantioseparation was realized by hydrogen-bonding and dipole-dipole complexation on the ChiraSpher stationary phase, superimposed on simultaneous reversed-phase partitioning. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Immunoaffinity-based extraction of phenylurea herbicides using mixed antibodies against isoproturon and chlortoluron

Summary The analysis of several phenylurea herbicides in different waters is described using an immunoaffinity column clean-up and determination by high performance liquid chromatography. The pesticides were selectively retained on a solid phase extraction column containing antibodies to chlortoluron and to isoproturon immobilised onto silica. Selected phenylureas were eluted using a simple phosphate buffered saline/ethanol mixture at low pH. The immunoaffinity approach gave extracts free of interfering substances and allowed detection limits comparable to those required for pesticides in water in the European Community. The proposed method was successfully applied to the determination of chlortoluron, isoproturon, linuron and chlorbromuron in tap and river water. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

High-performance liquid chromatographic determination of diltiazem in human plasma after solid-phase and liquid–liquid extraction

A selective, sensitive, and accurate high-performance liquid chromatographic method for determination of diltiazem in plasma samples has been developed and validated. The effects of mobile phase composition, buffer concentration, mobile phase pH, and concentration of organic modifiers on retention of diltiazem and internal standard were investigated. Solid-phase and liquid–liquid extraction were examined and proposed for isolation of the drug and elimination of endogenous plasma interferences. A 5 m Lichrocart Lichrospher 60 RP-select B chromatographic column was used; the mobile phase was acetonitrile–0.025 mol L^–1 KH₂PO₄ (pH 5.5), 35:65 ( v / v) at a flow-rate of 1.5 mL min^–1. The detection wavelength was 215 nm. The calibration plots were linear in the concentration range 20.0–500.0 ng mL^–1. The method has been implemented to monitor diltiazem levels in patient samples.     

Effective preparation of crack-free silica aerogels via ambient drying

Effective ambient-drying techniques for synthesizing crack-free silica aerogel bulks from the industrial waterglass have been developed. Silica wet gels were obtained from aqueous colloidal silica sols prepared by ion-exchange of waterglass solution (4–10 wt% SiO₂). Crack-free monolithic silica aerogel disks (diameter of 22 mm and thickness of 7 mm) were produced via solvent exchange/surface modification of the wet gels using isopropanol/trimethylchlorosilane/n-Hexane solution, followed by ambient drying. The effects of the silica content in sol and the molar ratio of trimethylchlorosilane/pore water on the morphology and property of final aerogel products were also investigated. The porosity, density, and specific surface area of silica aerogels were in the range of 92–94%, 0.13–0.16 g/cm³, and ∼675 m²/g, respectively. The degree of springback during the ambient drying processing of modified silica gels was 94%.     

Extension of the measuring range of balances

The basic principle of comparing the sample mass with the mass of a reference body in equilibrium gives the equal-armed beam balance a unique accuracy. Main parameters characterising the suitability of the instrument are measuring range, resolution and relative sensitivity (resolution/maximum load). The historical development of the values of these parameters achieved depended strongly on the practical need in those times. Technically unfavourable scales of the oldest Egyptian dynasties (~3000 BC) could resolve mass differences of 1 g and had a relative sensitivity of at least 10^–3. More sophisticated instruments from the 18^th Dynasty (~1567–1320 BC) achieved a relative sensitivity of 10^–4 independent of the size of the instrument. In 350 BC Aristotle clarified the theory of the lever and at about 250 BC Archimedes used the balance for density determinations of solids. The masterpiece of a hydrological balance was Al Chazini’s 'Balance of Wisdom’ built about 1120. Its relative sensitivity was 2⋅10^–5. Real progress took place when scientists like Lavoisier (1743–1794) founded modern chemistry. At the end of the 19^th century metrological balances reached a relative sensitivity of 10^–9 with a maximum load of several kilogrammes. That seems to be the high end of sensitivity of the classical mechanical beam balance with knife edges. Improvements took place by electrodynamic compensation (Emich, Gast). In 1909 Ehrenhaft and Millikan could weigh particles of 10^–15 g by means of electrostatic suspension. In 1957 Sauerbrey invented the oscillating quartz crystal balance. By observing the frequency shift of oscillating carbon nanotubes or of silica nanorods, masses or mass changes in the attogram or zeptogram have been observed recently.     

The spatial distribution of poly(methyloctylsiloxane) deposited by solvent evaporation in the pores of HPLC silica particles

Summary Poly(methyloctylsiloxane) (PMOS), sorbed into the pores of HPLC silica particles by solvent evaporation, can function as a useful stationary phase for reversed-phase chromatography. The present work addresses the question of how the PMOS is distributed in the pores. Measurements of the surface area (BET, N₂) of a series of partially loaded samples (0–40% PMOS, m/m) using a typical batch of HPLC silica (10 μm irregular particles with 6 nm pores) show that the specific surface area of the samples decreases linearly with the specific loading (mass of PMOS per gram of silica). This result is not consistent with a “film” model in which the PMOS is deposited uniformly on the pore walls, but is consistent with a model in which long segmented “plugs” of PMOS are deposited within the pore system. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Quantitative determination of lansoprazole in human serum by HPLC

Summary Lansoprazole is a new inhibitor of gastric proton secretion. An HPLC method for the quantitative determination of lansoprazole in serum is described. The method consists of liquid-liquid extraction and enrichment of the analyte and subsequent reverse-phase liquid chromatography with UV detection. The method is specific, sensitive and practical. It has been applied to serum from healthy volunteers. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Determination of adapalene (CD271/differin®) and retinol in plasma and tissue by on-line solid-phase extraction and HPLC analysis

Summary Adapalene, the active constituent of Differin^?, is a novel potent retinoid (vitamin A analogue) for the topical treatment of acne vulgaris. The clinical usefulness of retinoids is limited by a number of side effects, such as teratogenicity and skin irritation. A method has been developed for simultaneous determination of adapalene and retinol in plasma and tissue in in vivo and in vitro studies for the determination of the pharmacokinetic profile and the influence of adapalene on the endogenous retinol level. The new method was developed by coupling an autosampler to an automated solid-phase extraction unit on-line with a gradient HPLC system using UV and fluorescence detection. The low detection limit (0.25 ng mL⁻¹ for adapalene), the small sample weight (50 mg) and the high degree of automation make this method convenient for analysis of biological samples in animal and human studies. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996.     

Preparation and evaluation of a functionalized polymer-coated silica based sorbent for metal ion separation

A silica based sorbent with an anion complexone polymer coating, [24]ane-N₆ macrocycle, was prepared. The chelation properties of this material were investigated by elemental analysis, infrared spectra and Voige’s method. The polymer-coated silica column (25– 40 μm, 100 × 4.6 mm i.d.) was employed for trace metal analyses. Oxalic acid, malonic acid, succinic acid, citric acid, phthalic acid and acetic acid were used as mobile phases. Their retention characteristics were elucidated. Oxalic acid was found to be the most effective eluent. With a mobile phase consisting of oxalic acid (25 mM) and sodium nitrate (25 mM) at pH 4.2, the separation of copper(II), cadmium(II), cobalt(II) and zinc(II) in sea water could be achieved. The identification of metal ions was performed at 510 nm using 4(2-pyridylazo)resorcinol (1 × 10^–4 M) as post column reagent. The limits of detection were 5 × 10^–7 M, 1 × 10^–5 M, 3 × 10^–5 M and 2 × 10^–6 M for copper(II), cadmium(II), cobalt(II) and zinc(II) based on three times the standard deviation of the response for the lowest concentration (n = 5) in the chromatogram with a sample volume of 50 μL. For evaluation of data reliability, oyster tissue (NIST SRM 1566 a) was studied with the proposed system. Received: 9 February 1998 / Revised: 15 May 1998 / Accepted: 16 June 1998