Adsorption of Bovine Serum Albumin onto Polystyrene Latex Particles Bearing Saccharidic Moieties

The adsorption of bovine serum albumin (BSA) onto polystyrene latexes bearing various amounts of sugar moieties has been investigated as a function of pH and ionic strength and the results were compared to those for bare polystyrene latexes having negative surface charges. The functionalized latexes were produced by seeded copolymerization of (0.3 μm) liposaccharidic monomer onto polystyrene particles obtained by soap-free emulsion polymerization of styrene using potassium persulfate as initiator. At first, the electrophoretic mobility behavior of the various latexes was examined as a function of pH: a significant decrease was observed in the case of saccharide-containing latex particles compared to the bare particles. The adsorption of BSA onto these latexes exhibited a reduced amount of adsorbed BSA for those latex particles bearing saccharide groups. This adsorbed amount depends on the yield of saccharidic monomer incorporated onto the surfaces of the latex particles.     

Hydrophilic magnetic polymer latexes. 1. Adsorption of magnetic iron oxide nanoparticles onto various cationic latexes

With a view to preparing monosized hydrophilic functional magnetic latex particles based on a two-step strategy using anionic iron oxide and cationic polymer latexes, the adsorption step was systematically investigated for a better control of the subsequent encapsulation step. The iron oxide nanoparticles were first obtained according to the classical precipitation method of ferric and ferrous chloride salt using a concentrated sodium hydroxide solution, whereas the polystyrene (PS), P(S/N-isopropylacrylamide (NIPAM)) core–shell and PNIPAM latexes were produced via emulsion and precipitation polymerizations, respectively. The polymer and inorganic colloids were then characterised. The adsorption of iron oxide nanoparticles onto the three types of polymer latexes via electrostatic interaction was studied as a function of iron oxide particle concentration, charge density and the cross-linking density of the hydrophilic layer. The maximum amounts of magnetic nanoparticles adsorbed onto the various latexes were found to increase in the following order: PS < P(S/NIPAM) < P(NIPAM). This significant difference is discussed by taking into account the charge distribution in the hydrogel layer and diffusion phenomena inside the cross-linked hydrophilic shell. Received: 28 December 1998 Accepted in revised form: 15 April 1999     

Polystyrene and polystyrene-butadiene latexes stabilized by poly(N-isopropylacrylamide)

Latexes stabilized by poly(N-isopropylacrylamide) (polyNIPAM) were prepared by polymerizing NIPAM in the presence of polystyrene and polystyrene-butadiene latex or by styrene emulsion polymerization in the presence of NIPAM. In 0.01 M CaCl₂ polyNIPAM stabilized latexes exhibited critical flocculation temperatures in the range 32–35°C, which is approximately equal to the lower critical solution temperature of polyNIPAM in water. Partial substitution of NIPAM with some acrylamide (AM) gave higher flocculation temperatures. Coagulation studies with cleaned latex indicated that the polyNIPAM or polyNIPAM-co-AM polymer chains were anchored to the latex particle surfaces.     

Polystyrene latex particles coated with crosslinked poly(N-isopropylacrylamide)

Thermoresponsive colloidal particles were prepared by seeded precipitation polymerization of N-isopropylacrylamide (NIPAM) in the presence of a crosslinking monomer, N,N-methylenebisacrylamide (MBA), using polystyrene latex particles (ca. 50 nm in diameter) as seeds in aqueous dispersion. Phase transitions of the prepared poly(N-isopropylacrylamide), PNIPAM, shells on polystyrene cores were studied in comparison to colloidal PNIPAM microgel particles, in H₂O and/or in D₂O by dynamic light scattering, microcalorimetry and by ¹H NMR spectroscopy including the measurements of spin–lattice (T1) and spin–spin (T2) relaxation times for the protons of PNIPAM. As expected, the seed particles grew in hydrodynamic size during the crosslinking polymerization of NIPAM, and a larger NIPAM to seed mass ratio in the polymerization batch led to a larger increase of particle size indicating a product coated with a thicker PNIPAM shell. Broader microcalorimetric endotherms of dehydration were observed for crosslinked PNIPAM on the solid cores compared to the PNIPAM microgels and also an increase of the transition temperature was observed. The calorimetric results were complemented by the NMR spectroscopy data of the ¹H-signal intensities upon heating in D₂O, showing that the phase transition of crosslinked PNIPAM on polystyrene core shifts towards higher temperatures when compared to the microgels, and also that the temperature range of the transition is broader.     

Polystyrene(1)/poly(butyl acrylate-methacrylic acid)(2) core-shell emulsion polymers. Part I. Synthesis and colloidal characterization

Polystyrene (PS) (1)/Poly(n-butyl acrylate (BA)-methacrylic acid (MAA)) (2) structured particle latexes were prepared by emulsion polymerization using monodisperse polystyrene latex seed (118 nm) and different BA/MAA ratios. Three main aspects have been investigated: i) the polymerization kinetics; ii) the particle morphology as a function of reaction time; iii) the distribution of MAA units between the water phase and the polymer particles.The amount of MAA in the shell copolymer was found to be the main factor controlling the particle shape and morphology. The shape of the structured particles was, generally, non-spherical, and the shape irregularities increased as a particles was, generally, non-spherical, and the shape irregularities increased as a function of reaction time. At the beginning of the second stage reaction, new small particles were observed, which coalesced onto the PS seed as the polymerization proceeded. The distribution of the MAA groups in the latex particles and the serum was analyzed by alkali/back-acid titration, using ionic exchanged latexes. No MAA groups were detected in the latex serum. Due to the lowTg of the BA-MAA copolymers, alkali conductimetric titrations accounted for all the MAA groups on and within the polymer particles. Therefore, for these systems, this method is not only limited to a thin surface layer, as it is often assumed.     

Kinetic and particle size studies of emulsion polymerization of methyl methacrylate and styrene with using polyamidoamine dendrimer as seed

The emulsion polymerization of methyl methacrylate (MMA) and styrene (St) were investigated with using polyamidoamine (PAMAM) dendrimer as seed, potassium persulfate as initiator and sodium dodecyl sulfate as emulsifier. The effects of 4.0GPAMAM dendrimer concentration, initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature on the monomer conversion and polymerization rate were investigated. At the same time, the influence of the generation of PAMAM dendrimer on latex particle size was studied also. The results showed that the monomer conversion and polymerization rate increased with increasing initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature. But polymerization rate increased firstly with an increase in the 4.0GPAMAM dendrimer from 0.03 g to 0.09 g and then decreased with further increase to 0.12 g. When the concentration of 4.0GPAMAM dendrimer less than 1.449 × 10^?4 mol/L, the kinetic equation can be expressed by Rp∝[4.0GPAMAM]^0.772[SDS]^0.562[KPS]^0.589[M]^0.697, and the activation energy (Ea) of emulsion polymerization is 62.56kJ/mol. In additional, the copolymer latex particle size decreased and possessed monodispersity with increasing the generation of PAMAM dendrimer. According to FT-IR spectrum analysis, PAMAM dendrimer is successfully incorporated into the poly(PAMAM-St–MMA) latex particles.     

Preparation of polyacrylate–polysiloxane core–shell latex particles

Crosslinked polymer seed latexes of butyl acrylate, methyl methacrylate and methacrylic acid were synthesized with ethylene glycol dimethacrylate as a crosslinking agent in a first step. Three different processes of seeded emulsion polymerization were used to prepare an outlayer of polysiloxane on the above seed latex particles: (A) direct anionic polymerization of D₄ (octamethyl tetracyclosiloxane) catalyzed by potassium hydroxide; (B) direct cationic polymerization of D₄ onto the seed catalyzed by dodecylbenzene sulfonic acid; (C) a vinyl-containing polysiloxane prepared by copolymerization of D₄ and vinyl septamethyl tetracyclosiloxane was added before the D₄ cationic polymerization. Characterization by transmission electron microscopy showed that only process C provided satisfactory results. Film hardness was measured, and the latex film from process C demonstrated the lowest hardness of all the films. The mechanism of polymerization is discussed.     

Surface functionalization of styrene/butyl acrylate latex with a water‐soluble monosaccharide monomer. Synthesis and morphology of the polymer particles

New polymer latexes bearing saccharide moieties on the particle surface were synthesized by using a water‐soluble sugar monomer, such as 1‐deoxy‐1‐methacryl‐amido‐D ‐glucitol, (MAG). All the latexes were prepared by a two‐stage emulsion polymerization technique. In the first step, the core was prepared with butyl acrylate (BA) and styrene (St). In the second step, the seed latex was polymerized with ethyl acrylate (EA) and MAG. The influence of a bifunctional monomer such as allyl methacrylate (ALMA), introduced at various concentrations, on the final latexes morphologies and properties was investigated. It was found that the latex particles exhibit a core‐shell structure. The mass balance of MAG showed that the main part of the sugar moiety is on the shell layer. The molecular properties, such as structure, composition, and molecular weight, were determined by elemental analysis, ¹H‐ and ¹³C‐NMR spectroscopy. Colloidal (particle size and their distributions), thermal, and rheological properties were also studied. Copyright © 2003 John Wiley & Sons, Ltd.     

Carboxylic‐group distribution of carboxylated acrylate copolymer latexes with their properties in the presence of acrylic acid and monobutyl itaconate

A series of carboxylated acrylate copolymer latexes were prepared via two different emulsion polymerization technologies with different carboxylic‐group distribution and morphologies. The effects of the emulsifier, the initiator, and the carboxylic monomers [acrylic acid (AA) or monobutyl itaconate (MBI)] on the total conversion of the monomers and the properties of acrylate latexes and films have been investigated. The distribution of carboxylic groups (?COOH) measured by conductometric titration shows that the concentration of surface –COOH (C_s) and embedded –COOH (C_b) both increase with the increase of the amount of carboxylic monomers. For the latexes containing AA, –COOH tends to distribute on the surface of latex particles and in the aqueous phase, whereas –COOH tends to concentrate inside the core of latex particles for the latexes containing MBI. Transmission electron microscopy demonstrates that the latex particles are regular with narrow size distribution and have significant differences in morphologies when different carboxylic monomers and polymerization technologies were used. The stability of latex is satisfactory through the results of common stability and zeta potential tests. Moreover, the water absorption and contact angle experiment tests also revealed that the water resistance of the latex films is good. Copyright © 2011 John Wiley & Sons, Ltd.     

"CAGE" VANADYL POLYCARBOXYLATE-THIOUREA COMPLEX FOR THE POLYMERIZATION OF ACRYLONITRILE

The polymerization of acrylonitrile (AN) in aqueous nitric acid initiated by " cage " vanadyl polycarboxylate (P=VO)-thiourea (TU) complex was investigated. The overall rate ofpolymerization isThe relationship between the induction period (τ) and the temperature of polymerization as well as the concentrations of reactants can be expressed as follows :The molecular weight of polyacrylonitrile increases with increasing monomer concentration and decreases with increasing temperature of polymerization and concentrations of vanadyl polycarboxylate and thioureaThe polymerization mechanism was proposed and discussed.     

Preparation and characterization of cationic poly(n-isopropylacrylamide) copolymer latexes

Cationic poly(N-isopropylacrylamide) (NIPAM) copolymer latexes have been prepared at 70°C using methylene-bisacrylamide (MBA) as the crosslinking agent,2-2′-azobis-(2-amidinopropane hydrochloride) (V50) as the initiator and in the presence of 2-aminoethyl-methacrylate hydrochloride (AEM). It was found that the concentration of AEM plays a major role in the polymerization kinetics and particle nucleation. However, too high a concentration (2–5 mol%/NIPAM) caused the latex to be polydispersed together with the production of large amounts of polyelectrolytes. The presence of surface amino groups on the final particles under the protected form was revealed both by an ultraviolet spectrometry and nuclear magnetic resonance methods. It was indirectly evidenced through the electrophoretic mobility behavior of the latex particles (below and above the lower critical solubility temperature of the poly(NIPAM)) as well as by their stability against a monovalent electrolyte.     

Synthesis and properties of soap-free poly(methyl methacrylate-ethyl acrylate-methacrylic acid) latex particles prepared by seeded emulsion polymerization

In order to obtain functional polymer latex particles with clean surface and with surface carboxyl groups, P(MMA-EA) seed particles with the diameter of 335 nm were first synthesized via soap-free batch emulsion polymerization of methyl methacrylate (MMA) and ethyl acrylate (EA), and then the seeded emulsion copolymerization of MMA, EA and MAA (methacrylic acid) onto the seed particles were performed in the absence of emulsifier. Influences of ingredients and conditions on polymerization, latex particle size (D_p) and its distribution were investigated. Results showed that most of the monomers polymerized onto the seed latex particles in the second step of polymerization by using drop-wise addition method, and D_p increased from 483 nm to 829 nm with the mass ratio of core/shell monomers [C]/[S] decreased from 1:2 to 1:15. It was found that D_p decreased with the increase of MAA and initiator amounts, and the size of the latex particles became uniform with the decrease of MAA amount and with the increase of [C]/[S] value.     

Effect of Monomer Feeding Mode on thePreparation of Hollow Latexes with High MAA Content in the Core Latex Preparation简

In order to prepare hollow latex particles with optimum morphology based on osmotic swelling principle, three- layer core/shell latex particles with 40 wt% MAA in the core were first prepared via multistep seeded emulsion copolymerization, in which monomers were added by a semi-continuous process with monomer addition under two different forms： pure monomers＇ mixture （monomer addition）, and pre-emulsified monomers （pre-emulsion addition）. Then, the hollow latex particles with different morphologies were obtained after alkali post-treatment. Influences of the monomer feeding mode on the emulsion polymerization and the particle morphology were investigated. Results showed that the pre- emulsion addition could significantly improve the polymerization stability in each step, and greatly enhance the uniformity of shell encapsulation. The sizes of the core and core/shell latex particles obtained by the pre-emulsion addition were smaller and more uniform than those synthesized by the monomer addition, and the hollow latex particles with intact morphology were generated by alkali post-treating of the core/shell latexes prepared from the pre-emulsion addition. As the core size increased, the morphology of the post-treated particles underwent evolution from hollow to collapse. Moreover, the mechanism of the particle morphological evolution was proposed.     

Film‐formation property of vinylidene chloride‐methyl methacrylate copolymer latex. I. Effect of emulsion‐polymerization process

Changes in minimum film‐formation temperature (MFFT) during storage of latexes prepared from 91:9 wt % vinylidene chloride (VDC)‐methyl methacrylate (MMA) monomer mixture by seeded batch and seeded semicontinuous emulsion polymerization were investigated, with attention centered on polymer‐crystallization behavior during storage in the dispersed state. MFFT of latex prepared by the seeded batch process rose to 47 °C, whereas that of latex prepared by seeded semicontinuous process remained below 14 °C with storage at 20 °C for 12 weeks. Infrared absorption of latexes in the dispersed state and wide‐angle X‐ray diffraction of powder polymers obtained by lyophilization of fresh and stored latexes both indicated a much greater increase in polymer crystallinity during storage with latex prepared by the seeded batch process than with that prepared by the seeded semicontinuous process. Analysis of the copolymer composition drift calculated from reactivity ratios and ¹H NMR analysis indicated a wider sequence distribution and longer VDC sequences in polymer prepared by the seeded batch process than in polymer prepared by the seeded semicontinuous process. This explained the higher rate of crystallization during storage with latex prepared by the seeded batch process than with that prepared by the seeded semicontinuous process. Rising crystallinity during storage in the dispersed state is believed to have caused the MFFT rise. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 939–947, 2002     

含胺基功能性单体的聚合研究——ⅫⅠ.丙烯腈在N-丙烯酰-N′-苯基哌嗪及其聚合物作为增感剂下的光聚合

The photopolymerization of AN by using N-acryloyl-N'-phenylpiperazine (APP) and N-methacryloyl-N'-phenylpiperazine (MPP) as sensitizers under UV irradiation has been investigated. The corresponding polymerization kinetic equations are as follows:Rp [APP]^0.81[AN]^0.61 R_p [MPP]^0.48[AN]^0.77 R_p [P(APP)]^0.53[AN]^0.78 From the fluorescent analysis, it was confirmed that APP, MPP and P(APP) not only initiated the polymerization of AN but also entered into the chains of AN polymer. The photopolymerization mechanism for exciplex formation of AN with above sensitizers was proposed.     

STUDY ON THE POLYMERIZATION OF ACRYLONITRILE INITIATED BY POLYPROPYLENE-BASED VANADYL POLYIMIDODIACETATE——THIOUREA REDOX SYSTEM

The present paper deals with the kinetics of polymerization of acrylonitrile (AN) initialed by the redox system of polypropylene-based vanadyi polyimidodiacetate (PV)-thiourea (TU)in aqueous sulfuric acid in the temperature range from 25 to 40℃. The polymerization rate was measured by varying the concentrations of monomer, vanadyl polyimidodiacetate, thiourea and sulfuric acid. The overall rate of polymerization was summarized asRp=2.2×10~5e~(-6.560/RT) [AN]~(1.0)[PV]~(0.50)[TU]~(1.5)[H_2SO_4]~(2.0)The molecular weight of polyacrylonitrile based on the experimental data was:(?)=k 1/T [pv]~(0.50)[TU]~(1.5)[H_2SO_4]~(2.0)These results indicated that the chain radicals are terminated by combination and/or disproportionation rather than chain transfer. The cooperation effect of carboxylic groups and the macromolecular field effect of polymer supporter are the characters of vanadyl polyimidodiacetate such as the case reported in early paper.     

Polymer mediated peptide immobilization onto amino-containing N-isopropylacrylamide-styrene core-shell particles

Monodisperse cationic core-shell latex particles have been prepared using a shot polymerization process, with N-(3-aminopropyl)-methacrylamide-hydrochloride (APMH) as the functional monomer. The final latexes were characterized with respect to final polymerization conversion, water soluble polymer formation, particle size and size distribution, surface charge density and electrokinetic properties. Then the covalent grafting of maleic anhydride-alt-methyl vinyl ether (MAMVE) copolymer onto aminated latex particles was investigated. The most efficient conditions to obtain derivatised particles with no alteration of the colloidal stability were to control both polymer amount/latex particles concentration ratio and the mixing method of the two species. The charge inversion of the hydrolysed MAMVE functionalized particles was demonstrated by measuring the electrophoretic mobility as a function of pH. Finally, the covalent binding approach was implemented with peptide-MAMVE conjugates, confirming the great potential of this promising methodology for the preparation of reactive latex particles bearing peptides.     

反应性复合乳液的合成、表征及其交联反应

利用种子半连续乳液聚合方法合成了核层或壳层带有环氧基以及壳层带有羧基的3种不同核/壳结构的乳胶粒子,通过物理共混带环氧基和羧基的乳胶粒子,得到了两种反应性复合乳液.利用透射电镜和激光动态光散射对乳胶粒子进行了表征,其粒径分布较窄,粒径分布的多分散系数为0.062,平均粒径约76 nm,乳胶粒子具有明显的核/壳结构.通过胶膜的凝胶率和膨胀率的测定和红外光谱分析对反应性复合乳液中乳胶粒子的扩散及交联反应进行了研究,并探讨了不同核壳结构复合乳液对涂膜机械性能的影响.研究表明,当反应性复合乳液中的环氧基和羧基分别分布在乳胶粒子的核层和壳层时,有利于聚合物分子链的充分扩散和化学交联反应的进行,从而提高涂膜的物理化学性能,当甲基丙烯酸缩水甘油酯(GMA)含量为10 wt%时,涂膜的拉伸强度达20.3 MPa.     

Emulsifier-free emulsion copolymerization of styrene and butyl acrylate. II. Kinetic studies in the presence of ionogenic comonomers

Batch emulsifier-free copolymerizations of styrene (S) and butyl acrylate (BuA) have been performed for a S/BuA weight ratio = 50/50 in the presence of two types of functional comonomers [methacrylic acid (MAA) at different pHs] or potassium sulfopropylmethacrylate (SPM) and two initiators [potassium persulfate or 4–4′azobiscyanopentanoic acid (AZO)]. The use of AZO/MAA system results in the formation of polymer particles with only surface carboxylic end groups. The particle size of the final latexes can be adjusted with the MAA concentration, provided the polymerization is carried out at pH > 6.5. However, the higher the MAA concentration, the sooner the polymerization levels off in conversion. With the K₂S₂O₈/SPM system, particles bearing only sulfate and sulfonate groups are produced and the polymerization is complete. In that case, the particle size of the final latexes is smaller than with the previous system and 30% of the SPM is fixed on the particle surface, instead of 10% with MAA. Using SPM, a too high functional monomer concentration results in the latex destabilization caused by the formation of a large amount of polyelectrolytes. Kinetic studies indicate that most of the functional monomer is incorporated onto the particle surface during the last 30% conversion of the polymerization. A tentative explanation of such a behavior is discussed, based on the existence of two polymerization loci in the latex system.     

Grafting characterization of natural rubber latex particles: wet-STEM imaging contributions

Natural rubber latexes investigated in this study have been chemically modified by seeded emulsion polymerization. Depending on the water affinity of the monomer involved (MMA or DMAEMA), the expected result was the grafting of the corresponding polymer inside or on the surface of the latex particles. The present article focuses on the grafting characterization of these modified natural rubber latexes. In this purpose, non-imaging classical experimental methods such as dynamic light scattering and nuclear magnetic resonance have been completed by microscopy techniques, including transmission imaging in scanning electron microscopy (SEM) and a recent imaging mode called wet-STEM. It consists in transmission imaging in an Environmental SEM operating in the wet-mode, allowing transmission observations of particles suspended in a liquid layer with good resolution and contrast. In the present study, we have adopted a comparative characterization approach between a nongrafted natural rubber latex and two grafted ones. Such an approach indeed contributes to highlight the particles morphology resulting from chemical modification using either MMA or DMAEMA. Transmission images in SEM of thin foils are relatively well interpreted and are completed with wet-STEM images of latexes in their native state, bringing important contributions for grafting characterization.