Extraction and characterization of new natural lignocellulosic fiber Cyperus pangorei

This research is focused on the study of the physical, chemical, mechanical, and thermal properties of a newly identified natural stem fiber, Cyperus pangorei. The chemical composition of Cyperus pangorei fibers (CPF) such as cellulose, lignin, ash, moisture, and wax contents was evaluated. Besides these, the fiber density was determined and the apparent diameter was measured using an optical microscope. Further, tensile, thermal, XRD, and FT-IR studies were performed to evaluate the suitability of the fiber as a reinforcement. The surface topography of CPF was analyzed using scanning electron microscopy (SEM). Encouraging properties such as increased stiffness, fiber texture, and higher thermal stability suggest the suitability of CPF as reinforcement in polymer matrices.     

Extraction and characterization of lignocellulosic fibers from Luffa cylindrica fruit

The need for recyclable, renewable materials has resulted in an increased use of natural fibers for reinforcing polymers to suit a wide variety of applications. This study is mainly focused on the extraction and characterization of the lignocellulosic fibers derived from the ripened, dried Luffa cylindrica L. fruit. Characterization studies such as Fourier transform infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis are conducted and reported. Composite samples prepared using unsaturated polyester resin show an increasing impact strength on fiber loading. Fractured surface of the composites are examined using scanning electron microscope. Results show the feasibility of fibers for reinforcement in polymers.     

Extraction and characterization of natural cellulosic fiber from Passiflora foetida stem

This article presents a comprehensive characterization study of natural cellulosic fiber extracted from Passiflora foetida vine stem. The chemical composition of the obtained P. foetida fibers (PFFs) comprised high cellulose (77.9 wt%) and low lignin (10.47 wt%) content and had distinctly higher crystallinity (67.36%) of cellulose, which was determined by an X-ray diffractometer. The PFFs exhibited good tensile strength of 248?942 MPa associated with elongation (1.38?4.67%) during tensile testing. Thermogravimetric analysis revealed that the PFFs are thermally stable up to 320°C with kinetic activation energy of 85.46 kJ mol^?1; hence they ensure their suitability as a reinforcing phase in composites for potential applications.     

Extraction and characterization of cellulose nanocrystals from post-consumer wood fiberboard waste

This study investigates the potential of wood wastes, specifically post-consumer fiberboards, as a new source for cellulose nanocrystals (CNC). This underused resource has currently no commercially viable way to recycle it and so the volumes of fiberboard waste are growing rapidly. A sequential chemical fractionation was used to separate the three main constituents of wood, namely cellulose, hemicelluloses and lignin, and the non-wood components present in fiberboards, such as resins and finishes (e.g. varnishes, paints, plastics, laminates, etc.). Most of the non-cellulosic components and non-wood elements were removed by an alkali treatment followed by bleaching, resulting in a cellulosic fraction which is suitable for the further isolation of CNC by an acid hydrolysis step. The intermediate and final products were characterized by chemical composition, microscopic, spectroscopic and X-ray diffraction methods. The CNC obtained from wood waste are totally devoid of traces of contaminants and possess comparable characteristics and quality to those extracted from virgin wood fibers. The results indicate that fiberboard wastes can be used as promising alternative source for nanocelluloses production.     

Extraction and characterization of chitin from the beetle Holotrichia parallela Motschulsky

Insect chitin was isolated from adult Holotrichia parallela by treatment with 1 M HCl and 1 M NaOH, following by 1% potassium permanganate solution for decolorization. The yield of chitin from this species is 15%. This insect chitin was compared with the commercial a-chitin from shrimp, by infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and elemental analysis. Both chitins exhibited similar chemical structures and physicochemical properties. Adult H. parallela is thus a promising alternative source of chitin.     

Extraction and characterization of alkali-treated red coconut empty fruit bunch fiber

This article discusses the extraction and characterization of new natural fiber extracted from red coconut empty fruit bunch. The physicochemical, mechanical, and thermal properties of alkali-treated red coconut empty fruit bunch fibers (ARCEFBFs) were reported and compared with other natural fibers for the first time. Cellulose content (65.02 wt%), wax (0.32 wt%), density (1.421 g/cc), and tensile strength (1299.49 MPa) were identified in ARCEFBFs. Fourier transform infrared spectroscopy and X-ray diffraction analysis confirmed that ARCEFBFs are rich in cellulose content with crystallinity index of 53.6%. Thermogravimetric analysis revealed that these fibers are thermally stable until 270.48°C.     

Extraction and characterization of native heteroxylans from delignified corn stover and aspen

Dimethylsulfoxide-solubilized polysaccharides from delignified corn stover and aspen were characterized. The biomass was delignified by two different techniques; a standard acid chlorite and a pulp and paper QPD technique comprising chelation (Q), peroxide (P), and acid-chlorite (D). Major polysaccharides in all fractions were diversely substituted xylan. Xylan acetylation was intact after chlorite delignification and, as expected, xylan from QPD-delignified fraction was de-acetylated by the alkaline peroxide step. The study of DMSO-extractable xylans from chlorite-delignified biomass revealed major differences in native acetylation patterns between corn stover and aspen xylan. Xylan from cell walls of corn stover contains 2-O- and 3-O-mono-acetylated xylan and [MeGlcA-α-(1 → 2)][3-OAc]-xylp units. In addition, aspen xylan also contains 2,3-di-O-acetylated xylose. 1,4-β-d-xylp residues substituted with MeGlcA at O-2 position are absent in chlorite-delignified aspen xylan. Sugar composition in accord with NMR-spectroscopic data indicated that corn stover xylan is arabinosylated while aspen xylan is not. We have shown that corn stover xylan has similar structure with xylans from other plants of Poales order. No evidence was found to indicate the presence of 1,4-β-d-[MeGlcA-α-(1 → 2)][Ara-α-(1 → 3)]-xylp in corn stover xylan fractions.     

Extraction,modification, and characterization of natural ligno-cellulosic fiber strands from napier grass

Napier grass is a high-productivity perennial grass that is a very important forage for animals in the tropics. In this research work, fiber strands from Napier grass were extracted and the effect of acetic acid treatment on their chemical composition, morphological and structural changes, and tensile and thermal properties was studied. The acid treatment was carried out using glacial acetic acid solution at three different concentrations (5, 10, and 15%) for 2 h. Chemical analysis indicated lowering of amorphous hemicellulose content on acid treatment. FT-IR spectroscopic studies revealed variation of functional groups on acid treatment. Scanning electron micrographs indicated roughening of the surface of the fiber strands due to the removal of the hemicellulose layer on acid treatment. X-ray diffraction analysis indicated an increase in crystallinity of the fiber strands on acid treatment. The thermal stability and tensile properties of the fiber strands increased on acid treatment. This fiber has competitive advantages when evaluated with other natural fibers and can be developed further as a potential reinforcement in polymer matrix composites.     

Extraction and characterization of new cellulosic fibers from Indian mallow stem: An exploratory investigation

Natural fibers are one of the good alternative sources for replacing synthetic fiber and reinforcing polymer matrices because of their eco-friendly nature. This investigation deals with the extraction and characterization of new natural fiber from Indian mallow plant stem. The physico-chemical, thermal, and mechanical properties of Indian mallow fibers (IMFs) were reported and compared with other natural fibers for the first time. Cellulose (78.22%), wax (0.47%), density (1.33 g/cm³), and tensile strength (979.83 MPa) were recognized in IMFs. Fourier transform-infrared spectroscopy, X-ray diffraction, and thermo-gravimetric analysis confirmed that IMFs are rich in cellulose content and thermally stable with a crystallinity index of 72%.     

Extraction and characterization of the saponifiable lipid fraction from microalgae Chlamydomonas sp. cultivated under stress

Journal of Thermal Analysis and Calorimetry - Microalgae when subjected to nutrient restriction conditions, inducing environmental stress, are prone to total lipid accumulation and changes in the...     

Extraction and characterization of total phenolic and flavonoid contents from bark of Swietenia macrophylla and their antimicrobial and antioxidant properties

In the current study, the bioactive compounds such as total phenols, flavonoids, hydrolyzable tannins, and gallic acid were extracted from the bark of Swietenia macrophylla using four different solvents such as ethanol, methanol, acetone, and water. Among them, acetone exhibited the highest contents of bioactive compounds. To optimize the extraction process, a statistical approach was adopted using the central composite design (CCD) of response surface methodology (RSM). The five parameters at five different levels were chosen in the design of the experiments. A total of 32 experimental runs given by the design were fitted into the second-order regression model equation. The analysis of the model shows the best fit of the experimental data with an R² of 0.9971 and a model F-value of 191.73. The optimal conditions of acetone concentration (56 %), the volume of acetone (22 mL), agitation speed (173 rpm), extraction temperature (31 °C), and extraction time (28 h) were noted from desirability function and showed a 2.0-fold increase in the contents of bioactive compounds when compared to unoptimized conditions. Further, the antimicrobial activity of 5 % (w/v) extract was tested against two-gram positive strains Bacillus sp, and Staphylococcus aureus, and two-gram negative strains Escherichia coli, and S. marcescens. The extract exhibited the 21 mm and 18 mm clear zone of diameter with 5 mm standard disc against the gram-positive strains tested whereas no clear zone was found against gram-negative strains. Finally, the antioxidant property was electrochemically analyzed using cyclic voltammetry and Differential pulse voltammetry, which confirmed the presence of multiple antioxidants in the extract.     

Extraction and characterization of cellulose single fiber from native Ethiopian Serte (Dracaena steudneri Egler) plant leaf

Biomaterials are renewable sources which are widely distributed, locally accessible, high possibility of recycling and biodegradation behavior. This investigation deals with the extraction and characterizing of new fiber obtained from Serte plant leaf that is found in Ethiopia. The physical, chemical and mechanical characters of the fiber had been tested and comparison with other plant fibers was done for the first time. Optimization of fiber extraction process has been done by varying the extraction variables like NaOH concentration, temperature and extraction time. Fibers possessing 56% cellulose content along with significant amount of hemicellulose, lignin and ash with tensile strength of 330?MPa were obtained. FTIR as well as X-ray diffraction analysis were also done to further analyze the fiber. This new plant leaf fiber can be another alternative resource in place of synthetic fibers depending on their application such as reinforcing polymer matrices.     

固相萃取分离铀

铀是重要的核工业原料,也是一种有较强化学和生物毒性的重金属。从各类含铀水体系中分离和回收铀对缓解铀资源短缺,保护人类健康和生态环境安全都具有重要的科学和实际意义。本文简要回顾和评述了近15年来具有代表性的新型固相萃取材料及其在铀分离方面的应用研究,并对相关材料在铀分离领域的应用前景进行了分析和展望。     

Extraction with long-chain amines-II Extraction and colorimetric determination of chromate

Highly selective extraction of chromate from slightly acidic solutions (0.1-0.2M sulphuric acid) with a chloroform solution of trioctylamine (Alamine 336-S) or trioctylmethylammonium chloride Aliquat 336-S) is described. Many metals such as iron, nickel, cobalt, copper, alluminium, zinc, are not extracted, even if present in large concentrations. Coextraction of vanadium(V) and uranium(VI) is prevented by addition of sodium chloride. Traces of extracted molybdenum are scrubbed with ammonium oxalate. Final determination of chromium is based on measurement of the absorbance of the extract at 445-450 nm.     

Extraction optimization by response surface methodology: Purification and characterization of phytosterol from sugarcane (Saccharum officinarum L.) rind

A green, simple, and effective method for the extraction of sugarcane lipids from sugarcane rind was investigated by response surface methodology. The optimum conditions of technological progress obtained through response surface methodology were as follows: liquid‐to‐solid ratio 7.94: 1 mL/g, extraction temperature 50°C and extraction time 5.98 h. The practical sugarcane lipids extraction yield was 6.55 ± 0.28%, which was in good consistence with the predicted extraction yield of 6.47%. The results showed that the sugarcane lipids extraction yield obtained in optimum conditions increased by 1.16～7.28‐fold compared to the yields obtained in single‐factor experiments. After saponification and SPE steps, the nonsaponifiable fraction of sugarcane lipids was analyzed by gas chromatography with mass spectrometry and high‐performance liquid chromatography. β‐Sitosterol, stigmasterol, and campesterol were the prevailing phytosterols in the sample, while fucosterol, gramisterol, stigmast‐7‐en‐3‐ol, (3β,5α,24S)‐, stigmasta‐4,6,22‐trien‐3α‐ol, and cholest‐8(14)‐en‐3β‐ol acetate were also identified as minor steroids. Furthermore, the content of β‐sitosterol and a mixture of campesterol and stigmasterol (quantified by high‐performance liquid chromatography) was 44.18 mg/100 g dry weight and 43.20 mg stigmasterol/100 g dry weight, respectively. Our results indicate that sugarcane rind is a good source of phytosterol.     

Gene transfer using liposome-complexed adenovirus seems to overcome limitations due to coxsackievirus and adenovirus receptor-deficiency of cancer cells, both in vitro and in vivo

Use of adenoviruses as vehicle for gene therapy requires that target cells express appropriate receptors such as coxsakievirus and adenovirus receptor (CAR). We show here that CAR-deficiency in cancer cells, that limits adenoviral gene delivery, can be overcome by using adenovirus complexed with the liposome, Ad-PEGPE [1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-[methoxy(poly-ethylene glycol)-2000]. We first confirmed that CT-26 mouse colon cancer cells are deficient in CAR by RT-PCR, and then showed that CT-26 cells infected with Ad-GFP/PEGPE exhibited highly enhanced expression of green fluorescent protein (GFP), compared with those infected with Ad-GFP. GFP expression depends on the dose of liposome and adenovirus. Luciferase expression in livers treated with Ad-luc/PEGPE was about 1,000-fold less than those infected with Ad-luc. In a liver metastasis mouse tumor model developed by intrasplenic injection of CT-26 cells, luciferase expression following i.v. injection of Ad-luc/PEGPE was significantly higher in tumors than in adjacent non-neoplastic liver. Following systemic administration of Ad-GFP/PEGPE, GFP expression increased in tumors more than in adjacent liver while the reverse was true following administration of Ad-GFP. In the latter case, GFP expression was higher in liver than in tumors. This study demonstrates that systemic delivery of PEGPE-adenovirus complex is an effective tool of adenoviral delivery as it overcomes limitation due to CAR deficiency of target cells while reducing hepatic uptake and enhancing adenoviral gene expression in tumors.     

西藏红景天超临界流体萃取及萃取物的GC-MS分析

探讨了西藏红景天的超临界流体萃取工艺,应用GC-MS方法对萃取物成分进行了分析.结果表明,最佳提取工艺条件为:夹带剂乙醇的体积分数为85%,萃取温度为55℃,萃取压力为30 MPa,萃取时间为2 h.此条件下红景天萃取物得率为5.65%.GC-MS分析鉴定出32种组分,主要为醇类、酯类、烷烃、烯烃等化合物,并应用峰面积归一化法测定了其相对含量.     

二氢槲皮素的提取及抗氧化性研究

采用浸提法,分别用水、丙酮-水作为提取溶剂从落叶松中提取二氢槲皮素,通过L9(34)正交实验优化最佳提取条件;研究不同油脂中二氢槲皮素的抗氧化效果;比较Vc、BHT、EDTA、柠檬酸对二氢槲皮素的抗氧化协同作用.结果表明,以水作为溶剂的最佳提取条件为:提取温度90 ℃、料液比1:12(g/mL)、提取时间120 min...