Effects of external electromagnetic field on binodal curve of (water + propionic acid + dichloromethane) ternary system

The effects of an external electromagnetic field on the binodal curve of the (water + propionic acid + dichloromethane) ternary system was investigated at 91.3 kPa and T = (294.15 and 284.15) K. The experimental binodal curve values for the ternary system were obtained by the cloud point method using a new setup with a flat capacitor. The effects of variation of frequencies and amplitude of voltages of the applied external electromagnetic field on the binodal curve results have been evaluated. The results obtained indicate that the heterogeneous two-phase area increases with increasing frequency of the applied external electromagnetic field. At constant frequency, a similar effect has been found by increasing the amplitude of the voltage of the applied external electromagnetic field. The comparison between the results obtained for this work with those reported in previous work indicates that the treatment efficiency in liquid–liquid extraction process of (water + propionic acid + dichloromethane) ternary system can be governed by the applied external electromagnetic field.     

Phase equilibria for liquid mixtures of (benzonitrile + a carboxylic acid + water) atT = 298.15 K

(Liquid  +  liquid) equilibrium data are presented for mixtures of {benzonitrile(1)  +  acetic acid or propanoic acid or butanoic acid or 2-methylpropanoic acid or pentanoic acid or 3-methylbutanoic acid(2)  +  water(3)} atT =  298.15 K. The relative mutual solubility of each of the carboxylic acids is higher in the benzonitrile layer than in the aqueous layer. The influence of 3-methylbutanoic acid, pentanoic acid, 2-methylpropanoic acid, and butanoic acid on the solubility of the hydrocarbons in benzonitrile is greater than that of the acetic and propanoic acids. Three three-parameter equations have been fitted to the binodal curve data. These equations are compared and discussed in terms of statistical consistency. The NRTL and UNIQUAC models were used to correlate the experimental tie lines and to calculate the phase compositions of the ternary systems. The NRTL equation fitted the experimental data far better than the UNIQUAC equation. Selectivity values for solvent separation efficiency were derived from the tie line data.     

(Liquid + liquid) equilibria of the (water + butyric acid + dodecanol) ternary system

(Liquid + liquid) equilibrium (LLE) data for the (water + butyric acid + dodecanol) ternary system have been determined experimentally at T = (298.2, 308.2 and 318.2) K. Complete phase diagrams were obtained by determining binodal curves and tie lines. The reliability of the experimental tie lines was confirmed by using the Othmer–Tobias correlation. The UNIFAC method was used to predict the phase equilibrium in the ternary system using the interaction parameters determined from experimental data of CH₃, CH₂, COOH, OH and H₂O functional groups. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) equilibria of (water + propionic acid + diethyl succinate or diethyl glutarate or diethyl adipate) ternary systems

(Liquid + liquid) equilibrium (LLE) data of the solubility (binodal) curves and tie-line end compositions were examined for {water (1) + propionic acid (2) + diethyl succinate or diethyl glutarate or diethyl adipate (3)} at T = 298.15 K and 101.3 ± 0.7 kPa. The relative mutual solubility of the propionic acid is higher in the dibasic esters layers than in the aqueous layers. The reliability of the experimental tie-line data was confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems was predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) equilibria for ternary mixtures of (methanol or ethanol + toluene or m-xylene + n-dodecane)

(Liquid + liquid) equilibrium (LLE) results for the ternary mixtures of (methanol or ethanol + toluene or m-xylene + n-dodecane) at three temperatures (298.15, 303.15 and 313.15) K are reported. The compositions of liquid phases at equilibrium were determined by g.l.c. measurements and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of methanol and ethanol are calculated and compared to suggest which alcohol is more suitable for extracting the aromatic hydrocarbons (toluene or m-xylene) from n-dodecane. The phase diagrams for the ternary mixtures including both the experimental and correlated tie lines are presented. From the phase diagrams and the selectivity factors it is concluded that methanol has a higher efficiency as a solvent in extraction of aromatic hydrocarbon from alkane mixtures.     

Liquid–liquid equilibria of the ternary system water + acetic acid + dimethyl succinate

Liquid–liquid equilibrium (LLE) data of water + acetic acid + dimethyl succinate were measured at 298.2, 308.2, and 318.2 K. Complete phase diagrams were obtained by determining binodal curves and tie lines. The reliability of the experimental tie line data was confirmed by using the Othmer–Tobias correlation. The UNIFAC and modified UNIFAC model were used to predict the phase equilibrium data in the ternary system. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) equilibria of (water + propionic acid + dibasic esters) ternary systems

(Liquid + liquid) equilibrium (LLE) data for the solubility curves and tie-line compositions were examined for mixtures of {water (1) + propionic acid (2) + dimethyl succinate or dimethyl glutarate or dimethyl adipate (3)} at T = 298.15 K and atmospheric pressure, (101.3 ± 0.7) kPa. The relative mutual solubility of the propionic acid is higher in the dibasic esters phases than in the aqueous phase. The reliability of the experimental tie-line data were confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems were predicted by UNIFAC and modified UNIFAC methods. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

Quaternary liquid–liquid equilibrium for water + 1-propanol + cesium sulfate + cesium chloride at 25 °C

Liquid–liquid equilibria for the quaternary system water + 1-propanol + cesium sulfate + cesium chloride were measured at 25 °C. The binodal curves and tie lines for quaternary system have been determined in order to investigate salting effects. Experimental tie lines were compared with values predicated by a modification of the Eisen–Joffe equation.     

Ternary (liquid + liquid) equilibria for mixtures of (methanol + aniline + n-octane or n-dodecane) at T = 298.15 K

(Liquid + liquid) equilibrium (LLE) data for the ternary mixtures of (methanol + aniline + n-octane) and (methanol + aniline + n-dodecane) at T = 298.15 K and ambient pressure are reported. The compositions of liquid phases at equilibrium were determined and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of methanol for the extraction of aniline from the (aniline + n-octane or n-dodecane) mixtures are calculated and compared. Based on these comparisons, the efficiency of methanol for the extraction of aniline from (aniline + n-dodecane) mixtures is higher than that for the extraction of aniline from (aniline + n-octane) mixtures. The phase diagrams for the ternary mixtures including both the experimental and correlated tie lines are presented. From the phase diagrams and the selectivity factors, it is concluded that methanol may be used as a suitable solvent in extraction of aniline from (aniline + n-octane or n-dodecane) mixtures.     

Influence of temperature on the (liquid + liquid) equilibria of {3-methyl pentane + cyclopentane + methanol} ternary system at T = (293.15, 297.15, and 299.15) K

In order to show the influence of temperature on the (liquid + liquid) equilibria (LLE) of the {3-methyl pentane (1) + cyclopentane (2) + methanol (3)} ternary system, equilibrium results at T = (293.15, 297.15, and 299.15) K are reported. The effect of the temperature on the (liquid + liquid) equilibrium is determined and discussed. Experimental results show that this ternary system is completely homogeneous beyond T = 300 K. All chemicals were quantified by gas chromatography using a thermal conductivity detector. The tie line results were satisfactorily correlated by the Othmer and Tobias method, and the plait point coordinates for the three temperatures were estimated. Experimental values for the ternary system are compared with values calculated by the NRTL and UNIQUAC equations, and predicted by means of the UNIFAC group contribution method. It is found that the UNIQUAC and NRTL models provide similar good correlations of the solubility curve at these three temperatures. Finally, the UNIFAC model predicts binodal band type curves in the range of temperatures studied here, similar to those observed for systems classified by Treybal as type 2, instead of type 1 as experimentally observed. Distribution coefficients were also analysed through distribution curves.     

(Liquid + liquid) equilibria of (water + butyric acid + esters) ternary systems

(Liquid + liquid) equilibrium (LLE) data of the solubility (binodal) curves and tie-line end compositions were examined for mixtures of {water (1) + butyric acid (2) + ethyl propionate or dimethyl phthalate or dibutyl phthalate (3)} at T = 298.15 K and (101.3 ± 0.7) kPa. The relative mutual solubility of the butyric acid is higher in the layers of esters than in the aqueous layer. The reliability of the experimental tie-line data was confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems were predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) equilibria of (water + lactic acid + alcohol) ternary systems

(Liquid + liquid) equilibrium (LLE) measurements of the solubility (binodal) curves and tie-line end compositions were carried out for {water (1) + lactic acid (2) + octanol, or nonanol, or decanol (3)} at T = 298.15 K and 101.3 ± 0.7 kPa. The relative mutual solubility of lactic acid is higher in the water layers than in the organic layers. The reliability of the experimental tie-line data was confirmed by using the Othmer–Tobias correlation. The LLE results for the ternary systems were predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

(Liquid + liquid) equilibria of (water + butyric acid + dibasic esters) ternary systems

(Liquid + liquid) equilibrium (LLE) data of the solubility (binodal) curves and tie-line end compositions were examined for mixtures of {water (1) + butyric acid (2) + dimethyl succinate or dimethyl glutarate or dimethyl adipate (3)} at T = 298.15 K and p = (101.3 ± 0.7) kPa. The relative mutual solubility of the butyric acid is higher in the dibasic esters layers than in the aqueous layer. The reliability of the experimental tie-line data was confirmed by using the Othmer–Tobias correlation. The LLE data of the ternary systems were predicted by UNIFAC method. Distribution coefficients and separation factors were evaluated for the immiscibility region.     

Quaternary liquid–liquid equilibria for systems of {(water + methanol or ethanol) + m-xylene + n-dodecane}

Liquid–liquid equilibrium (LLE) data were determined for the quaternary systems of {(water + methanol or ethanol) + m-xylene + n-dodecane} at three temperatures 298.15, 303.15 and 313.15 K and atmospheric pressure. The composition of liquid phases at equilibrium was determined by gas–liquid chromatography and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of the solvent are calculated and compared. The phase diagrams for the quaternary systems including both the experimental and correlated tie lines are presented.     

Liquid–liquid equilibria of ternary systems (water + carboxylic acid + cumene) at 298.15 K

(Liquid–liquid) equilibrium data for the ternary systems [water + formic acid or acetic acid or propionic acid + cumene (2-phenylpropane, isopropylbenzene)] at 298.15 K are reported. Complete phase diagrams were obtained by determining solubility and the tie-line data. The reliability of the experimental tie-lines was determined through the Othmer–Tobias plots. Distribution coefficients and separation factors were evaluated for the immiscibility region. The tie-line data were compared with the results predicted by the UNIFAC method.     

(Liquid + liquid) equilibria of the (water + propionic acid + Aliquat 336 + organic solvents) at T = 298.15 K

In this work, trioctyl methyl ammonium chloride (Aliquat 336) was studied for its ability to extract propionic acid at various amine concentrations. The extraction of propionic acid with Aliquat 336 dissolved in five single solvents (cyclohexane, hexane, toluene, methyl isobutyl ketone, and ethyl acetate ) and binary solvents (hexane + MIBK, hexane + toluene, and MIBK + toluene) was investigated under various experimental conditions. The loading factors Z, extraction efficiency E and overall particular distribution coefficients were determined. All measurements were carried out at T = 298.15 K. The obtained results and the observed phenomena were discussed by taking into consideration the mechanism of extraction and the concentration of the interaction product in the aqueous phase.     

Excess volumes of mixing in (N,N-dimethylacetamide + methanol + water) and (N,N-dimethylacetamide + ethanol + water) at the temperature 313.15 K

Precise excess volumes of mixing measurements at T = 313.15 K are reported over the whole composition range for binary mixtures: (N,N-dimethylacetamide + water), (N,N-dimethylacetamide + methanol), (N,N-dimethylacetamide + ethanol) and for the ternary mixtures (N,N-dimethylacetamide + methanol + water) and (N,N-dimethylacetamide + ethanol + water). For all the systems, large negative deviations from ideality are observed. The binary results have been fitted using the Redlich–Kister type polynomial. The possibility of predicting the ternary results from the binary ones was examined.     

Volumetric study of (2-methoxyethanol + tetrahydrofuran + cyclohexane) at T=298.15 K

The excess molar volumes V_m^E at T=298.15 have been determined in the whole composition domain for (2-methoxyethanol + tetrahydrofuran + cyclohexane) and for the parent binary mixtures. Data on V_m^E are also reported for (2-ethoxyethanol + cyclohexane). All binaries showed positive V_m^E values, small for (methoxyethanol + tetrahydrofuran) and large for the other ones. The ternary V_m^E surface is always positive and exhibits a smooth trend with a maximum corresponding to the binary (2-methoxyethanol + cyclohexane). The capabilities of various models of either predicting or reproducing the ternary data have been compared. The behaviour of V_m^E and of the excess apparent molar volume of the components is discussed in both binary and ternary mixtures. The results suggest that hydrogen bonding decreases with alcohol dilution and increases with the tetrahydrofuran content in the ternary solutions.     

Isobaric (vapour + liquid + liquid) equilibrium data for (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) systems at 100 kPa

Isobaric (vapour + liquid + liquid) equilibria were measured for the (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) system at 100 kPa.The apparatus used for the determination of (vapour + liquid + liquid) equilibrium data was an all-glass dynamic recirculating still with an ultrasonic homogenizer couple to the boiling flask.The experimental data demonstrated the existence of a heterogeneous ternary azeotrope for both ternary systems. The (vapour + liquid + liquid) equilibria data were found to be thermodynamically consistent for both systems.The experimental data were compared with the estimation using UNIQUAC and NRTL models and the prediction of UNIFAC model.     

(Liquid + liquid) equilibria for ternary mixtures of (alkane + benzene + [EMpy] [ESO4]) at several temperatures and atmospheric pressure

In this work, the separation of benzene from aliphatic hydrocarbons (hexane, or heptane) is investigated by extraction with 1-ethyl-3-methylpyridinium ethylsulphate ionic liquid, [EMpy][ESO₄]. (Liquid + liquid) equilibria (LLE) data are determined for the ternary systems: {hexane (1) + benzene (2) + [EMpy][ESO₄] (3)} at T = (283.15, 293.15, 298.15, and 303.15) K and {heptane (1) + benzene (2) + [EMpy][ESO₄] (3)} at T = (283.15 and 298.15) K and atmospheric pressure. The selectivity and distribution coefficient, derived from the tie line data, were used to determine whether the ionic liquid is a good solvent for the extraction of aromatic from aliphatic compounds. The consistency of the tie line data was ascertained by applying the Othmer–Tobias and Hand equations. The experimental results for the ternary systems were well correlated with the NRTL equation. A study of the temperature effect and the influence of the chain length of the alkanes were realized. The results obtained were compared with other ionic liquids. There are no literature data for the mixtures discussed in this paper.