Microstructures by solvent drop evaporation on polymer surfaces: dependence on molar mass

When a solvent drop evaporates from a polymer surface, it leaves behind a characteristic structure, typically a crater. We deposited toluene drops with a microsyringe onto planar polystyrene (PS) surfaces and analyzed the surface topography after drying. For low molar mass PS (Mw = 20.9-24.3 kDa) dotlike protrusions with a ridge at the periphery formed on the polymer surface. With increasing molar mass the central region decreased in height. At Mw = 29.6-643 kDa a craterlike structure with a depression in the center and a ridge was observed. At even higher molar mass, irregular structures without rotational symmetry occurred. We explain the observed dependence on the molar mass with a different degree of entanglement, leading to different dissolution rates and different diffusion constants.     

Dynamic light scattering in semi-interpenetrating polymer networks based on polyacrylamide and poly(N-vinylcaprolactam)

Semi-interpenetrating networks based on polyacrylamide gel and linear thermosensitive poly(N-vinylcaprolactam) are obtained for the first time and studied via the method of dynamic light scattering. Contributions associated with dynamic fluctuations and frozen inhomogeneities to scattering are determined. It is shown that the ensemble-average scattering intensity strongly depends on the quantity and dimensions of frozen inhomogeneities. As temperature increases, scattering due to both dynamic fluctuations and spatial inhomogeneities tends to increase. At the temperature of the conformational transition of poly(N-vinylcaprolactam), the intensity of scattering increases abruptly, whereas the correlation function assumes the shape of a strongly stretched exponent that corresponds to high relaxation times (??1 s). It is found that the relaxation-time distribution restored with the use of the inverse Laplace transform contains several modes. For all the studied networks, the correlation length of the mode of cooperative motion (the fast mode) is independent of the concentration of poly(N-vinylcaprolactam) and coincides with the correlation length of the mode of collective motion for the polyacrylamide gel.     

Dynamics of 4-benzylamino-7-nitrobenzofurazan in the 1-propanol/water binary solvent system. Evidence for composition-dependent solvent organization

We report on the fluorescence lifetime and rotational diffusion dynamics of 4-benzylamino-7-nitrobenzofurazan (BBD) in a series of 1-propanol/water binary solvent systems. The fluorescence lifetime of BBD increases monotonically with increasing 1-propanol concentration. The rotational diffusion dynamics of BBD also vary with solution 1-propanol content, but this variation is not monotonic. Comparison of the BBD rotational diffusion time constant to solution viscosity and 1-propanol composition reveals the presence of a solution composition dependence of solvent-solute interactions, with a relative decrease in solvent-solute interaction strength for solvent system compositions where the 1-propanol/water azeotrope is known to exist. These data point collectively to the existence of microscopic heterogeneity in these binary solvent systems.     

Excess molar enthalpies for binary mixtures of different amines with water

The isothermal excess molar enthalpies for binary mixtures of different amines with water were measured with a C-80 Setaram calorimeter. The experimental results indicate that the excess molar enthalpy is related to the molecular structure. The experimental excess molar enthalpies were satisfactorily fitted with the Redlich–Kister equation. They were also used to test the suitability of the NRTL model, and the deviations are a little larger than the R–K equation.     

Regulating the morphology of fluorinated non-fullerene acceptor and polymer donor via binary solvent mixture for high efficiency polymer solar cells

Fluorinated non-fullerene acceptors(NFAs) usually have planar backbone and a higher tendency to crystallize compared to their non-fluorinated counterparts, which leads to enhanced charge mobility in organic solar cells(OSCs). However, this selforganization behavior may result in excessive phase separation with electron donors and thereby deteriorate device efficiency.Herein, we demonstrate an effective approach to tune the molecular organization of a fluorinated NFA(INPIC-4 F), and its phase separation with the donor PBDB-T, by varying the casting solvent. A prolonged film drying time encourages the crystallization of INPIC-4 F into spherulites and consequently results in excessive phase separation, leading to a low device power conversion efficiency(PCE) of 8.1%. Contrarily, a drying time leads to fine mixed domains with inefficient charge transport properties,resulting in a moderate device PCE of 11.4%. An intermediate film drying time results in the formation of face-on π-π stacked PBDB-T and INPIC-4 F domains with continuous phase-separated networks, which facilitates light absorption, exciton dissociation as well as balanced charge transport towards the electrode, and achieves a remarkable PCE of 13.1%. This work provides a rational guide for optimizing the molecular ordering of NFAs and electron donors for high device efficiency.     

Nanoprecipitation of poly(methyl methacrylate)‐based nanoparticles: Effect of the molar mass and polymer behavior

The current investigation describes in detail the influence of the polymer molar mass as well as polymer‐solvent interactions on the formation of nanoparticles using the nanoprecipitation methodology. For this purpose, a homologous series of poly(methyl methacrylate)s with molar masses ranging from 7,700 to 274,000 g mol^?1 was prepared. Subsequently nanoprecipitation was performed in an automated and systematic manner using liquid handling robots and a variation of different initial concentrations of the polymers and solvent/nonsolvent ratios. To elucidate information about the polymer behavior in the solvents used for the nanoprecipitation procedure (acetone, tetrahydrofuran), intrinsic viscosity measurements were performed. The nanoparticle formulations were examined in terms of particle size and size distribution, particle shape as well as zeta‐potential. The conditions for the preparation of stable and uniform nanoparticles, regardless of molar mass and hydrodynamic volume of the initial polymer, were determined. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Influence of plasma treatment on the molar mass of poly(ethylene terephthalate) investigated by different chromatographic and spectroscopic methods

The influence of different types of low and atmospheric pressure plasma on poly(ethylene terephthalate) (PET) has been studied in terms of changes in molar mass and molar mass distribution. Apart from a variation of plasma gases (oxygen, helium) different types of plasma (microwave, radio frequency, corona discharge) were used for the plasma surface modification. The changes in molar mass and types of functional end groups of lower molar mass products were investigated by means of matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOFMS), whereas the high-molar mass fraction was analyzed by means of size-exclusion chromatography (SEC). The formation of crosslinked products during exposure to a helium plasma, which emits preponderately energy-rich and intense ultraviolet radiation, was proved by means of thermal field-flow fractionation (ThFFF). This method combined with a multiangle laser light scattering (MALLS) detector allows detection of weakly crosslinked polymers and microgels. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1639–1648, 1998     

Determination of molar mass distribution of poly(tetrafluoroethylene)

High-temperature static and dynamic laser light scattering characterization of polytetrafluoroethylene in perfluorotetracosane has been accomplished after solving the following experimental difficulties: (1) constructing a high-temperature laser light scattering spectrometer which can be operated at a temperature as high as 340 °C, (2) developing a new all-glass apparatus for dissolving and filtering, (3) measuring the refractive index increment of polytetrafluoroethylene in perfluorotetracosane at 325 °C, and (4) establishing a scaling relation between the molecular weight (M) and the translational diffusion coefficient at both infinite dilution and the zero scattering angle from only two broadly distributed polytetrafluoroethylene samples so that we can convert the translational diffusion coefficient distribution to the molecular weight distribution. This paper presents a summary of our published results of the characterization of poly(tetrafluoroethylene), which emphasizes the experimental details of high-temperature laser light scattering and the principle of the transformation from a translational diffusion coefficient distribution to a molecular weight distribution.     

Influence of molar ratios of precursor,catalyst, solvent and water on monolithicity and physical properties of TMOS silica aerogels

In continuation to our earlier work on aerogels, the experimental results on the monolithicity and physical properties of silica aerogels as a function of the molar ratios of tetramethoxysilane (TMOS) precursor, catalyst (NH₄OH), methanol (MeOH) solvent and water, are reported. The molar ratios of NH₄OH/TMOS, MeOH/TMOS and H₂O/TMOS were varied from 7.1 × 10^–6 to 9.6 × 10^–1, 1 to 90 and 1 to 18 respectively. It has been found that larger molar ratios of NH₄OH/TMOS (10^–2), MeOH/TMOS (13 to 60) and H₂O/TMOS (>10) resulted in transparent but cracked aerogels, and very low molar ratios of these combinations gave monolithic but less transparent or opaque aerogels. The best quality silica aerogels, in terms of monolithicity, transparency and low density, have been obtained with TMOS:MeOH:H₂O:NH₄OH in the molar ratio of 1:12:4:3.7 × 10^–3 respectively. The aerogels have been characterized by density, optical transmission, surface area and porosity measurements. The results have been discussed by taking into account the hydrolysis and condensation reactions, and syneresis effects.     

Effect of the composition of binary polar solvent mixtures on dye adsorptivity in the polymer matrix

Sorption and diffusion processes of 1-mercapto-2-naphthol nickel complex in a polymer matrix upon surface dyeing of polymethyl methacrylate are studied by near-IR spectroscopy as a function of dye solution composition and technological parameters of the process. The optimum solution composition and technological regime are selected. The diffusion coefficient is evaluated.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1289–1293, July, 1995.The authors express their gratitude to Dr. Chem. Sci. N. O. Mchedlov-Petrosyan for a series of valuable remarks in his discussion of this work.This work was carried out with financial support from the International Science Foundation (Grant U2V000).     

Reversible melting of high molar mass poly(oxyethylene)

The heat capacity, C_p, of poly(oxyethylene), POE, with a molar mass of 900,000 Da, was analyzed by temperature-modulated differential scanning calorimetry, TMDSC. The high molar mass POE crystals are in a folded-chain macroconformation and show some locally reversible melting, starting already at about 250 K. At 335 K the thermodynamic heat capacity reaches the level of the melt. The end of melting of a high-crystallinity sample was analyzed quasi-isothermally with varying modulation amplitudes from 0.2 to 3.0 K to study the reversible crystallinity. A new internal calibration method was developed which allows to quantitatively assess small fractions of reversibly melting crystals in the presence of the reversible heat capacity and large amounts of irreversible melting. The specific reversibility decreases to small values in the vicinity of the end of melting, but does not seem to go to zero. The reversible melting is close to symmetric with a small fraction crystallizing slower than melting, i.e., under the chosen condition some of the melting and crystallization remains reversing. The collected data behave as one expects for a crystallization governed by molecular nucleation and not as one would expect from the formation of an intermediate mesophase on crystallization. The method developed allows a study of the active surface of melting and crystallization of flexible macromolecules.     

Determination of hydrogen ion activity in various binary dimethylformamide/water and ternary dimethylformamide/dioxane/water solvent systems

The practical pH values in dimethylformamide/water and dimethylformamide/dioxane/water solvent mixtures measured by a pH meter standardized against aqueous buffer solutions do not lie on the conventional scale of hydrogen ion activity referred to the standard state in the corresponding medium (pa^*_H). The values can be converted to pa^*_H by introducing a correction term δ. Values of δ were determined at 25°C. Simple interpolation equations are derived to express the variation of δ with solvent composition. In the ternary mixtures, the results show that the composite medium effect, described by a parameter b=dδ/du, (where u depends on the solvent composition), depends on the ratio of the organic solvent concentrations.     

Influence of solvent type on porosity structure and properties of polymer separator for the Li-ion batteries

Polyethylene-supported polymethyl methacrylate/poly(vinylidene fluoride-co-hexafluoropropylene) separator for gel polymer lithium-ion battery use was prepared with a mixed solvent of n-butanol and acetone. The prepared separator was characterized with scanning electron spectroscopy and X-ray diffraction, and its performance was investigated by electrochemical impedance spectroscopy and battery charge/discharge test. Compared to the separator prepared with acetone, the separator prepared with the mixed solvent shows an enhanced porosity (from 42 to 49 %) and electrolyte uptake (from 104 to 125 %). The ionic conductivity of the corresponding gel polymer electrolyte is improved from 2.81 to 3.39 mS cm^?1, the discharge capacity retention of the LiCoO₂/artificial graphite battery is increased from 95 to 98 % after 100 cycles at 0.5 C, and the discharge capacity of the battery at 1 C increases by 4 %.     

Blends of poly(epsilon-caprolactone) and intermediate molar mass polystyrene as Langmuir films at the air/water interface

Poly(epsilon-caprolactone)/polystyrene (PCL/PS) blends, where nonamphiphilic PS is glassy in the bulk state at the experimental temperature of 22.5 degrees C, are immiscible as Langmuir films at the air/water (A/W) interface. Surface pressure-area per monomer isotherm analyses indicate that the surface concentration of amphiphilic PCL is the only factor influencing the surface pressure below the collapse transition. For PS-rich blends, Brewster angle microscopy (BAM) studies at the A/W interface and atomic force microscopy studies on Langmuir-Schaefer films reveal that PS nanoparticle aggregates formed at very low surface pressures can form networks upon further compression. The morphologies seen in PS-rich blends (networklike rings) are consistent with a recent study of a nonamphiphilic polyhedral oligomeric silsesquioxane (POSS), octaisobutyl-POSS, blended with amphiphilic poly(dimethylsiloxane), suggesting that the nonamphiphilic PS aggregates at the A/W interface produce domains with dipole densities that differ from that of pure PCL. In all composition regimes, the amphiphilic PCL phase tends to spread and form a continuous surface layer at the A/W interface, while simultaneously improving the dispersion of nonamphiphilic PS domains. During film expansion, BAM images show a gradual change in the surface morphology from highly continuous networklike structures (PS-rich blends) to broken ringlike structures (intermediate composition) to small discontinuous aggregates (PCL-rich blends). This study provides valuable information on the morphological evolution of semicrystalline PCL-based polymer blends confined in a "two-dimensional" geometry at the A/W interface and fundamental insight into the influence of microstructure (domain size, phase-separated structures, crystalline morphology, etc.) on the interfacial properties of blends as Langmuir films.     

Crystallization of poly(ethylene oxide) in binary polymer blends: Influence of tacticity of poly(methyl methacrylate)

Kinetics of the crystallization of poly(ethylene oxide) (PEO) from the PEO blends with syndiotactic, atactic, or isotactic poly(methyl methacrylate) (s-, a-, and i-PMMA) was investigated. The isothermal spherulitic growth rates were measured with an optical microscope. The influence of the composition of the blends, the tacticity of PMMA, and temperature on the growth rates were studied. Linear growth rates were observed regardless of the tacticity. The growth rates of spherulites are markedly reduced by a-PMMA and s-PMMA. However the growth rates of PEO are hardly influenced by i-PMMA. Such observations are interpreted by assuming that PEO forms miscible blends with a- and s-PMMA in the molten states, whereas it does not from with i-PMMA.     

Rapid crystallization and thermoreversible gelation of poly(ethylene terephthalate) in polymer/oligomer binary system

Poly(ethylene terephthalate) (PET) was rapidly crystallized through thermoreversible gelation in a liquid ethylene glycol oligomer or in epoxy resin. The solutions formed gel rapidly on cooling. Polarized light microscopy and small-angle light scattering showed that these gels contain large, regular PET spherulites. The gels may be formed by two consecutive processes: the phase separation and crystallization, and gelation by formation of a three-dimensional PET network in the oligomer solvents, where the nodes of the network are PET spherulites. The crystallinity of PET recovered from polymer/oligomer gels is near 72% measured by wide-angle X-ray diffraction method, which is about 20% higher than PET samples crystallized by solution crystallization in small molecule solvent, high temperature annealing, and stretching techniques. It takes only a few minutes to form the highly crystalline phase PET in the PET/oligomer system, and the crystallinity of the dried gel is independent of the concentration of the original solution. Excimer-fluoresence and Raman spectroscopic studies indicated that PET recovered from the gels are in an ordered state with few chain entanglements. The entanglement density of the recovered PET recovered from a 20 wt % solution in ethylene glycol oligomer is as low as that of freeze-extracted PET from a 0.5 wt % solution in phenol. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1219–1225, 1998     

Influence of binary surfactant mixtures on the rheology of associative polymer solutions

Hydrophobically modified alkali-soluble emulsion polymers (HASE) are a class of comblike associative polymers that can impart high viscosities to aqueous solutions. The rheology of HASE solutions can be tuned by the addition of surfactants, such as nonylphenol ethoxylates (NP e), where e is the length of the hydrophilic (ethoxylate) chain. While previous studies have considered individual surfactants, our focus here is on binary surfactant mixtures. We find that equimolar NP4-NP12 mixtures significantly enhance the zero-shear viscosities of HASE solutions as compared to equivalent amounts of NP8, especially at high overall surfactant concentrations. Dynamic rheological measurements suggest that the higher viscosities are due to increases in the lifetime of hydrophobic junctions in the polymer-surfactant network. In contrast to the above results, equimolar NP4-NP8 mixtures are rheologically identical to equivalent solutions of NP6. The differences between the two sets of mixtures are further correlated with cloud point measurements and thereby with the overall hydrophilic-lipophilic balance (HLB) of the surfactant system.     

Electroclinic behaviour of polymer doped low molar mass ferroelectric liquid crystals

Abstract

Recently there has been much interest in the electroclinic effect due to its potential application in high speed optical modulators and grey scale displays. In present materials, however, the electroclinic effect is very dependent on temperature and falls off rapidly with increasing temperature. This limits the useful device operating range. In this paper the electroclinic behaviour of new, side chain polymer doped, low molar mass ferroelectic liquid crystal mixtures is reported. By measuring the rate of change of the electroclinic coefficient with temperature it is shown that the temperature range over which the electroclinic effect exists increases with polymer concentration. Data are also presented on electroclinic response times.     

Electroclinic behaviour of polymer doped low molar mass ferroelectric liquid crystals

Recently there has been much interest in the electroclinic effect due to its potential application in high speed optical modulators and grey scale displays. In present materials, however, the electroclinic effect is very dependent on temperature and falls off rapidly with increasing temperature. This limits the useful device operating range. In this paper the electroclinic behaviour of new, side chain polymer doped, low molar mass ferroelectic liquid crystal mixtures is reported. By measuring the rate of change of the electroclinic coefficient with temperature it is shown that the temperature range over which the electroclinic effect exists increases with polymer concentration. Data are also presented on electroclinic response times.