Synthesis and gas permeation properties of poly(4-methyl-2-pentyne)

Poly(4-methyl-2-pentyne) [PMP] is an amorphous, glassy, di-substituted acetylene-based polymer. PMP has a low density of 0.78 g/cm³ and a high fractional free volume of 0.28. The permeabilities for helium, hydrogen, nitrogen, oxygen, carbon dioxide, methane, ethane, propane, and n-butane were determined at temperatures from 20 to 65°C and pressures from 10 to 150 psig. PMP is the most permeable purely hydrocarbon-based polymer known; its permeabilities are only exceeded by poly(1-trimethylsilyl-1-propyne) [PTMSP] and poly(1-trimethylgermyl-1-propyne) [PTMGeP]. The oxygen permeability of PMP at 25°C is 2700 × 10⁻¹⁰ cm³(STP) cm/cm² s cmHg and the nitrogen permeability is 1330 × 10⁻¹⁰ cm³(STP) cm/cm² s cmHg. The high gas permeabilities in PMP result from its very high free volume, and probably, interconnectivity of the free-volume-elements. For a glassy polymer, PMP exhibits unusual organic vapor permeation properties. Permeabilities in PMP are higher for large, condensable gases, such as n-butane, than for small, permanent gases such as helium. The permeabilities of condensable gases and permanent gases decrease as the temperature is increased. This behavior is completely unexpected for a glassy polymer and has been observed previously in only high-free-volume glassy PTMSP.     

Crosslinking and stabilization of nanoparticle filled PMP nanocomposite membranes for gas separations

Poly(4-methyl-2-pentyne) (PMP) has been crosslinked using 4,4′-(hexafluoroisopropylidene) diphenyl azide (HFBAA) to improve its chemical and physical stability over time. Crosslinking PMP renders it insoluble in good solvents for the uncrosslinked polymer. Gas permeability and fractional free volume (FFV) decreased as crosslinker content increased, while gas sorption was unaffected by crosslinking. Therefore, the reduction in permeability upon crosslinking PMP was due to decrease in diffusion coefficient. Compared to the pure PMP membrane, the permeability of the crosslinked membrane is initially reduced for all gases tested due to the crosslinking. By adding nanoparticles (FS, TiO₂), the permeability is again increased; permeability reductions due to crosslinking could be offset by adding nanoparticles to the membranes. Increased selectivity is documented for the gas pairs O₂/N₂, H₂/N₂, CO₂/N₂, CO₂/CH₄ and H₂/CH₄ using crosslinking and addition of nanoparticles. Crosslinking is successful in maintaining the permeability and selectivity of PMP membranes and PMP/filler nanocomposites over time.     

Silica filled poly(4-methyl-2-pentyne) nanocomposite membranes: Similarities and differences with poly(1-trimethylsilyl-1-propyne)–silica systems

The performance of poly(4-methyl-2-pentyne) (PMP)/silica nanocomposites was studied for membranes with a filler content between 10 and 40 wt%. An increase in permeability and a constant vapor selectivity were measured with increasing filler content. The constant selectivity was in contrast to earlier published results for silica filled poly(1-trimethylsilyl-1-propyne) (PTSMP) membranes. Therefore, a comparison between both materials was made. Free volume sizes and interstitial mesopore sizes were determined by use of positron annihilation lifetime spectroscopy (PALS) and image analysis was performed on transmission electron microscopy (TEM) pictures of both materials. Although both materials possessed interstitial mesopores, a difference in membrane structure was noticed, explaining the difference in membrane performance.     

Effects of physical aging on solubility,diffusivity, and permeability of propane and n-butane in poly(4-methyl-2-pentyne)

The effects of physical aging on the solubility, diffusivity, and permeability of propane and n-butane in a hydrocarbon-based disubstituted polyacetylene, poly(4-methyl-2-pentyne) (PMP), were studied. As the relative pressure of propane and n-butane increased, the solubility of both hydrocarbons increased. Like other glassy polymers, the sorption isotherms for propane and n-butane in all PMP films were concave to the relative pressure axis, indicating dual-mode sorption behavior. The diffusion of propane and n-butane in PMP followed typical Fickian diffusion in a plane sheet. The propane diffusivity in both the unaged and aged films increased with increasing concentration of propane sorbed in the film. The n-butane diffusivity in aged films also increased with increasing n-butane concentration. However, unaged films showed the opposite behavior: the diffusivity decreased with increasing n-butane concentration. These diffusion phenomena are a consequence of the interplay between thermodynamic and mobility factors. The permeabilities of propane and n-butane decreased monotonically with increasing penetrant concentration, similar to the behavior observed in other common glassy polymers. The relaxation of the nonequilibrium excess free volume in PMP films induced the decrease in both solubility and diffusivity. As a result, the permeability of propane and n-butane in PMP decreased upon physical aging. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2407–2418, 2004     

Living Polymerization of 1-Trimethylsilyl-1-propyne and 4-Methyl-2-pentyne by NbCl5-Based Catalysts

Sequential homopolymerization of disubstituted acetylenes 1-trimethylsilyl-1-propyne and 4-methyl-2-pentyne by NbCl₅–Ph₃SiH was investigated and the main evidence of living polymerization, namely, continuation of chain propagation after addition of a new portion of monomer was observed. AB and BA type block copolymers of 1-trimethylsilyl-1-propyne and 4-methyl-2-pentyne were synthesized by sequential polymerization of these monomers in presence of NbCl₅–based catalytic systems.     

An electrooptical method for studying the mean length of stereoblocks in poly(1-trimethylsilyl-1-propynes) and poly(1-trimethylgermyl-1-propynes)

It was shown that equilibrium electrooptical properties (the Kerr effect) in solutions of disubstituted polyacetylenes poly(1-trimethylsilyl-1-propyne) and poly(1-trimethylgermyl-1-propyne) are related to the dipole structure of these polymers that is associated with the partial spiralization of their chains. A method of estimating the length of monomer unit sequences occurring in the same spatial configuration (stereoblocks) was developed. This method is based on the experimental measurement of the specific Kerr constant of disubstituted polyacetylenes. The sizes of stereoblocks in polymer chains that were synthesized with the use of various catalysts and that differ in the mean ratio of trans: cis C=C bonds, as estimated by the electrooptical method, were compared with the X-ray diffraction data on the same film polymers. There was good agreement between the results obtained by both methods.     

用带不同侧链的双取代聚乙炔衍生物增溶多壁碳纳米管

采用不同的双取代聚乙炔与多壁碳纳米管复合,通过π-π相互作用和聚合物链缠绕实现了对碳纳米管的增溶.这种方法对碳纳米管的结构没有损害,而且包覆到碳纳米管表面的双取代聚乙炔也显示了自身的荧光发射特性.     

π-conjugated columnar polyacetylenes prepared with Rh complex catalysts

Highly stereospecific polymerization of monosubstituted acetylenes was carried out using the Rh complex, [Rh(norbornadiene)Cl]₂ catalysts. The resulting polyacetylenes were characterized in detail by ¹HNMR, ESR, laser Raman, diffuse reflective UV, and wide angle X-ray diffraction methods. The data showed that the Rh complex were the preferred catalyst to selectively yield the corresponding cis-transoid polymers even at room temperature when alcohol, triethylamine or water was used as the polymerization solvent. Additionally, the resulting cis polyacetylenes were found to have a helical form whose polymer is amorphous or composed of pseudohexagonal structures called π-conjugated columnar as self-assembly or super structure. Further compression of the amorphous cis polymers resulted in cis to trans isomerization at room temperature under vacuum, breaking rotationally the cis C=C bonds giving π-radicals called solitons as the origin of a polymer magnet. On the other hand, the π-conjugated columnar was also found to show an extremely longer wavelength absorption compared with that of the amorphous one, although the absorption maximum was shifted to a shorter wavelength when the columnar was destroyed by the compression. Therefore, the formation of the π-conjugated columnar can be considered as a new and quite useful control method concerning color of such conjugated polymers, i.e., a new concept concerning the color of conjugated polymers.     

Synthesis and three-dimensional structures of the cis and trans isomers of 3-methyl-1-tert-butyl-4-acetyl- and 3-methyl-1-tert-butyl-4-carbomethoxy-4-piperidols

The cis and trans isomers of 3-methyl-1-tert-butyl-4-acetyl- and 3-methyl-1-tertbutyl-4-carbomethoxy-4-piperidols, the three-dimensional configurations of which were established by means of their IR and UV spectra, were synthesized in order to study the interrelationship between the structure and reactivity of stereoisomeric piperidines.Translated from Khimiya Geterotsiklicheskikh Soedinenni, No.12, pp. 1659–1665, December, 1973.     

Molecular simulation and experimental study of substituted polyacetylenes: fractional free volume, cavity size distributions and diffusion coefficients

Glassy, disubstituted acetylene-based polymers exhibit extremely high gas permeabilities and high vapor/gas selectivities, which is quite unusual for conventional glassy polymers such as polysulfone. Diffusion coefficients of poly[1-phenyl-2-[p-(trimethylsilyl)phenyl]acetylene] (PTMSDPA) and poly[diphenylacetylene] (PDPA) were obtained using both molecular simulation and experimental techniques. PTMSDPA, a disubstituted glassy acetylene-based polymer, exhibits higher diffusivity than its desilylated analogue, PDPA. Simulation results are in good agreement with experimental data. Cavity size (free volume) distributions of both polymers are also obtained using an energetic-based algorithm (in't Veld et al., J. Phys. Chem. B 2000, 104, 12028) developed recently. Larger cavities in PTMSDPA contribute to its higher diffusivity, and higher permeability.     

Chromatographic analysis of cis/trans carotenoid isomers.

Cis/trans configurations of carotenoids are known to effect the biochemistry of carotenoids in certain situations. Methodology for separating carotenoid cis/trans isomers is of importance to nutritionists and food scientists because cis isomers of provitamin A carotenoids have lower provitamin A activities than the all-trans form. Traditional food processing and preservation methods, especially thermal treatments, induce the formation of cis isomeric forms. However, many challenges, are apparent for identifying and analyzing cis/trans isomers present in foods and other biological tissues. The development of current chromatographic methods for the separation of carotenoid cis/trans isomers is reviewed. For the separation of beta-carotene isomers, most procedures employ either Ca(OH)2 or Vydac C18 columns. In general, polymeric C18 columns allow for the detection of cis carotenes, while monomeric C18 columns provide for some separation of certain xanthophylls. The main cis isomers detected in foods are the 13-cis and 9-cis forms, although other forms have also been found (mainly 15-cis and various di-cis isomers). More studies involving the metabolism and physiological consequences of cis/trans isomers in the diet are needed. However, due to limitations in current techniques, further method development in the area of separation, detection and quantitation of cis/trans carotenoid isomers will be required.     

Recent developments in polyetherimide membrane for gas separation

Polyetherimide (PEI) is an extraordinary type of polyimide with excellent thermal and mechanical properties. The polymer is also gas permeable and is considered one of the best membranes for gas separation. Despite the high selectivity, PEI suffers from low permeability due to the trade‐off between phenomena in polymers. To overcome this limitation, fillers are added during the membrane preparation to create voids for better gas transport. In this paper, permeability and selectivity data of PEI membranes for the separation of oxygen, carbon dioxide, and helium are discussed. The paper also summarizes the reported studies for adding fillers to improve the membrane performance.     

Preparative separation of isomeric and stereoisomeric dicarboxylic acids by pH-zone-refining counter-current chromatography

This work involves the preparative separation of some isomeric dicarboxylic acids using pH-zone-refining counter-current chromatography (CCC), a relatively new preparative technique for the separation of ionizable compounds. The paper concentrates especially on the separation of a synthetic mixture of closely related cis and trans pairs of 1-methyl- and 1,3-dimethyl-1,3-cyclohexanedicarboxylic acids. The elution sequence of the isomers is discussed in terms of their relative acidities (pK(a) values) in solution and gas phase, hydrophobicities, and steric configuration. Two possible explanations are suggested for the mechanism of separation. They both involve the amount of retainer acid used, as it affects the separation and plays a role in the chemohydrodynamic equilibrium of the dicarboxylic acids in the column.     

Poly[1‐(trimethylgermyl)‐1‐propyne] and poly[1‐(trimethylsilyl)‐1‐propyne] with various geometries: Their synthesis and properties

The polymerization of 1,2‐disubstituted acetylenes [1‐(trimethylgermyl)‐1‐propyne and 1‐(trimethylsilyl)‐1‐propyne] initiated by Nb‐ and Ta‐based catalytic systems was studied within a wide temperature range (?10 to +80 °C) with solvents (cyclohexane, CCl₄, toluene, anisol, and n‐chlorobutane) with variable dielectric constants (2.023–7.390). Conditions ensuring the synthesis of poly[1‐(trimethylsilyl)‐1‐propyne] (PTMSP) containing 20–80% cis units and poly[1‐(trimethylgermyl)‐1‐propyne] (PTMGP) containing 3–65% cis units were determined. The PTMSP and PTMGP samples were amorphous, exhibited a two‐phase structure characterized by the presence of less ordered regions and regions with an enhanced level of ordering, and differed in solubility. A correlation was found between the cis/trans ratio and the morphology, the geometrical density of PTMSP and PTMGP films, and the gas permeability of the polymers. The gas permeability and solubility behavior of PTMSP and PTMGP were examined in terms of the molecular characteristics of the polymer samples (the thermodynamic Kuhn segment and the Kerr electrooptic effect). It was demonstrated that the gas permeability, as well as the solubility of the polymers, was defined by their supramolecular ordering, which depended on the lengths of continuous sequences composed of units of analogous microstructures and on the flexibility of macrochains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2133–2155, 2003     

MORPHOLOGIES AND GAS SEPARATION PROPERTIES OF MELT-SPUN ASYMMETRIC POLY(4-METHYL-1-PENTENE)HOLLOW FIBER MEMBRANES*

Poly(4-methyl-1-pentene) (PMP) hollow fiber membranes were prepared by the melt-spun and cold-stretch(MSCS) method. Scanning electronic microscopy (SEM) was used to characterize the section and surface structures of themembranes with special asymmetric structure. The preliminary results of gas permeation measurements indicated that the resultant hollow fiber membranes have the potential ability for oxygen/nitrogen separation.     

Transport of organic vapors through poly(1-trimethylsilyl-1-propyne)

Poly(1-trimethylsilyl-1-propyne) [PTMSP], a high-free-volume glassy polymer, has the highest gas permeability of any known synthetic polymer. In contrast to conventional, low-free-volume, glassy polymers, PTMSP is more permeable to large, condensable organic vapors than to permanent gases. The organic-vapor/permanent-gas selectivity of PTMSP based on pure gas measurements is low. In organic-vapor/permanent-gas mixtures, however, the selectivity of PTMSP is much higher because the permeability of the permanent gas is reduced dramatically by the presence of the organic vapor. For example, in n-butane/methane mixtures, as little as 2 mol% n-butane (relative n-butane pressure 0.16) lowers the methane permeability 10-fold from the pure methane permeability. The result is that PTMSP shows a mixed-gas n-butane/methane selectivity of 30. This selectivity is the highest ever observed for this mixture and is completely unexpected for a glassy polymer. In addition, the gas mixture n-butane permeability of PTMSP is considerably higher than that of any known polymer, including polydimethylsiloxane, the most vapor-permeable rubber known. PTMSP also shows high mixed-gas selectivities and vapor permeabilities for the separation of chlorofluorocarbons from nitrogen. The unusual vapor permeation properties of PTMSP result from its very high free volume - more than 20% of the total volume of the material. The free volume elements appear to be connected, forming the equivalent of a finely microporous material. The large amount of condensable organic vapor sorbed into this finely porous structure causes partial blocking of the small free-volume elements, reducing the permeabilities of the noncondensable permanent gases from their pure gas values.     

Photoisomerization and Emission Properties of trans‐ and cis‐Poly(dimethylsilylenephenylenevinylene)s

The photoirradiation of trans‐ and cis‐poly(dimethylsilylenephenylenevinylene)s gave cis‐rich mixtures at equilibrium states. The degree of the photoisomerization could be exactly evaluated by comparing the UV spectra of the photoirradiated solutions with those of the trans and cis polymers. The geometric configuration of the trans and cis polymers was thermally stable and hardly changed even though they were heated. The trans and cis polymers exhibited different emission properties; e.g., trans polymer: λ_max = 400 nm, quantum yield = 3.4×10^–3; cis polymer: λ_max = 380 nm, quantum yield = 1.5×10^–3.     

Hydrocarbon solubility,permeability, and competitive sorption effects in polymer of intrinsic microporosity (PIM‐1) membranes

The sorption and permeation of pentane, hexane, and toluene through highly permeable polymer of intrinsic microporosity (PIM‐1) membranes were investigated. It was established that the hydrocarbons sorbed strongly within the micro‐void regions of the PIM‐1 membrane. The sorption concentration was similar for the paraffins, pentane and hexane, but greater for aromatic toluene at high vapor activities. The magnitude of the hydrocarbon permeability was associated with the critical temperature of the hydrocarbon. The PIM‐1 membrane displayed selectivity for the three hydrocarbons over CO₂. As a consequence, the presence of the three hydrocarbons dramatically reduced the permeability of CO₂ and N₂ under mixed gas–vapor conditions to 68%–95% below the dry gas value. For all three hydrocarbons the N₂ permeability was more strongly impacted than CO₂ permeability, and hence the ideal CO₂/N₂ selectivity of PIM‐1 increased. It was determined that CO₂ and N₂ solubility decreased because of hydrocarbon competitive sorption while CO₂ and N₂ diffusivity also decreased because of anti‐plasticization, which was due to the presence of hydrocarbon clusters within the membrane structure. There was a clear correlation between the magnitude of anti‐plasticization and the critical temperature of the hydrocarbon. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 397–404     

2-Methyl-4-(o-nitrobenzylidene)oxazol-5-ones

The cis and trans isomers of 2-methyl-4-(o-nitrobenzylidene)oxazol-5-one have been obtained. On reduction, the cis isomer formed 3-acetamidoquinolin-2-ol, and the trans isomer formed 4-(o-aminobenzylidene)-2-methyloxazol-5-one. Details of the IR, UV, PMR, and mass spectra of the compounds obtained are given.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 5, pp. 615–617 (1985).     

The observation of cis residues in poly(L-proline) in aqueous solution.

Proton Fourier transform NMR spectra at 270 MHz were obtained for three different molecular weight samples of poly(L-proline) in D2O. A weak, but clearly discernable, resonance at 4.3 ppm was observed in each case with an integrated intensity about 2-3% of the Calpha trans proton resonance. Based on the Torchia-Bovey assignment this resonance is attributed to the Calpha cis proton. The presence of cis residues, even in this small concentration, necessitates a reexamination of the conformational properties of this polymer. Definite conclusions cannot be reached from spectra obtained in organic solvents because of the much smaller separation between the cis and trans resonances.