纳米薄层HZSM-5分子筛催化甲醇制丙烯

在合成系列硅铝比纳米薄层HZSM-5分子筛的基础上,研究了纳米薄层HZSM-5分子筛催化甲醇制丙烯(MTP)的反应性能.在固定床微反装置上详细考察了工艺条件对纳米薄层HZSM-5分子筛催化性能的影响,同时与纳米HZSM-5分子筛对MTP反应的催化性能进行了比较.结果表明,纳米薄层HZSM-5分子筛具有较高的目的产物选择性和较长的催化寿命.在适宜硅铝比(n(SiO2)/n(Al2O3)=213)和反应条件下(温度470°C,甲醇质量空速为3 h-1),丙烯的选择性达到46.7%,三烯(乙烯、丙烯和C4烯烃)选择性达到78.7%.其中,丙烯/乙烯的质量比可达到6.5,是纳米HZSM-5分子筛的2倍,而芳烃的选择性比纳米分子筛明显降低.这是因为纳米薄层HZSM-5分子筛比纳米HZSM-5分子筛具有较宽的(010)晶面、较大的外比表面积和介孔孔容.     

不同分子筛上1-己烯骨架异构化反应性能的研究

以HZSM-35、HZSM-5、HM和Hβ四种分子筛为1-己烯骨架异构化催化剂,比较研究了四种催化剂的异构化性能,对其构效关系进行了关联。结果表明,相比于HZSM-5和Hβ分子筛,HZSM-35和HM具有适宜的酸量,有效孔径为0.4-0.6 nm,而且无晶穴、无交叉孔道,具有良好的择形催化效应,在转化率高达95%的同时,C_5-和C₇₊等副产物的收率在20%左右,异己烯收率可达40%-50%。进一步对四种分子筛进行酸碱改性处理,结果显示,虽然酸性质略有改变,但是一维孔结构的HZSM-35和HM分子筛的异构化性能仍明显优于多维孔结构的HZSM-5和Hβ分子筛,说明在酸性质一定的前提下,孔结构对异构化反应起关键作用。     

Fe-Zn-Zr/分子筛复合催化剂上CO2加氢合成异构烷烃Ⅰ.不同分子筛对催化剂性能的影响

 在Fe-Zn-Zr/分子筛复合催化剂上考察了不同类型的分子筛对CO2加氢反应性能的影响. 结果表明,不同分子筛对复合催化剂性能的影响不同,Fe-Zn-Zr/HY是合成异构烷烃有效的复合催化剂. 分子筛的酸性及酸强度对复合催化剂性能有较大的影响,中等强度和较高强度的酸性位有利于异构烃的生成.     

Adsorption, diffusion and catalysis of mesostructured zeolite HZSM-5

Adsorption and diffusion properties of n-octane in meso-structured HZSM-5 zeolites were studied by high precision intelligent gravimetric analysis (IGA) and ZLC technology between 293?K and 393?K. As expected, great increase in adsorption capacity and diffusion efficient of n-octane in the mesostructured HZSM-5 zeolites was observed compared with conventional HZSM-5. At the same time, the adsorption activation energy of n-octane in the mesostructured HZSM-5 zeolites was significantly decreased. The adsorption heats with low n-octane loading showed a clear decline with increase of mesoporosity in the zeolite samples. These results clearly indicate that introduction of mesopores into the zeolites offered a short diffusion path and high diffusion rate for reactants and products, which resulted in a high yield of fuel oil and an enhanced resistance against the catalyst deactivation in the reaction of methanol to gasoline.     

晶粒大小对ZSM-5分子筛甲醇制低碳烯烃催化性能的影响

对三种HZSM-5分子筛进行Ca改性,获得两组酸性接近的催化剂,考察了晶粒大小对甲醇制低碳烯烃(MTO)反应的影响。通过进一步与Na改性的比较,探讨了Ca在催化反应中的作用。采用扫描电镜(SEM)测定晶粒大小及形貌,氨气程序升温脱附(NH3-TPD)及吡啶红外吸附(Py-IR)表征催化剂的酸性。MTO催化性能测定结果表明,HZSM-5的低碳烯烃选择性较低且下降较快,催化活性降低也快;Ca改性降低酸性,提高了低碳烯烃选择性和催化稳定性;晶粒大小主要影响催化稳定性,小晶粒分子筛催化剂稳定性更好。高Ca含量改性效果更好;钠改性也提高了低碳烯烃选择性,但其稳定性较差。对于HZSM-5和Ca/HZSM-5,小晶粒的催化剂具有较好的催化稳定性。提出Ca参与了催化反应,MTO是一个酸碱协同作用的催化过程。     

氟改性对纳米 HZSM-5 分子筛催化甲醇制丙烯的影响

 在比较了纳米和微米 HZSM-5 分子筛催化甲醇制丙烯反应性能的基础上, 对纳米 HZSM-5 分子筛进行了氟改性. 利用透射电镜、N2 吸附、X 射线衍射、氨程序升温脱附和吡啶吸附-红外光谱技术对改性前后的样品进行了表征, 并在常压、500 oC 和甲醇空速 (WHSV) 为 1.0 h–1 的反应条件下, 在连续流动固定床微型反应器上考察了其催化甲醇制丙烯的性能. 结果表明, 当氟含量<10% 时, 随氟含量的增加, 改性纳米 HZSM-5 分子筛的酸量减少, 酸强度降低, 从而使丙烯选择性和催化剂稳定性不断提高. 但过量 (15%) 氟的改性使纳米 HZSM-5 分子筛的酸量、比表面积和孔容均明显减小, 致使其稳定性反而降低. 在适量 (10%) 氟改性的纳米 HZSM-5 分子筛上, 丙烯选择性和维持甲醇完全转化的反应时间分别由原来的 30.1% 和 75 h 增加到 46.7% 和 145 h.     

不同硅铝比两亲性HZSM-5沸石的制备和表征

 采用三甲基氯硅烷并通过控制水的添加量对硅铝比分别为25, 42和101的HZSM-5沸石进行外表面修饰,制得三种两亲性沸石样品. 水的添加量对沸石催化剂的两亲性有显著影响. 红外光谱和低温氮吸附等测试结果表明,两亲性沸石样品具有与各自母体沸石相似的酸性及略小的比表面积. 在环己烯水合及乙酸异戊酯水解的相界面反应中,两亲性沸石分布于水-油两相界面,并表现出明显高于各自母体沸石的催化活性. 硅铝比为42的两亲性HZSM-5样品表现出最佳的相界面催化性能. 相对于环己烯水合反应,两亲性HZSM-5沸石更适用于乙酸异戊酯水解的相界面催化反应.     

分子筛骨架结构和酸性对其甲醇制烯烃(MTO)催化性能影响研究进展

甲醇制烯烃(MTO)作为一条由煤、天然气及生物质等含碳资源制备重要化学品的非石油路线,近年来备受人们关注。分子筛作为MTO的催化剂,其催化性能和MTO反应行为与其骨架结构和酸性特征密切相关,而认识这些关系对研发新型高效MTO催化剂和改进反应工艺具有重要意义。为此,研究简述了近年来有关甲醇转化制烯烃过程中分子筛催化活性及反应机理的理论和实验研究进展。重点讨论了不同分子筛在MTO过程中烃池物种、反应路线以及催化动力学方面的差异,分析了分子筛催化剂的骨架结构及酸性对其MTO催化性能的影响。     

Selective Conversion of Glycerol to Methanol over CaO-Modified HZSM-5 Zeolite

Biodiesel is generally produced from vegetable oils and methanol, which also generates glycerol as byproduct. To improve the overall economic performance of the process, the selective formation of methanol from glycerol is important in biodiesel production. In the present study, a CaO modified HZSM-5 zeolite was prepared by an impregnation method and used for the conversion of glycerol to methanol. We found that the 10%CaO/HZSM-5 with Si/Al ratio of 38 exhibited highest selectivity to methanol of 70%, with a glycerol conversion of 100% under 340 ℃ and atmospheric pressure. The characterization results showed that the introduction of a small amount of CaO into the HZSM-5 did not affect the structure of zeolite. The incorporation of HZSM-5 as an acidic catalyst and CaO as a basic catalyst in a synergistic catalysis system led to higher conversion of glycerol and selectivity of methanol.     

Catalytic performance of imidazole modified HZSM-5 for methanol to aromatics reaction

A facile approach was developed for the preparation of nano-sized HZSM-5 with a hierarchical mesoporous structure by adding imidazole into conventional zeolite synthesis precursor solution. The physicochemical properties of modified HZSM-5 were characterized by X-ray diffraction(XRD), N_2 adsorption–desorption isotherms, scanning electron microscopy(SEM), NH_3-temperature-programmed desorption(NH_3-TPD) and pyridine adsorption infrared spectroscopy(Py-IR). The coke in spent catalysts was characterized by thermogravimetry(TG). The results showed that hierarchical HZSM-5 zeolites with excellent textural properties, such as abundant porous structure, uniform particle size and suitable acidity, could be synthesized by the recipe of one-pot synthesis routes. Moreover, the obtained HZSM-5 exhibited higher selectivity of total aromatics as well as longer lifetime in the catalytic conversion of methanol to aromatics, comparing with conventional HZSM-5. It is expected that the synthesis approach demonstrated here will be applicable to other zeolites with particular textural properties and controllable particle sizes, facilitating the emergence of new-type porous materials and their related applications in catalysis and separation.     

Properties and Characterization of Modified HZSM—5 Zeolites

Physicochemical and catalytic properties of phosphorus and boron modified HZSM-5 zeolites treated with 100% steam at 673K were investigated.The acidity and distribution of acidic sites were studied by infrared spectroscopy using pyridine as probe molecule and temperature programmed desortion (TPD) of ammonia.The structure of the samples was characterized by XRD,and the textural properties of the catalysts were determined by nitrogen isothermal adsorption-desorption measurements and scanning electron microscopy(SEM).The XRD results show that the modified samples have no novel crystalline phase,indicating a high dispersion of phosphorus and boron species.After treatment,the microporous volume and surface area of the samples markedly decrease,implying the bolockage of the channel.The nitrogen adsorption-desorption measurements suggest that the isothermal type of all samples is a combination of isothermal type Ⅰ and Ⅳ，and all hysteresis loops resemble the H4-type in the IUPAC classification.The total acidity of the modified samples,determined by pyrldine adsorption IR and TPD of ammonia,decreases in contrast to that of the parent HZSM-5.The conversion of n-heptane over P and B steammodified HZSM-5 is higher than that of P and B-modified HZSM-5 zeolites but lower than that of the parent HZSM-5.     

Effect of the Si/Al ratio of HZSM-5 zeolite on the production of dimethyl ether before and after ultrasonication

A series of as-synthesized HZSM-5 zeolites with different Si/Al ratios (25, 90, 120, 240 and 400) were post-treated by ultrasonication for an optimum time of 60 min. The morphology, acidity and textural properties of HZSM-5 were characterized with XRD, SEM, N₂ adsorption and NH₃-TPD techniques. The catalytic performance was evaluated by dehydration of methanol to dimethyl ether (DME), which is a promising gaseous automotive fuel in future. It was found that the Si/Al ratio of HZSM-5 had considerable impacts on its catalytic performance for dehydration of methanol to DME. Its activity increased with decreasing Si/Al ratio from 400 to 25. Ultrasonication of HZSM-5 could significantly improve its catalytic performance.     

热处理对HZSM-5结构、酸性及催化乙醇脱水反应性能的影响

对商用HZSM-5分子筛进行高温热处理,利用X射线衍射(XRD)、核磁共振波谱法(²⁷Al-MAS NMR)低温氮吸附、电感耦和等离子体放射光谱(ICP-AES)、氨-程序升温脱附(NH₃-TPD)和吡啶吸附傅里叶变换红外(FT-IR)光谱等技术对高温热处理改性前后样品进行了表征,并考察了高温热处理对分子筛的结构、酸性及催化乙醇脱水制乙烯反应性能的影响。结果表明,热处理改性后的HZSM-5分子筛发生骨架脱铝,B酸减少,L酸增多,孔容增大,出现新的介孔;适中的酸性位和复合型的介-微双孔道结构使其减少了反应中的副反应,乙烯的选择性得到提高,催化剂寿命显著提高。     

Nitrous Oxide Adsorption and Decomposition on Zeolites and Zeolite-like Materials

Decomposition of N₂O on modified zeolites, crystalline titanosilicalites, and related amorphous systems is studied by the catalytic and spectroscopic methods. Zinc-containing HZSM-5 zeolites and titanosilicalites with moderate Ti/Si ratios are shown to exhibit a better catalytic performance in N₂O decomposition as compared with conventionally used Cu/HZSM-5 zeolites and amorphous Cu-containing catalysts. Dehydroxylation of the HZSM-5 zeolite by calcination at 1120 K results in an enhancement of the N₂O conversion. The mechanism of the reaction and the role of coordinatively unsaturated cations and Lewis acid sites in N₂O decomposition are discussed on the basis of the spectroscopic data.     

HZSM-5分子筛上C_(6～8)混合链烃和邻二甲苯的加氢裂化

在连续流动固定床装置上,探讨了不同酸性HZSM-5上C6~8混合链烃(以下简称混合烃)和邻二甲苯加氢裂化的变化规律,并在稳定条件下考察了反应温度、质量空速以及氢烃体积比等反应参数的影响。混合烃的加氢裂化伴随着芳构化反应,酸性较弱的HZSM-5主要发生加氢裂化反应,裂化产物以正构烷烃为主,甲烷和异构烷烃较少。酸性强的HZSM-5上,起初以芳构化反应为主,稳定之后产物分布与弱酸催化剂接近。混合烃的加氢裂化反应表现出明显的温度效应,而质量空速和氢烃体积比的影响较小。在380℃、3.0 MPa、质量空速1.02 h-1、氢烃体积比1 000的条件下,100 h内混合烃的转化率均在99%以上,稳定的裂化反应选择性在95%以上。邻二甲苯发生加氢裂化及异构、歧化反应,酸性强的HZSM-5裂化产物收率高,裂化产物分布与混合烃的基本相同。稳定的邻二甲苯裂化反应选择性小于10%。     

Synthesis of jet fuel through the oligomerization of butenes on zeolite catalysts

In this study, the oligomerization of a butene mixture composed of 1-butene, cis-2-butene and trans-2-butene over several types of zeolites in a fixed-bed catalytic reactor at an elevated pressure was studied to produce hydrocarbons in the jet fuel range (C₈–C₁₆). Three types of zeolites, HZSM-5, Hβ and HY, were compared to evaluate the performance during the synthesis of jet fuel via the oligomerization of the aforementioned butene mixture. Compared to HY and Hβ, HZSM-5 showed a very stable butene conversion rate with high selectivity to jet-fuel-range hydrocarbon, which could be attributed to high resistance to coke resulting from the pore structure. HZSM-5 (50) shows the best quantitative conversion performance and yield for jet fuel for a time-on-stream of up to 6 h. It was also noted that the branched-to-linear hydrocarbon ratio reached 8.7 over the HZSM-5 (50) catalyst, which is beneficial to improve the cold properties of jet fuel. The present study reveals that HZSM-5 (50) is a potential catalyst for jet fuel synthesis through the oligomerization of butene mixture, exhibiting high stability and a high yield.     

EFFECT OF SULFURIZATION ON THE PIIYSICAL ANDCATALYTIC PROPERTIES OF HZSM-5 ZEOLITES

IntroductionZSM-5zeoliteshavebeenwidelyemployedinthefieldofhydrocarbonconversion.UtiliZationofMo-containingandKorBamodifiedZSM-5zeolitestOactivatemethaneandtOpreparelightolefinsfromparaffinshavebeenreportedinourpreviouspapersll'2].However,littleattentionh…     

Effects of Calcination Temperature on the Acidity and Catalytic Performances of HZSM-5 Zeolite Catalysts for the Catalytic Cracking of n-Butane

The acidic modulations of a series of HZSM-5 catalysts were successfully made by calcination at different treatment temperatures, i.e. 500, 600, 650, 700 and 800 ℃, respectively. The results indicated that the total acid amounts, their density and the amount of B-type acid of HZSM-5 catalysts rapidly decreased, while the amounts of L-type acid had almost no change and thus the ratio of L/B was obviously enhanced with the increase of calcination temperature (excluding 800 ℃). The catalytic performances of modified HZSM-5 catalysts for the cracking of n-butane were also investigated. The main properties of these catalysts were characterized by means of XRD, N2 adsorption at low temperature, NH3-TPD, FTIR of pyridine adsorption and BET surface area measurements. The results showed that HZSM-5 zeolite pretreated at 800 ℃ had very low catalytic activity for n-butane cracking. In the calcination temperature range of 500-700 ℃, the total selectivity to olefins, propylene and butene were increased with the increase of calcination temperature, while, the selectivity for arene decreased with the calcination temperature.The HZSM-5 zeolite calcined at 700 ℃ produced light olefins with high yield, at the reaction temperature of 650 ℃ the yields of total olefins and ethylene were 52.8% and 29.4%, respectively. Besides, the more important role is that high calcination temperature treatment improved the duration stability of HZSM-5zeolites. The effect of calcination temperature on the physico-chemical properties and catalytic performance of HZSM-5 for cracking of n-butane was explored. It was found that the calcination temperature had large effects on the surface area, crystallinity and acid properties of HZSM-5 catalyst, which further affected the catalytic performance for n-butane cracking.     

Bimetallic Lanthanum-Cerium-Loaded HZSM-5 Composite for Catalytic Deoxygenation of Microalgae-Hydrolyzed Oil into Green Hydrocarbon Fuels

Due to their high lipid content, microalgae are one of the most significant sources of green hydrocarbons, which might help lessen the world’s need for fossil fuels. Many zeolite-based catalysts are quickly deactivated by coke production and have a short lifetime. In this study, a bimetallic Lanthanum-Cerium (La-Ce)-modified HZSM-5 zeolite catalyst was synthesized through an impregnation method and was tested for the conversion of hydrolyzed oil into oxygen-free hydrocarbon fuels of high energy content. Initially, hydrolyzed oil (HO), the byproduct of the transesterification process, was obtained by the reaction of crude oil derived from Chlorella vulgaris microalgae and a methanol. Various catalysts were produced, screened, and evaluated for their ability to convert algal HO into hydrocarbons and other valuable compounds in a batch reactor. The performance of HZSM-5 was systematically tested in view of La-Ce loaded on conversion, yield, and selectivity. NH₃-TPD analysis showed that the total acidity of the La-Ce-modified zeolites was lower than that of the pure HZSM-5 catalyst. TGA testing revealed that including the rare earth elements La and Ce in the HZSM-5 catalyst lowered the catalyst propensity for producing coke deposits. The acid sites necessary for algal HO conversion were improved by putting La and Ce into HZSM-5 zeolite at various loading percentages. The maximum hydrocarbon yield (42.963%), the highest HHV (34.362 MJ/Kg), and the highest DOD% (62.191%) were all achieved by the (7.5%La-2.5%Ce)/HZSM-5 catalyst, which was synthesized in this work. For comparison, the hydrocarbon yield for the parent HZSM-5 was 21.838%, the HHV was (33.230 MJ/Kg), and the DOD% was 44.235%. In conclusion, La and Ce-loading on the parent HZSM-5 may be responsible for the observed alterations in textural properties; nevertheless, there is no clear correlation between the physical features and the hydrocarbon yield (%). The principal effect of La and Ce modifying the parent HZSM-5 zeolite was to modify the acidic sites needed to enhance the conversion (%) of the algal HO during the catalytic deoxygenation process, which in turn raised the hydrocarbon yield (%) and increased the HHV and DOD%.     

Effect of external surface of HZSM-5 zeolite on product distribution in the conversion of methanol to hydrocarbons

The external surface of HZSM-5 zeolite was passivated by liquid siliceous deposition and by acidic sites poisoning with lepidine, respectively. Then methanol-to-hydrocarbons （MTH） reaction was investigated over the above as-prepared catalysts and the dissoluble coke on these used catalysts was analyzed by GC-MS, to study the role of the external surface of HZSM-5 in the catalytic reaction. Comparison with the experi- mental results based on parent ZSM-5 showed that the product distribution of MTH reaction was obviously influenced by the external surface. Evidences were listed as follows： （1） the final product on parent HZSM-5 showed higher aromatic selectivity, lower olefin selectivity, lower ra- tio of C2/C3＋ aliphatics and higher ratio of C3/C4＋ aliphatics than the reaction mixture produced by the sole catalysis of acidic sites in HZSM-5 channel; （2） a little of pentamethylbenzene and hexamethylbenzene in the product on parent HZSM-5, was produced via multi-methylation of methylbenzene on the external surface. The above conclusion may also be suitable for MTH reaction over other zeolites with 10-ring channel.