Suppression of Low-frequency Variations in Vortex Shedding by a Splitter Plate Behind a Bluff Body

Measurements of instantaneous pressure fluctuations on a trapezoidal cross-section cylinder indicate that the low-frequency variations embedded in the vortex-shedding process can be successfully suppressed by insertion of a splitter plate whose length is twice the maximum width of the trapezoidal cylinder. The experiments were performed at Reynolds numbers in a range of 5 × 10³ to 4·5 × 10⁴. Spanwise correlation of the pressure fluctuations measured on the cylinder further indicates that the suppression of low-frequency variations improves the degree of two-dimensionality of vortex shedding. These findings are attributed to the presence of the splitter plate having an effect on stabilizing the vortex formation length which is comparable to the length of the splitter plate, thus eliminating the low-frequency variations embedded in the base pressure.     

Low-frequency fluctuations in the near-wake region of a trapezoidal cylinder with low aspect ratio

Base pressure signals obtained on a trapezoidal cylinder with an aspect ratio 4.7, at Reynolds numbers of the order of 10⁴, were examined after being low-pass filtered at different cut-off frequencies. For the range of the Reynolds numbers studied, the integral time scales of the low-passed fluctuations versus the cut-off frequencies chosen was found to fall on a curve. Cross-correlation between the pressure fluctuations measured at the cylinder base and the velocity fluctuations detected in the near-wake region were examined with the signal traces low-passed at different cut-off frequencies. Accordingly, an optimal cut-off frequency was defined as the one corresponding to the highest correlation obtained. The integral time scale of the low-passed fluctuations in reference to the optimal cut-off frequency was found to be about two times the vortex-shedding period. The low-frequency variations measured appeared to be insensitive to the artificial tripping to the sidewall boundary layer, and exhibited a global behavior in a near-wake region.     

Features of the turbulent flow around symmetric elongated bluff bodies

The flow fields around three elongated bluff bodies with the same chord-to-thickness ratios but distinct leading and trailing edge details were measured at a Reynolds number of 3×10⁴. These models each represent a case where: leading edge shedding dominates, trailing edge shedding dominates and a case where there is a balance between the two. The results show that the vortex street parameters vary between the models, and in particular, the shedding frequencies are significantly altered by the geometry. However, contrary to the current understanding for shorter bluff bodies, the scale of the recirculation region is found to be similar for each model, even though the shedding frequency changes within the range from 0.15 to 0.24. Also, the base pressure does not follow trends with shedding frequency expected from shorter bluff bodies. A force balance of the recirculation region shows that the near wake of each body is significantly affected by the Reynolds shear stress distribution and the resultant force due to the pressure field in the mean recirculation region. These differences infer that the distinct vortex formation characteristics depend on the state of the trailing edge shear layers. The boundary layers at the trailing edge have been quantified, as have the leading edge separation bubbles, and the marked differences in the wake details are shown to depend on the leading edge separation.     

Spanwise correlations in the wake of a circular cylinder and a trapezoid placed inside a circular pipe

The spanwise correlation of a circular cylinder and a trapezoidal bluff body placed inside a circular pipe in fully developed turbulent regime is studied using hotwire anemometer. The present configuration possesses complex fluid structure interaction owing to the following features: high blockage effect; low aspect ratio of the body; upstream turbulence and interaction of axisymmetric flow with a two dimensional bluff body. The spatial correlation of such configuration is seldom reported in the literature. Results are presented for Reynolds number of Re_D=1×10⁵. Three different blockage ratios (0.14, 0.19 and 0.28) are considered in the present study. Correlation coefficient is observed to improve with increase in blockage ratio. Compared to a circular cylinder, a trapezoidal bluff body possesses high correlation length. The near wall effects tend to increase the phase drift, which is reflected in low correlation coefficients close to the pipe wall. The results show that the simultaneous effect of curvature, low aspect ratio and upstream turbulence reduces the correlation coefficients significantly as compared to unconfined and confined (parallel channel) flows. The low frequency modulations with a circular cylinder are higher for lower blockage ratios. The three-dimensionality of vortex shedding for trapezoid with a blockage ratio of 0.28 was observed to be lower compared to circular cylinder and all other blockage ratios. Low frequency modulations were found to be responsible for weak vortex shedding from a circular cylinder compared to a trapezoidal bluff body. The vortex shedding is observed to be nearly two dimensional in case of a trapezoidal bluff body of blockage ratio 0.28.     

Experimental study on the wake behind tapered circular cylinders

The flow around tapered cylinders can act as basic models for numerous bluff body flows with a spanwise variation of either the body shape or the inflow conditions. The well-known vortex street is influenced by strong three-dimensional effects from the spanwise variation of the shedding frequency, namely oblique vortex shedding and vortex dislocations. Stereo-PIV was chosen to study these phenomena, since it allows analyzing planes with the full three-component, instantaneous velocity fields and local, time-dependent variations in the same setting. Hence, detailed aspects of the vortex dislocation phenomenon are presented. Single vortex dislocation events are presented through the local variation of the three measured velocity components u, v and w. Longer time-series reveal both period and location of these dislocation events, as well as quantity and sizes of the cells of constant shedding velocity in between them. The influence of the Reynolds number and the cylinder aspect ratio on the vortex cells could be shown. The analysis of the vortex shedding behavior shows good agreement with previously published results. At the same time, the applied PIV technique provides more spatial information than point-based measurements and offers insight into a Reynolds number range that is currently out of reach of Direct Numerical Simulations.     

钝体尾流控制机理及方法研究进展

首先从涡脱落生成理论出发对钝体尾流控制方法进行了分类,并简单介绍了国内尾流控制研究情况. 之后介绍了我们用窄条或小方柱取代小圆柱后,对Strykowsky和Sreenivasan 控制方法的改进及其在高雷诺数下对圆柱和方柱尾流涡脱落的有效抑制情况, 并探讨了控制件钝度对抑制效果的影响.第3部分用实验数据对各个涡脱落生成模型做了分析与检验, 指出控制件方法的机理与改变钝体分离位置、减小钝体背压吸力、改变流动的展向相关性、 防止钝体两侧剪切层相互作用等无关,而与钝体近尾流速度剖面的局部修正及其稳定性的改变有关. 最后简单介绍了控制件方法今后研究工作展望及其工程应用前景.     

Effects of the corner radius on the near wake of a square prism

The near wake of square cylinders with different corner radii was experimentally studied based on particle imaging velocimetry (PIV), laser doppler anemometry (LDA) and hotwire measurements. Four bluff bodies, i.e., r/d=0 (square cylinder), 0.157, 0.236, 0.5 (circular cylinder), where r is corner radius and d is the characteristic dimension of the bluff bodies, were examined. A conditional sampling technique was developed to obtain the phase-averaged PIV data in order to characterize quantitatively the effect of corner radii on the near-wake flow structure. The results show that, as r/d increases from 0 to 0.5, the maximum strength of shed vortices attenuates, the circulation associated with the vortices decreases progressively by 50%, the Strouhal number, St, increases by about 60%, the convection velocity of the vortices increases along with the widening of the wake width by about 25%, the vortex formation length and the wake closure length almost double in size. Meanwhile, both the vortex wavelength, λ _x , and the lateral spacing, λ _y , decrease as r/d increases, but the ratio of λ _y to λ _x is approximately 0.29, irrespective of r/d, which is close to the theoretical value of 0.281 for a stable Karman vortex street. The decrease in wavelength is probably responsible for the change in the flow structure from the approximately circular-shaped vortex at r/d=0 to the laterally stretched vortex at r/d=0.5. The leading edge corner radius is more important than the trailing one in influencing the near wake structure since it determines to a great extent the behavior of the streamlines, the separation angle and the base pressure. It is further found that the ratio of the mean drag coefficient to the total shed circulation, C _d/Γ₀, approaches a constant, about 0.25 for different bluff bodies in the subcritical flow regime. The streamwise evolution of vortices and the streamwise fluctuating velocity along the centerline for rounded cylinders are also discussed.     

圆柱绕流的电磁控制

流体绕过非流线物体时，在物体尾部形成涡街，使其表面周期性变化的阻力和升力增加，从而导致物体振荡，产生噪音。本文通过实验和计算，研究圆柱绕流的电磁控制，阐述浸于弱电介质溶液中，表面包覆电磁激活板的圆柱，在电磁力作用下的流体控制原理，讨论电磁力的消涡、减阻和减振过程。     

Effect of velocity ratio on the streamwise vortex structures in the wake of a stack

The time-averaged velocity and streamwise vorticity fields within the wake of a stack were investigated in a low-speed wind tunnel using a seven-hole pressure probe. The experiments were conducted at a Reynolds number, based on the stack external diameter, of Re_D=2.3×10⁴. The stack, of aspect ratio AR=9, was mounted normal to a ground plane and was partially immersed in a flat-plate turbulent boundary layer, where the ratio of the boundary layer thickness to the stack height was δ/H≈0.5. The jet-to-cross-flow velocity ratio was varied from R=0 to 3, which covered the downwash, crosswind-dominated and jet-dominated flow regimes. In the downwash and crosswind-dominated flow regimes, two pairs of counter-rotating streamwise vortex structures were identified within the stack wake. The tip vortex pair located close to the free end of the stack, and the base vortex pair located close to the ground plane within the flat-plate boundary layer, were similar to those found in the wake of a finite circular cylinder, and were associated with the upwash and downwash flow fields within the stack wake, respectively. In the jet-dominated flow regime, a third pair of streamwise vortex structures was observed, referred to as the jet-wake vortex pair, which occurred within the jet-wake region above the free end of the stack. The jet-wake vortex pair had the same orientation as the base vortex pair and was associated with the jet rise. The peak vorticity and strength of the streamwise vortex structures were functions of the jet-to-cross-flow velocity ratio. For the tip vortex structures, their peak vorticity and strength reduced as the jet-to-cross-flow velocity ratio increased.     

Flow regimes and frequency selection of a cylinder oscillating in an upstream cylinder wake

This paper describes flow around a pair of cylinders in tandem arrangement with a downstream cylinder being fixed or forced to oscillate transversely. A sinusoidal parietal velocity is applied to simulate cylinder oscillation. Time-dependent Navier-Stokes equations are solved using finite element method. It is shown that there exist two distinct flow regimes: ‘vortex suppression regime’ and ‘vortex formation regime’. Averaged vortex lengths between the two cylinders, pressure variations at back and front stagnant points as well as circumferential pressure profiles of the downstream cylinder are found completely different in the two regimes and, thus, can be used to identify the flow regimes. It is shown that frequency selection in the wake of the oscillating cylinder is a result of non-linear interaction among vortex wakes upstream and downstream of the second cylinder and its forced oscillation. Increasing cylinder spacing results in a stronger oscillatory incident flow upstream of the second cylinder and, thus, a smaller synchronization zone.     

Near wake properties of axisymmetric bluff body flows

Experiments have been made to measure some of the near wake properties of axisymmetric bluff body flows with fixed points of separation, including the detention or residence time of fluid borne scalar entities, base pressure coefficient, wake bubble length parameter and shape parameter. Measurements were made in smooth and turbulent air flow for Reynolds number in the range 2×10³<Re<4×10⁴. The results for a given bluff body were found to be uniquely controlled by a free-stream turbulence parameter. The data for all the shapes of bluff body in the class under consideration were found to collapse into unique inter-relationships by the introduction of the face pressure coefficient as a quantitative measure of “bluffness”. This paper was originally presented at the 14th International Congress of Theoretical and Applied Mechanics, Delft (August–September, 1976).     

Flow structure around two finite circular cylinders located in an atmospheric boundary layer: side-by-side arrangement

The flow structure around the free-end region of two adjacent finite circular cylinders embedded in an atmospheric boundary layer (ABL) was investigated experimentally. The experiments were carried out in a closed-return-type subsonic wind tunnel, in which two finite cylinders with an aspect ratio of 6 were mounted vertically on a flat plate in a side-by-side arrangement. The Reynolds number based on the cylinder diameter was about Re=2×10⁴. Systems with gap ratios (i.e., center-to-center distance/cylinder diameter) in the range 1.0–2.0 were investigated. A hot-wire anemometer was employed to measure the wake velocity, and the mean pressure distribution on the cylinder surface was also measured. The flow past two finite cylinders was found to have a complicated three-dimensional wake structure in the region near the free ends. As the gap ratio increases, regular vortex-shedding becomes dominant, but the length of the vortex formation region decreases. The pressure distribution and flow structure around two cylinders were found to differ substantially from the behavior of a two-dimensional circular cylinder due to mutual interference. The three-dimensional flow structure seems to originate from the strong entrainment of irrotational fluids caused by the downwash counter-rotating vortices separated from the finite cylinder (FC) free ends.     

Control of vortex shedding by thermal effect at low Reynolds numbers

An experimental study has been made of the control of vortex shedding in the wake of two two-dimensional bluff bodies, a circular cylinder and a flat ribbon. The study has shown that this control, easily realized by heating the bluff body, depends on the nature of the fluid. In the absence of buoyancy effects, related to the temperature dependence of the dynamic viscosity, the heating is found to stabilize the wake in air while the opposite result is obtained in water. Detailed measurements of the velocity fields in air, in isothermal and in heated body, show that this control is linked to slight modifications of the flow in the near wake and can be taken into account by the effective Reynolds number approach. The measurements also show that the degree of instability can be related to the level of interaction between the two initial shear layers at the end of the recirculation zone.     

Non-linear Response of Turbulent Premixed Flames to Imposed Inlet Velocity Oscillations of Two Frequencies

This paper describes an experimental study investigating the non-linear response of lean premixed air/ethylene flames to strong inlet velocity perturbations of two frequencies. The combustor has a centrally-placed bluff body and a short quartz section. The annulus between the bluff body and the flow tube, which also housed the acoustic pressure transducers, allowed the reactants into the combustor. The inlet flow was perturbed using loudspeakers. High speed laser tomography, OH* chemiluminescence and OH Planar Laser Induced Fluorescence (PLIF) have been used for flow visualization, heat release and flame surface density (FSD) measurements respectively. The heat release fluctuations increased initially linearly with inlet velocity amplitude for a single frequency forcing, with saturation occurring after forcing amplitudes of around 15% of the bulk velocity, which was found to occur due to vortex roll up and subsequent flame annihilation. The introduction of energy at the second frequency (i.e, the harmonic) was found to change the vortex formation and shedding frequency, depending on the level of forcing. This resulted in a non-linear flame response transfer function (defined as the amplitude of unsteady heat release divided by the amplitude of velocity perturbation at the fundamental) whose amplitude depended greatly on the amount of harmonic content present in the perturbations. The introduction of higher harmonics reduced the flame annihilation events, which are responsible for saturation, thus reducing non-linearity in the amplitude dependence of the flame response. These results were further verified using sequential time-resolved OH PLIF measurements. The findings from this study suggest that the acoustic response of the flame was mostly due to flame area variation effected by modulation of the annular jet and evolution of the shear layers.     

Control of mean and fluctuating forces on a circular cylinder at high Reynolds numbers

A narrow strip is used to control mean and fluctuating forces on a circular cylinder at Reynolds numbers from 2.0 × 10⁴ to 1.0 × 10⁵. The axes of the strip and cylinder are parallel. The control parameters are strip width ratio and strip position characterized by angle of attack and distance from the cylinder. Wind tunnel tests show that the vortex shedding from both sides of the cylinder can be suppressed, and mean drag and fluctuating lift on the cylinder can be reduced if the strip is installed in an effective zone downstream of the cylinder. A phenomenon of mono-side vortex shedding is found. The strip-induced local changes of velocity profiles in the near wake of the cylinder are measured, and the relation between base suction and peak value in the power spectrum of fluctuating lift is studied. The control mechanism is then discussed from different points of view. The project supported by the National Natural Science Foundation of China (10172087 and 10472124). The English text was polished by Yunming Chen.     

TR-PIV measurement of the wake behind a grooved cylinder at low Reynolds number

A comparative study of the wakes behind cylinders with grooved and smooth surfaces was performed with a view to understand the wake characteristics associated with the adult Saguaro cacti. A low-speed recirculation water channel was established for the experiment; the Reynolds number, based on the free-stream velocity and cylinder diameter (D), was kept at Re_D=1500. State-of-the-art time-resolved particle image velocimetry (TR-PIV) was employed to measure a total of 20 480 realizations of the wake field at a frame rate of 250 Hz, enabling a comprehensive view of the time- and phase-averaged wake pattern. In comparison to the wake behind the smooth cylinder, the length of the recirculation zone behind the grooved cylinder was extended by nearly 18.2%, yet the longitudinal velocity fluctuation intensity was considerably weakened. A global view of the peaked spectrum of the longitudinal velocity component revealed that the intermediate region for the grooved cylinder, which approximately corresponds to the transition region where the shear layer vortices interact, merge and shed before the formation of the Karman-like vortex street, was much wider than that for the smooth one. The unsteady events near St=0.3-0.4 were detected in the intermediate region behind the grooved cylinder, but no such events were found in the smooth cylinder system. Although the formation of the Karman-like vortex street was delayed by about 0.6D downstream for the grooved cylinder, no prominent difference in the vortex street region was found in the far wake for both cylinders. The Proper Orthogonal Decomposition (POD) method was used extensively to decompose the vector and swirling strength fields, which gave a close-up view of the vortices in the near wake. The first two POD modes of the swirling strength clarified the spatio-temporal characteristics of the shear layer vortices behind the grooved cylinder. The small-scale vortices superimposed on the shear layers behind the grooved cylinder were found to be generated and convected downstream in the same phase, which would significantly reduce the fluctuating force on the cylinder surface.     

A bypass wake induced laminar/turbulent transition

The process of laminar to turbulent transition induced by a von Karman vortex street wake, was studied for the case of a flat plate boundary layer. The boundary layer developed under zero pressure gradient conditions. The vortex street was generated by a cylinder positioned in the free stream. An X-type hot-wire probe located in the boundary layer, measured the streamwise and normal to the wall velocity components. The measurements covered two areas; the region of transition onset and development and the region where the wake and the boundary layer merged producing a turbulent flow. The evolution of Reynolds stresses and rms-values of velocity fluctuations along the transition region are presented and discussed. From the profiles of the Reynolds stress and the mean velocity profile, a ‘negative' energy production region along the transition region, was identified. A quadrant splitting analysis was applied to the instantaneous Reynolds stress signals. The contributions of the elementary coherent structures to the total Reynolds stress were evaluated, for several x-positions of the near wall region. Distinct regions in the streamwise and normal to the wall directions were identified during the transition.     

外部激励Stuart-Landau模型的数值研究

将非线性常微分方程组周期解的求解看作一个边值问题 ,运用Newton迭代构造求解这组方程的数值方法。利用上述方法求得了激励Stuart Landau方程的周期解 ,研究了圆柱振动对圆柱后Karman涡街的抑制现象 ,和振动的频率锁定现象 ,证明了激励Stuart Landau方程描写钝体尾迹动力系统的有效性     

An Embedding Method for Bluff Body Flows: Interactions of Two Side-by-Side Cylinder Wakes

We introduce a simple method for the numerical simulation of bluff body flows where the solid object is represented by a distributed body force in the Navier–Stokes equations. The body force density is found at every time step to reduce the velocity within the computational cells occupied by the rigid body to a prescribed value. The method combines certain ideas from the immersed boundary method which was developed to treat biofluid mechanical flows and the volume-of-fluid method for simulating flows with fluid–fluid interfaces. The main advantage of this embedding method is that the computations can be effected on a regular Cartesian grid, without the need to fit the grid to the bluff body surfaces. Thus, flow past several complex bodies can be treated as easily as flow past a single body. The method is validated by reproducing well-established results for vortex shedding from a stationary cylinder. The flow past two side-by-side cylinders is then investigated. When the distance between the cylinders is small, they are seen to shed vortices in-phase, whereas for larger distances, the shedding occurs in anti-phase. For intermediate distances, various shedding patterns are observed, including quasi-periodic, asymmetric and chaotic regimes. Mean values and phase portraits associated with the cylinder lift and drag coefficients, as well as spectral analysis of the same data, are used to describe the flow. A transition diagram that can be compared with experiments or models outlines the various dynamical regimes as a function of the distance between the cylinders and the Reynolds number.