Surface structure of thin asymmetric PS-b-PMMA diblock copolymers investigated by atomic force microscopy

Asymmetric poly(styrene-b-methyl methacrylate) (PS-b-PMMA) diblock copolymers of molecular weight M_n = 29,700 g mol⁻¹ (M_PS = 9300 g mol⁻¹M_PMMA = 20,100 g mol⁻¹, PD = 1.15, χ_PS = 0.323, χ_PMMA = 0.677) and M_n = 63,900 g mol⁻¹ (M_PS = 50,500 g mol⁻¹, M_PMMA = 13,400 g mol⁻¹, PD = 1.18, χ_PS = 0.790, χ_PMMA = 0.210) were prepared via reversible addition-fragmentation chain transfer (RAFT) polymerization. Atomic force microscopy (AFM) was used to investigate the surface structure of thin films, prepared by spin-coating the diblock copolymers on a silicon substrate. We show that the nanostructure of the diblock copolymer depends on the molecular weight and volume fraction of the diblock copolymers. We observed a perpendicular lamellar structure for the high molar mass sample and a hexagonal-packed cylindrical patterning for the lower molar mass one. Small-angle X-ray scattering investigation of these samples without annealing did not reveal any ordered structure. Annealing of PS-b-PMMA samples at 160 °C for 24 h led to a change in surface structure.     

Thermal aggregation of bovine serum albumin studied by asymmetrical flow field-flow fractionation

The use of asymmetrical flow field-flow fractionation (AsFlFFF) in the study of heat-induced aggregation of proteins is demonstrated with bovine serum albumin (BSA) as a model analyte. The hydrodynamic diameter (d_h), the molar mass of heat-induced aggregates, and the radius of gyration (R_g) were calculated in order to get more detailed understanding of the conformational changes of BSA upon heating. The hydrodynamic diameter of native BSA at ambient temperature was ∼7 nm. The particle size was relatively stable up to 60 °C; above 63 °C, however, BSA underwent aggregation (growth of hydrodynamic diameter). The hydrodynamic diameters of the aggregated particles, heated to 80 °C, ranged from 15 to 149 nm depending on the BSA concentration, duration of incubation, and the ionic strength of the solvent. Heating of BSA in the presence of sodium dodecyl sulfate (1.7 or 17 mM) did not lead to aggregation. The heat-induced aggregates were characterized in terms of their molar mass and particle size together with their respective distributions with a hyphenated technique consisting of an asymmetrical field-flow fractionation device and a multi-angle light scattering detector and a UV-detector. The carrier solution comprised 8.5 mM phosphate and 150 mM sodium chloride at pH 7.4. The weight-average molar mass (M_w) of native BSA at ambient temperature is 6.6 × 10⁴ g mol⁻¹. Incubation of solutions with BSA concentrations of 1.0 and 2.5 mg mL⁻¹ at 80 °C for 1 h resulted in aggregates with M_w 1.2 × 10⁶ and 1.9 × 10⁶ g mol⁻¹, respectively. The average radius of gyration and the average hydrodynamic radius of the heat-induced aggregate samples were calculated and compared to the values obtained from the size distributions measured by AsFlFFF. For comparison static light scattering measurements were carried out and the corresponding average molar mass distributions of solutions with BSA concentrations of 1.0 and 2.5 mg mL⁻¹ at 80 °C for 1 h gave aggregates with M_w 1.7 × 10⁶ and 3.5 × 10⁶ g mol⁻¹, respectively.     

The influence of chain rigidity on the thermal properties of some novel random copolyethersulfones

Some random low molar mass (M_n ≈ 9000 g mol⁻¹) poly(ethersulfoneethersulfone)/poly(ethersulfoneethersulfonebiphenylsulfone) P(ESES)/P(ESESBS) copolymers, with various (25%, 50% and 75%) ESESBS units contents, were synthesized to obtain compounds with higher chain rigidity than PES. The thermal characterization of the prepared copolymers, as well as that of corresponding P(ESES) and P(ESESBS) homopolymers, was performed, and all investigated parameters showed strong dependence on polymer composition.The glass transition temperature (T_g) was calorimetrically determined by DSC technique, and the obtained values increased linearly as function of ESESBS units percentage, thus indicating an increasing chain rigidity.Degradations were carried out in dynamic heating conditions, from 35 °C to 700 °C, in both flowing nitrogen and static air atmosphere, and the characteristic parameters of degradation were determined in order to draw useful information about the overall thermal stability of the studied compounds. The apparent activation energy of degradation (E_a) was obtained by the Kissinger method, and the values found increased linearly as a function of ESESBS content, while the temperature values at 5% mass loss (T_5%) showed an opposite linear trend. The results are discussed and interpreted.     

Thermal properties and stability of cassava starch films cross-linked with tetraethylene glycol diacrylate

The thermal stability of starch cross-linked with tetraethylene glycol diacrylate was studied under nitrogen atmosphere by thermogravimetry (TG) and infrared spectroscopy (FTIR). The cross-linking reaction was confirmed by the increase in intensity of the absorption band at ca. 3330 cm⁻¹ indicating the reinforcement of hydrogen bonds and the appearance of a new band at 1726 cm⁻¹ associated with the carbonyl group of the cross-linking agent. After cross-linking the solubility of starch in water decreased to the range 9%-16%. The thermogravimetric curves of pure and cross-linked starches showed an initial stage of degradation (up to ca. 150 °C) associated with the loss of water. The main stage of degradation occurred in the range 250-400 °C corresponding to ca. 60%-70% mass loss. The activation energy (E) for the degradation process increased from 145 kJ mol⁻¹ (pure starch) to 195 kJ mol⁻¹ and 198 kJ mol⁻¹ for starch treated for 60 min by UV (30 °C) and at 90 °C, suggesting high stability after cross-linking. A higher value (240 kJ mol⁻¹) was obtained for starch treated by UV for 120 min. The main volatile products determined by FTIR which correspond to hydrocarbons and carbonyl groups are apparently associated with the scission of weak bonds in the chain (probably branched groups) and the scission of stronger bonds (glycosidic linkages), respectively.     

Living radical polymerisation in heterogeneous conditions—suspension polymerisation

Transition metal mediated living radical polymerisation of butyl methacrylate has been demonstrated with a copper(I) halide N-alkyl-2-pyridylmethanimine ligands based catalyst. Optimum conditions were found to be with copper(I) chloride and N-octyl-2-pyridylmethanimine catalyst at 65 °C where conversions of 85% were achieved with polymers of M_n = 8900 g mol⁻¹ (theoretical = 8400 g mol⁻¹) and PDI = 1.23. Both non-ionic and ionic surfactants were employed which were also made by living radical polymerisation. The non-ionic surfactant was a block copolymer of PMMA from a polyethyleneglycol macroinitiator (total M_n = 7600 g mol⁻¹, PDI = 1.20) and the ionic surfactant PDMEAMA-PMMA (total M_n = 8000 g mol⁻¹, PDI = 1.21) with the PDMEAMA block quaternized with MeI (13.8%, 28.4%, 47.7% and 100%). A range of ligands were employed in the suspension polymerisation by varying the alkyl group on the ligand increasing the hydrophobicity (alkyl = propyl (PrMI), pentyl (PMI), octyl (OMI), dodecyl (DMI) and octadecyl (ODMI)). The more hydrophobic ligands were found to be more effective due to lower partitioning into the aqueous phase. Block copolymers of P(EMA)-P(BMA) and P(MMA)-P(BMA) were prepared by first preparing macroinitiators via living radical polymerisation (M_n = 1600 g mol⁻¹ (PDI = 1.23) for P(EMA) and M_n = 1500 g mol⁻¹ (PDI = 1.22) for P(MMA)) and using them for initiation of BMA in suspension polymerisation. Block copolymers had M_n between 12,800 and 13,700 g mol⁻¹ with PDI between 1.33 and 1.54. Block copolymer growth showed excellent linear first order kinetics wrt monomer and demonstrated characteristics expected of a living radical polymerisation. Particle sizes were measured by SEM and DLS with good agreement (1.4-2.8 μm) and SEM showed spherical particles were formed.     

Crystal structure and the standard molar enthalpy of formation of a coordination polymer [Cu(nip)(phen)]n

A coordination polymer [Cu(nip)(phen)]_n was hydrothermally synthesized by the reaction of Cu(NO₃)₂ with 5-nitroisophthalic acid and phen. Single-crystal structure analysis showed that the complex crystallized in the monoclinic space group P2₁/c; a = 10.6566(13); b = 12.5931(15); c = 13.0514(16) Å; β = 95.474(2)°, V = 1743.5(4) Å³; Z = 4. The standard molar enthalpy of formation of the complex was determined to be −554 ± 11 kJ mol⁻¹.     

Enthalpy change and mechanism of oxidation of o-phenylenediamine by hydrogen peroxide catalyzed by horseradish peroxidase

The hydrogen peroxide-oxidation of o-phenylenediamine (OPD) catalyzed by horseradish peroxidase (HRP) at 37 °C in 50 mM phosphate buffer (pH 7.0) was studied by calorimetry. The apparent molar reaction enthalpy with respect to OPD and hydrogen peroxide were −447 ± 8 kJ mol⁻¹ and −298 ± 9 kJ mol⁻¹, respectively. Oxidation of OPD by H₂O₂ catalyzed by HRP (1.25 nM) at pH 7.0 and 37 °C follows a ping-pong mechanism. The maximum rate V_max (0.91 ± 0.05 μM s⁻¹), Michaelis constant for OPD K_m,S (51 ± 3 μM), Michaelis constant for hydrogen peroxide Km,H₂O₂ (136 ± 8 μM), the catalytic constant k_cat (364 ± 18 s⁻¹) and the second-order rate constants k₊₁ = (2.7 ± 0.3) × 10⁶ M⁻¹ s⁻¹ and k₊₅ = (7.1 ± 0.8) × 10⁶ M⁻¹ s⁻¹ were obtained by the initial rate method.     

Heat capacity, enthalpy and entropy of ternary bismuth tantalum oxides

Heat capacity and enthalpy increments of ternary bismuth tantalum oxides Bi₄Ta₂O₁₁, Bi₇Ta₃O₁₈ and Bi₃TaO₇ were measured by the relaxation time method (2-280 K), DSC (265-353 K) and drop calorimetry (622-1322 K). Temperature dependencies of the molar heat capacity in the form C_pm=445.8+0.005451T−7.489×10⁶/T² J K⁻¹ mol⁻¹, C_pm=699.0+0.05276T−9.956×10⁶/T² J K⁻¹ mol⁻¹ and C_pm=251.6+0.06705T−3.237×10⁶/T² J K⁻¹ mol⁻¹ for Bi₃TaO₇, Bi₄Ta₂O₁₁ and for Bi₇Ta₃O₁₈, respectively, were derived by the least-squares method from the experimental data. The molar entropies at 298.15 K, S°_m(298.15 K)=449.6±2.3 J K⁻¹ mol⁻¹ for Bi₄Ta₂O₁₁, S°_m(298.15 K)=743.0±3.8 J K⁻¹ mol⁻¹ for Bi₇Ta₃O₁₈ and S°_m(298.15 K)=304.3±1.6 J K⁻¹ mol⁻¹ for Bi₃TaO₇, were evaluated from the low-temperature heat capacity measurements.     

Reverse atom transfer radical polymerisation (RATRP) of methacrylates using copper(I)/pyridinimine catalysts in conjunction with AIBN

N-n-Propyl-2-pyridylmethanimine, 1, N-n-octyl-2-pyridylmethanimine, 2, N-n-lauryl-2-pyridylmethanimine, 3, and N-n-octadecyl-2-pyridylmethanimine, 4 have been used in conjunction with copper(II) bromide and azo initiators for the reverse atom transfer radical polymerisation of a range of methacrylates. AIBN to Cu^IIBr₂ ratios of 0.5:1, 0.75:1 and 1:1 give PMMA with M_n 11 500 g mol⁻¹ (PDi = 1.24) (at 22% conversion), 12 500 g mol⁻¹ (PDi = 1.06) (at 83% conversion) and 10 900 g mol⁻¹ (PDi = 1.11) (at 84% conversion), respectively. A Cu^IIBr₂ complex is demonstrated to be needed at the start of the reaction for good control over molecular weight and polydispersity as reactions using Cu(I)Br as catalyst yielded PMMA of M_n 31 000 g mol⁻¹ (PDi = 2.90), reactions with no copper yield PMMA of M_n 33 000 g mol⁻¹ (PDi = 2.95). The RATRP of styrene was carried out using Cu^IIBr₂ as catalyst. AIBN to Cu^IIBr₂ ratio of 0.5:1, 0.75:1 and 1:1 gave PS with M_n = 12 400 g mol⁻¹ (PDi = 1.27) at low conversion, M_n = 15 500 g mol⁻¹ (PDi = 1.11) and 12 400 g mol⁻¹ (PDi = 1.38), respectively at ∼85% conversion. A series of block copolymers of MMA with BMA, BzMA and DMEAMA (15 600 g mol⁻¹ (PDi = 1.18), 13 300 g mol⁻¹ (PDi = 1.14) 15 300 g mol⁻¹ (PDi) = 1.16), using a PMMA macroinitiator were prepared. Emulsion polymerisation of MMA using [initiator]:[Cu^(II)Br₂] ratio = 0.5:1 with Brij surfactant gave a linear increase of M_n with respect to conversion, final M_n = 112 800 g mol⁻¹ (PDi = 1.42). Further reactions were carried out with [initiator]:[Cu^(II)Br₂] ratio = 0.75:1 and 1:1. Both giving PMMA with M_n ∼ 32 000 g mol⁻¹ (PDi ∼ 2.4). These reactions exhibit no control, this is because the azo initiator is present in excess and all of the monomer is consumed by a free radical polymerisation as opposed to a controlled reaction. Particle size analysis (DLS) showed the particle size between 160 and170 nm in all cases.     

Bacterial polyesters grafted with poly(ethylene glycol): Behaviour in aqueous media

An easy method for grafting of poly(3-hydroxyoctanoate-co-3-hydroxyundecenoate) (PHOU) was developed. Oxidation of the pendant double bonds of PHOU into carboxyl groups to yield poly(3-hydroxyoctanoate-co-3-hydroxy-9-carboxydecanoate) (PHOD) and the esterification of the carboxyl side groups with poly(ethylene glycol) (PEG) were carried out in a single reaction solution. The grafting yield is dependent on the molar mass of the PEG graft. The maximum carboxyl group conversion (52%) was obtained with PEG M_n = 350 and decreased with increasing molar mass of PEG (19% for PEG M_n = 2000). Yields were determined by ¹H and ¹³C NMR. Short PEG grafts lowered the glass transition temperature (PHOD-g-PEG 350 −57 °C) compared to PHOD (−19 °C) and PHOU (−39 °C). This effect depends on the COOH conversion and PEG chain length. Grafting enhanced the hydrophilic character of the modified polymers making them soluble in polar solvents, such as alcohols and water/acetone mixtures. PHOD-g-PEG films were more stable towards hydrolytic degradation as PHOD films. No obvious modification of films was observed after more than 200 days at pH 7.2 and 37 °C. The molar mass of the grafted polymers decreased only slightly during this period, while PHOD films were hydrolyzed into soluble fragments.     

Thermodynamics of BaNd2Fe2O7(s) and BaNdFeO4(s) in the system BaNdFeO

Two compounds, BaNd₂Fe₂O₇(s) and BaNdFeO₄(s) in the quaternary system BaNdFeO were prepared by citrate-nitrate gel combustion route and characterized by X-ray diffraction analysis. Heat capacities of these two oxides were measured in two different temperature ranges: (i) 130-325 K and (ii) 310-845 K, using a heat flux type differential scanning calorimeter. Two different types of solid-state electrochemical cells with CaF₂(s) as the solid electrolyte were employed to measure the e.m.f. as a function of temperature. The standard molar Gibbs energies of formation of these quaternary oxides were calculated as a function of temperature from the e.m.f. data. The standard molar enthalpies of formation from elements at 298.15 K, ΔfHm° (298.15 K) and the standard entropies, Sm° (298.15 K) of these oxides were calculated by the second law method. The values of ΔfHm° (298.15 K) and Sm° (298.15 K) obtained for BaNd₂Fe₂O₇(s) are: −2756.9 kJ mol⁻¹ and 234.0 J K⁻¹ mol⁻¹ whereas those for BaNdFeO₄(s) are: −2061.5 kJ mol⁻¹ and 91.6 J K⁻¹ mol⁻¹, respectively.     

A solution-reaction isoperibol calorimeter and standard molar enthalpies of formation of Ln(hq)2Ac (Ln = La, Pr)

An on-line solution-reaction isoperibol calorimeter has been constructed. The performance of the apparatus was evaluated by measuring the molar enthalpy of solution of KCl in water at 298.15 K. The uncertainty and the inaccurary of the experimental results were within ±0.3% compared with the recommended reference data. Using the calorimeter, the molar enthalpies of reaction for the following two reactions: LaCl₃·7H₂O(s)+2Hhq(s)+NaAc(s)=La(hq)₂Ac(s)+NaCl(s)+2HCl(g)+7H₂O(l) and PrCl₃·6H₂O(s)+2Hhq(s)+NaAc(s)=Pr(hq)₂Ac(s)+NaCl(s)+2HCl(g)+6H₂O(l), were determined at T=298.15 K, as −(78.3±0.6) and −(97.3±0.5) kJ mol^−l, respectively. From the above molar enthalpies of reaction and other auxiliary thermodynamic quantities, the standard molar enthalpies of formation of La(hq)₂Ac and Pr(hq)₂Ac, at T=298.15 K, have been derived to be −(1535.5±0.7) and −(1536.7±0.6) kJ mol^−l, respectively.     

Study of the in vitro degradation of poly(ethyl glyoxylate)

In vitro degradation of poly(ethyl glyoxylate) (PEtG), a functionalised polyacetal, was investigated. First, the thermodynamic polymerization parameters and the ceiling temperature (T_c) were determined (ΔH_p = 28 ± 3 kJ mol⁻¹, ΔS_p = 98 ± 7 J mol⁻¹ K⁻¹, T_c = 310 ± 4 K). Secondly, PEtG hydrolysis was investigated using potentiometry, weight loss measurements, SEC and ¹H NMR. The results show that PEtG is stable for at least 7 days in aqueous media. Then degradation occurs and releases ethanol and glyoxylic acid hydrate as final products. A scheme for the degradation mechanism involving chain scission and ester hydrolysis is proposed.     

Heat-capacity measurements and thermodynamic functions of crystalline adenine; revised thermodynamic properties of aqueous adenine

The standard molar heat capacity C^°_p,m of adenine(cr) has been measured using adiabatic calorimetry over the range 6<(T/K)<310 and the results used to derive thermodynamic functions for adenine(cr) at smoothed temperatures. At T=298.15 K, C^°_p,m=(142.67±0.29) J · K⁻¹ · mol⁻¹ and the third law entropy S^°_m=(145.62±0.29) J · K⁻¹ · mol⁻¹. The standard molar Gibbs free energy of formation Δ_fG^°_m at T=298.15 K for crystalline adenine was calculated, using the standard molar enthalpy of formation for the compound and entropies of the elements from the literature, and found to be Δ_fG^°_m=(301.4±1.0) kJ · mol⁻¹. The results were combined with solution calorimetry and solubility measurements from the literature to yield revised values for the standard molar thermodynamic properties of aqueous adenine at T=298.15 K: Δ_fG^°_m=(313.4±1.0) kJ · mol⁻¹, Δ_fH^°_m=(129.5±1.4) kJ · mol⁻¹, and S_m^°=(217.68±0.44) J · K⁻¹ · mol⁻¹.     

Synthesis, characterization, thermal stability and electrochemical properties of poly-4-[(2-methylphenyl)iminomethyl]phenol

In this study, the reaction conditions of poly-4-[(2-methylphenyl)iminomethyl]phenol (P-2-MPIMP) were studied by using oxidants such as air O₂, H₂O₂ and NaOCl in an aqueous alkaline medium between 50 and 90 °C. The structures of the synthesized monomer and polymer were confirmed by FT-IR, UV-vis, NMR and elemental analysis. The characterization was made by TG-DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly-4-[(2-methylphenyl)iminomethyl]phenol (P-2-MPIMP) was found to be 20% (for air O₂ oxidant), 33% (for H₂O₂ oxidant), and 74% (for NaOCl oxidant). According to the SEC analysis, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of P-2-MPIMP were found to be 3300, 4100 g mol⁻¹ and 1.242, using H₂O₂, and 4550, 5150 g mol⁻¹and 1.132, using air O₂ and 5300, 5850 g mol⁻¹ and 1.104, using NaOCl, respectively. According to TG analysis, the weight losses of 4-[(2-methylphenyl)iminomethyl]phenol (2-MPIMP) and P-2-MPIMP were found to be between 75.29% and 48.17% at 1000 °C, respectively. P-2-MPIMP was shown to have a higher stability against thermal decomposition. Also, electrical conductivity of the P-2-MPIMP was measured, showing that the polymer is a typical semiconductor. Electrochemically, the highest occupied molecular orbital (HOMO), the lowest unoccupied molecular orbital (LUMO) and electrochemical energy gaps ( of 2-MPIMP and P-2-MPIMP were found to be −6.01, −6.03; −2.63, −2.82; 3.38 and 3.21 eV, respectively. According to UV-vis measurements, the optical band gap (E_g) of 2-MPIMP and P-2-MPIMP was found to be 3.40 and 2.97 eV, respectively.     

Synthesis, characterization and thermal degradation of oligo-2-[(4-fluorophenyl) imino methylene] phenol and some of its oligomer-metal complexes

In this study, the oxidative polycondensation reaction conditions of 2-[(4-fluorophenyl) imino methylene] phenol (FPIMP) with air oxygen and NaOCl were studied in an aqueous alkaline medium between 60 and 90 °C. Synthesized oligo-2-[(4-fluorophenyl) imino methylene] phenol was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. The yield of oligo-2-[(4-fluorophenyl) imino methylene] phenol (OFPIMP) was found to be 62.00% (for air O₂ oxidant) and 97.70% (for NaOCl oxidant) at the optimum reaction conditions. According to the SEC analysis, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of OFPIMP were found to be 1370 g mol⁻¹, 1979 g mol⁻¹ and 1.45, using NaOCl, 2105 g mol⁻¹, 2557 g mol⁻¹, and 1.22, using air O₂, respectively. During the oxidative polycondensation reaction, (2.88%) a part of -CHN group oxidized to carboxylic acid (-COOH). TG and TG-DTA analyses were shown to be more stable of oligo-2-[(4-fluorophenyl) imino methylene] phenol and its oligomer metal complexes than monomer against thermo-oxidative decomposition. The weight loss of OFPIMP was found to be 97.00% at 900 °C. The weight losses of OFPIMP-Co, OFPIMP-Ni OFPIMP-Cu oligomer-metal complex compounds were found to be 88.66%, 94.36% and 83.21%, respectively, at 1000 °C.     

Comparison of pyrimethanil-imprinted beads and bulk polymer as stationary phase by non-linear chromatography

A pyrimethanil-imprinted polymer (P1) was prepared by iniferter-mediated photografting a mixture of methacrylic acid and ethylene dimethacrylate onto homemade near-monodispersed chloromethylated polydivinylbenzene beads. The chromatographic behaviour of a column packed with these imprinted beads was compared with another column packed with irregular particles obtained by grinding a bulk pyrimethanil-imprinted polymer (P2). The comparison was made using the kinetic model of non-linear chromatography, studying the elution of the template and of two related substances, cyprodinil and mepanipyrim. Extension of the region of linearity, capacity factors for the template and the related substances, column selectivity, binding site heterogeneity, apparent affinity constant (K) and lumped kinetic association (k_a) and dissociation rate constant (k_d) were studied during a large interval of solute concentration, ranging between 1 and 2000 μg/ml. From the experimental results obtained, in the linearity region of solute concentration column selectivity and binding site heterogeneity remained essentially the same for the two columns, while column capacity (at 20 μg/ml, P1 = 23.1, P2 = 11.5), K (at 20 μg/ml, P1 = 8.3 × 10⁶ M⁻¹, P2 = 2.5 × 10⁶ M⁻¹) and k_a (at 20 μg/ml, P1 = 3.5 μM⁻¹ s⁻¹, P2 = 0.47 μM⁻¹ s⁻¹) significantly increased and k_d (at 20 μg/ml, P1 = 0.42 s⁻¹, P2 = 0.67 s⁻¹) decreased for the column packed with the imprinted beads. These results are consistent with an influence of the polymerisation method on the morphology of the resulting polymer and not on the molecular recognition properties due to the molecular imprinting process.     

2π + 2π cycloaddition kinetics of some fluoro olefins and fluoro vinyl ethers

The second order 2π + 2π homo- and co-dimerization between various classes of fluorinated olefins has been investigated. The fluorinated olefins examined in this study were: (1) R_fOCFCF₂ (perfluorinated vinyl ethers); (2) R_fCFCF₂ (perfluorinated terminal olefins); (3) RCH₂CFCF₂; (4) PhOCFCF₂ (aryl perfluorinated vinyl ethers).Homo-dimerizations between vinyl ethers have an E_a between 20 and 24 kcal mol⁻¹ while homo-dimerizations between terminal olefins have an average E_a between 35 and 40 kcal mol⁻¹; vinyl groups have a second order cyclodimerization rate constant of formation between 1 × 10⁻⁷ and 1 × 10⁻⁴ M⁻¹ S⁻¹ while vinyl ethers have a second order cyclodimerization rate constant of formation = 1 × 10⁻¹ M⁻¹ s⁻¹. If there is a CH₂ group α to the terminal olefin, the E_a of cyclodimerization is about 7 kcal mol⁻¹) lower with respect to those olefins with a CF₂ α to the instauration. At 270 °C co-dimerizations have an average ΔS^≠ = −45 cal K⁻¹ mol⁻¹ and a second order rate constant of cyclodimerization ranging between 0.1 × 10⁻⁴ M⁻¹ S⁻¹ and 16 × 10⁻⁴ M⁻¹ S⁻¹ while homo-dimerizations have an average ΔS^≠ = −17 cal K⁻¹ mol⁻¹ and a second order rate constant which can span from 7 × 10⁻⁷ M⁻¹ S⁻¹ to as much as 1 × 10⁻¹ M⁻¹ S⁻¹ depending on the electronic nature of the perfluorinated terminal olefin.A good correlation between the electronegativity χ and the activation energy E_a demonstrates that “polarizing” groups, O, PhO, α to the olefin play an important role in the formation and stabilization of the cyclodimerization biradical intermediate.     

Swelling behaviour of thermo-sensitive hydrogels based on oligo(ethylene glycol) methacrylates

The thermo-sensitive swelling behaviour of hydrogels based on 2-(2-methoxyethoxy)ethyl methacrylate (MEO₂MA) and synthesized by free radical polymerization has been investigated. The homopolymer hydrogel presents a low critical solution temperature (LCST) close to room temperature, which can be modulated by copolymerization with longer oligo(ethylene glycol) side chain methacrylates (OEG_xMA). Then, three series of copolymeric hydrogels synthesized with MEO₂MA and several low ratios of OEG_xMA with M_n = 475 g mol⁻¹ (OEG₈MA), M_n = 1100 g mol⁻¹ (OEG₂₃MA) and M_n = 2080 g mol⁻¹ (OEG₄₅MA) were studied. In addition to conventional tetra(ethylene glycol) dimethacrylate (TEGDMA) crosslinker, the use of biodegradable oligo(caprolactone) dimethacrylate (OCLDMA) was also tested. The hydrophilic/hydrophobic balance, function of the short and the long OEG side chains, establishes a swelling behaviour depending on monomer composition, side chain length and temperature. The swelling at equilibrium increases with increasing the amount of OEG_xMA in the copolymer and, at the same time, the collapsing moves progressively to higher temperature. The temperature dependent volumetric response of some of these hydrogels can be compare with the most extended thermo-sensitive hydrogel, which is based on poly(N-isopropylacrylamide) (P(N-iPAAm)). Therefore, they are potential candidates to replace it in applications where biocompatibility is required.