Structural and conductivity changes during the pyrolysis of polyaniline base

Polyaniline base has been exposed to various temperatures between 100 °C and 1000 °C for 2 h in air. The mass loss has increased with increasing temperature. FTIR and Raman spectroscopies show the gradual destruction of the PANI structure, the possible formation of intermediate oxime and nitrile groups, and the final conversion to graphitic material. The elemental analysis confirmed the dehydrogenation while the content of nitrogen was nearly constant even after treatment at 800 °C. The conductivity of PANI base, 10⁻⁸ S cm⁻¹, increased to ∼10⁻⁴ S cm⁻¹ after treatment at 1000 °C; most of the products, however, were non-conducting. Another series of experiments involved the polyaniline base heated at 500 °C for 1-8 h. The studies were performed in connection with the potential flame-retardant application of polyaniline.     

Brønsted acid-base polymer electrolyte membrane based on sulfonated poly(phenylene oxide) and imidazole

The Brønsted acid-base polymer electrolyte membrane was prepared by entrapping imidazole in sulfonated poly(phenylene oxide) at the molar ratio of Im/SPPO = 2:1. The hybrid showed a high thermal stability up to 200 °C and peroxide tolerance. Differential scanning calorimetry shows that glass transition temperature is 232 °C. The conductivity increases with temperature exceeding 10⁻³ S/cm above 120 °C and a high conductivity of 6.9 × 10⁻³ S/cm was obtained at 200 °C under 33% RH conditions.     

Thermal stability and structure of electroactive polyaniline-fluoroboric acid-dodecylhydrogensulfate salt

Oxidation of aniline by emulsion polymerization pathway using benzoyl peroxide oxidant in the presence of fluoroboric acid and sodium lauryl sulfate surfactant leads to incorporation of both acid group as well as surfactant group onto the polyaniline chain as dopants i.e. formation of polyaniline-fluoroboric acid-dodecylhydrogensulfate salt (PANI-HBF₄-DHS). Amount of dopants such as fluoroboric acid (HBF₄), dodecylhydrogensulfate (DHS) and water present in the PANI-HBF₄-DHS was found out for the first time. Electrochemical activity and rheological stability of the polymer were determined. Thermal stability of PANI-HBF₄-DHS was determined by subjecting the polyaniline salt in macroscale at four different temperatures (100, 150, 200 and 250 °C). Structure, composition and thermal stability of polyaniline salt were determined by chemical analysis, conductivity, IR, UV/vis, XRD spectral measurements from the heat treated samples. Polyaniline salt contains 8.3 wt% water, 22.4 wt% HBF₄ and 15.4 wt% DHS at ambient temperature. Upon vacuum, polyaniline salt loses 4.7 wt% water and on heating the sample at 100 °C it loses the remaining 3.6 wt% water. On further heating polyaniline salt loses its dopants and at 250 °C it loses both the dopants almost completely. Polyaniline salt on heating undergoes cross-linking even at 100 °C and however, conductivity (3 × 10⁻² S/cm) of polyaniline salt was found to remain almost the same up to 150 °C.     

New synthesis of nanopowders of proton conducting materials. A route to densified proton ceramics

Low temperature routes have been developed for the preparation of BaCe_0.9Y_0.1O_2.95 (BCY10) and BaZr_0.9Y_0.1O_2.95 (BZY10) in the form of nanoparticulate powders for use after densification as ceramic membranes for a proton ceramic fuel cell. These methods make use on the one hand of the chelation of metal (II), (III) and (IV) ions by acrylates (hydrogelation route) and on the other of the destabilisation and precipitation of micro-emulsions. Both routes lead to single phase yttrium doped barium cerate or zirconate perovskites, as observed by X-ray diffraction, after thermal treatment at 900 °C for 4 h for BCY10 and 800 °C for BZY10. These temperatures, lower than those usually used for preparation of barium cerate or zirconate, lead to oxide nanoparticles of size <40 nm. Dense ceramics (?95%) are obtained by sintering BCY10 pellets at 1350 °C and BZY10 pellets at 1500 °C for 10 h. The water uptake of compacted samples at 500 °C is 0.14 wt% for BCY10 and 0.26 wt% for BZY10. Total conductivities in the range 300-600 °C were determined using impedance spectroscopy in a humidified nitrogen atmosphere. The total conductivity was 1.8×10⁻² S/cm for BCY10 and 2×10⁻³ S/cm for BZY10 at 600 °C. The smallest perovskite nanoparticles and highest conductivities were obtained by hydrogelation of precursor barium, zirconium, cerium and yttrium acrylates.     

Preparation and characterization of fluorine-containing polybenzimidazole/imidazole hybrid membranes for proton exchange membrane fuel cells

Polybenzimidazole (PBI)/imidazole (Im) hybrid membranes were prepared from an organosoluble, fluorine-containing PBI with Im. The thermal decomposition of the PBI/Im hybrid membranes occurred at about 160 °C. The conductivities of the acid doped PBI/Im hybrid membranes increased with both the temperature and the Im content. The conductivity of acid doped PBI-40Im (molar ratio of Im/PBI = 40) reached 3.1 × 10⁻³ (S/cm) at 160 °C. The proton conductivities of PBI/Im hybrid membranes were over 2 × 10⁻³ (S/cm) at 90 °C and 90% relative humidity. The addition of Im could reduce the mechanical properties and methanol barrier ability of the PBI membranes.     

Synthesis of nanospherical Fe3BO6 anode material for lithium-ion battery by the rheological phase reaction method

This paper developed a novel method, the rheological phase reaction method, to synthesize nanospherical Fe₃BO₆. The sizes and morphologies of products vary with the calcination temperatures. Spherical particles with a uniform size about 40 nm in a monodisperse state were obtained at 800 °C, while the spherical particles with a larger size of 100-500 nm were obtained at 900 °C. The electrochemical properties of these Fe₃BO₆ nanospheres were investigated. Sample synthesized at 800 °C delivers a high reversible capacity above 500 mAh g⁻¹. Sample synthesized at 900 °C possesses relatively good cycleability with a capacity retaining of 376 mAh g⁻¹ after 10 cycles. The measurement of electrochemical impedance spectra for the first time indicated that smaller Fe₃BO₆ nanoparticles intend to give higher impedance of solid-electrolyte interface layer and lower charge-transfer impedance after the first discharge. Additionally, it can be speculated that the increase of resistance charge-transfer is the possible reason for the capacity fading during cycling.     

New solid-state synthesis routine and mechanism for LiFePO4 using LiF as lithium precursor

Li₂CO₃ and LiOH·H₂O are widely used as Li-precursors to prepare LiFePO₄ in solid-phase reactions. However, impurities are often found in the final product unless the sintering temperature is increased to 800 °C. Here, we report that lithium fluoride (LiF) can also be used as Li-precursor for solid-phase synthesis of LiFePO₄ and very pure olivine phase was obtained even with sintering at a relatively low temperature (600 °C). Consequently, the product has smaller particle size (about 500 nm), which is beneficial for Li-extraction/insertion in view of kinetics. As for cathode material for Li-ion batteries, LiFePO₄ obtained from LiF shows high Li-storage capacity of 151 mAh g⁻¹ at small current density of 10 mA g⁻¹ (1/15 C) and maintains capacity of 54.8 mAh g⁻¹ at 1500 mA g⁻¹ (10 C). The solid-state reaction mechanisms using LiF and Li₂CO₃ precursors are compared based on XRD and TG-DSC.     

Influence of carbon shell structure on electrochemical performance of multi-walled carbon nanotube electrodes

Core/shell nanostructures have received considerable attention due to the synergistic effect of their combination of materials. In this work, core/shell carbon/multi walled carbon nanotubes (MWNTs) (C-MWNTs) composed of core MWNTs and carbon shells were prepared to obtain a new type of carbon electrode materials. Carbon shells containing nitrogen groups were prepared by coating polyaniline (PANI) onto the MWNTs by in situ polymerization and subsequent carbonization at 850 °C. After carbonization, the C-MWNTs contained 5.84% nitrogen and showed a hollow structure and crystallinity like that of pristine MWNTs. In addition, the C-MWNTs exhibited electrochemical performance superior to that of pristine MWNTs, and the highest specific capacitance (231 F g⁻¹) of the C-MWNTs was obtained at a scan rate of 0.1 A g⁻¹, as compared to 152 F g⁻¹ for pristine MWNTs. This superior performance is attributed to the maintenance of high electrical conductivity by the π–π interaction between the carbon layer and the MWNTs, increased specific surface area of C-MWNTs, and the presence of nitrogen groups formed on the carbon electrode after the carbonization of the shell PANI.     

Thermoelectric properties of HPHT sintered In-doped Pb0.5Sn0.5Te

The thermoelectric properties of Pb_0.5Sn_0.5Te doped with In at 1.0, 2.0, and 3.0×10¹⁹/cm³ and sintered at a high pressure and high temperature (HPHT) of 4.0 GPa and 800 or 900 °C, respectively, have been studied. All samples show p-type semiconducting behavior with positive thermopower. We find that HPHT sintering of conventionally synthesized materials improves their thermoelectric properties. The highest power factor is obtained for In doping of 2.0×10¹⁹/cm³ with 13.5 μW/cm K² at 230 °C. The corresponding figure of merit is 1.43×10⁻³/K. This represents a twofold improvement in thermoelectric figure of merit, compared to the conventionally sintered materials reported in the literature. When exposed to 400 °C for 10 days, samples sintered at 900 °C exhibit more stable thermoelectric properties, while the properties of those sintered at 800 °C deteriorated. These results demonstrate that HPHT sintering is a viable and controllable way of tuning the thermoelectric properties of PbTe-based materials.     

TCF selenium preconcentration in geological materials for determination at sub-mugg(-1) with INAA (Se/TCF-INAA)

In geological samples, Se concentration ranges from 1 × 10⁻⁹ g g⁻¹ up to 1 × 10⁻³ g g⁻¹. The analytical difficulty at low concentration (<1 μg g⁻¹), is one of the main reasons why the geological cycle of Se is poorly known. The analytical method that consisted of preconcentration of Se with thiol cotton fiber (TCF) followed by graphite furnace atomic absorption spectrometry (GFAAS) has been modified by finishing with instrumental neutron activation analysis (INAA). The modified technique involves sample dissolution (HF-HNO₃-H₂O₂) and evaporation to dryness at low temperature (55-60 °C) to avoid selenium volatilization. Se^VI is converted to Se^IV by adding 6 M HCl to the dry residuum and the solution is then heated in a covered boiling bath (95-100 °C). The solution is diluted to obtain 0.6 M HCl and then collected on TCF. The TCF is placed in a polyethylene vial for irradiation in the SLOWPOKE II reactor (Montréal) for 30 s at a neutron flux of 10¹⁵ m⁻² s⁻¹. The 162 keV peak of ^77mSe (half-life 17.36 s) is read for 20 s after a decay of 7 s. The amount of sample to be dissolved is controlled by two competing effects. To obtain low detection limits, a larger amount of sample should be dissolved. On the other hand, the TCF could become saturated with chalcophile elements when large sample is used. Sulfur is a good indicator of the amount of Se and chalcophile elements present. In S poor sample (<100 μg g⁻¹) 3.0 g of sample was used and the L_D was ∼2 ng g⁻¹. In S high samples (>1.5% S) 0.05 g of sample was used and the L_D was ∼120 ng g⁻¹. The present work also includes suggested Se concentration for eight international geological reference materials (IGRM) that compare favorably with literature values.     

Determination of cadmium and lead in cetacean Dolphinidae tissue from the coast of Bahia state in Brazil by GFAAS

In the present study, cadmium and lead in the muscle, lung, liver and kidney of dolphins (Sotalia guianensis and Stenella clymene) of the Bahia coast in the northwest of Brazil were determined by graphite furnace atomic absorption spectrometry. Samples were digested using a diluted oxidant mixture (HNO₃ + H₂O₂) with a microwave heating program performed in five steps. The optimized temperatures and chemical modifier for the pyrolysis and atomization were 700 °C, 1400 °C and Pd plus Mg for Cd, and 900 °C, 1800 °C and NH₄H₂PO₄ for Pb, respectively. Characteristic masses and limits of detections (n = 20, 3σ) for Cd and Pb were 1.6 and 9.0 pg and 0.82 ng g^− 1 and 0.50 ng g^− 1, respectively. Repeatability ranged from 0.87 to 8.22% for Cd and 4.31 to 8.09% for Pb. The found concentrations presented no statistical differences at the 95% confidence level when compared with the ICP OES methods. Addition and recovery tests were also performed and the results ranged between 87 and 112% for both elements. Samples of cetacean Dolphinidae (S.guianensis and S.clymene) were analyzed, and the higher concentrations ranged from 0.09 to 46.2 µg g^− 1 for Cd and 0.04 to 0.47 µg g^− 1 for Pb in liver, and from 0.133 to 277 µg g^− 1 for Cd in the kidney.     

Titania-lanthanum phosphate photoactive and hydrophobic new generation catalyst

Titania-lanthanum phosphate nanocomposites with multifunctional properties have been synthesized by aqueous sol-gel method. The precursor sols with varying TiO₂:LaPO₄ ratios were applied as thin coating on glass substrates in order to be transparent, hydrophobic, photocatalytically active coatings. The phase compositions of the composite powders were identified by powder X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM). The anatase phase of TiO₂ in TiO₂-LaPO₄ composite precursors was found to be stable even on annealing at 800 °C. The glass substrates, coated with TL1 (TiO₂-LaPO₄ composition with 1 mol% LaPO₄) and TL50 (composite precursor containing TiO₂ and LaPO₄ with molar ratio 1:1) sols and annealed at 400 °C, produced contact angles of 74° and 92°, respectively, though it is only 62° for pure TiO₂ coating. The glass substrates, coated with TL50 sol, produced surfaces with relatively high roughness and uneven morphology. The TL1 material, annealed at 800 °C, has shown the highest UV photoactivity with an apparent rate constant, k_app=24×10⁻³ min⁻¹, which is over five times higher than that observed with standard Hombikat UV 100 (k_app=4×10⁻³ min⁻¹). The photoactivity combined with a moderate contact angle (85.3°) shows that this material has a promise as an efficient self-cleaning precursor.     

Fabrication of polyaniline/carbon nanotube composite modified electrode and its electrocatalytic property to the reduction of nitrite

A polyaniline (PANI)/carbon nanotubes (CNTs) composite modified electrode was fabricated by galvanostatic electropolymerization of aniline on multi-walled carbon nanotubes (MWNTs)-modified gold electrode. The electrode thus prepared exhibits enhanced electrocatalytic behavior to the reduction of nitrite and facilitates the detection of nitrite at an applied potential of 0.0 V. Although the amperometric responses toward nitrite at MWNTs/gold and PANI/gold electrodes have also been observed in the experiments, these responses are far less than that obtained at PANI/MWNTs/gold electrode. The effects of electropolymerization time, MWNTs concentration and pH value of the detection solution on the current response of the composite modified electrode toward sodium nitrite, were investigated and discussed. A linear range from 5.0 × 10⁻⁶ to 1.5 × 10⁻² M for the detection of sodium nitrite has been observed at the PANI/MWNTs modified electrode with a sensitivity of 719.2 mA M⁻¹ cm⁻² and a detection limit of 1.0 μM based on a signal-to-noise ratio of 3.     

The direct decomposition of NO over the La2CuO4 nanofiber catalyst

The NO catalytic direct decomposition was studied over La₂CuO₄ nanofibers, which were synthesized by using single walled carbon nanotubes (CNTs) as templates under hydrothermal condition. The composition and BET specific surface area of the La₂CuO₄ nanofiber were La₂Cu_0.88²⁺Cu_0.12⁺O_3.94 and 105.0 m²/g, respectively. 100% NO conversion (turnover frequency-(TOF): 0.17 g_NO/g_catalyst s) was obtained over such nanofiber catalyst at temperatures above 300 °C with the products being only N₂ and O₂. In 60 h on stream testing, either at 300 °C or at 800 °C, the nanofiber catalyst still showed high NO conversion efficiency (at 300 °C, 98%, TOF: 0.17 g_NO/g_catalyst s; at 800 °C, 96%, TOF: 0.16 g_NO/g_catalyst s). The O₂ and NO temperature programmed desorption (TPD) results indicated that the desorption of oxygen over the nanofibers occurred at 80-190 and 720-900 °C; while NO desorption happened at temperatures of 210-330 °C. NO and O₂ did not competitively adsorb on the nanofiber catalyst. For outstanding the advantage of the nanostate catalyst, the usual La₂CuO₄ bulk powder was also prepared and studied for comparison.     

Self-standing single lithium ion conductor polymer network with pendant trifluoromethanesulfonylimide groups: Li diffusion coefficients from PFGSTE NMR

Solid electrolyte materials have the potential to improve performance and safety characteristics of batteries by replacing conventional solvent-based electrolytes. For this purpose, new candidate single ion conductor self-standing networks were synthesized with trifluoromethane-sulfonylimide (TFSI) lithium salt based monomer using poly(ethyleneglycol) dimethacrylate (PEGDM 750) as crosslinker. The highest ionic conductivity was 3.4 × 10⁻⁷ S cm⁻¹ at 30 °C in the dry state. Thermal and mechanical analyses showed good thermal stability up to 190 °C and rubbery-like properties at ambient temperature. A direct relationship between ionic conductivity and glassy or rubbery state of the membranes was found. Vogel–Tammann–Fulcher behavior was observed in the dry state which is consistent with a lithium conductivity correlated with polymer chain mobility. By swelling the network in propylene carbonate, a self-standing electrolyte gel could be obtained with an ionic conductivity as high as 1 × 10⁻⁴ S cm⁻¹ at 30 °C. The individual diffusion coefficients of mobile species in the material (¹⁹F and ⁷Li) were measured and quantified using pulsed-field gradient nuclear magnetic resonance (PFG-NMR). Diffusion coefficients for the most mobile components of the lithium cations and fluorinated anions at 100 °C in dry membranes have been found to be 3.4 × 10⁻⁸ cm² s⁻¹ and 2.1 × 10⁻⁸ cm² s⁻¹ respectively.     

Preparation of 4(5)-vinylimidazole-co-acrylic acid copolymer and thermal performances related to applicability as PEM fuel cells

A series of acrylic acid and 4(5)-vinylimidazole copolymers for a non-hydrous proton transferring membrane used in polymer electrolyte membrane for fuel cell (PEMFC) are reported. The feed ratio of each monomer results in the variation of copolymer as evaluated by Fourier transform infrared spectroscopy (FTIR), and nuclear magnetic resonance spectroscopy (¹H-NMR). Differential scanning calorimeter and thermal gravimetric analyzer confirm the thermal properties of copolymer films with T_g at 105-177 °C and T_d above 230 °C. The simultaneous analysis of wide angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC) suggests the thermal performance about the decrease in domain size as a consequence of the loss of moisture content in the membrane and the increase in domain size as a consequence of chain mobility after T_g. The proton conductivities under anhydrous condition of the copolymer membranes are in the range of 10⁻² S/cm even up to 120 °C.     

X-ray diffraction study on the thermal expansion behavior of cellulose Iβ and its high-temperature phase

Oriented films of cellulose prepared from algal cellulose were hydrothermally treated to convert them into highly crystalline cellulose Iβ. The lateral thermal expansion behavior of the prepared cellulose Iβ films was investigated using X-ray diffraction at temperatures from 20 to 300 °C. Cellulose Iβ was transformed into the high-temperature phase when the temperature was above 230 °C, allowing the lateral thermal expansion coefficient of cellulose Iβ and its high-temperature phase to be measured. For cellulose Iβ, the thermal expansion coefficients (TECs) of the a- and b-axes were α_a = 9.8 × 10⁻⁵ °C⁻¹ and α_b = 1.2 × 10⁻⁵ °C⁻¹, respectively. This anisotropic thermal expansion behavior in the lateral direction is ascribed to the crystal structure and to the hydrogen-bonding system of cellulose Iβ. For the high-temperature phase, the anisotropy was more conspicuous, and the TECs of the a- and b-axes were α_a = 19.8 × 10⁻⁵ °C⁻¹ and α_b = −1.6 × 10⁻⁵ °C⁻¹, respectively. Synchrotron X-ray fiber diffraction diagrams of the high-temperature phase were also recorded at 250 °C. The cellulose high-temperature phase is composed of a two-chain monoclinic unit cell, a = 0.819 nm, b = 0.818 nm, c (fiber repeat) = 1.037 nm, and γ = 96.4°, with space group = P2₁. The volume of this cell is 4.6% larger than that of cellulose Iβ at 30 °C.     

Preparation and properties of nitrogen-containing hollow carbon nanospheres by pyrolysis of polyaniline-lignosulfonate composites

Polyaniline-lignosulfonate composite hollow spheres were synthesized by using one-step unstirred polymerization of aniline in the presence of lignosulfonate. Novel nitrogen-containing hollow carbon nanospheres were prepared by direct pyrolysis of the polyaniline-lignosulfonate composite spheres at different temperatures under a nitrogen atmosphere. Thermal behavior of the polyaniline-lignosulfonate composite spheres was studied by TG-DTG, FTIR and element analyze instruments. The resultant carbon spheres were characterized by SEM, XRD and nitrogen adsorption-desorption measurement. It was found that the pyrolysis products of the polyaniline-lignosulfonate composite spheres were made up of uniform hollow carbon nanospheres with an average diameter of 135 nm. Furthermore, the hollow carbon nanospheres exhibit high BET surface area range from 381.6 m² g⁻¹ to 700.2 m² g⁻¹. The hollow carbon nanospheres could be used as adsorbents of papain. The papain adsorption capacity for the carbon spheres prepared at 1200 °C was up to 1161 mg g⁻¹ at an initial papain concentration of 10 mg mL⁻¹ at 25 °C.     

Investigation of the quasi-ternary system LaMnO3-LaCoO3-“LaCuO3”—I: the series La(Mn0.5Co0.5)1−xCuxO3−δ

The La(Mn_0.5Co_0.5)_1−xCu_xO_3−δ series with x=0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8 and 1 was synthesized by the Pechini method to obtain insight into the phase formation in the quasi-ternary LaMnO₃-LaCoO₃-“LaCuO₃” system caused by the instability of LaCuO₃ under ambient conditions. After sintering at 1100°C some remarkable results were obtained: LaMn_0.3Co_0.3Cu_0.4O_3−δ crystallized as a single phase in the orthorhombic perovskite structure typical of LaCuO₃. Among the synthesized compositions this compound showed the highest electrical conductivity in air at 800°C (155 S cm⁻¹) and also the highest thermal expansion coefficient (α_30−800°C=15.4×10⁻⁶ K⁻¹). The LaCuO_3−δ composition also crystallized as a single phase but in a monoclinic structure although previous investigations have shown that other phases are preferably formed after sintering at 1100°C. The electrical conductivity and thermal expansion coefficient were the lowest within the series of compositions, i.e. 9.4 S cm⁻¹ and 11.9×10⁻⁶ K⁻¹, respectively.     

Method development for the determination of cadmium in fertilizer samples using high-resolution continuum source graphite furnace atomic absorption spectrometry and slurry sampling

The determination of cadmium (Cd) in fertilizers is of major interest, as this element can cause growth problems in plants, and also affect animals and humans. High-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) with charge-coupled device (CCD) array detection overcomes several of the limitations encountered with conventional line source AAS, especially the problem of accurate background measurement and correction. In this work an analytical method has been developed to determine Cd in fertilizer samples by HR-CS GF AAS using slurry sampling. Both a mixture of 10 μg Pd + 6 μg Mg in solution and 400 μg of iridium as permanent modifier have been investigated and aqueous standards were used for calibration. Pyrolysis and atomization temperatures were 600 °C and 1600 °C for the Pd-Mg modifier, and 500 °C and 1600 °C for Ir, respectively. The results obtained for Cd in the certified reference material NIST SRM 695 (Trace Elements in Multi-Nutrient Fertilizer) of 16.7 ± 1.3 μg g⁻¹ and 16.4 ± 0.75 μg g⁻¹ for the Pd-Mg and Ir modifier, respectively, were statistically not different from the certified value of 16.9 ± 0.2 μg g⁻¹ on a 95% confidence level; however, the results obtained with the Ir modifier were significantly lower than those for the Pd-Mg modifier for most of the samples. The characteristic mass was 1.0 pg for the Pd-Mg modifier and 1.1 pg Cd for the Ir modifier, and the correlation coefficients (R²) of the calibration were > 0.99. The instrumental limits of detection were 7.5 and 7.9 ng g⁻¹, and the limits of quantification were 25 and 27 ng g⁻¹ for Pd-Mg and Ir, respectively, based on a sample mass of 5 mg. The cadmium concentration in the investigated samples was between 0.07 and 5.5 μg g⁻¹ Cd, and hence below the maximum value of 20 μg g⁻¹ Cd permitted by Brazilian legislation.