程序升温技术研究Mo/HZSM-5催化剂上甲烷无氧芳构化反应积炭的化学特性

对经过程序升温表面甲烷无氧芳构化反应(TPSR)后的Mo/HZSM-5催化剂上的积炭进行了程序升温加氢反应(TPH)和程序升温CO₂反应(TPCO₂),并对相应催化剂上的积炭进行了程序升温氧化反应(TPO)和热重(TG)实验.TPH实验及TPCO₂实验表明,H₂主要对高温烧炭峰发生作用.CO₂则可同时对这两种烧炭峰产生影响,对低温峰积炭的影响尤其明显.对不同Mo含量的催化剂进行上述实验的结果表明,Mo担载量的变化及不同的实验过程都会影响催化剂上两种温峰的积炭在总积炭量中所占的比例.由TG实验数据计算出的动力学结果说明,无论是TPH还是TPCO₂实验都可以降低烧炭过程的一级反应起始温度,并减少其活化能.此外,催化剂中Mo担载量的变化也会对开始温度和烧炭活化能产生明显影响.     

环戊烷和环己烷在silicalite-1分子筛上的热脱附行为

采用智能质量分析仪(IGA)及TG/DTG法研究了环戊烷和环己烷在硅沸石silicalite-1上的热脱附行为。当环戊烷在silicalite-1上吸附量小于4 m/uc时,TG/DTG曲线表明环戊烷在silicalite-1上存在一个脱附过程。吸附量大于4 m/uc,TG曲线显示热脱附过程明显分为两个阶段,DTG曲线中出现两个明显的脱附峰,彼此分离。环己烷在silicalite-1上只存在一种脱附过程,DTG曲线只出现一个脱附峰。从环戊烷和环己烷的热脱附曲线中也可看出,随着吸附量的增加脱附峰温逐渐向高温方向偏移。     

Matrix properties and composite failure

The influence of matrix extensibility on the properties of a composite was studied using two glassy polymers of almost identical chemical structure but differing crosslink densities. The lower crosslink density gave a 73 % increase in tensile elongation at break and a 56% increase in specific fracture energy. Unidirectional laminates of glass, carbon, and Kevlar^® fibres were prepared with these two polymers and tested for shear strength, transverse tension, and dynamic fatigue.The shear strengths of the polymers were found to be almost independent of crosslink densities (about 100 MPa). The interlaminar shear strengths of the carbon fibre laminates corresponded to those of the matrix polymers (Kevlar^® fibre laminates failed at 60 %). In accordance with Griffith's equation the more extensible polymer and its laminates performed better in tensile tests transverse to the fibres due to improved fracture energy. Failure criteria based on strain magnification were useful in the case of glass fibre laminates, but proved inadequate for laminates based on anisotropic fibres such as carbon and Kevlar^®.The dynamic fatigue strengths of the two matrix polymers were unaffected by the difference in crosslink densities. Almost the same fatigue strengths were obtained for the matrix polymers as for the laminates (carbon, glass) transverse to the fibres. A lack of processability of the polymer with high functionality was identified as a source of deteriorating effects.     

Thermal analysis of fibre forming polymers

Different levels of fibre technologies and application, from synthesis to degradation has been studied using the methods of thermal analysis. Recent results of these studies on synthetic and natural fibres are summarized. The effect of chemical and physical modification of polyolefin fibres as well as the synthesis of polymer emulsion used as additive in fibre technologies could be followed by DSC, DMA, TG methods.     

Cyclosilazanes and borazines: polymer precursors to silicon‐ and boron‐containing ceramics

The chemistry of cyclosilazanes and borazines is a topic of current interest in view of preceramic polymers which yield on pyrolysis various useful ceramic materials, e.g. silicon and boron carbide, silicon and boron nitride, and ternary or quaternary mixtures of these materials. These materials are hard and have high oxidative and thermal stability. Other useful properties are resistance to corrosion, thermal shock and creep, low electrical conductivity and low coefficient of thermal expansion. One of the best application prospects is the use of the preceramic polymers as protective coating material for carbon fibres. Copyright © 2000 John Wiley & Sons, Ltd.     

Synthesis and characterization of deuterated poly(arylene ether sulfones)

Selectively deuterated poly(arylene ether sulfones) were prepared for neutron scattering studies and for deuterium NMR investigations. The availability of these model macromolecules permits molecular-level identification of the motions responsible for the low temperature relaxations that have been observed in the dynamic mechanical spectra of these engineering polymers. Three labeled sites on the appropriate monomers (bisphenol-A and 4,4′-dichlorodiphenylsulfone) were prepared from deuterated intermediates and characterized via chromatographic, spectroscopic, and thermal analysis. The deuterium exhcange between methyl and aromatic sites that occurred during synthesis was quantified. These labeled monomers were mixed with hydrogenous monomers to synthesize high molecular weight, selectively deuterated poly(arylene ether sulfones). A synthetic technique involving N-methyl-2-pyrrolidone/potassium carbonate was employed to afford high molecular weight polymers. The polymers were characterized by FT-IR, proton, carbon, and deuterium NMR, intrinsic viscosities, and thermal analysis. Molecular weights of the labeled polymers were similar to unlabeled systems.     

Improvement of Fibre-Matrix-Adhesion of Natural Fibres by Chemical Treatment

Plastics, also called synthetic polymers, are playing an important role in daily living. To raise more applications it is necessary to modify known polymeric systems to reach improved materials/material systems. A possibility to create new optimised materials out of neat polymers is offered by compounding them with different filling material. Besides chemical modification of polymers, mixing, combining or use of different fillers, one possibility is given by the composite technique, whereas the combination of the polymeric matrix and the embedded reinforcement (e.g. fibre) are yielding in optimised materials adjusted to the required properties. Concerning the polymeric matrix, either thermoplastic or thermoset material can be used. In case of the reinforcement, either synthetic (carbon-, glass- or polymeric fibres) or natural fibres are introduced to composites. To obtain an appropriate adhesion of the matrix to the reinforcement system, synthetic fibres are equipped with an avivage. For natural fibres, there are no such materials available and the hydrophilic property of this system surface prevents an adhesion to hydrophobic polymers, as well as to sizings. In this paper, ways are shown to modify the natural fibres via chemical treatment to yield higher physical properties at better adhesion. Also we will explain activities on the use of natural fibres as reaction systems and processing tools as well as the attempt to isolate the different compounds of the neat fibre via selective work-up.     

Thermal degradation and decomposition of jute/vinylester composites

Thermal analysis of jute fibre reinforced vinylester resin with 30 vol% of fibre were performed by TG/DTG under dynamic conditions. The fibres were treated with alkaline solution at different temperatures and the final composition (cellulose, hemicellulose and lignin) of the fibre was determined by chemical analysis. Apparent activation energies were determined using a variety of conventional thermogravimetric methods. Two peaks were found in the composite differential curves: the first peak close to 327 and the second peak at 408°C. The apparent activation energy values for the second peak decreased when fibre were treated. The addition of the jute fibres produced a slightly decrease in the thermal stability of the composites.     

Two-dimensional liquid chromatography analysis of synthetic polymers using fast size exclusion chromatography at high column temperature

In recent years, two-dimensional liquid chromatography (2D-LC) has been used increasingly for the analysis of synthetic polymers. A 2D-LC analysis provides richer information than a single chromatography analysis at the cost of longer analysis time. The time required for a comprehensive 2D-LC analysis is essentially proportional to the analysis time of the second dimension separation. Many of 2D-LC analyses of synthetic polymers have employed size exclusion chromatography (SEC) for the second-dimension analysis due to the relatively short analysis time in addition to the wide use in the polymer analysis. Nonetheless, short SEC columns are often used for 2D-LC analyses to reduce the separation time, which inevitably deteriorates the resolution. In this study, we demonstrated that high temperature SEC can be employed as an efficient second-LC in the 2D-LC separation of synthetic polymers. By virtue of high temperature operation (low solvent viscosity and high diffusivity of the polymer molecules), a normal length SEC column can be used at high flow rate with little loss in resolution.     

Synthesis and thermal behaviour of polyamide 6/bentonite/ammonium polyphosphate composites

In order to achieve acceptable levels of flame retardancy of polymers, phosphorus-based flame retardant (FR) additives at about 20-30% w/w are required which is too high for conventional synthetic fibres. To know whether more finely sized particles of conventional FRs with or without nanoclay are more effective at the same concentration, composites of PA6 with bentonite and ammonium polyphosphate (APP) have been prepared by melt processing in a twin-screw extruder. XRD peaks and TEM images of PA6/Org-bentonite composite show partially ordered intercalation and ordered exfoliation. Thermal analysis in He shows that thermal stability of PA6 nanocomposite has increased by 18 °C compared with pure PA6 during degradation after 425 °C but it has decreased by 100 °C on inclusion of APP in PA6/nanoclay composites. The char yield is increased by 20% in PA6/bentonite/APP composites. No effect on thermal stability or char yield is observed by reducing the particle size of APP.     

Screening phosphatidylcholine biomarkers in mouse liver extracts from a hypercholesterolemia study using ESI-MS and chemometrics

When fed a high-fat, high-cholesterol diet (HFD), homozygous LDL receptor knockout mice exhibit extremely high levels of plasma cholesterol that are expected to influence liver metabolism. One step in the investigation of potential hepatic alterations was the analysis of organic extracts of livers from these and control mice by electrospray mass spectrometry (ESI-MS). Chemometrics (bioinformatics) analysis shows that the sample spectra cluster into two groups: one from mice with plasma cholesterol levels in excess of 900 mg dL⁻¹ and one from animals with cholesterol levels of 60–250 mg dL⁻¹. The loadings plot of the first PC in the principal-components analysis (PCA) reveals the chemical basis for clustering, i.e., biomarkers present at different concentrations in the different groups. The exact masses of the key peaks in this loadings plot indicate these species are phosphatidylcholines (PtdChos). This assignment is confirmed by tandem MS. Partial least-squares (PLS) with variable selection shows that the spectra are well correlated with plasma total cholesterol, HDL cholesterol, and triglyceride (TG) levels.     

Study of radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. III. Effect of p-benzoquinone and ammonia on radiation-induced polymerization of styrene adsorbed on silica gel

In order to elucidate the mechanism of radiation-induced polymerization of styrene adsorbed on silica gel, the effect of p-benzoquinone and ammonia was investigated. The high molecular weight GPC peaks of both graft polymers and homopolymers decreased with increasing p-benzoquinone concentration, while the low molecular weight peaks of both graft copolymers and homopolymers decreased with increasing ammonia concentration. The results indicate that the high molecular weight peaks of both graft and homopolymers are formed as a result of a radical mechanism and that the low molecular weight peaks of both types of polymers are formed by a cationic mechanism. In formation of both graft polymers and homopolymers both radical and cationic polymerization take place at the same time.     

PLASMA POLYMERIZATION OF HEXAMETHYLCYCLOTRISILOXANE

In a capacitively coupled RF discharge system with external electrodes ,hexamethyicyclotrisiloxane was polymerized, and the effects of discharge power and plasma gas on polymer deposition rate were studied. The polymer structures and properties were studied by IR spectroscopy, XPS measurement, PGC/MS combined technique, TG analysis and contact angle measuring. The results showed that the polymers prepared in H_2 or O_2 have higher C/Si ratio in comparison with those prepared in inert gases. PGC/MS results revealed the existence of many short carbon chains in the polymer structure .TG analysis suggested that the polymers prepared in the inert gas would possess better thermal stabilities.     

Date palm fibre filled recycled ternary polymer blend composites with enhanced flame retardancy

Flammability of recycled polypropylene (PP)/low density polyethylene (LDPE)/high density polyethylene (HDPE) ternary blends containing date palm fibres is investigated in this study. Melt blending is used for the composite preparation and the palm fibres induce good mechanical strength to the blend composites. The effect of flame retardant magnesium hydroxide, is studied through the limiting oxygen index analysis and cone calorimeter studies. Morphology of the palm fibres in presence of fire retardant reveals interesting facts of base hydrolysis. Since the polymers used are recycled ones and the fibres are obtained from the date palm leaves, the whole composite manufactured stands as low cost, less energy consuming and environmental friendly. Though the flame retardant reduced the mechanical properties, the palm fibres strengthened the whole composite thus helping to achieve the flame retardancy and mechanical properties simultaneously. Flame retardancy is correlated with the thermal degradation and thermal conductivity of the blend fibre composites as well.     

Study of radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. IX. Preirradiation polymerization of styrene–silica gel system

Preirradiation polymerization of the styrene–silica gel system was studied in detail. Both graft polymers and homopolymers have bimodal GPC spectra. High molecular weight peaks were formed in a radical mechanism and the low molecular weight peaks were formed in a cationic mechanism as same as those in the simultaneous irradiation polymerization. The rate of formation of the low molecular weight peaks was very high compared with that of the high molecular weight peaks. Monomer conversion and percent grafting leveled off at about 1–2 Mrad. Radiation dose dependence of the four peaks were different from each other. Monomer conversion and percent grafting decreased as the preheating temperature of silica gel increased. The amount of the low molecular weight peaks of graft polymers depended on the number of silanol groups, as in the case of the simultaneous irradiation polymerization. A reaction mechanism for the preirradiation polymerization is proposed based on the results obtained.     

Study of radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. V. Effects of p-benzoquinone and dose rate on methyl methacrylate–silica gel system

In order to elucidate the mechanism of radiation-induced polymerization of methyl methacrylate adsorbed on silica gel, the effects of p-benzoquinone addition and dose rate were studied in detail. Most of the polymerization is inhibited by p-benzoquinone at levels above 10^-2 mole/l. The GPC spectra of both graft polymers and homopolymers show two peaks. The high molecular weight material appears to have been formed by polymerization by a radical mechanism, because these peaks decrease as p-benzoquinone concentration increases; on the other hand, their low molecular weight polymers seem to be products of an ionic polymerization mechanism because those peaks are almost not affected by p-benzoquinone. The four GPC peaks differ in dose rate dependences of their polymerization rate. The dose-rate exponents of polymerization rate were obtained for the four GPC peaks. The behavior of the low molecular weight peaks of graft polymers and homopolymers were quite different, suggesting that the polymers differ considerably in formation mechanism.     

Structure-property relations in linear and crosslinked liquid crystalline polymers

This paper reviews structure-property relations in liquid crystalline side group polymers, as investigated by X-ray scattering of fibres, by small angle X-ray scattering in solution, by dielectric relaxation measurements and by melt rheology, as well as synthetic ways to “combined liquid crystalline polymers”. The synthesis of liquid crystalline elastomers from side group, main chain and combined liquid crystalline polymers is described. First structure-property relations are discussed.     

Cobalt‐catalyzed alternating and nonalternating copolymerization of carbon monoxide with aziridine

Catalysts CH₃COCo(CO)₃PPh₃ ( 1 ) and HCo(CO)₃PPh₃ ( 2 ) catalyze the copolymerization of aziridine and carbon monoxide. Catalyst 2 can be conveniently generated in situ via reaction of Na⁺Co(CO)₄, N,N‐dimethylanilinium chloride, and PPh₃. The copolymerization alternates at high catalyst loadings to produce poly(β‐alanine). The end groups of the poly(β‐alanine) product are characterized by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry and by comparison of the ¹H NMR spectra of the polymer and a stepwise synthesized model compound. At low catalyst loadings, the polymer product contains both the β‐alanine units and amine units because of nonalternating enchainment of the comonomers. The characterization of the amine units is again supported by comparison of the ¹H NMR spectra of the polymers and the stepwise synthesized model compounds. The molecular weights of the polymers are determined by gel permeation chromatography. The thermal stability of the polymers is probed by differential scanning calorimetry and thermogravimetric analysis. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 376–385, 2003     

Hidden information in principal component analysis of ToF‐SIMS data: On the use of correlation loadings for the identification of significant signals and structure elucidation

In this paper, an improved approach to interpret results of principal component analysis (PCA) of time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) spectra is presented. Signals are typically observed in different intensity ranges in a single ToF‐SIMS spectrum due to different sensitivity factors and surface concentrations. This can complicate the PCA interpretation, because loadings are reported to be strongly affected by these intensity changes. In contrast, it is shown here that correlation loadings are unaffected by these differences. In particular, correlation loadings were successfully used to identify signals with relatively low intensity but high significance. These signals may be overlooked when only loadings are used. This is particularly true in failure analysis, where ToF‐SIMS is used to screen for initially unknown signals that may be relevant for the characteristics/failure of a product. As a model study, the concept was applied to investigate ageing of Li‐ion batteries by ToF‐SIMS. In this data set, the significance of impurities that affect the quality of Li‐ion batteries was identified only by correlation loadings, whereas the loadings were found to overestimate the influence of other matrix signals. In addition, correlation loadings aid in the chemical identification and helped to successfully assign unknown peaks.     

IFSS, TG, FT-IR spectra of impregnated sugar palm (Arenga pinnata) fibres and mechanical properties of their composites

This study aimed to investigate the effect of resin impregnation on the interfacial shear strength (IFSS), thermogravimetric (TG) and fourier transform infrared (FT-IR) of sugar palm (Arenga pinnata) fibres. In addition, the effect of resin impregnation on the mechanical properties of sugar palm fibre reinforced unsaturated polyester (UP) composites was also studied. The fibres were impregnated with UP via vacuum resin impregnation process at a pressure of 600 mmHg for 5 min. Composites of 10, 20, 30, 40 and 50 % fibre loadings were fabricated and tested for tensile and flexural properties. It was observed that the impregnation process caused the fibres to be enclosed by UP resin and this gave a strong influence to the increase of its interfacial bonding by the increase of its IFSS from single fibre pull-out test. It was also observed with TG and FT-IR spectra that the impregnated fibre had lower moisture uptake than the control and there was no significant increase in thermal stability of the impregnated fibre. The sequence of fibre decomposition started from the evaporation of moisture, hemicelluloses, cellulose, lignin and finally ash content and the presence of these components were proven by FT-IR spectra. For the composite specimens, due to the high interfacial bonding of the impregnated fibre and the matrix, the impregnated composites showed consistently higher tensile strength, tensile modulus, elongation at break, flexural strength, flexural modulus and toughness than the control samples. It was also observed that 30 % fibre loading gave optimum properties.