Dithiothreitol-based polyurethanes. Synthesis and degradation studies

The synthesis, characterization, and some properties of new copolyurethanes are described. These copolyurethanes were obtained by reaction of 1,4-di-S-benzyl-d,l-dithiothreitol (DTTSBn) and triethylene glycol (TEG) with 1,6-hexamethylene diisocyanate (HMDI). The copolymer compositions were studied by ¹H NMR, revealing that the content of the copolymer units is in good agreement with that of their corresponding feed. The PU(TEG-HMDI) homopolymer exhibited a high crystallinity, but the introduction of the DTTSBn diol led to a reduction in the crystallinity of the copolymers and an increase of the stiffness, with associated increases in the T_g values. In their TG curves, the copolymers exhibited a mixed trend of the related homopolymers; all of them were thermally stable, with degradation temperatures above 250 °C and with higher thermal resistance displayed by the polymers with higher TEG contents. The chemical and enzymatically catalyzed hydrolytic degradations of the macromolecules were tested. PU(TEG-HMDI) was the only polymer degraded under physiological conditions, but an increase of temperature markedly affected the degradation rates. Two proteolytic enzymes (papain and α-chymotrypsin) and two esterase enzymes (cholesterol esterase and lipase) were chosen to perform enzyme-mediated hydrolysis trials, the first reported use of pancreatic lipase for urethane-bond hydrolysis in polyurethanes.     

The reciprocal influence between ion transport and degradation of PA66 in acid solution

Transport behavior of acid solution through polyamide was studied by measuring element distribution in cross section, pH, and ion concentration. Degree of degradation that related to the decreasing of molecular weight and flexural strength was observed in order to study the influence of acid solution on the polyamide 66 (PA66) degradation. The permeation mechanism of acid solution can be explained: at first water penetrates into polyamide and it is followed by acid. In this process, water does not affect the molecular weight at 50 °C but only reduces the polyamide strength by plasticization. Moreover, proton (H⁺) has contributed to the anion transport and degradation of polyamide by the hydrolytic reaction. Proton attacks the polyamide chain, and scission of chain occurs, and reacts with anion to form other material substance. This process affects the decrease of molecular weight and the significant loss of polyamide strength. Analysis results from ion concentration measurement shows that the amount of proton and anion transport into deionized waterside was imbalance, which probably due to the different mobility between proton and anion or formation of other material substance by reaction of anion and PA66 bond. Such information is not only necessary for the investigation of hydrolytic degradation of polymer and prediction of lifetimes for a protective polymer lining/coating to chemical attack, but may also be helpful towards gaining a deeper insight into the processes of degradation of other polymer.     

New confined p-phenylenevinylene (PPV)-type polymer analogue of poly(phenylene sulfide)

A new confined p-phenylenevinylene (PPV)-type polymer (PPVS) has been synthesized using Wittig condensation. The chemical structure of the polymer was well defined by ¹H NMR, ¹³C NMR, and FTIR spectroscopic analysis. PPVS contains oligomeric PPV units separated by sulfide bridges in the main chain; it is fully soluble in common organic solvents and has a number-average molecular weight of 3500 g mol⁻¹. Thermogravimetric analysis and differential scanning calorimetry indicate that PPVS is amorphous, stable up to 360 °C in air and displays a glass transition temperature of 98 °C. The optical properties of the polymer were investigated by UV-visible absorption and photoluminescence spectroscopies. The polymer film absorbs at 375 nm and emits at 517 nm with a narrow emission spectrum. From the cyclic voltammetry analysis, the electrochemical bandgap was estimated to be 2.78 eV. A single-layer diode device of the configuration indium-tin oxide/PPVS/aluminium has been fabricated and has a relatively low turn-on voltage of 3.4 V. An electroluminescent emission similar to photoluminescence is demonstrated in a multilayer device.     

Synthesis and hydrolytic degradation of poly(ethylene succinate) and poly(ethylene terephthalate) copolymers

The conditions of synthesis of statistical poly(ethylene succinate-co-terephthalate) copolymers (2GTS) and high molecular weight poly(ethylene succinate) (PES) with good hydrolytic and optical parameters, designed for the production of biodegradable products and resins, are presented in this article. Copolymers were prepared by melt polycondensation of bis-(β-hydroxyethylene terephthalate) (BHET) and succinic acid (SA) with excess of ethylene glycol (2G) in the presence of a novel titanium/silicate catalyst (C-94) and catalytic grade of germanium dioxide (GeO₂) as cocatalyst. The chemical structure and physical properties of those materials were characterized by ¹H NMR, FT-IR, dynamical-mechanical thermal analyses (DMTA), differential scanning calorimetry (DSC), solution viscosity and spectroscopic methods. The hydrolytic degradation was performed in a water solution with variable pH, also in garden soil and in compost. The highest hydrolytic degradation rate was observed for pH 4 and for compost. Better hydrolytic degradation values in compost medium were observed for copolyester prepared in the presence of GeO₂ as polycondensation cocatalyst. The copolyester with 40 mol% of aliphatic units was chosen for industrial syntheses which were performed in ELANA and subsequently the processing parameters and compatibility with potato starch of this polyester were checked by BIOP Biopolymer Technologies AG.     

The phases of polymers as determined by NMR

Nuclear magnetic resonance (NMR) spectroscopy has been used to study the morphology and dynamics in semicrystalline polymers. Dynamics may be observed through NMR relaxation rates that are sensitive to motions in the 1–10⁸ Hz range, or through modulation of anisotropic magnetic interactions, such as the chemical shift and dipole-dipole interactions. Morphological structure may be inferred through NMR measurements of polymer dynamics or investigated directly through studies of the magnetic interactions. Here, we discuss the study of morphological structure in semicrystalline polymers using NMR, and review results on poly(ethylene terephthalate) that address the question of the number of phases in this semicrystalline polymer.This work was funded by the Office of Naval Research.     

Preparation, characterization and hydrolytic degradation of poly[p-dioxanone-(butylene succinate)] multiblockcopolymer

A series of poly[p-dioxanone-(butylene succinate)] (PPDOBS) copolymers were prepared from p-dioxanone (PDO), 1,4-butanediol and succinate acids through a two-step process including the initial prepolymer preparation of poly(p-dioxanone)diol (PPDO-OH) and poly(butylene succinate)diol (PBS-OH) and the following copolymerization of the two kinds of prepolymers by coupling with hexamethylene diisocyanate (HDI). The molecular structures of the prepared PPDO-OH, PBS-OH and PPDOBS were characterized by hydrogen nuclear magnetic resonance spectroscopy (¹H NMR). The crystallization of the copolymers was investigated by using differential scanning calorimetry (DSC), polarized optical microscopy (POM) and wide angle X-ray diffraction (WAXD). It has been shown that the crystallization rate and the degree of crystallization increases with the increase of the weight fraction of poly(butylene succinate) (PBS) blocks in the copolymers. In phosphate buffer solution with pH 7.4 at 37 °C for 18 weeks, the hydrolytic degradation behaviors of the copolymers were studied. The changes of retention weight, water absorption, pH value, and surface morphologies with the degradation time showed that the hydrolytic degradation rate of PPDOBS could be controlled by adjusting the weight fraction of poly(p-dioxanone) (PPDO) and PBS blocks in the copolymers. The changes of the thermal properties of PPDOBS during the degradation were also investigated by DSC.     

Hydrolytic degradation and thermooxidative stability of polyimides based on 3,5-diaminodiphenyl oxide and 2-methyl-3,5-diaminodiphenyl sulfide

For a number of new polyimides prepared from 3,5-diaminodiphenyl oxide, 2-methyl-3,5-diaminodiphenyl sulfide, and various dianhydrides of aromatic tetracarboxylic acids, the hydrolytic stability in DMF and 96% H₂SO₄ and the thermooxidative stability in the bulk have been studied. Hydrodynamic techniques have been employed to determine the molecular parameters of these polymers at various stages of degradation. It has been shown that the polymers under study form stable solutions in DMF but turn out to be unstable in 96% H₂SO₄ even at room temperature. Degradation accompanies dissolution of the polymer. The correlation between the chemical structure of polymer molecules and their hydrolytic stability in both solvents has been established. It has been demonstrated that the majority of the said polyimides are stable in the solid state at temperatures up to 400°C and marked degradation begins only above 500°C.     

Hygrothermal aging of Nafion

The membrane durability is a critical issue for the development of Proton Exchange Membrane Fuel Cells (PEMFC). Since PEMFC in situ tests were not conclusive to determine Nafion^® membrane degradation mechanism, ex situ aging tests were performed on Nafion^® 112 in practical fuel cell usage conditions. The polymer chemical structure evolution was investigated by infrared spectroscopy (IR) and Nuclear Magnetic Resonance (NMR) while its hydrophilicity, directly linked to its protonic conductivity, is established through sorption isotherms by Dynamical Vapour Sorption (DVS). Durability studies over a period of 400 days revealed membrane degradation through a modification of sulfonic acid end-groups. Formation of sulfonic anhydride (from the condensation of sulfonic acids) was strongly demonstrated by IR spectroscopy and, indirectly, by NMR. The substitution of ionic end-groups by less hydrophilic anhydrides leads to a significant decrease of water uptake and thus of its hydrophilicity. Surprisingly, kinetic study reveals that the hygrometric level accelerates this condensation reaction.     

Hydrolytic degradation of carbohydrate-based aromatic homo- and co-polyesters analogous to PET and PEI

The hydrolytic degradation of a series of homo- and co-polyesters analogous to poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), prepared from carbohydrate-based monomers, was studied. The degradation process was carried out at temperatures of approximately 10 °C above the T_g of the polymers. All the studied polyesters were found to degrade at significant rates, and degradability showed a clear dependence on the configuration of the sugar units present in the polymer chain. No weight loss was detected upon degradation, apparently due to the non-solubility of the degraded products in the aqueous incubation medium. Hydrolysis of co-polyesters took place preferentially by cleavage of the ester groups of the sugar units.     

s-Triazine containing flame retardant hyperbranched polyamines: Synthesis, characterization and properties evaluation

A s-triazine containing hyperbranched polyamine (HBPA) has been synthesized from cyanuric chloride and aromatic diamine, 4,4′-(1,4-phenylenediisopropylidene) bis-aniline by nucleophilic displacement polymerization technique using an A₂ + B₃ approach with high yield (>80%). The synthesized polymer has been characterized by ¹H NMR, ¹³C NMR, FT-IR spectroscopic studies, elemental analysis, solubility and measurement of solution viscosity. The thermogravimetric (TG) analysis and differential scanning calorimetric (DSC) studies indicate that the polymer is thermostable upto 290 °C without any decomposition and has glass transition temperature of 243 °C. The flame retardancy of the pure powder polymer and the blends with linear commercial polymers such as plasticized PVC and LDPE with this hyperbranched polymer were investigated by the measurement of limiting oxygen index (LOI) value. The results show that the polymer has self-extinguishing characteristic (LOI = 38) and acts as an effective flame retardant additive for the above linear base polymers. The synergistic effect of this hyperbranched flame retardant was observed with triphenyl phosphine oxide in the same base polymers. The flammability efficiency of the hyperbranched polyamine is also evaluated by help of thermogravimetric (TG) analysis. The heat aging and leaching in different chemical media did not influence the flame retardancy of the blends.     

Chemical degradation of poly(2-aminoethyl methacrylate)

Poly(2-aminoethyl methacrylate) (PAMA) has a pK_a of approximately 7.6 and is chemically stable in acidic or neutral aqueous solution in its protonated form. However, chemical degradation of PAMA is known to occur in alkaline media as its primary amine groups become deprotonated (He L et al. Macromolecules 2007; 40: 4429-38). In the present work, the effect of temperature, pH and polymer concentration on the rate of PAMA degradation in dilute aqueous solution has been examined. ¹H NMR spectroscopy indicates that both elimination of 2-aminoethanol and formation of 2-hydroxyethyl methacrylamide repeat units occur above pH 9; elimination is observed first and occurs to a greater extent. FT-IR studies of aqueous PAMA solutions aged at pH 12 and 50 °C confirm the presence of anionic carboxylate groups, which suggests that such elimination is simply due to ester hydrolysis. A control experiment suggests that methacrylamide formation occurs via internal rearrangement, rather than by amidation of the remaining ester groups by the eliminated 2-aminoethanol.     

Photochemical isomerization of norbornadiene‐containing polytriazoles obtained by click chemistry polyaddition

Polyesters and polyethers containing norbornadiene (NBD) and 1,2,3‐triazole units in the main chain are prepared by step growth polymerization of diester or diether NBD‐based dialkynes with different aromatic diazides using copper‐catalyzed azide–alkyne cycloaddition. The solubility and the physical properties of the resulting polytriazoles are investigated by differential scanning calorimetry, thermogravimetric analysis, size exclusion chromatography, and ¹H NMR spectroscopy, and are discussed taking into account of the chemical structures of the monomers. All of them are amorphous with glass transition temperatures ranging from 51 to 117 °C, number average molecular weight (M_n) values from 16 to 43 kDa and thermal degradation (T_d10) values from 175 to 292 °C. The photochemical valence isomerization (PVI) of the NBD units into quadricyclanes (QC) is investigated using UV–vis spectroscopy of polymer films spin‐coated onto quartz substrates. For the first time the PVI of NBD into QC is demonstrated by ¹H NMR spectroscopy. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 223–231     

Synthesis and modification of polysilylcarbodiimides

Conditions for the synthesis of linear polysilylcarbodiimides based on bis(trimethylsilyl)carbodiimide have been investigated. The method of preparing new silylcarbodiimidesilazane polymers via the polycondensation of bis(trimethylsilyl)carbodiimide with methylphenyldichlorosilane and cyclosilazanes has been developed. The highest molecular mass of the polymers achieves 10 000, as evidenced by GPC measurements. The structure of polysilylcarbodiimidesilazanes has been examined by IR spectroscopy and ¹H NMR studies. Silazane units are incorporated into polymer chains as linear and stressed cyclodisilazane fragments. TGA experiments have revealed that silazane fragments reduce weight losses of the new polymers in the course of thermal degradation.     

Novel polyesteramide-based di- and triblock copolymers: From thermo-mechanical properties to hydrolytic degradation

Two types of biodegradable poly(ε-caprolactone (CLo))-co-poly(ε-caprolactam (CLa)) copolymers were prepared by catalyzed hydrolytic ring-opening polymerization. For the first type of materials, the respective cyclic comonomers were added simultaneously in the reaction medium leading to the formation of copolymers having a random distribution of co-units within the polyesteramide sequence, as evidenced by ¹H and ¹³C NMR. For the second type of copolymers, the cyclic comonomers were added sequentially in the reaction medium yielding diblock polyesteramides, again evidenced by NMR. The thermal and thermo-mechanical properties of the copolymers were investigated by DSC and DMA and correlated with the copolymer topology and composition. The copolymers were characterized by a storage modulus and α transition temperature intermediate to the modulus and T_g of the corresponding homopolymers. The chemical composition and molecular weight of the copolymers proved to have only a limited effect on the thermo-mechanical properties of the materials. The hydrolytic degradation of random copolymers was studied in a phosphate buffer at 60 °C and discussed in terms of chemical composition and molecular weight of the copolymers.     

Initial steps of thermal degradation of PVC prepared at various temperatures

PVC samples were obtained by bulk polymerization initiated with AIBN and ultraviolet irradiation at 40, 25, 0, ?30, and ?50°C. They were characterized by ¹³C NMR measurements, infrared spectroscopy, GPC in hexamethylphosphoramide and B.E.T. surface area measurements. Their thermal degradation was studied between 110 and 185°C by using continuous titration of HCl evolved through a conductimetric cell. The ultraviolet spectra were recorded at various steps of the degradation. At high degradation temperatures, the more syndiotactic the polymer, the longer the polyene average sequences are. The amount of HCl evolved is minimum for a polymerization temperature of 0 or 25°C, depending on the degradation temperature and on the morphology of the polymer. The results are discussed in terms of chemical factors (tacticity distribution, molecular weight) as well as of physical factors (morphology, interval viscosity).     

Characterisation of regioselectively functionalized 2,3-O-carboxymethyl cellulose by enzymatic and chemical methods

The determination of the molecular structure of 2,3-O-carboxymethyl cellulose (2,3-O-CMC), prepared via 6-O-(4-monomethoxy)triphenylmethyl cellulose, was carried out in detail by means of enzymatic and chemical methods. The 2,3-O-CMCs had degrees of substitution (DS) in the range of 0.5–1.2 showing a narrow molar mass distribution as revealed by SEC. As a result of an endoglucanase treatment, an intensive depolymerization of the samples occurred which was more pronounced for 2,3-O-CMC with comparatively low DS. All degraded samples could be separated into 18 fractions by preparative SEC and the proportion of each individual repeat unit was analysed by anion exchange chromatography (AEC) following complete hydrolytic chain degradation. The results indicated a homogeneous distribution of the functional groups within the polymer chain. Moreover, it became obvious that a preferred carboxymethylation of O-2 compared with O-3 occurred and that a preferred functionalization of already carboxymethylated units occurred as the reaction progressed. AEC with pulsed amperometric detection, which was used to separate and analyse the differently functionalized repeating units as well as glucose, had to be calibrated. Therefore, a method to determine the response factors of the individual carboxymethylated glucose units was developed using ¹³C NMR spectroscopic measurements (inverse gated decoupling) of depolymerised 2,3-O-CMC.     

Synthesis of polymers containing regularly distributed tetrathia‐[7]‐elicene units along the backbone

A tetrathia‐[7]‐helicene bearing in the 2 and 13 positions cyanovinyl groups was used as comonomer in the Michael‐type polyaddition reaction with N,N′‐bis(β‐mercaptoethyl)piperazine. This led to a new polymer bearing tetrathia‐[7]‐helicene units regularly distributed along the polymer backbone, which may be regarded as the first example of a new family of potentially useful nonlinear optical materials. All products were structurally characterized by ¹H and ¹³C NMR spectroscopy. Differential scanning calorimetry characterizations revealed the presence, in both monomeric and polymeric helicenes, of glass‐transition like temperatures, associated to some conformational variation of the helicene units. The optical properties, the film formation and the morphology of the polymer‐containing tetratia‐[7]‐helicenes were also investigated. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Mechanochemical generation of acid-degradable poly(enol ether)s

In an effort to develop polymers that can undergo extensive backbone degradation in response to mechanical stress, we report a polymer system that is hydrolytically stable but unmasks easily hydrolysable enol ether backbone linkages when force is applied. These polymers were synthesized by ring-opening metathesis polymerization (ROMP) of a novel mechanophore monomer consisting of cyclic ether fused bicyclohexene. Hydrogenation of the resulting polymers led to significantly enhanced thermal stability (T_d > 400 °C) and excellent resistance toward acidic or basic conditions. Solution ultrasonication of the polymers resulted in up to 65% activation of the mechanophore units and conversion to backbone enol ether linkages, which then allowed facile degradation of the polymers to generate small molecule or oligomeric species under mildly acidic conditions. We also achieved solid-state mechano-activation and polymer degradation via grinding the solid polymer. Force-induced hydrolytic polymer degradability can enable materials that are stable under force-free conditions but readily degrade under stress. Facile degradation of mechanically activated polymechanophores also facilitates the analysis of mechanochemical products.

A mechanically responsive polymer system that is hydrolytically stable without stress, but unmasks enol ether backbone linkages under force to allow facile hydrolytic degradation.     

23Na NMR in urethane cross-linked polyether solid polymer electrolytes

Sodium triflate/polyether urethane polymer electrolytes ranging in concentration from 0.05 molal to 1.75 molal have been investigated via ²³Na static solid-state NMR. Room temperature spectra and spin lattice relaxation times were consistent with a single narrow resonance indicating the presence of only mobile ionic species. The concentration and temperature dependence of relaxation times, chemical shifts, and linewidth have been investigated. The results suggest either a single species or rapid exchange between a number of species (even at temperatures below the glass transition temperature, T_g). The linewidth decreases with increasing concentration of ions and remains temperature independent below T_g. Below T_g a maximum quadrupolar interaction constant of 2 MHz is calculated. The addition of plasticizer to the polymer electrolyte causes significant chemical shift changes that depend on the solvent donicity of the plasticizer. The linewidth and T₁ relaxation times also depend on the T_g of the plasticized systems. Previous ²³Na NMR literature results are reviewed and qualitative models developed to account for the variation in results. © 1994 John Wiley & Sons, Inc.     

A novel hyperbranched copolymer constituted of triphenylamine and divinyl bipyridyl units

A hyperbranched copolymer (HTP) containing triphenylamine and divinyl bipyridyl units has been synthesized via Heck coupling reaction from 5,5′-divinyl-2,2′-bipyridyl and tris(4-bromophenyl)amine. The polymer had a number-average molecular weight of 1895 and a weight-average molecular weight of 2315, and was readily soluble in common organic solvents, such as THF, DMF and chloroform. The chemical structure of HTP was confirmed by FT-IR, ¹H NMR. Its thermal, electrochemical and optical properties have been investigated. The thermal analysis revealed that the polymer had a good thermal stability with the onset decomposition temperature at ca. 267 °C. The Uv-vis absorption and photoluminescence (PL) spectra exhibited that the Stokes shift between the absorption and emission of HTP was relatively large: 103 for HTP solution and 135 nm for HTP film. The electrochemical analysis showed that the electrochemical band gap of HTP was 0.92 eV. The fluorescence of the polymer in solution can be quenched by various transition metal ions and HTP showed different sensitivity in transition metal ions sensing.