Pd-Ag/PTFE复合膜的制备及表征

本文以不同孔径的聚四氟乙烯（PTFE）为基膜，采用化学镀法分别将Ag、Pd沉积到PIFE膜孔及膜面上，制得了镀层均匀、结合力较好的Pd-Ag／PTEE复合膜，并考察了PTFE基膜孔径对镀层结合力的影响，以及化学镀工艺对金属钯沉积速率、复合膜孔结构和截面电阻率的影响。结果表明，适当的基膜孔结构有利于提高镀层结合力；PTFE膜经化学镀修饰后，孔径减小，孔径分布变窄，孔隙率降低，膜截面电阻率降低10^6数量级，且孔径减小顺序与截面电阻率减小顺序一致。     

Preparation and characterization of polyaniline/polysulfone nanocomposite ultrafiltration membrane

Novel nanocomposite membrane was prepared through the filtration of polyaniline (PANI) nanofiber aqueous dispersion with polysulfone (PS) ultrafiltration (UF) membrane. Scanning electron microscope (SEM) images showed that PANI nanofiber layer was formed on the PS membrane surface. Atomic force microscopy (AFM) analysis indicated that the nanocomposite membrane had rougher surface than the PS substrate membrane. Compared with the PS substrate membrane, the nanocomposite membrane had much better permeability for the good hydrophilicity of PANI nanofiber layer, and had almost the same rejection performance. In addition, the nanocomposite membrane had positive surface potential under acidic condition because PANI could be protonated easily by acid. During the filtration of BSA solution, the nanocomposite membrane showed much better antifouling performance than the substrate membrane for the hydrophilicity and steric hindrance effect of its nanofiber layer. Moreover, under acidic solution condition, strong electrostatic repulsion between PANI nanofibers and BSA existed and improved membrane antifouling performance further.     

Preparation and characterization of antimicrobial polycarbonate nanofibrous membrane

Electrospinning of polycarbonate (PC)/chloroform solution with quaternary ammonium salt (benzyl triethylammonium chloride, BTEAC) was investigated to develop antimicrobial nanofibrous membranes for ultrafiltration. With BTEAC additive, ultrafine PC fibers were continuously generated and densely mounted without the blockage of spinning tip on electrospinning. When small amounts of BTEAC were added to the PC solution, the average diameter was also decreased from several micrometers to submicron range. It was found that the conductivity of the PC solution was a major parameter affecting the morphology and diameter of the electrospun PC fibers as well as the electrospinnability of PC. The nanofibrous membranes electrospun from the PC solution with BTEAC exhibited better excellent antimicrobial activity than those prepared without BTEAC. The PC nanofibrous filter shows a good filtration efficiency to satisfy the criterion of HEPA filter, and the pressure drop of the PC filters are within the normal range. Therefore, PC nanofibrous membrane showed a great potential as a candidate for ultrafiltration, compared to a commercial HEPA filter.     

Preparation and characterization of Pd-Ag alloy composite membrane with magnetron sputtering

A Pd-Ag (24 wt%) alloy composite membrane was prepared by the magnetron sputtering. A γ-Al_2O_3 membrane was synthesized by the sol-gel method and used as substrate of the Pd-Ag alloy film. The process parameters of the magnetron sputtering were optimized as a function of the compactness of the Pd-Ag alloy film. The best membrane with a thickness of 1 μm was produced with a sputtering pressure of 2.7 Pa and a substrate temperature of 400℃. The membrane had an H_2/N_2 permselectivity of 51.5--1000 and an H_2 permeation rate of 0.036--1.17×10~(-5)cm~3/cm~2·s· Pa, depending on operating conditions.     

Preparation and characterization of stable chitosan nanofibrous membrane for lipase immobilization

Nanofibrous membrane with a fiber diameter of 80-150 nm was fabricated from mixed chitosan/poly(vinyl alcohol) (PVA) solution by an electrospinning process. Field emission scanning electron microscope and transmission electron microscope were used to characterize the morphology of the nanofibrous membrane. It was found that chitosan nanofibrous membrane with stabilized morphology could be prepared through removing most of PVA from the nascent one with 0.5 M NaOH aqueous solution. This treatment also resulted in an obvious decrease in fiber diameter. The stabilized chitosan nanofibrous membrane was explored as support for enzyme immobilization due to the characteristics of excellent biocompatibility, high surface/volume ratio, and large porosity. Lipase from Candida rugosa was immobilized on the nanofibrous membrane using glutaraldehyde (GA) as coupling reagent. The properties of the immobilized lipase were assayed and compared with the free one. Results showed that, the observed lipase loading on this nanofibrous membrane was up to 63.6 mg/g and the activity retention of the immobilized lipase was 49.8% under the optimum condition. The pH and thermal stabilities of lipase were improved after it was immobilized on the chitosan nanofibrous membrane. In addition, the experimental results of reusability and storage stability indicated that the residual activities of the immobilized lipase were 46% after 10 cycles and 56.2% after 30 days, which were obviously higher than that of the free one.     

基于Ag/AgCl丝双涂膜司帕沙星选择电极的研制与应用

以Ag/AgCl丝为基体依次外涂含0.1 mol/L KCl的琼脂凝胶膜及含四苯硼-司帕沙星缔合物的PVC膜,制备了一种双涂膜司帕沙星选择电极。采用正交设计法,研究了离子缔合物的种类、活性物在膜中的浓度及增塑剂三因素对电极的影响。电极的线性范围为1.0×10-5~1.0×10-3mol/L,检出限为2.4×10-6mol/L,斜率为28.8 mV/decade(16℃),可直接用于司帕沙星片剂的含量测定,回收率为99.6%~101.1%,结果与文献法一致。     

Preparation,characterization, and performance of a novel hollow fiber nanofiltration membrane

Nanofiltration (NF) grade hollow fiber membrane was prepared by incorporation of zinc chloride into polysulfone–polyethylene glycol (molecular weight 200) blend. A 1.0 wt% zinc chloride in the blend reduced the molecular weight cut off (MWCO) of hollow fibers from 44 kDa (average pore size 64A⁰) to a nanofiltration range of MWCO 870 Da (average pore size 7.69 A^°). MWCO decreased further to 330 Da (average pore size 4.78 A^°) on addition of 2.5 wt% zinc chloride. types of NF hollow fiber were spun, corresponding to zinc chloride concentration of 1.0, 1.5, 2.0, and 2.5 wt%. Ternary phase diagram qualitatively explained the denser morphology for various concentrations of zinc chloride. This was supported by scanning electron micrographs of cross‐section and top surface of hollow fibers. NF membranes possessed negative surface charge at extreme pH conditions. Rejection of 1000 mg/l sodium chloride solution was in between 38 to 45% at pH 11, and for divalent sodium sulfate, it was in the range of 55 to 62%. Rejection of dye congo red was found to be 100%. NF membranes showed reasonable antifouling characteristics having flux recovery ratio of more than 90% and a flux decline ratio of less than 10%. Copyright © 2015 John Wiley & Sons, Ltd.     

Preparation of polyaniline coating on a stainless-steel wire using electroplating and its application to the determination of six aromatic amines using headspace solid-phase microextraction

A novel polyaniline (PANI) coating was prepared on a stainless-steel wire for solid-phase microextraction by electroplating method. For better mechanical strength, the stainless-steel wire was used instead of the fused silica fiber. The electroplating method had advantages of ease of preparation and simple equipments. The PANI fiber was evaluated by analyzing six aromatic amines (aniline, N,N-dimethylaniline, m-methylaniline, 2,4-dimethylaniline, 2-chloroaniline, 3,4-dichloroaniline) in water. After the analytical procedure was optimized, the linearity was from 4.8 to 2.75 x 10(4) microg L(-1) and the detection limits was from 0.019 to 1.06 microg L(-1). Relative standard deviations were found to be 2.02-6.00%. Good recoveries were obtained when wastewater samples were analyzed.     

改性316L不锈钢表面聚苯胺的制备及电化学性能

采用原位氧化技术调整316L不锈钢(SS316L)基体元素Cr和Ni在界面的浓度和分布, 形成了Ni和Cr富集改性界面. 应用计时电位技术, 通过Cr和Ni改性层催化草酸溶液中的苯胺单体在其表面吸附并聚合, 在SS316L表面沉积了附着力良好的聚苯胺(PANI)膜. 与SS316L相比, 表面富Ni-Cr的SS316L在涂覆PANI膜后, 在80 ℃ 0.5 mol/L H₂SO₄+5 mg/L F^-溶液中阳极和阴极的腐蚀电位分别提高470和500 mV, 维钝电流均下降2~3个数量级; 在模拟质子交换膜燃料电池运行环境中, 经36000 s恒电位极化, 其阳极和阴极的腐蚀电流分别下降约1和2个数量级, 腐蚀速度分别约为6~9 和< 5 μA/cm²; 在1.4 MPa压力下, 聚苯胺膜层与Toray 060碳纸间接触电阻下降约250 mΩ·cm². SS316L表面形成富Ni-Cr改性层并涂覆聚苯胺膜后, 其耐蚀性和导电性均明显优于原始SS316L, 这主要取决于富Ni-Cr改性层的结构、 组成和聚苯胺膜的厚度.     

Preparation and characterization of a composite PDMS membrane on CA support

Polydimethylsiloxane (PDMS) is the most commonly used membrane material for the separation of condensable vapors from lighter gases. In this study, a composite PDMS membrane was prepared and its gas permeation properties were investigated at various upstream pressures. A microporous cellulose acetate (CA) support was initially prepared and characterized. Then, PDMS solution, containing crosslinker and catalyst, was cast over the support. Sorption and permeation of C₃H₈, CO₂, CH₄, and H₂ in the prepared composite membrane were measured. Using sorption and permeation data of gases, diffusion coefficients were calculated based on solution‐diffusion mechanism. Similar to other rubbery membranes, the prepared PDMS membrane advantageously exhibited less resistance to permeation of heavier gases, such as C₃H₈, compared to the lighter ones, such as CO₂, CH₄, and H₂. This result was attributed to the very high solubility of larger gas molecules in the hydrocarbon‐based PDMS membrane in spite of their lower diffusion coefficients relative to smaller molecules. Increasing feed pressure increased permeability, solubility, and diffusion coefficients of the heavier gases while decreased those of the lighter ones. At constant temperature (25°C), empirical linear relations were proposed for permeability, solubility, and diffusion coefficients as a function of transmembrane pressure. C₃H₈/gas solubility, diffusivity, and overall selectivities were found to increase with increasing feed pressure. Ideal selectivity values of 9, 30, and 82 for C₃H₈ over CO₂, CH₄, and H₂, respectively, at an upstream pressure of 8 atm, confirmed the outstanding separation performance of the prepared membrane. Copyright © 2009 John Wiley & Sons, Ltd.     

Porous membranes modified by hyperbranched polymers: I. Preparation and characterization of PVDF membrane using hyperbranched polyglycerol as additive

Porous membranes were prepared via phase inversion process from casting solution composed of poly(vinylidene fluoride) (PVDF), N,N-dimethylacetamide (DMAc), and hyperbranched polyglycerol (HPG). The membranes were characterized in terms of surface and bulk chemical compositions, morphology, water contact angle, porosity, and water flux. The effects of HPG content on membrane structures and properties were investigated. The effect of HPG addition on the hydrophilicity was discussed as well when the compositions of coagulation bath were changed. To better understand the special effects of HPG on the structures and properties of the membranes, PVDF membranes prepared using HPG as the additive were compared with those prepared using polyethylene glycol (PEG) as the additive.     

Preparation and characterization of sulfonated poly(phenylene oxide) proton exchange composite membrane doped with phosphosilicate gels

A new class of proton exchange composite membranes made by incorporating phosphosilicate gels into SPPO matrix was prepared and characterized. The thermal stability was evaluated by TGA and DSC, and the amorphous structure information was provided from XRD. The experimental results showed that the composite membranes have good stability to oxidation by Fenton's reagent test, and the membrane dimension is hardly changed, even at high temperature. The hydration number values of the persulfonic acid group of composite membranes were lower than that of Nafion 112 at room temperature, but the water uptake of composite membranes at 80°C was higher than that of Nafion 112. With increasing relative humidity and doping amount, the conductivity of the composite membranes increased. Moreover, the conductivities of water-equilibrated composite membranes were higher than that of Nafion 112 (0.0871 S/cm) at room temperature, and the highest conductivity for the composite membrane was 0.216 S/cm. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation and characterization of polyethersulfone/silver nanocomposite ultrafiltration membrane for antibacterial applications

Antimicrobial ultrafiltration membranes were prepared by coating silver nanoparticles on the surface of polyethersulfone (PES) membranes which were fabricated via phase inversion induced by the immersion precipitation technique, and their morphology and performance were compared with the antimicrobial PES membranes synthesized by adding the silver nanoparticles into the casting solution during the phase inversion process. For this purpose, stable and uniform colloidal solutions of the silver nanoparticles were prepared by chemical reduction of silver salt using fructose and dimethylformamide as a reducing agent. The silver nanoparticles were characterized by ultraviolet–visible spectroscopy, X‐ray powder diffraction and dynamic light scattering analysis. The morphology and surface properties of the prepared membranes were examined by field emission scanning electron microscopy and atomic force microscopy analysis. Moreover, the separation properties, antimicrobial efficiency and amount of silver release from the PES nanocomposite membranes during the cross flow ultrafiltration were determined. The results indicated that the silver content of the coated PES membranes was greater than the membranes fabricated by the solution blending method. Also, the permeation flux of the silver‐coated membranes was similar to the neat PES membranes, while the membranes prepared by the second approach had less flux. The membranes synthesized by both coating and blending methods showed high antimicrobial and bactericidal activity against gram‐negative bacteria such as Escherichia coli and gram‐positive bacteria such as Staphylococcus aureus. Finally, the prepared antimicrobial membranes were successfully used for the ultrafiltration of raw milk to reduce the microbial load during the concentration process. Copyright © 2014 John Wiley & Sons, Ltd.     

Preparation,characterization and application of a novel thermal stable composite nanofiltration membrane

A thermal stable composite membrane was prepared by interfacial polymerization of piperazine (PIP) and trimesoyl chloride (TMC) on poly(phthalazinone ether amide) (PPEA) ultrafiltration membrane. The effect of reaction parameters on the performance of composite membranes was studied and optimized. The surface morphologies of the composite membrane and the substrate were observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The rejection of optimized composite membrane for dyes Congo red (CGR) and Acid chrome blue K (ACBK), the molecular weight (MW) of which is over 400, was over 99.2%, with a flux at about 180 L m⁻² h⁻¹. While the rejection for NaCl was only 18.2% with a flux over 270 L m⁻² h⁻¹, when tested at 1.0 MPa 60 °C. The composite membrane was applied in the desalination-purification experiment of dye ACBK and NaCl mixed solution. The flux of the membrane increased obviously as the operation pressure and/or temperature increased, while the rejection for dye was constant and kept over 99.3%. The purification experiments were accomplished effectively at 1.0 MPa, 80 °C. Only after five rounds of desalination-concentration experiment, about 160 min, the salt mixed in dye solution was fully removed. The initial flux of the eighth cycle was about 254 L m⁻² h⁻¹, which was only 20 L m⁻² h⁻¹ lower than that of the first round. The rejection of the membrane was constant and kept over 99.3% through out the eight cycles of purification experiment.     

Preparation and characterization of a homobifunctional silicone rubber membrane grafted with acrylic acid via plasma-induced graft copolymerization

Polyacrylic acid (PAA) was grafted onto the surface of silicone rubber membrane (SR) by plasma-induced graft copolymerization (PIP). Ar-plasma was used to activate the surface of SR. Also, a determination was made of the influences of plasma treatment power, pressure, time, grafted copolymerization reaction time, and monomer concentration on polymerization yield. The surface properties of SR were measured by ATR-FTIR, ESCA, and SIMS. In those analyses, the elemental composition and different carbon bindings on the surface of SR were examined by ESCA with the amount of O1s/C1s being approximately 0.7 at 60 s by Ar-plasma treatment (60 W, 200 mtorr). The peroxide group introduced on SR was measured via 1,1-diphenyl-2-picryhydrazyl (DPPH). The optimum amount of peroxide groups was 6.85 × 10⁻⁸ mol/cm² at 60 s of Ar-plasma treatment. The peroxide group (33D peak) was introduced onto the surface of SR by negative spectra of SIMS analysis after SR treatment by Ar-plasma. An increase was obtained in grafted polymerization yield with a region of 5 to 50% (v/v) of acrylic acid aqueous solution. Both sites of polyacrylic acid were detected after staining by toluidine blue O. That is, a homobifunctional membrane was developed via this surface modification method. © 1996 John Wiley & Sons, Inc.     

Preparation and characterization of polymer electrolyte membrane from chloroacetate chitosan/chitosan blended with epoxidized natural rubber

Chitosan-based membranes are among the most effective and efficient PEMs for fuel cells, however their low proton conductivity needs to be improved. In this study, chitosan, chloroacetate chitosan (CCS), chitosan blend with epoxidized natural rubber (ENR), and CCS with ENR blend based membranes were prepared by solution casting, crosslinked with NaOH and H₂SO₄, and investigated for physical, chemical, electrical and ionic properties. The functional groups were identified by ATR-FTIR spectroscopy and the peaks matched improved membrane properties. The surface roughness of the membranes was determined by AFM, and it increased with the amount of ENR. The electrical properties measured with an LCR meter showed that the CCS, CS and CS-B had the highest conductance, conductivity, capacitance and dielectric constant, while the CCS10/ENR8, CS10/ENR8 and CS15/ENR3 showed the highest resistance and resistivity. Furthermore, the CCS gave the lowest dissipation factor, which indicates its suitability for use in a PEM. In addition, the contact angle was relatively high for CS-B, CS and CCS.     

Preparation and characterization of phosphatidylcholine‐coated zirconia–magnesia stationary phase for artificial membrane chromatography

Immobilized artificial membrane chromatography stationary phase was prepared by coating soybean phosphatidylcholine (PC) on zirconia–magnesia micro‐particles. The stability and chromatographic properties were investigated and compared with the PC‐coated silica chromatography stationary phase prepared by the same method. PC‐coated zirconia–magnesia chromatography stationary phase was more stable than the silica especially on resisting organic solvents. Hydrophobic action was the main factor for the retention of analyte on the new artificial membrane chromatography stationary phase, and electrostatic interaction had some contribution to retention. In addition, the special interaction between analyte and matrix affected retention greatly. Basic solutes were appropriate to be analyzed on PC‐coated zirconia–magnesia stationary phase and acidic solutes were appropriate to be done on the silica one. Hence, the two different matrices artificial membrane stationary phases were perfectly complementary.     

Preparation and characterization of Nafion/SPEEK layered composite membrane and its application in vanadium redox flow battery

In order to reduce the cost of membrane used in vanadium redox flow battery (VRB) system while keeping its chemical stability, Nafion/sulfonated poly(ether ether ketone) (SPEEK) layered composite membrane (N/S membrane) consisting of a thin layer of recast Nafion membrane and a layer of SPEEK membrane were prepared by chemical crosslink the sulfonic acid groups of different ionomer membranes. Scanning electron microscopy (SEM) and IR spectra analysis of the membrane showed that Nafion layer was successfully deposited on the SPEEK membrane surface and an integral layered membrane structure was formed. The area resistance and permeability of vanadium ions of membrane were also measured. It was found that N/S membrane have a very low permeability of vanadium ions accompanied by a little higher area resistance compared with Nafion membrane. As a result, the VRB single cell with N/S membrane exhibited higher coulombic efficiency and lower voltage efficiency compared with VRB single cell with Nafion membrane. Although N/S membrane delivered relatively lower energy efficiency compared with Nafion membrane, its good chemical stability and low cost make it a suitable substitute for Nafion membrane used in VRB system.     

Wastewater treatment containing methylene blue dye as pollutant using adsorption by chitosan lignin membrane: Development of membrane,characterization and kinetics of adsorption

An influential subject of research is the use of lignin for effective removal of hazardous dyes from wastewater effluents utilizing green techniques. Lignin makes up to 10–25% of lignocellulosic biomass. In this study, a solvent evaporation approach was employed to construct a novel chitosan lignin membrane, which was then used to remove the methylene blue (MB) dye from water. The physicochemical, thermal, and morphological attributes were characterized by SEM, XRD, FTIR ATR, and TGA DSC. With higher lignin content in the membrane, its tensile strength was reduced. The dye was removed 95% of the time by the membrane, and the adsorption followed the Langmuir isotherm. The membranes could be recycled up to five times.     

Preparation and characterization of a poly(vinylbenzyl sulfonic acid)‐grafted FEP membrane

In this study, a novel polymer electrolyte membrane, poly(vinylbenzyl sulfonic acid)‐grafted poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP‐g‐PVBSA), has been successfully prepared by simultaneous irradiation grafting of vinylbenzyl chloride (VBC) monomer onto a FEP film and taking subsequent chemical modification steps to modify the benzyl chloride moiety to the benzyl sulfonic acid moiety. The chemical reactions for the sulfonation were carried out via the formation of thiouronium salt with thiourea, base‐catalyzed hydrolysis for the formation of thiol, and oxidation with hydrogen peroxide. Each chemical conversion process was confirmed by FTIR, elemental analysis, and SEM‐EDX. A chemical stability study performed with Fenton's reagent (3% H₂O₂ solution containing 4 ppm of Fe²⁺) at 70 °C revealed that FEP‐g‐PVBSA has a higher chemical stability than the poly(styrene sulfonic acid)‐grafted membranes (FEP‐g‐PSSA). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 563–569, 2010