A finite element approach to a coupled structural-acoustic radiation system with application to loudspeaker characteristic calculation

The finite element method is applied to an elastic shell which is vibrating to generate acoustic radiation. A vibrating shell of revolution backed by an enclosure in its rear side is to radiate sound waves into a semi-infinite space in front. As a numerical example, some characteristics of a direct radiator type loudspeaker model are calculated and discussed. The driving point impedance and the far field sound pressure frequency characteristics are shown, together with the effects of the radiation and the enclosure.     

The characteristics of sound radiation from a cylindrical shell coated with multiple compliant layers

The effect of multiple compliant layers on sound radiation from a finite cylindrical shell immersed in an infinite acoustic medium is studied. The transfer matrix is derived according to the continuous boundary conditions at each adjacent interface of the multi-layer system. With the shell theory and the acoustic wave equation, the theoretical model is developed to estimate the characteristics of sound radiation. The numerical calculation results show that the amount of the acoustic radiation power reduction increases as the wave speed or the density of the compliant layer decreases, and using multi-layer system could be more effective on noise reduction than the corresponding uniform single layer.     

On the sound field of a shallow spherical shell in an infinite baffle

A method is presented for calculating the far field sound radiation from a shallow spherical shell in an acoustic medium. The shell has a concentrated ring mass boundary condition at its perimeter representing a loudspeaker voice coil and is excited by a concentrated ring force exerted by the end of the voice coil. A Green's function is developed for a shallow spherical shell, which is based upon Reissner's solution to the shell wave equation [Q. Appl. Math. 13, 279-290 (1955)]. The shell is then coupled to the surrounding acoustic medium using an eigenfunction expansion, with unknown coefficients, for its deflection. The resulting surface pressure distribution is solved using the King integral together with the free space Green's function in cylindrical coordinates. In order to eliminate the need for numerical integration, the radiation (coupling) integrals are solved analytically to yield fast converging expansions. Hence, a set of simultaneous equations is obtained which is solved for the coefficients of the eigenfunction expansion. These coefficients are finally used in formulas for the far field sound radiation.     

Active control of radiated sound power of a smart cylindrical shell based on radiation modes

A new approach is proposed in this paper based on radiation modes to control the radiated sound pressure of a smart cylindrical shell equipped with piezoelectric sensor and actuators. The radiation modes determine the specific distribution of normal velocity of the shell that independently radiates sound to the surrounding space. In this study, the first radiation mode is controlled since it is the most effective mode in terms of the radiated power. The results indicate that most of the sound power is attenuated by controlling only this mode. The extended Hamilton’s principle, the Sanders shell theory and the assumed mode method are used to derive the equations of motion in a state space form that is suitable to design the controller. The radiated sound pressure is calculated using the simplified Kirchhoff-Helmholtz integral along with a Kalman filter to observe the system states, and a modified higher harmonic control (MHHC) is designed to attenuate the sound power. A numerical simulation demonstrated the effectiveness of the proposed approach compared to active vibration control (AVC) in attenuating the radiated sound in the low frequency domain.     

复杂结构冲击声合成及实验验证

以复杂结构受击振动响应的时域计算为目的, 讨论了结构阻尼的计算方法, 给出一种用于冲击声合成的综合数值方法, 并进行了实验验证. 首先, 考虑到阻尼是影响瞬态振动时变特性的重要因素, 详细讨论了两种模态阻尼的计算方法; 其次, 对阻尼板的受击振动和声辐射进行了时域仿真, 并与时域有限差分法的计算结果进行对比, 显示出两种声音合成方法的计算结果具有高度的一致性; 最后, 针对有限长圆柱壳的受击振动, 将合成声与实验录音进行了对比研究. 结果表明, 合成声与实际录音的时域包络、频谱结构以及衰减趋势基本一致, 证明了采用数值方法进行冲击声合成的有效性. 关键词： 声音合成 模态阻尼 冲击声 数值方法     

Generation of intense directional radiation during the fast motion of a liquid jet through a narrow dielectric channel

The results of theoretical and experimental studies of the cavitation phenomena in the volume of a moving liquid jet after its passing through thin and long oriented channels in dielectrics are considered. It is shown that the stationary generation of intense directional radiation in the optical range occurs in the moving jet volume as a threshold pressure is reached in the liquid (pure spindle oil). The parameters of radiation are close to those of laser radiation. The effective temperature of the generation region was estimated as corresponding to 50–100 eV. In some cases, optical radiation is accompanied by the pulsed generation of directional gamma radiation. These processes are accompanied by a sequence of high-voltage electric discharges of a great length in the liquid bulk and at the surface, corresponding to potential differences of 50–100 kV. One of the causes of the observed phenomena can be energetically favorable nuclear fusion reactions involving light nuclei in the liquid jet volume. It was shown that such processes can be efficiently stimulated by multibubble cavitation.     

水下三弹性柱壳耦合声散射特性研究

为研究3个并排无限长弹性圆柱壳受垂直于柱轴方向的平面声波作用的声散射特性,采用Fourier级数展开法建立了圆柱壳声散射数学物理模型,考虑了三圆柱壳弹性振动声辐射和刚性声散射,建立了3个壳体辐射声场和刚性散射声场的耦合作用关系,比对了等效散射强度的刚性散射分量与弹性散射分量,并分析了三壳体等效散射强度特性。计算结果表明:当ka₂>40,在频率f=3000 Hz以上频段,弹性分量对等效散射强度变化趋势的贡献可以忽略。当ka₂>30,在频率f=2400 Hz以上频段,弹性散射分量对等效散射强度影响不超过3 dB;三壳与单壳的等效散射强度在0°入射角方位相当,其它方位三壳体等效散射强度明显大于单壳体。本文的理论公式可推广到任意数量阻抗柱的声透射和声反射问题。      

Lower RCS directional antenna by left-handed material

We theoretically study the radiation of a current line source with a surrounding cylindrical shell of left-handed material (LHM). The far-field radiation pattern is obtained by solving the Maxwell equation in a cylindrical coordinate, which show that this radiation system has good directional emission characteristics and can be used as a directive antenna. The directive emission is explained due to the negative refraction and the focus effect occurring at the interface of the LHM shell. Compared with the parabolic reflector antenna with the same aperture size, our antenna has lower radar cross-section (RCS) in a broadband frequency range, providing a way to realize lower RCS antenna.     

水下复杂壳体结构在多源激励下的振动及声辐射特性研究

为了综合评估水下复杂壳体结构在多源激励下的振动与声辐射特性,专门设计了一个多舱段复杂壳体模型,分别进行了单台设备激励、多台设备激励的壳体振动与声辐射试验。试验结果表明,多源激励下的结构响应和辐射声场可以近似为单源激励下结构响应和辐射声场的非相干叠加。通过对激励源与结构响应、辐射声场之间传递关系的理论分析,讨论了以单源激励响应非相干叠加合成得到多源激励响应的合理性和误差。研究结果对复杂壳体结构在实际激励下的振动与噪声预报具有重要价值。      

三维浅海下弹性结构声辐射预报的有限元-抛物方程法

利用多物理场耦合有限元法对结构和流体适应性强、抛物方程声场计算高效准确的特点,提出了三维浅海波导下弹性结构声振特性研究的有限元-抛物方程法.该方法采用多物理场耦合有限元理论建立浅海下结构近场声辐射模型,计算局域波导下结构声振信息,并提取深度方向上复声压值作为抛物方程初始值;然后采用隐式差分法求解抛物方程以步进计算结构辐射声场.重点介绍了该方法对浅海下结构声辐射计算的准确性、高效性以及快速收敛性后,对Pekeris波导中有限长弹性圆柱壳的声振特性进行了分析.研究得出,当圆柱壳靠近海面(海底)时,其耦合频率比自由场下的要高(低),当潜深达到一定范围时,与自由场耦合频率基本趋于一致;在低频远场,结构辐射场与同强度点源声场具有一定的等效性,且等效距离随着频率增加而增加;由于辐射声场受结构振动模态、几何尺寸和简正波模式影响,结构辐射场传播的衰减规律按近场声影响区、球面波衰减区、介于球面波和柱面波衰减区、柱面波衰减区四个扩展区依次进行.     

三弹性圆柱壳体多重耦合声辐射计算方法

为研究多圆柱壳组合结构的声辐射特性,采用模态叠加法建立了3个并排无限长弹性圆柱壳的振动声散射耦合物理模型,充分考虑了三圆柱壳的表面振动与散射声场的耦合,其中散射声场可分解为各圆柱壳刚性散射声场和弹性辐射声场的叠加,数学上将各壳间的声场耦合关系通过柱函数加法公式描述。利用该物理模型,分析了多重散射对稳态声场求解结果的影响,比较了三圆柱壳耦合系统与单个圆柱壳系统的辐射声场指向性、声压级及辐射声功率级的差异及其产生机理,结果表明:结构弹性耦合声辐射不仅在低频对总声场有显著影响,在高频范围也不可忽略;另外,针对本文设定参数的组合圆柱壳,在150 Hz以上频段,两旁圆柱壳对中间圆柱壳在正横方位产生了声辐射遮蔽效应,垂直方位则体现声泄漏作用。本文建立的方法可推广到三维空间任意多壳结构的声振耦合建模。      

The decoupling of the active structural acoustic control based on the theory of radiation modes

With the theory of radiation modes,piezoceramics are used as control actuators in the active control of sound radiation.According to the characteristics of the first four radiation mode shapes,the arrangement of four group of actuators is presented.Theoretical analysis and numerical calculation demonstrate that the four group of actuators can not only reduce the sound power effectively,but also decouple the control equations.While controlling of the sound powers of the first four radiation modes,these actuators can convert the complicated control system with multiple input/output into several simple and independent systems with single input/output.     

环筋对水下平底圆柱壳的声振特性影响

本文建立了计算两端带平底板的有限长圆柱壳水中声辐射的FEM／BEM三维模型，探索了加筋的高度、宽度、数目对平底圆柱壳的辐射功率、辐射效率、法向声强、声场指向性的影响规律。计算方法是在有限元软件ANSYS中做加筋平底圆柱壳建模、模态分析基础上，将有关数据（网格、模态）导入边界元软件SYSNOISE中计算流体结构耦合状态下的辐射声场特性。结果表明：（1）随着环筋高度、宽度增大，激励点声压峰和法向声强峰在0-400Hz频率范围内数目减少且峰向高频方向移动，同时辐射声功率在减小（除个别模态峰值外），而辐射效率随筋高增大而增大。（2）环筋数目的增加使激励点辐射声压和法向声强峰数目明显减少，使辐射声功率明显低于无筋圆柱壳的辐射声功率，辐射效率随环筋数目增大而增大。（3）环筋宽度变化对声场指向性影响不大；圆柱壳声场指向性随环筋高度和数目增加出现较大变化，尤其是在研究的频段内的f=51Hz和f=301Hz上。这对于水下结构辐射噪声预报以及噪声抑制具有重要意义。     

爆炸作用驱动液体抛撒初始阶段数值仿真

 针对灭火战斗部引战配合设计,研究爆炸作用驱动液体（水基灭火剂）抛撒初始阶段的特性。依据典型灭火战斗部的结构建立数值仿真模型,采用LS-DYNA软件进行仿真计算,分别获得了加载系数（驱动装药与液体的质量比）对壳体破裂时间和壳体破裂初期液体/空气界面运动速度的影响规律,以及液体/空气界面后续的运动特性。进行了同条件下爆炸驱动水基灭火剂抛撒实验,得到了不同加载系数条件下壳体破裂初期液体/空气界面的运动速度。实验结果与数值仿真结果吻合良好,表明所采用的数值仿真方法具有正确性和有效性,对相关问题的研究具有重要参考价值。     

Axisymmetric vibrations of a viscous-fluid-filled piezoelectric spherical shell and the associated radiation of sound

Axisymmetric vibrations of a viscous-fluid-filled piezoelectric sphere, with radial polarization, submerged in a compressible viscous fluid medium are investigated. The oscillations are harmonically driven by an axisymmetrically applied electric potential difference across the surface of the shell. A theoretical formulation cast the piezoelectric shell problem into a corresponding problem of an elastic shell with the contribution of piezoelectricity confined to slightly modified in vacuum natural frequencies and their associated mode shapes. It is noted that the fluid inside the shell will have a dominating influence on the vibrational characteristics of the submerged shell. The circular components of the natural frequency spectra closely follow those of the fluid-filled shell in vacuo. Furthermore, the corresponding damping components of those natural frequencies are rather small, making acoustic radiation and under-damped oscillation possible for an infinite number of natural frequencies. The characteristics of natural frequencies are elucidated using a fluid-filled polyvinglindene fluoride (PVDF) shell submerged in both air and water as an example. It is found that the piezoelectric parameters that contribute to the shell's natural frequencies is of a small order for thin PVDF shells, and is thereby negligible. It is noted that, with the mechanical constant typically associated with piezoelectric materials, fluid viscosity could have a significant effect on some vibrations. In certain cases, a natural frequency associated with a minimum viscous damping and a maximum of total damping (indicating highly efficient acoustic radiation) is possible with such a frequency.The vibrational characteristics, fluid loading, and energy flow are evaluated for a fluid-filled PVDF shell submerged in air and water. The inclusion of fluid inside the shell is shown to produce various narrow band peaks responses, vibrational absorbing frequencies, and non-dissipating frequencies. Those vibrational characteristics could have many potential applications. For example, the interior fluid could offer the option of generating a desired narrow band near resonant sound radiation while keeping power dissipation due to fluid viscosity to a minimum. Those well-defined narrow band characteristics also open up possibilities of using a vibrating, fluid-filled shell as a micro scale sensor for sensing and detection applications.     

径向声子晶体隔声特性*

该文构造了由两种匀质材料交替分布的径向声子晶体柱壳模型。首先,针对声波在其中的轴对称传播情况进行了理论分析,建立了声波由内向外传播的传递矩阵,进而导出了声压透射系数和隔声量表达式。采用数值分析的方法系统地讨论了径向声子晶体柱壳的隔声特性,并与单一材质柱壳的传播规律进行对比分析,其次,借助有限元仿真分析的手段对数值结果进行了验证。最后,详细分析了内外流体的特性阻抗对径向声子晶体柱壳隔声特性的影响,得到了相应的参数影响规律。研究表明,径向声子晶体柱壳存在声波带隙,导致其在带隙范围内的隔声效果远远优于单材质柱壳,并且该结构的固有特性突破了质量定律的限制;声波带隙内表面局域态现象出现与否由内外声场和结构场共同决定。     

部分浸没圆柱壳声固耦合计算的半解析法研究

部分浸没圆柱壳-流场耦合系统的声振分析是一种典型的半空间域内声固耦合问题,其振动及声学计算目前主要依赖于数值方法求解,但无论从检验数值法还是从机理上揭示其声固耦合特性,解析或半解析方法的发展都是不可或缺的.本文提出了一种半解析方法,先将声场坐标系建立在自由液面上,采用正弦三角级数来满足自由液面上的声压释放边界条件;接着基于二维Flügge薄壳理论建立了以圆柱圆心为坐标原点的壳-液耦合系统的控制方程;然后再利用Galerkin法处理声固耦合界面的速度连续条件,推导得到声压幅值与壳体位移幅值之间的关系矩阵并求解该耦合系统的振动和水下声辐射.与有限元软件Comsol进行了耦合系统自由、受迫振动和水下辐射噪声计算结的对比分析,表明本文方法准确可靠.本文的研究为解析求解弹性结构与声场部分耦合的声振问题提供了新的思路.     

Duct noise radiation through a jet flow

The radiation of internal (or core) noise for aircraft turbojet or turbofan engines is studied analytically. The geometry of a typical engine is simplified for analytical considerations to a hemispherical shell with a jet flow and internal sound emanating through a circular hole on the axis. A linearized theory is used to derive a flow modified spherical wave equation. A forced separation technique is used to produce a modified Legendre equation describing the angular variation of the acoustic radiation field. Then a numerical technique is described for obtaining a general field solution by progressively imposing continuity of pressure across hemispherical shells as the solution is marched from near field to the far field. In a companion paper, numerical results are presented and compared with experimental results from a test configuration identical to that described by the theory.     

Dynamic behavior and sound transmission analysis of a fluid-structure coupled system using the direct-BEM/FEM

A direct-BEM/Fem method was proposed to analyze the vibration and acoustic radiation characteristics of a submerged structure. Model parameters of the structure and the fluid-structure interaction due to surrounding water were analyzed by using FEM and direct BEM. Vibration velocity of the outer hull surface and underwater sound pressure were computed through modal superposition technique. The direct-BEM/FEM method was first validated by analyzing a submerged cylindrical shell, then was used to analyze the vibro-acoustic behavior of a submarine stern structure. The results have demonstrated the direct-BEM/FEM method is more effective than FEM in computing the underwater sound radiation of the stern structure.     

基于声辐射模态的有源控制解耦

在声辐射模态有源噪声控制策略框架下,选择压电陶瓷片作为控制作动器。根据前四阶声辐射模态形状特点提出了四种压电作动器位置布置方法。理论分析及数值计算表明,以这种方式布放的压电作动器不仅能有效地降低结构辐射的声功率,而且控制过程中这四组作动器分工明确,从而将控制方程解耦。在控制前几阶声辐射模态声功率时可以将复杂的多输入/多输出控制系统转变为几个简单的、互相独立的单输入/单输出控制系统。