Optimization towards reduction of efficiency droop in blue GaN/InGaN based light emitting diodes

Light emitting diodes (LEDs) based on GaN/InGaN material suffer from efficiency droop at high current injection levels. We propose multiple quantum well (MQW) GaN/InGaN LEDs by optimizing the barrier thickness and high–low–high indium composition to reduce the efficiency droop. The simulation results reflect a significant improvement in the efficiency droop by using barrier width of 10 nm and high–low–high indium composition in MQW LED.     

The effect of junction temperature on the optoelectrical properties of InGaN/GaN multiple quantum well light-emitting diodes

Thermal effects on the optoelectrical characteristics of green InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) have been investigated in detail for a broad temperature range, from 30 °C to 100 °C. The current-dependent electroluminescence (EL) spectra, current–voltage (I–V) curves and luminescence intensity–current (L–I) characteristics of green InGaN/GaN MQW LEDs have been measured to characterize the thermal-related effects on the optoelectrical properties of the InGaN/GaN MQW LEDs. The experimental results show that both the forward voltages decreased with a slope of ?3.7 mV/K and the emission peak wavelength increased with a slope of +0.02 nm/K with increasing temperature, indicating a change in the contact resistance between the metal and GaN layers and the existence of a band gap shrinkage effect. The junction temperature estimated from the forward voltage and the emission peak shift varied from 25.6 to 14.5 °C and from 22.4 to 35.6 °C, respectively. At the same time, the carrier temperature decreased from 371.2 to 348.1 °C as estimated from the slope of high-energy side of the emission spectra. With increasing injection current, there was found to be a strong current-dependent blueshift of ?0.15 nm/mA in the emission peak wavelength of the EL spectra. This could be attributed to not only the stronger band-filling effect but also the enhanced quantum confinement effect that resulted from the piezoelectric polarization and spontaneous polarization in InGaN/GaN heterostructures. We also demonstrate a helpful and easy way to measure and calculate the junction temperature of InGaN/GaN MQW LEDs.     

The effect of SixNy interlayer on the quality of GaN epitaxial layers grown on Si(1 1 1) substrates by MOCVD

In the present paper, the effects of nitridation on the quality of GaN epitaxial films grown on Si(1 1 1) substrates by metal–organic chemical vapor phase deposition (MOCVD) are discussed. A series of GaN layers were grown on Si(1 1 1) under various conditions and characterized by Nomarski microscopy (NM), atomic force microscopy (AFM), high resolution X-ray diffraction (HRXRD), and room temperature (RT) photoluminescence (PL) measurements. Firstly, we optimized LT-AlN/HT-AlN/Si(1 1 1) templates and graded AlGaN intermediate layers thicknesses. In order to prevent stress relaxation, step-graded AlGaN layers were introduced along with a crack-free GaN layer of thickness exceeding 2.2 μm. Secondly, the effect of in situ substrate nitridation and the insertion of an Si_xN_y intermediate layer on the GaN crystalline quality was investigated. Our measurements show that the nitridation position greatly influences the surface morphology and PL and XRD spectra of GaN grown atop the Si_xN_y layer. The X-ray diffraction and PL measurements results confirmed that the single-crystalline wurtzite GaN was successfully grown in samples A (without Si_xN_y layer) and B (with Si_xN_y layer on Si(1 1 1)). The resulting GaN film surfaces were flat, mirror-like, and crack-free. The full-width-at-half maximum (FWHM) of the X-ray rocking curve for (0 0 0 2) diffraction from the GaN epilayer of the sample B in ω-scan was 492 arcsec. The PL spectrum at room temperature showed that the GaN epilayer had a light emission at a wavelength of 365 nm with a FWHM of 6.6 nm (33.2 meV). In sample B, the insertion of a Si_xN_y intermediate layer significantly improved the optical and structural properties. In sample C (with Si_xN_y layer on Al_0.11Ga_0.89N interlayer). The in situ depositing of the, however, we did not obtain any improvements in the optical or structural properties.     

Structural and optical properties of InxGa1−xAs strained layers grown on GaAs substrates by MOVPE

In_xGa_1−xAs/GaAs pseudomorphic structures were grown by metalorganic vapor phase epitaxy. Reciprocal space mapping were recorded in the vicinity of (0 0 4) and (1 1 5) nodes using high resolution X-ray diffraction (HRXRD) in order to determine strain tensor components, indium compositions and thicknesses of alloys. Near-infrared photoluminescence (PL) was performed at 10 K. The impact of strain on PL response was revealed by peak energy positions and line width. In addition, valence-band splitting (VBS) and the shift of the heavy-hole were measured. Besides, photoreflectance (PR) at room temperature was useful to establish experimentally the dependence of VBS and band energy shifts (E₀ and E₀+∆₀) on elastic strain due to lattice mismatches. Other parameters such as the internal electric-field and the electro-optical energy were determined from Franz–Keldysh oscillations analysis. Good correlation between the results obtained from all investigated techniques and theoretical predictions was confirmed.     

Luminescence properties of InAs quantum dots formed by a modified self-assembled method

The luminescence properties of self-assembled InAs quantum dots (QDs) on GaAs (1 0 0) substrates grown by molecular beam epitaxy have been investigated using temperature-dependent photoluminescence (PL) and time-resolved PL (TRPL). InAs QDs were grown using an In-interruption growth technique, in which the indium flux was periodically interrupted. InAs QDs grown using In-interruption showed reduced PL linewidth, redshifted PL emission energy, increased energy level spacing between the ground state and the first excited state, and reduced decay time, indicating an improvement in the size distribution and size/shape of QDs.     

Structural and optical properties of an InxGa1−xN/GaN nanostructure

The structural and optical properties of an In_xGa_1−xN/GaN multi-quantum well (MQW) were investigated by using X-ray diffraction (XRD), atomic force microscopy (AFM), spectroscopic ellipsometry (SE) and photoluminescence (PL). The MQW structure was grown on c-plane (0 0 0 1)-faced sapphire substrates in a low pressure metalorganic chemical vapor deposition (MOCVD) reactor. The room temperature photoluminescence spectrum exhibited a blue emission at 2.84 eV and a much weaker and broader yellow emission band with a maximum at about 2.30 eV. In addition, the optical gaps and the In concentration of the structure were estimated by direct interpretation of the pseudo-dielectric function spectrum. It was found that the crystal quality of the InGaN epilayer is strongly related with the Si doped GaN layer grown at a high temperature of 1090 °C. The experimental results show that the growth MQW on the high-temperature (HT) GaN buffer layer on the GaN nucleation layer (NL) can be designated as a method that provides a high performance InGaN blue light-emitting diode (LED) structure.     

Fabrication of InGaN/GaN stripe structure on (1 1 1)Si and stimulated emission under photo-excitation

InGaN/GaN QW laser structure was investigated on a GaN trapezoid grown on (1 1 1)Si substrate by selective MOVPE. The dislocation density in the active layer was reduced by a two-step growth method adopting facet controlled epitaxial lateral overgrowth (FACELO). A sample with 350 μm long cavity length showed narrowing of the spectral peak under optical excitation. The compositional non-uniformity originating from the ridge growth on the trapezoid is removed by adopting re-evaporation phenomenon under heat treatment during the growth process.     

Finite barrier width effects on exciton states and optical properties in wurtzite InGaN/GaN quantum well

Exciton states and optical properties in wurtzite (WZ) InGaN/GaN quantum well (QW) are investigated theoretically, considering finite barrier width and built-in electric field effects. Numerical results show that when the barrier width increases, the ground-state exciton binding energy, the interband transition energy and the integrated absorption probability increase first and then they are insensitive to the variation of the barrier width. For any barrier width, the ground-state exciton binding energy and the integrated absorption probability have a maximum when the well width is 1 nm; moreover, the integrated absorption probability goes to zero when the well width is larger than 6 nm. In addition, the competition effects between the built-in electric field and quantum confinement are also investigated in the WZ InGaN/GaN QW.     

Photoluminescence study of InGaN/GaN multiple-quantum-well with Si-doped InGaN electron-emitting Layer

InGaN/GaN multiple-quantum-well (MQW) structure with Si-doped InGaN electron-emitting layer (EEL) was grown by metal–organic chemical vapor deposition and their characteristics were evaluated by photoluminescence (PL) measurements. In a typical structure, a low indium composition and wide potential well was used to be an EEL, and a six-fold MQW was used to be an active layer where the injected carriers recombine. By comparing the PL spectral characteristics of the MQW samples, the PL intensity of MQW with EEL is about 10 times higher than that of typical MQW. Experimental results indicate that the high electron capture rate of the MQW active region can be achieved by employing EEL.     

具有超晶格应力调制结构的绿光InGaN/GaN多量子阱的发光特性

研究了具有InGaN/GaN超晶格(SL)插入结构的绿光InGaN/GaN多量子阱(MQW)的发光特性。结构测试表明,SL插入结构并没有引起MQW中平均In组份的增加,而是改变了In组份的分布,形成了高In组份的量子点和低In组份量子阱。其电致发光(EL)谱和光致发光(PL)谱均出现了双发光峰。我们认为这两个 峰分别来自于量子点和量子阱,且存在着载流子从阱向点转移的输运机制。最后变温PL积分强度的Arrhenius 拟合表明,SL插入结构并没有在MQW中引入新的缺陷,使其发光效率下降。     

InGaN/GaN多量子阱的组分确定和晶格常数计算

采用金属有机化学气相沉积(MOCVD)技术以蓝宝石为衬底在n型GaN单晶层上生长了InGaN/GaN多量子阱结构外延薄膜，利用高分辨X射线衍射(HRXRD)，卢瑟福背散射/沟道(RBS/channeling)，以及光致发光(PL)技术对InGaN/GaN多量子阱结构薄膜分别进行了平均晶格常数计算、In原子替位率计算和In组分的定量分析.研究表明：InGaN/GaN多量子阱的水平和垂直方向平均晶格常数分别为a_epi=0.3195nm，c_epi=0.5198nm，In原子的替位率为99.3%，利用HRXRD和RBS/channeling两种分析技术计算In的组分分别是0.023和0.026，并与样品生长时设定的预期目标相符合，验证了两种实验方法的准确性；而用室温条件下的光致发光谱(PL)来计算InGaN/GaN多量子阱中In的组分是与HRXRD和RBS/channeling的实验结果相差很大，说明用PL测试In组分的方法是不适宜的. 关键词： InGaN/GaN多量子阱 高分辨X射线衍射 卢瑟福背散射/沟道 光致发光     

Growth and electrical characterization of type II InAs/GaSb superlattices for midwave infrared detection

Herein, we report a type II InAs/GaSb superlattice structure (SLS) grown on GaSb(1 0 0) substrates by molecular beam epitaxy (MBE) and its electrical characterization for mid-wavelength infrared detection. A GaSb buffer layer was grown under optimized SLS growth conditions, which can decrease the occurrence of defects for similar pyramidal structures. The complications associated with these conditions include oxide desorption of the substrate, growth temperature of the SLS, the V/III ratio during superlattice growth and the shutter sequence. High-resolution X-ray diffraction (HRXRD) shows the sixth satellite peak, and the period of the SLS was 52.9 Å. The atomic force microscopy (AFM) images indicated that the roughness was less than 2.8 nm. High-resolution transmission electron microscopy (HRTEM) images indicated that the SLS contains few structural defects related to interface dislocations or strain relaxation during the growth of the superlattice layer. The photoresponse spectra indicated that the cutoff wavelength was 4.8 μm at 300 K. The SLS photodiode surface was passivated by a zinc sulfide (ZnS) coating after anodic sulfide.     

Changes of MQW photoluminescence under alpha particle irradiation

Undoped multiple quantum well (MQW) samples grown by the molecular beam epitaxy method were irradiated by 5.15 MeV energy alpha particles. A strong influence of irradiation on the photoluminescence (PL) intensity was observed in these nearly intrinsic samples: the PL intensity at liquid nitrogen and room temperatures decreased by more than two orders of magnitude at alpha particle fluence of 10¹¹cm ^− 2. The dependence of the PL intensity on irradiation dose is described by a rate equation model that takes into account the generation of nonradiative point centers in barriers and wells of the MQW structure during irradiation.     

Influence of barrier thickness on the structural and optical properties of InGaN/GaN multiple quantum wells

The structural and optical properties of InGaN/GaN multiple quantum wells(MQWs) with different barrier thicknesses are studied by means of high resolution X-ray diffraction(HRXRD), a cross-sectional transmission electron microscope(TEM), and temperature-dependent photoluminescence(PL) measurements. HRXRD and cross-sectional TEM measurements show that the interfaces between wells and barriers are abrupt and the entire MQW region has good periodicity for all three samples. As the barrier thickness is increased, the temperature of the turning point from blueshift to redshift of the S-shaped temperature-dependent PL peak energy increases monotonously, which indicates that the localization potentials due to In-rich clusters is deeper. From the Arrhenius plot of the normalized integrated PL intensity, it is found that there are two kinds of nonradiative recombination processes accounting for the thermal quenching of photoluminescence,and the corresponding activation energy(or the localization potential) increases with the increase of the barrier thickness.The dependence on barrier thickness is attributed to the redistribution of In-rich clusters during the growth of barrier layers,i.e., clusters with lower In contents aggregate into clusters with higher In contents.     

Midinfrared photoluminescence from SnTe/PbTe/CdTe double quantum wells grown by molecular beam epitaxy

Molecular beam epitaxial growth and photoluminescence (PL) properties of SnTe/PbTe/CdTe double quantum wells (DQWs) on (1 0 0)-oriented GaAs substrates are reported. These DQWs were consisted of a very thin SnTe/PbTe QW nested in a 10-nm-thick PbTe/CdTe QW. Efficient midinfrared PL was observed from the DQWs at 300 K in agreement with the coherent SnTe/PbTe growth on the thick CdTe barrier layer. The PL peak wavelength of the DQWs was found to increase with the SnTe thickness d by covering a wide range of the 3–5 μm atmospheric window with d≤2.5 monolayer.     

ZnS thin films grown by atomic layer deposition on GaAs and HgCdTe substrates at very low temperature

ZnS films grown on GaAs and HgCdTe substrates by atomic layer deposition (ALD) under very low temperature were investigated in this work. ZnS films were grown under several temperatures lower than 140 °C. The properties of the films were investigated with high-resolution X-ray diffraction (HRXRD), scanning electron microscope (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The results showed the ZnS films were polycrystalline. The growth rate monotonically decreased with temperature, as well as the root mean square (r.m.s) roughness measured by AFM. XPS measurement revealed the films were stoichiometric in Zn and S.     

Observation of large Zeeman splitting in GaGdN/AlGaN ferromagnetic semiconductor double quantum well superlattices

Symmetric GaGdN/AlGaN (Gd concentration: 2%) and GaN/AlGaN double quantum well superlattices (DQW-SLs) were grown by radio-frequency plasma-assisted molecular-beam epitaxy on GaN (0001) templates. Atomic steps were observed on all the sample surfaces by atomic force microscope. X-ray diffraction θ/2θ scan curves exhibited well-defined satellite structures. Room temperature ferromagnetism was confirmed for the GaGdN/AlGaN DQW-SL samples by using alternating gradient magnetometer. Strong photoluminescence was observed from both GaGdN and GaN QWs at higher energy side of GaN excitonic peak. Magneto-photoluminescence spectra for GaGdN/AlGaN DQW-SL samples showed a large magnetic field dependence of the excitonic energy by applying a magnetic field up to 7 T. The observed strong redshift of excitonic PL indicated an enhancement of Zeeman splitting of the free carrier energy levels in magnetic GaGdN/AlGaN DQW-SL. Enhanced g-factor was estimated to be about 60 for GaGdN/AlGaN DQW-SL sample with QW thickness of 1 nm.     

Properties of InGaN/GaN quantum wells and blue light emitting diodes

We have reported the effects of growth interruption time on the optical and structural properties of high indium content In_xGa_1−xN/GaN (x>0.2) multilayer quantum wells (QWs). The InGaN/GaN QWs were grown on c-plane sapphire by metal organic chemical vapor deposition. The interruption was carried out by closing the group-III metal organic sources before and after the growth of the InGaN QW layers. The transmission electron microscopy (TEM) images show that with increasing interruption time, the quantum-dot-like region and well thickness decreases due to indium reevaporation or the thermal etching effect. As a result the photoluminescence (PL) peak position was blue-shifted and the intensity was reduced. The sizes and number of V-defects did not differ with the interruption time. The interruption time is not directly related to the formation of defects. The V-defect originates at threading dislocations and inversion domain boundaries due to higher misfit strain. Temperature dependent PL spectra support the results of TEM measurements. Also, the electroluminescence spectra of light-emitting diode show that dominant mechanism in InGaN/GaN QWs is a localized effect in the quantum-dot-like regions.     

Si-delta doping and spacer thickness effects on the electronic properties in Si-delta-doped AlGaAs/GaAs HEMT structures

In this work, we investigate the effect of the δ-Si doping on the barrier and the spacer thickness on the electronic properties of AlGaAs/GaAs HEMTs structures grown by molecular beam epitaxy on (1 0 0) oriented GaAs substrates. Photoluminescence measurements as function of the temperature are used to determine the relaxation processes of the electron and the hole in the channel. The photoluminescence characterizations of Si-delta-doped AlGaAs/GaAs HEMTs structures have been studied in the 10–300 K temperature range. Low temperature PL spectra show the optical transition (E_e–h) that occurs between the fundamental states of electrons to holes in the GaAs channel. Increase of the Si-δ-doping density and decrease of the spacer width improve the two-dimensional electron gas confinement and decrease defects densities in the canal. The band structure of Si-delta-doped AlGaAs/GaAs HEMTs structures at T = 10 K has been studied theoretically using the finite differences method to self-consistently and simultaneously solve Schrödinger and Poisson equations written within the Hartree approximation.     

Effects of growth temperature modulated by HCl flow rate on the surface and crystal qualities of thick GaN by HVPE

We studied the influence of the growth temperature and HCl flow rate on the morphological evolution of crack-free thick GaN films by using a home-made horizontal hydride vapor phase epitaxy on sapphire substrates. Optical difference microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), and cathodoluminescence (CL) were carried out to reveal the surface property of the GaN epilayer. It was found that the higher growth temperature is a key factor to obtain mirror, colorless and flat GaN surface. However, this key effect of temperature was modulated by HCl flow rate (HCl > 15 sccm). The surface RMS roughness was reduced from 206 to 2.51 nm for 10 μm × 10 μm scan area when GaN was grown at 1070 °C with HCl flow rate up to 30 sccm. These samples also reduced their (0 0 0 2) FWHM result from 1000 to 300 arcsec and showed a strong near-band-edge peak in CL spectra. Results indicated that growth temperature influence growth velocities on different crystalline planes, which will lead to the different morphologies obtained. High growth temperature can improve the lateral growth rate of vertical {1 1 ? 2 0} facets and reduce the vertical growth rate of top {0 0 0 1} facet combined with higher HCl flow rate, which leads to completely coalescence of surface.