Investigation of a graded channel InGaAs/GaAs heterostructure transistor

An InGaAS/GaAs heterostructure transistor utilizing a gradedIn_xGa_1 − xAs channel grown by low-pressure metal-olorganic chemical vapor deposition has been demonstrated. A negative differential resistance (NDR) phenomenon is observed. Electron mobilities are significantly improved by using the graded InGaAs channel. For the In composition varying fromx =  0.25 (at the buffer–channel interface) to x =  0.1 (at the spacer–channel interface) structure, a peak extrinsic transconductance of 24.6 S mm ^− 1(atV_DS =  6.5 V,V_GSstep =  − 0.5 mV) and a saturation current density as high as 555 mA mm ^− 1for a gate length of 1.5 μ m are obtained.     

Effects of UVB radiation on the agarophyte Gracilaria domingensis (Rhodophyta,Gracilariales): Changes in cell organization,growth and photosynthetic performance

The effects of ultraviolet radiation-B (UVBR) in apical segments of the red macroalgae Gracilaria domingensis (Kützing) Sonder ex Dickie were examined in vitro. Over a period of 21 days, the segments were cultivated and exposed to photosynthetically active radiation (PAR) at 80 μmol photons m^?2 s^?1 and PAR + UVBR at 1.6 W m^?2 for 3 h per day. The samples were processed for electron microscopy, as well as histochemical analysis, and growth rate, photosynthetic pigment contents and photosynthetic performance were measured. Toluidine Blue reaction showed metachromatic granulations in vacuole and lenticular thickness, while Coomassie Brilliant Blue showed a higher concentration of cytoplasmic organelles, and Periodic Acid Schiff stain showed an increase in the number of floridean starch grains. UVBR also caused changes in the ultrastructure of cortical and subcortical cells, which included an increased number of plastoglobuli, changes in mitochondrial organization, destruction of chloroplast internal organization, and the disappearance of phycobilisomes. The algae cultivated under PAR-only showed growth rates of 6.0% day^?1, while algae exposed to PAR + UVBR grew only 2.8% day^?1. Compared with algae cultivated with PAR-only, the contents of photosynthetic pigments, including chlorophyll a, phycoerythrin, phycocyanin and allophycocyanin, decreased after exposure to PAR + UVBR, and significant differences were observed. Finally, analysis of these four photosynthetic parameters also showed reduction after exposure to PAR + UVBR: maximum photosynthetic rate, photosynthetic efficiency, photoinhibition and relative electron transport rate. Taken together, these findings strongly suggested that UVBR negatively affects the agarophyte G. domingensis.     

Modeling of electrical and optical characteristics of near room-temperature CdS/ZnSe based NIR photodetectors

Results of modeled photodetector characteristics in (CdS/ZnSe)/BeTe multi-well diode with p–i–n polarity are reported. The dark current density (J–V) characteristics, the temperature dependence of zero-bias resistance area product (R₀A), the dynamic resistance as well as bias dependent dynamic resistance (R_d) and have been analyzed to investigate the mechanisms limiting the electrical performance of the modeled photodetectors. The quantum efficiency, the responsivity and the detectivity have been also studied as function of the operating wavelength. The suitability of the modeled photodetector is demonstrated by its feasibility of achieving good device performance near room temperature operating at 1.55 μm wavelength required for photodetection in optical communication. Quantum efficiency of ∼95%, responsivity ∼0.6 A/W and D^* ∼ 5.7 × 10¹⁰ cm Hz^1/2/W have been achieved at 300 K in X BeTe conduction band minimum.     

Ultra-fast grain boundary diffusion and its contribution to surface segregation on a martensitic steel. Experiments and modeling

Phosphorus surface segregation was measured by Auger Electron Spectroscopy on a 17-4 PH martensitic stainless steel at 450, 550 and 600 °C. Surface segregation was shown to be much faster than expected which was attributed to a high contribution of phosphorus diffusion along the former austenitic grain boundaries. A model of surface segregation was developed following the Darken–du Plessis approach and taking account of both bulk and grain boundary solute diffusion. The phosphorus grain boundary diffusion coefficient in 17-4 PH was estimated: D_GB^< = 6.2 10⁴ exp(? 157 kJ mol^? 1/RT)cm² s^? 1. It is found to be more than three orders of magnitude higher in 17-4 PH steel than in α-iron.     

Thermal and sonochemical synthesis of porous (Ce,Zr)O2 mixed oxides from metal β-diketonate precursors and their catalytic activity in wet air oxidation process of formic acid

Porous (Ce_0.5Zr_0.5)O₂ solid solutions were prepared by thermolysis (T = 285 °C) or sonolysis (20 kHz, I = 32 W cm⁻², P_ac = 0.46 W mL⁻¹, T = 200 °C) of Ce(III) and Zr(IV) acetylacetonates in oleylamine or hexadecylamine under argon followed by heat treatment of the precipitates obtained in air at 450 °C. Transmission Electron Microscopy images of the samples show nanoparticles of ca. 4–6 nm for the two synthetic approaches. The powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray and μ-Raman spectroscopy of solids obtained after heat treatment indicate the formation of (Ce_0.5Zr_0.5)O₂ solid solutions with a metastable tetragonal crystal structure for the two synthetic routes. The specific surface area of the samples varies between 78 and 149 m² g⁻¹ depending on synthesis conditions. The use of Barrett–Joyner–Halenda and t-plot methods reveal the formation of mixed oxides with a hybrid morphology that combines mesoporosity and microporosity regardless of the method of preparation. Platinum nanoparticles were deposited on the surface of the mixed oxides by sonochemical reduction of Pt(IV). It was found that the materials prepared by sonochemistry exhibit better resistance to dissolution during the deposition process of platinum. X-ray photoelectron spectroscopy analysis shows the presence of Pt(0) and Pt(II) on the surface of mixed oxides. Porous (Ce_0.5Zr_0.5)O₂ mixed oxides loaded with 1.5 %wt. platinum exhibit high activity in catalytic wet air oxidation of formic acid at 40 °C.     

On the rate constants of OH + HO2 and HO2 + HO2: A comprehensive study of H2O2 thermal decomposition using multi-species laser absorption

Hydrogen peroxide (H₂O₂) and hydroperoxy (HO₂) reactions present in the H₂O₂ thermal decomposition system are important in combustion kinetics. H₂O₂ thermal decomposition has been studied behind reflected shock waves using H₂O and OH diagnostics in previous studies (Hong et al. (2009) [9] and Hong et al. (2010) [6,8]) to determine the rate constants of two major reactions: H₂O₂ + M → 2OH + M (k₁) and OH + H₂O₂ → H₂O + HO₂ (k₂). With the addition of a third diagnostic for HO₂ at 227 nm, the H₂O₂ thermal decomposition system can be comprehensively characterized for the first time. Specifically, the rate constants of two remaining major reactions in the system, OH + HO₂ → H₂O + O₂ (k₃) and HO₂ + HO₂ → H₂O₂ + O₂ (k₄) can be determined with high-fidelity.No strong temperature dependency was found between 1072 and 1283 K for the rate constant of OH + HO₂ → H₂O + O₂, which can be expressed by the combination of two Arrhenius forms: k₃ = 7.0 × 10¹² exp(550/T) + 4.5 × 10¹⁴ exp(?5500/T) [cm³ mol^?1 s^?1]. The rate constants of reaction HO₂ + HO₂ → H₂O₂ + O₂ determined agree very well with those reported by Kappel et al. (2002) [5]; the recommendation therefore remains unchanged: k₄ = 1.0 × 10¹⁴ exp(?5556/T) + 1.9 × 10¹¹⁺exp(709/T) [cm³ mol^?1 s^?1]. All the tests were performed near 1.7 atm.     

Advanced oxidation of Reactive Blue 181 solution: A comparison between Fenton and Sono-Fenton Process

In this work, the decolorization of C.I. Reactive Blue 181 (RB181), an anthraquinone dye, by Ultrasound and Fe²⁺ H₂O₂ processes was investigated. The effects of operating parameters, such as Fe²⁺ dosage, H₂O₂ dosage, pH value, reaction time and temperature were examined. Process optimisation [pH, ferrous ion (Fe²⁺), hydrogen peroxide (H₂O₂), and reaction time], kinetic studies and their comparison were carried out for both of the processes. The Sono-Fenton process was performed by indirect sonication in an ultrasonic water bath, which was operated at a fixed 35-kHz frequency. The optimum conditions were determined as [Fe²⁺] = 30 mg/L, [H₂O₂] = 50 mg/L and pH = 3 for the Fenton process and [Fe²⁺] = 10 mg/L, [H₂O₂] = 40 mg/L and pH = 3 for the Sono-Fenton process. The colour removals were 88% and 93.5% by the Fenton and Sono-Fenton processes, respectively. The highest decolorization was achieved by the Sono-Fenton process because of the production of some oxidising agents as a result of sonication. The paper also discussed kinetic parameters. The decolorization kinetic of RB181 followed pseudo-second-order reaction (Fenton study) and Behnajady kinetics (Sono-Fenton study).     

Photodiode properties of molecular beam epitaxial InSb on a heavily doped substrate

Photodiodes of InSb were fabricated on an epitaxial layer grown using molecular beam epitaxy (MBE). Thermal cleaning of the InSb (0 0 1) substrate surface, 2° towards the (1 1 1) B plane, was performed to remove the oxide. Photodiode properties of МВЕ-formed epitaxial InSb were demonstrated. Zero-bias resistance area product (R₀A) measurements were taken at 80 K under room temperature background for a pixel size of 100 μm × 100 μm. Values were as high as 4.36 × 10⁴ Ω/cm², and the average value of R₀A was 1.66 × 10⁴ Ω/cm². The peak response was 2.44 (A/W). The epitaxial InSb photodiodes were fabricated using the same process as bulk crystal InSb diodes with the exception of the junction formation method. These values are comparable to the properties of bulk crystal InSb photodiodes.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

Interaction of dioxouranium(VI) ion with EDTA at different ionic strengths

The formation of complex species of dioxouranium(VI) ion with EDTA was studied in the pH range of 1–3.5 and at 25 °C using a combination of potentiometric and spectrophotometric techniques. Results showed evidence for formation of the following species: [UO₂H₄EDTA]²⁺, [UO₂H₃EDTA]⁺, and [UO₂H₂EDTA]. Investigations were performed in sodium perchlorate as background electrolyte at 0.1, 0.3, 0.5, 0.7, and 1.0 mol dm^? 3. The parameters based on the formation constants were calculated, and the dependences of protonation and the stability constants on ionic strength are described. The dependence on ionic strength of the formation constants was analyzed using the specific ion interaction theory (SIT) model. The stability constant values at infinite dilution, obtained using SIT model, are log β°₁₄₁ = 6.77, log β°₁₃₁ = 5.99 and log β°₁₂₁ = 9.29, where indexes for the overall stability constant, β_pqr, refer to the equilibrium pUO₂²⁺ + qH⁺ + rL^4? ? M_pH_qL_r^{(2p + q ? 4r)}. The specific interaction coefficients are also reported.     

Studies on the effect of chlorides of magnesium,calcium, strontium and barium on the temperature of the sound velocity maximum of water

The effect of chlorides of magnesium, calcium, strontium and barium on the temperature of the sound velocity maximum (TSVM) of water, T_w, has been studied by determining the ultrasonic velocity using a single crystal variable path interferometer working at 3 MHz. The accuracy in ultrasonic velocity measurement is ± 0.05 m s^− 1. The ultrasonic velocity measurements were carried out at ≃ 2 °C intervals over a range of 5 °C to either side of TSVM of the solutions. The accuracy in fixing TSVM is ± 0.2 °C. The shifts in TSVM of water due to the addition of MgCl₂ and CaCl₂, (ΔT_obs), are found to be positive at low concentrations becoming maxima around the weight fraction w ≃ 2.3 × 10^− 2 for MgCl₂ and w ≃ 3.8 × 10^− 2 for CaCl₂ and becoming negative around w ≃ 5.6 × 10^− 2 for MgCl₂ and w ≃ 3.8 × 10^− 2 for CaCl₂. (ΔT_obs) for MgCl₂ > CaCl₂ > SrCl₂ > BaCl₂ indicating that the strength of the structural interactions in modifying the hydrogen-bonded structure of water is in the order Mg²⁺ > Ca²⁺ > Sr²⁺ > Ba²⁺. The results are explained in the light of the structural properties of the anions and cations in the solutions in modifying the three dimensional hydrogen-bonded structure of water.     

Radiation stability of M1 − xPrxF2 + x (M = Ca,Sr, Ba) crystals

The radiation stability of the mixed crystals M_1 ? xR_xF_2 + x (M = Ca, Sr, Ba) depends on types of the alkaline-earth and rare-earth ions. Different to Eu- and Ce-containing systems, M_1 ? xPr_xF_2 + x solid solutions have a low radiation resistance, which may be associated with hole trapping on praseodymium ion according to the reaction Pr³⁺ → Pr⁴⁺ which is typical for praseodymium. The coloration efficiency of M_1 ? xPr_xF_2 + x crystals grows in the row Ca → Sr → Ba, which is explained satisfactorily within the model of rare-earth clusters, the structure of which is determined by the ratio of the base alkaline-earth cation to the praseodymium ion radii.     

Modifications in physical,optical and electrical properties of tin oxide by swift heavy Au8+ ion bombardment

Tin oxide thin films were deposited by a novel technique called as modified-SILAR. The preparative parameters were optimized to obtain good quality thin films. As-deposited films were annealed in O₂ atmosphere for 1 h at 500 °C. The annealed films were irradiated using Au⁸⁺ ions with energy of 100 MeV at different fluencies of 1 × 10¹¹, 1 × 10¹², 5 × 10¹² and 1 × 10¹³ ions/cm² using tandem pelletron accelerator. The irradiation-induced modifications in tin oxide thin films were studied using XRD, AFM, optical band gap, photoluminescence and I–V measurements. XRD studies showed formation of tin oxide with tetragonal structure. AFM revealed uniform deposition of the material with increase in grain size after irradiation. Decrease in band gap from 3.51 eV to 2.82 eV was seen with increases in fluency. A decrease in PL intensity, and an additional peak was observed after irradiation. I–V measurements showed a decrease in resistance with fluency.     

The effect of chemical pressure in rutheno-cuprates

We have studied the effect of negative chemical pressure in the RuGd_1.5(Ce_0.5?xPr_x)Sr₂Cu₂O_10?δ with Pr content of 0.0 ? x ? 0.2. This is also investigated using the bond length results obtained from the Rietveld refinement analysis. The c parameter and cell volume increase with x for 0.0 ? x ? 0.15. The width of the resistivity transition also increases with Pr concentration, indicating higher inhomogeneity and oxygen deficiency. The difference in the ionic valences of Pr^3+,4+ and Ce⁴⁺ causing different hole doping, the difference in the ionic radii, and oxygen stoichiometry affect the superconducting transition. The magnetoresistance shows a cusp around 135 K which lies between the antiferromagnetic and ferromagnetic transition temperatures, which is probably due to the presence of a spin glass region. There exist two magnetic transition temperatures for 0.0 ? x ? 0.2 which respectively change from T_M = 155 K to 144 K and from T_irr = 115 K to 70 K. The magnetization versus applied magnetic field isotherms at 77 K and 300 K show that the remanent magnetization and coercivity are lower for samples with higher Pr content.     

Shock tube/laser absorption studies of the decomposition of methyl formate

Reaction rate coefficients for the major high-temperature methyl formate (MF, CH₃OCHO) decomposition pathways, MF → CH₃OH + CO (1), MF → CH₂O + CH₂O (2), and MF → CH₄ + CO₂ (3), were directly measured in a shock tube using laser absorption of CO (4.6 μm), CH₂O (306 nm) and CH₄ (3.4 μm). Experimental conditions ranged from 1202 to 1607 K and 1.36 to 1.72 atm, with mixtures varying in initial fuel concentration from 0.1% to 3% MF diluted in argon. The decomposition rate coefficients were determined by monitoring the formation rate of each target species immediately behind the reflected shock waves and modeling the species time-histories with a detailed kinetic mechanism [12]. The three measured rate coefficients can be well-described using two-parameter Arrhenius expressions over the temperature range in the present study: k₁ = 1.1 × 10¹³ exp(?29556/T, K) s^?1, k₂ = 2.6 × 10¹² exp(?32052/T, K) s^?1, and k₃ = 4.4 × 10¹¹ exp(?29 078/T, K) s^?1, all thought to be near their high-pressure limits. Uncertainties in the k₁, k₂ and k₃ measurements were estimated to be ±25%, ±35%, and ±40%, respectively. We believe that these are the first direct high-temperature rate measurements for MF decomposition and all are in excellent agreement with the Dooley et al. [12] mechanism. In addition, by also monitoring methanol (CH₃OH) and MF concentration histories using a tunable CO₂ gas laser operating at 9.67 and 9.23 μm, respectively, all the major oxygen-carrying molecules were quantitatively detected in the reaction system. An oxygen balance analysis during MF decomposition shows that the multi-wavelength laser absorption strategy used in this study was able to track more than 97% of the initial oxygen atoms in the fuel.     

The layered iron phosphate KMgFe(PO4)2: Crystal structure,Mössbauer spectroscopy and ionic conductivity

A new iron phosphate, KMgFe(PO₄)₂ has been synthesized and investigated by X-ray diffraction, Mössbauer spectroscopy and ionic conductivity. This compound crystallizes in the monoclinic space group C2/c with the parameters a = 18.529(7) Å, b = 5.402(3) Å, c = 9.374(9) Å, β = 120.64(5)° and Z = 4. Its original structure can be described as the stacking along the [101] direction of [MgFe(PO₄)^?₂]_∞ layers of corner-sharing MO₄ (M = 0.5 Fe + 0.5 Mg) and PO₄ tetrahedra. The K⁺ ions are occupying the inter-layer space. The Mössbauer spectroscopy confirms the occurrence of only tetrahedral Fe³⁺ ions and gives a definitive proof of the disordered character of their distribution. Ionic conductivity results obtained by the impedance spectroscopy technique show that this material is a two-dimensional ionic conductor, with low activation energy, 0.51 eV, that is interpreted on the basis of two-dimensional pathways.     

Birefraction of the LiNbO3 crystal in the infrared band

We proposed a spectrum method to determine birefraction of the sample. When the infrared incident light transmits in the birefraction direction of the cube crystal, because of the birefraction of the sample, the transmit spectrum appears interference fringes. The equation Δn = 1/[D(dυ/dm)] shows the relationship between the birefraction and the wave-number, with the interference-number of crystals in the infrared band at room temperature. Via the infrared transmitting along the x-axis of cube lithium niobate crystal, the interference fringes were found. By the fitted polynomial method, the relationship of the birefraction and the wave-number or wavelength of the lithium niobate crystal be educed, which is, Δn = 0.4149 ? 9.00174 × 10^?5υ + 5.64347 × 10^?9υ²,or n = 0.05366 ? 5.20334 × 10^?5λ + 3.99694 × 10^?8λ².     

Dissociation of dimethyl ether at high temperatures

The decomposition of dimethyl ether (CH₃OCH₃) has been investigated behind incident shock waves in a diaphragmless shock tube using laser schlieren densitometry, LS (T = 1500–2450 K, P = 57 ± 4, 125 ± 5 and 253 ± 12 Torr). The LS density gradient profiles were simulated and excellent agreement was found between the simulations and experimental profiles. Rate coefficients for CH₃OCH₃ → CH₃O + CH₃ were obtained. They showed strong fall-off, and at the lower end of the experimental temperature range are close to the low pressure limit. First order rate coefficient expressions were determined over 1500 < T < 2450 K. k_57Torr = (3.10 ± 1.0) × 10⁷⁹T^?19.03 exp(?54417/T) s^?1, k_125Torr = (1.12 ± 0.3) × 10⁸³T^?19.94 exp(?55554/T) s^?1and k_253Torr = (1.02 ± 0.3) × 10⁷³T^?17.09 exp(?51500/T) s^?1. The effect of a roaming channel for decomposition of dimethyl ether was assessed and the best agreement was obtained with 1% dissociation of DME via the roaming path.     

Bulk and surface properties of ionic salt CsH5(PO4)2

We report a comparative study of transport and thermodynamic properties of single-crystal and polycrystalline samples of the ionic salt CsH₅(PO₄)₂ possessing a peculiar three-dimensional hydrogen-bond network. The observed potential of electrolyte decomposition ≈ 1.3 V indicates that the main charge carriers in this salt are protons. However, in spite of the high proton concentration, the conductivity appears to be rather low with a high apparent activation energy E_a ≈ 2 eV, implying that protons are strongly bound. The transport anisotropy though is not large, correlates with the crystal structure: the highest conductivity is found in the [001] direction (σ_130 °C ∼ 5.6 × 10^− 6 S cm^− 1) while the minimal conductivity is in the [100] direction (σ_130 °C ∼ 10 ⁻⁶ S cm^− 1). The conductivity of polycrystalline samples appears to exceed the bulk one by 1–3 orders of magnitude with a concomitant decrease of the activation energy (E_a ≈ 1.05 eV), which indicates that a pseudo-liquid layer with a high proton mobility is formed at the surface of grains. Infrared and Raman spectroscopy used to study the dynamics of the hydrogen-bond system in single-crystal and polycrystalline samples have confirmed the formation of such a modified surface layer in the latter. However, no bulk phase transition into the superionic disordered phase is observed in CsH₅(PO₄)₂ up to the melting point T_melt ∼ 151.6 °C, in contrast to its closest relative compound CsH₂PO₄.     

Photoionization studies of the atmospherically important species N and OH at the Elettra synchrotron radiation source

In this paper angularly resolved photoelectron spectra (PES) and constant-ionic-state (CIS) spectra are presented for the atmospherically important species N and OH.The natural width Γ, line shape parameters q and ρ² and discrete oscillator strengths f have been measured for the members of the N*[2s2p³(⁵S), np] (⁴P) ← N(⁴S) autoionizing resonances for n = 5–10. The n = 5 parameters calculated in this work are in good agreement with the values obtained previously whereas for the resonances with n = 6–10 the values of these parameters are reported for the first time. The asymmetry parameter (β) for the first band of N atoms, the N⁺(³P) ← N(⁴S) ionization, has also been measured in the photon energy range of the above autoionizing resonances.For OH, CIS spectra have been recorded for the first photoelectron band corresponding to the ionization OH⁺(X³Σ⁻, v⁺ = 0) ← OH(X²Π, v″ = 0). In these spectra, rotationally partially resolved bands associated with OH*(a¹Δ3d, v′ = 0) ← OH(X²Π, v″ = 0) resonances have been observed. Suggestions for their assignment are made on the basis of their positions and band simulations which use rotational line strength calculations.