Spray deposited amorphous RuO2 for an effective use in electrochemical supercapacitor

The structural, surface morphological and optical properties of sprayed ruthenium oxide thin film were investigated using XRD, SEM and optical absorption measurements. The structural analysis from XRD pattern showed the formation of RuO₂ in amorphous phase. The scanning electron micrographs revealed network-like morphology of ruthenium oxide. The optical studies showed a direct band gap of 2.4 eV for ruthenium oxide films. Ruthenium oxide thin film exhibited a cyclic voltammogram indicative high reversibility of a typical capacitive behavior in 0.5 M H₂SO₄ electrolyte. A specific capacitance of 551 F/g was obtained with ruthenium oxide thin film (electrode) prepared by spray pyrolysis method. The specific capacitances of 551 and 450 F/g at the scan rate of 5 and 125 mV/s, respectively, indicate that the capacitance value varies inversely with scan rate.     

High-surface-area microporous carbon as the efficient photocathode of dye-sensitized solar cells

This paper reports on the application of cornstalks-derived high-surface-area microporous carbon (MC) as the efficient photocathode of dye-sensitized solar cells (DSCs). The photocathode, which contains MC active material, Vulcan XC–72 carbon black conductive agent, and TiO₂ binder, was obtained by a doctor blade method. Electronic impedance spectroscopy (EIS) of the MC film uniformly coated on fluorine doped SnO₂ (FTO) glass displayed a low charge-transfer resistance of 1.32 Ω cm². Cyclic voltammetry (CV) analysis of the as-prepared MC film exhibited excellent catalytic activity for I₃^?/I^? redox reactions. The DSCs assembled with the MC film photocathode presented a short-circuit photocurrent density (J_sc) of 14.8 mA cm^?2, an open-circuit photovoltage (V_oc) of 798 mV, and a fill factor (FF) of 62.3%, corresponding to an overall conversion efficiency of 7.36% under AM 1.5 irradiation (100 mW cm^?2), which is comparable to that of DSCs with Pt photocathode obtained by conventional thermal decomposition.     

Adsorption of 2,2′-bipyridine at an Au(111)|ionic liquid electrified interface

The adsorption of added 2,2′-bipyridine (2,2′-BP) from 1-ethyl-2,3-dimethyl imidazolium bis(trifluoromethanesulfonyl)imide (EMMImNTf₂) at an Au(111) electrode has been investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Addition of 2,2′-BP to the ionic liquid clearly modifies the interfacial region as a result of the competition between 2,2′-BP and EMMImNTf₂ to occupy the electrode surface. Within the region of ideal polarizability, the 2,2′-BP adlayer undergoes structural changes, shown by the presence of peaks in the CV curves. Between −0.2 V and + 0.9 V, the capacitance–potential curves obtained from EIS data present a capacity maximum depending strongly on the ac frequency, which is typical pseudo-capacitive behavior indicative of a reorganization of the interfacial layer. At more positive potentials a true capacity value close to 10 μF.cm^− 2 and invariant with the potential suggests that the 2,2′-BP molecules adopt a perpendicular orientation with the nitrogen atoms facing the electrode surface, similar to their adsorption on gold from aqueous solutions.     

Electrodeposited PbO2 thin film on Ti electrode for application in hybrid supercapacitor

PbO₂ thin films were prepared by pulse current technique on Ti substrate from Pb(NO₃)₂ plating solution. The hybrid supercapacitor was designed with PbO₂ thin film as positive electrode and activated carbon (AC) as negative electrode in the 5.3 M H₂SO₄ solution. Its electrochemical properties were determined by cyclic voltammetry (CV), charge–discharge test and electrochemical impedance spectroscopy (EIS). The results revealed that the PbO₂/AC hybrid supercapacitor exhibited large specific capacitance, high-power and stable cycle performance. In the potential range of 0.8–1.8 V, the hybrid supercapacitor can deliver a specific capacitance of 71.5 F g^?1 at a discharge current density of 200 mA g^?1(4 mA cm^?2) when the mass ratio of AC to PbO₂ was three, and after 4500 deep cycles, the specific capacitance remains at 64.4 F g^?1, or 32.2 Wh Kg^?1 in specific energy, and the capacity only fades 10% from its initial value.     

Correlation between capacitances of porous carbons in acidic and aprotic EDLC electrolytes

A study based on a total of 41 nanoporous carbons shows that there exists a good correlation between the limiting gravimetric capacitances C_o at low current densities j (1 mA cm⁻²) measured in aprotic (1 M (C₂H₅)₄NBF₄ in acetonitrile) and in acidic (2 M aqueous H₂SO₄) electrolytes. The comparison of the surface-related capacitances (F m⁻²) of well characterized samples with the amount of thermodesorbed CO suggests a strong contribution of CO generating surface groups to charge storage in the acidic electrolyte, but a negligible contribution in the aprotic medium. It also appears that the decrease of the capacitance with current density is similar in both electrolytes. This confirms that the average micropore width and the CO₂ generating surface groups are the main factors which limit the ionic mobility in both electrolytes.     

Hysteresis in the measurement of double-layer capacitance at the gold–ionic liquid interface

The capacitance of the polycrystalline gold electrode–ionic liquid BMIMTf [1-butyl-3- methyl imidazolium trifluoromethanesulfonate (triflate)] interface has been studied using ac voltammetry and electrochemical impedance spectroscopy (EIS). Slow potential scanning reveals a massive hysteresis between potential scans toward negative or positive directions and provides a distorted C(E) curve. Kinetic studies indicate that 10 min wait times are required after each potential step for system relaxation. EIS resolves the overall series capacitance into contributions from ion adsorption and double-layer capacitance, C_DL. Isolation of C_DL reveals that even 10 min of equilibration time is insufficient to completely remove the hysteresis. The shape of the negative-going C_DL(E) curve is camel-shaped whereas the shape of the positive-going curve is bell-shaped.     

A study of ion charge transfer on electrochemical behaviors of poly(vinylidene fluoride)-derived carbon electrodes

In this work, porous carbon with a high specific surface area as electrode materials for supercapacitors are obtained by a carbonization process at various temperatures from 700 °C to 1000 °C without activation process using poly(vinylidene fluoride) (PVDF) as a carbon precursor. The electrochemical performance is characterized by cyclic voltammetry and galvanostatic charge–discharge cycling performance using two-electrode system in 6.0 M KOH as an aqueous electrolyte. The results indicate that carbonization temperature significantly affected the specific surface area and pore volume of the PVDF-derived carbons and their capacitive behavior. In particular, the electrochemical performance of the prepared PVDF-derived carbon is determined by both the electric double-layer capacitance and the pseudo-capacitance resulting from the residual surface functional groups on PVDF-derived carbons.     

Measurements of differential capacitance in room temperature ionic liquid at mercury,glassy carbon and gold electrode interfaces

Differential capacitances were measured in 1-propyl-3-methylimidazolium tetrafluoroborate (PMIBF₄) ionic liquid at three different electrode substrates (Hg, GC (glassy carbon) and Au) as a function of potential. Essentially different capacitance–potential curves were obtained at different electrodes. From the parabolic electrocapillary curve measured at dropping Hg electrode in PMIBF_4, the potential of zero charge (PZC) was found to be −0.31 V vs. Ag/AgCl (wire). However, the capacitance–potential curve at Hg electrode was found not to show any valley related to the PZC, whereas at GC and Au electrodes a minimum was observed at 0.29 and −0.51 V, respectively. The results are in disagreement with the recent theoretical study which implies that the capacitance–potential curve should be of bell shape with the maximum value of capacitance at PZC. The parabolic capacitance–potential curve similar to those obtained in inorganic molten salts was also observed for the first time at GC electrode. Probable causes of the difference in their capacitance–potential curves were also discussed.     

Electrochemical supercapacitor application of pervoskite thin films

We have explored electrochemically deposited pervoskite nanocrystalline porous bismuth iron oxide (BiFeO₃) thin film electrode from alkaline bath for electrochemical supercapacitors. The pervoskite BiFeO₃ nanocrystalline thin film electrode showed comparable specific capacitance of 81 F g⁻¹ and electrochemical supercapacitive performance and stability in an aqueous NaOH electrolyte to that of commonly used ruthenium based pervoskites.     

Heavy metals and color retention by a synthesized inorganic membrane

In this study, a new type of a double-layer ceramic membrane was used for the filtration of wastewater. The synthesized membrane consists of a macroporous substrate (with pore size of about 0.1 μm) prepared following the colloid filtration technique and a thin film functional layer (with pore size of about 10 nm) carried out according to the sol–gel preparation method.The ceramic membranes were tested for the removal of cadmium, zinc, Methylene Blue and Malachite Green from water under a pressure of 5 bar and a treatment time of 2 h. Liquid filtration and flow tests through these membranes resulted in a rejection rate of 100% for Methylene Blue and Malachite Green. This paper also presents the ability of the tubular membrane prepared to separate heavy metals (cadmium and zinc) from their synthetic aqueous solutions. The influence of the applied pressure, feed solute concentration, feed pH on the rejection of cadmium and zinc ions was studied. Retention rates of cadmium and zinc ions of 100% were observed for an initial feed concentration of 10⁻⁴ mol/L.     

Preparation of hexagonal nanoporous nickel hydroxide film and its application for electrochemical capacitor

Nanoporous nickel hydroxide film has been successfully electrodeposited on titanium substrate from nickel nitrate dissolved in the aqueous domains of the hexagonal lyotropic liquid crystalline phase of Brij 56. Low-angle X-ray diffraction (XRD), transmission electron microscopy (TEM), and atomic force microscopy (AFM) studies show that the film has a regular nanostructure consisting of a hexagonal array of cylindrical pores with a repeat center-to-center spacing of about 7 nm. Preliminary electrochemical studies are carried out using cyclic voltammetry (CV) and chronopotentiometry technology. A maximum specific capacitance of 578 F g⁻¹ could be achieved for the nanoporous Ni(OH)₂ film electrode, suggesting its potential application in electrochemical capacitors.     

Double-layer capacitance of waste coffee ground activated carbons in an organic electrolyte

Using ZnCl₂ activation we prepared a series of carbon electrodes from waste coffee grounds to study the effect of mesopores on double-layer capacitance in a tetraethyl ammonium tetrafluoroborate/acetonitrile electrolyte. The activated carbon with the largest mesopore volume achieved an energy density of 34 Wh kg^?1 at low current loads, and significantly retained an energy density of 16.5 Wh kg^?1 and specific capacitance of more than 100 F g^?1 at fast charge–discharge rates (20 A g^?1). The effect of mesopores on capacitance at fast charge–discharge rates is discussed.     

A new method for detection of endotoxin on polymyxin B-immobilized gold electrodes

Endotoxin can lead to irreversible shock and death, underlying the necessity for development of facile, rapid, sensitive and in situ methods to detect endotoxin. We used electrochemical impedance spectroscopy (EIS) to detect interaction of endotoxin with polymyxin B (PmB) immobilized on 4,4-dithiodibutyric acid coated gold electrodes. An equivalent circuit model with a constant phase element was used to interpret the obtained impedance spectra. The results indicated that the gold electrode after electrochemical polishing pretreatment in both 2-(N-Morpholino) ethanesulfonic acid (MES) and HClO₄ solutions had a more effective surface state than that treated in H₂SO₄ solution. The changes in capacitance associated with a constant phase element on the PmB-modified electrodes were more sensitive, compared to those in the charge-transfer resistance, for detecting endotoxin over the 0.2–0.8 ng/mL concentrations. The activated and modified gold electrodes might be used to EIS detect endotoxin in real-time.     

Nitrogen enriched mesoporous carbon spheres obtained by a facile method and its application for electrochemical capacitor

A kind of mesoporous carbon spheres (MCS) containing in-frame incorporated nitrogen has been prepared by a facile polymerization-induced colloid aggregation method. As the electrode material for electric double layer capacitor (EDLC) in 5 mol/L H₂SO₄, the MCS products present excellent specific capacitance as 211 F/g much larger than that of the most popularly applied activated carbon at a high discharge current density of 1 A/g. Its specific capacitance can still remain 200 F/g at 20 A/g. The superior electrochemical performance of MCS is associated with the following characteristics: high specific surface area (∼1330 m²/g) contributed mainly by the mesopores, uniform pore size as large as 29 nm and moderate content of nitrogen (10 wt%), which are the requirements for ideal supercapacitors.     

Electropolymerizing polyaniline on undoped 100 nm diamond powder and its electrochemical characteristics

Conductive polyaniline (PANI) was electropolymerized on undoped 100 nm diamond powders in sulphuric acid solution containing aniline to improve the conductivity and the electrochemistry of the nano- or submicro-scaled diamond particles. Cyclic voltammetry (CV) experiment was carried out at an upper potential of 1.1 V in initial sweeps and a potential range of ?0.2–0.9 V for the growth of PANI on a diamond powder electrode. Field emission-scanning electron microscope (FESEM) result reveals that the diamond particles were well coated by PANI films with globular or fibroid surface morphology. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were employed to investigate the electrochemical properties of the PANI/diamond composite electrode. It presents lower resistance and better capacitance than the pristine diamond powder.     

Electrochemical investigation of corrosion and corrosion inhibition of iron in hydrochloric acid solutions

The inhibition effect of 1-methyl pyrazole (MPA) on the acidic corrosion of iron in 1.0 M HCl was studied at different concentrations (10^?3–10^?2 M) by potentiodynamic polarization and electrochemical impedance spectroscopy, and EIS measurements. It is found from the polarization studies that methyl pyrazole (MPA) behaves mainly as anodic inhibitor in HCl. Values of polarization resistance (R_p) and double layer capacitance (C_dl) in the absence and presence of MPA in 1.0 M HCl are determined. The adsorption of MPA on iron surface from HCl is found to obey Temkin adsorption isotherm.     

An SFG/DFG investigation of CN− adsorption at an Au electrode in 1-butyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl) amide ionic liquid

In this paper we report an SFG/DFG investigation of the adsorption of CN^? – used as a probe molecule to study the electrochemical double-layer structure – at a polycrystalline Au electrode in 1-butyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl) amide ([BMP][TFSA]) room-temperature ionic liquid (RTIL). The adsorption of CN^? yielded single SFG and DFG bands in the range from ca. 2125 to 2135 cm^?1, exhibiting a Stark tuning of ca. 3 cm^?1 V^?1. Vibrational resonances – corresponding to modes of the RTIL coadsorbed with CN^?, were found in the range from ca. 1200 to 1500 cm^?1. The study of the double-layer structure was complemented by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements, from which the differential double-layer capacity (C_DL) was estimated.     

An acidic cellulose–chitin hybrid gel as novel electrolyte for an electric double layer capacitor

A novel acidic cellulose–chitin hybrid gel electrolyte including binary ionic liquids (ILs) with an aqueous H₂SO₄ solution was prepared for an electric double layer capacitor (EDLC). Its electrochemical characteristics were investigated by galvanostatic charge–discharge measurements. The test cell with a hybrid gel electrolyte shows a specific capacitance of 162 F g^?1 at room temperature, which is higher than that for a cell with an H₂SO₄ electrolyte, 155 F g^?1. This hybrid gel electrolyte exhibits excellent high-rate discharge capability in a wide range of current densities as well as an aqueous H₂SO₄ solution. The discharge capacitance of the test cell can retain over 80% of its initial value in 100,000 cycles even at a high current density of 5000 mA g^?1.     

Electrodeposition of MnO2 nanowires on carbon nanotube paper as free-standing,flexible electrode for supercapacitors

MnO₂ nanowires were electrodeposited onto carbon nanotube (CNT) paper by a cyclic voltammetric technique. The as-prepared MnO₂ nanowire/CNT composite paper (MNCCP) can be used as a flexible electrode for electrochemical supercapacitors. Electrochemical measurements showed that the MNCCP electrode displayed specific capacitances as high as 167.5 F g⁻¹ at a current density of 77 mA g⁻¹. After 3000 cycles, the composite paper can retain more than 88% of initial capacitance, showing good cyclability. The CNT paper in the composite acted as a good conductive and active substrate for flexible electrodes in supercapacitors, and the nanowire structure of the MnO₂ could facilitate the contact of the electrolyte with the active materials, and thus increase the capacitance.     

Controlled synthesis of MnSn(OH)6/graphene nanocomposites and their electrochemical properties as capacitive materials

We report the synthesis of novel MnSn(OH)₆/graphene nanocomposites produced by a co-precipitation method and their potential application for electrochemical energy storage. The hydroxide decorated graphene nanocomposites display better performance over pure MnSn(OH)₆ nanoparticles because the graphene sheets act as conductive bridges improving the ionic and electronic transport. The crystallinity of MnSn(OH)₆ nanoparticles deposited on the surface of graphene sheets also impacts the capacitive properties as electrodes. The maximum capacitance of 31.2 F/g (59.4 F/g based on the mass of MnSn(OH)₆ nanoparticles) was achieved for the sample with a low degree of crystallinity. No significant degradation of capacitance occurred after 500 cycles at a current density of 1.5 A/g in 1 M Na₂SO₄ aqueous solution, indicating an excellent electrochemical stability. The results serve as an example demonstrating the potential of integrating highly conductive graphene networks into binary metal hydroxide in improving the performance of active electrode materials for electrochemical energy storage applications.