微波消解-ICP-MS法测定硫磺中18种微量元素

建立了用微波消解-电感耦合等离子体质谱法(ICP-MS)同时测定硫磺中18种微量元素(锂、镁、铝、钙、钒、铬、锰、铁、钴、镍、铜、锌、镉、砷、硒、钡、铅和汞)的定量分析方法。通过对消解所用试剂及条件进行研究,确定最佳的样品处理条件;为了获得最佳的信噪比并降低光谱干扰,研究采用单变量方法,对ICP-MS的射频功率和雾化气体流量等因素进行了性能优化。结果显示：该方法各元素的校准曲线线性相关系数在0.999以上,所有元素的检出限(LODs) 在0.001-0.962 mg/Kg之间,测定下限范围在0.004-3.85 mg/Kg之间,回收率在82.9 %~115 %之间,相对标准偏差均小于3 %。     

Irradiation techniques for the release of bound heavy metals in natural waters and blood

Irradiation techniques are compared with conventional acid digestion procedures for the release of bound heavy metals in natural waters and in blood, before their determination by anodic stripping voltammetry. Ultra-violet irradiation of acidified water with a 550-W mercury vapour lamp releases bound zinc, cadmium, lead and copper after 4 h. The same results can be achieved with a 30-Mrad dose of high-energy γ-irradiation. These techniques are also effective for the release of metals in whole blood and blood plasma, where sample volumes as small as 200 μl are adequate in analyses for zinc, copper and lead. By comparison with acid digestion and solvent extraction methods, irradiation treatments offer the advantages of minimum sample manipulation and negligible reagent blanks.     

微波消解-电感耦合等离子体原子发射光谱(ICP-AES)法测定含铜污泥中多种重金属

为了填补现有方法的技术空白,本方法采用微波消解和电感耦合等离子体原子发射光谱法（ ICP-AES）相结合,实现对含铜污泥中铅、锌、铬、镉、砷、镁、铝、锑量的同时测定。首先采用盐酸-硝酸-氢氟酸微波消解进行样品的前处理,消解后加入高氯酸置于电热板进行除碳并赶酸,溶样效果理想,且有效避免了高温溶样对易挥发元素砷、锑的损失,整个过程安全、高效、无损。溶样后以电感耦合等离子体发射光谱法（ ICP-AES）进行测定。对含铜污泥的分解方法进行了合理选择,并对测定时的元素分析谱线及各测定元素间干扰情况等进行了讨论。该方法的加标回收率在95.31%~107.28%%,相对标准偏差（RSD）在0.31%~2.05%之间（n=7),结果表明,该方法准确度高,操作简单快捷,可同时测定多种元素,能满足批量的测定含铜污泥中铅、锌、镍、铁、镉、铬、砷、锑含量的测定要求。     

Removal of exogenously bound elements from human hair by various washing procedures and determination by inductively coupled plasma mass spectrometry

A review of the literature shows that a variety of washing procedures to remove external contamination from hair have been proposed, but as yet no standardised procedures are available. In this study, methods for the pre-treatment and determination of antimony, arsenic, cadmium, chromium, lead, mercury and selenium in human hair by inductively coupled plasma mass spectrometry (ICP-MS) are developed.Investigations of various washing procedures to remove external contaminants show that in unexposed hair samples cadmium, lead and mercury are significantly removed from hair using a 0.1 M HCl wash, with 87, 73 and 5%, respectively being washed-off. The removal of antimony, arsenic and chromium from unexposed hair is, however, more efficient with 1% (v/v) sodium lauryl sulphate (SLS), with 43, 40 and 13% of each element, respectively being washed-off. Selenium is not removed from the hair by any of the washing methods studied. For the digestion of hair samples a digestion mixture of nitric acid and hydrogen peroxide is used.Experiments with simulated sweat spiked with each of these elements show that exogenously bound chromium, cadmium and lead are removed after washing with 0.1 M HCl. In contrast, antimony, arsenic, selenium and mercury irreversibly bind and, thus, are not removed with any of the washing solutions investigated. This work also compares hair levels of these elements in an unexposed and exposed group using the method developed.     

Determination of mobile form contents of Zn, Cd, Pb and Cu in soil extracts by combined stripping voltammetry

The amount of mobile forms of Zn, Pb, Cd and Cu in extracts obtained by treating soil samples with ammonium nitrate were determined by an appropriate combination of anodic and cathodic stripping voltammetry with hanging mercury drop electrode. Every analysis required three mercury drops: on the first one, zinc was determined; on the second, cadmium and lead; on the third, copper was determined. Zinc, lead and cadmium were determined by conventional differential-pulse anodic stripping voltammetry. For copper determination, adsorptive differential-pulse cathodic stripping voltammetry with amalgamation using chloride ions as a complexing agent was applied. The standard deviation of the results was from 1 to 10% depending on the metal content in the sample. Voltammetric results were in good agreement with the AAS analysis. No microwave digestion of soil extracts was necessary.     

Cathodic stripping voltammetric determination of selenium(IV) at a thin-film mercury electrode in a thiocyanate-containing electrolyte

The well-known method for the determination of selenium(IV), which is based on the cathodic stripping voltammetry of copper(I) selenide, has been adapted for application at the thin-film mercury electrode on glassy carbon (TFME). Insufficient reproducibility and sensitivity have been overcome by using a 0.1 mol/L HClO₄ electrolyte solution containing 0.02 mol/L thiocyanate ions. Thiocyanate ions have been found to increase the peak height of the selenium response and shift it to more positive potentials. This behaviour is explained by an adsorption of SCN^– at the interface glassy carbon/Cu₂Se and its action as an electron transfer catalyst between glassy carbon and copper(I) selenide. A 3σ-detection limit of 75 ng/L Se^(IV) has been achieved. The relative standard deviation is 5.2% at 5 μg/L selenium(IV). The influence of cadmium(II), arsenic(III), zinc(II), iron(III) and lead(II) ions on the selenium response has been studied. In case of lead ions, a new signal occurred at more negative potentials than the reduction of Cu₂Se. This signal, which is probably due to the reduction of PbSe, can also be used for the determination of selenium(IV).     

Direct analysis of solids for trace elements by combined electrothermal furnace/quartz T-tube/flame atomic absorption spectrometry

The analysis of solid samples by a combined graphite-furnace/air-acetylene flame technique based on generally available atomic absorption instrumentation is described. Samples are injected into the furnace and atomized via a slotted T-tube in the flame. Non-specific absorption is greatly reduced compared to that obtained in graphite-furnace atomic absorption spectrometry (a.a.s.). Sensitivity is reduced by 10–200 times compared to the direct graphite-furnace method, so that large sample sizes (up to 0.2 g) can be used; this minimizes problems caused by sample inhomogeneity. The elements considered are cadmium, lead, copper, arsenic, cobalt, mercury, antimony and selenium. Volatile elements such as mercury and arsenic can be determined without the need for a char step. Simple calibration procedures are possible in some cases and the precision is usually better than 10%. Background reduction capabilities are compared with those of conventional graphite-furnace a.a.s., the isothermal-furnace and the hollow graphite T-tube techniques. Analytical capabilities and results are presented for the direct determination of trace elements in numerous biological and some geological samples.     

Cathodic stripping voltammetric determination of selenium(IV) at a thin-film mercury electrode in a thiocyanate-containing electrolyte

The well-known method for the determination of selenium(IV), which is based on the cathodic stripping voltammetry of copper(I) selenide, has been adapted for application at the thin-film mercury electrode on glassy carbon (TFME). Insufficient reproducibility and sensitivity have been overcome by using a 0.1 mol/L HClO₄ electrolyte solution containing 0.02 mol/L thiocyanate ions. Thiocyanate ions have been found to increase the peak height of the selenium response and shift it to more positive potentials. This behaviour is explained by an adsorption of SCN^– at the interface glassy carbon/Cu₂Se and its action as an electron transfer catalyst between glassy carbon and copper(I) selenide. A 3σ-detection limit of 75 ng/L Se^(IV) has been achieved. The relative standard deviation is 5.2% at 5 μg/L selenium(IV). The influence of cadmium(II), arsenic(III), zinc(II), iron(III) and lead(II) ions on the selenium response has been studied. In case of lead ions, a new signal occurred at more negative potentials than the reduction of Cu₂Se. This signal, which is probably due to the reduction of PbSe, can also be used for the determination of selenium(IV). Received: 13 November 1996 / Revised: 19 December 1996 / Accepted: 24 December 1996     

Optimization of microwave digestion for mercury determination in marine biological samples by cold vapour atomic absorption spectrometry

Optimization of acid digestion method for mercury determination in marine biological samples (dolphin liver, fish and mussel tissues) using a closed vessel microwave sample preparation is presented. Five digestion procedures with different acid mixtures were investigated: the best results were obtained when the microwave-assisted digestion was based on sample dissolution with HNO3-H2SO4-K2Cr2O7 mixture. A comparison between microwave digestion and conventional reflux digestion shows there are considerable losses of mercury in the open digestion system. The microwave digestion method has been tested satisfactorily using two certified reference materials. Analytical results show a good agreement with certified values. The microwave digestion proved to be a reliable and rapid method for decomposition of biological samples in mercury determination.     

Ultraviolet irradiation and polarographic adsorptive complex wave techniques for the simple and rapid simultaneous determination of trace amounts of zinc,lead and copper in human hair

Polarographic adsorptive complex waves in the presence of catechol violet were studied for the simple and rapid simultaneous determination of traces of zinc, lead and copper in human hair and UV irradiation techniques were compared with conventional acid digestion procedures. UV irradiation of acidified hair with a 500-W mercury are lamp releases bound zinc, lead and copper after 3 h. Compared with the acid digestion procedure, the blank of the UV irradiation method is lower, the amounts of reagents used are smaller and the sample manipulations are simpler. The mechanisms of the polarographic adsorptive complex waves of Zn-, Pb-Cu- catechol violet are discussed.     

Comparison of four microwave digestion methods for the determination of selenium in fish tissue by using hydride generation atomic absorption spectrometry

Four microwave digestion methods of fish tissue for selenium determination by hydride generation atomic absorption spectrometry were compared, in which potassium hexacyanoferrate(III) was chosen as a masking agent for eliminating matrix interferences. The results showed that the methods employing HNO(3)/H(2)O(2), HNO(3)/K(2)S(2)O(8)/H(2)O(2) and HNO(3)/H(3)PO(4)/H(2)O(2) digestion media were unreliable. However, the decomposition using the digestion media of HNO(3)/H(2)SO(4)/H(2)O(2) enabled adequate digestion of fish tissue and retention of selenium in a state amenable for determination. Therefore, the digestion procedures with HNO(3)/H(2)SO(4)/H(2)O(2) media are proposed for the determination of selenium in fish tissue by hydride generation atomic absorption spectrometry. The recoveries of the spiked samples investigated ranged from 90 to 102%. The result obtained from analyzing the NIES CRM No. 6 mussel was in good agreement with the reference value (reference value: 1.5 mug/g; found: 1.45 +/- 0.05 mug/g). The limit of detection for selenium was 0.03 mug/g dry mass for a 100 mg sample. The contents of selenium in local fish species investigated ranged from 0.49 to 2.90 mug/g, and the relative standard deviation for the determination of selenium was less than 8%.     

Spectrophotometric determination of lithium with Quinizarin in drugs and serum

An endemic peripheral vascular disorder resulting in gangrene of the lower extremities, especially of the feet, is called 'Blackfoot disease (BFD)'. Clinically, the symptoms and signs of Blackfoot disease are similar to those of Buerger's disease. In this study, the objective is to examine the amount of arsenic, mercury, zinc, lead, and selenium in urine samples from BFD patients. After pre-treatment with acids, the samples were digested by means of a microwave oven. The determination of arsenic mercury, zinc, lead and selenium were by hydride atomic absorption spectrometry (HAAS), cold vapor atomic absorption spectrometry (CVAAS), flame atomic absorption spectrometry (FAAS), graphite furnace absorption spectrometry (GFAAS), respectively. The results indicated that urinary arsenic, mercury and lead of the BFD patients were significantly higher than those of the normal controls, while urinary zinc and selenium were significantly lower than those of the normal controls. The possibility that these elements are involved in the etiology of diseases is discussed.     

Concentrations of hazardous heavy metals in environmental samples collected in Xiamen, China, as determined by vapor generation non-dispersive atomic fluorescence spectrometry.

Non-dispersive atomic fluorescence spectrometry (NDAFS) coupled with vapor generation (VG) sample introduction was applied to the determination of the concentrations of hazardous heavy metals, such as arsenic, cadmium, lead and mercury, in seawater, soils and total airborne particulate matter (PM) collected around the Xiamen area in China. Almost 100% sample introduction efficiency was achieved by using thiourea and ascorbic acid for the pre-reduction of As(V) to As(III), K3Fe(CN)6 and tartaric acid for pre-oxidation of Pb(II) to Pb(IV), and masking the interferences arising from the co-existing transition metals to As, Cd, Hg and Pb during their vapor generation process. Moreover, a novel sample pretreatment device was developed to avoid the loss of mercury, lead, cadmium and arsenic during sample pretreatment. With such methods, the detection limit (DL) of arsenic, cadmium, lead and mercury was down to 0.08, 0.03, 0.05, 0.01 ng mL(-1) (3sigma), respectively. The relative standard deviations (RSD, n = 11) for arsenic, cadmium, lead and mercury at 10 ng mL(-1) were 0.9%, 1.6%, 1.3% and 2.0%, respectively. The concentrations of hazardous heavy metals in the environmental samples collected in Xiamen, China are in the range from 0.02 +/- 0.001 ng mL(-1) in seawater to 15.3 +/- 0.2 microg g(-1) in soils. Besides flame/GF-AAS and ICP-AES/MS, VG-NDAFS should be another choice for the determination of hazardous heavy metals in environmental samples.     

Application of Total Reflection X-Ray Fluorescence Spectrometry in the Textile Industry

 In the present study, the determination of arsenic, lead, cadmium, chromium, cobalt, copper, nickel, mercury and zinc in various cloth samples produced in Kayseri-Turkey was performed after extraction with artificial sweat solution and decomposition with nitric acid. TXRF is shown to be suitable for the determination of 7 trace elements, down to the 0.001 (cobalt) to 0.004 (copper) mg/kg level in textile extract except for mercury and cadmium. The extractable part of the toxic metals by artificial sweat solution is relatively low. In a few extracts the concentration values of Pb and Ni have exceeded their critical values of 0.2 mg/kg for lead and 1.0 mg/kg for nickel given by ?ko-Tex and determined for babys cloths. In addition, it was observed that the element pattern of textile samples resembled ‘finger print type’, TXRF-spectra. This technique can also be used for the identification of textile sample in forensic investigation. Received April 16, 2001 Revision October 1, 2001.     

Determination of selenium, zinc and cadmium in antidandruff shampoos by atomic spectrometry after microwave assisted sample digestion

Microwave assisted pre-treatments for atomic spectrometric determination (inductive coupled plasma-optical emission spectrometry, ICP-OES or flame atomic absorption spectrometry, FAAS) of metallic elements, usually present in antidandruff shampoos, are proposed. They are based on the digestion of the sample with HNO₃ into a closed reactor, which is irradiated at 800 W for a few minutes. Selenium was determined by ICP-OES. The limit of detection was 0.11 mg l⁻¹; the relative standard deviation (R.S.D.) for the selenium content in the samples was in the 0.6–3.6% range. The results obtained were in agreement with the label contents and the recovery of the proposed method was in the 100–106% range. Zinc and cadmium were determined by FAAS. The limit of detection for zinc determination was 0.078 mg l⁻¹; the R.S.D. for zinc contents was in the 0.8–8.6% range. A limit of detection of 0.09 mg l⁻¹ was obtained for cadmium determination; the R.S.D. for cadmium contents was in the 0.7–2.7% range. The determinations were performed after two different sample mineralization pre-treatments — dry ashing (in an electric furnace) and wet mineralization (in a microwave oven). Both methodologies provided comparable results for zinc and cadmium determination in shampoos. The proposed microwave assisted digestion procedures allow a precise and accurate determination of selenium, zinc and cadmium in commercial antidandruff shampoos, and the sample pre-treatment is less time-consuming than the classic methods.     

电感耦合等离子体原子发射光谱(ICP-AES)法测定再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝

采用硝酸、盐酸、氢氟酸(氟化氢铵)、高氯酸分解样品,电感耦合等离子体原子发射光谱法测定了再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝的量。其测定范围:ω(Cu):0.01%～0.60%;ω(Pb):0.10%～5.00%;ω(Fe):0.10%～5.00%;ω(In):0.0100%～0.200%;ω(Cd):0.010%～3.00%;ω(As):0.10%～2.00%;ω(Ca):0.10%～10.00%;ω(Al):0.10%～4.00%。各元素的加标回收率为93%～113%。方法准确、快速、可靠,适用于再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝量的同时测定。     

Potentiometric stripping analysis for zinc,cadmium. lead and copper in sea water

Analytical procedures for the determination of zinc(II), cadmium (II), lead(II) and copper(II) in sea water by potentiometric stripping analysis are described. The results are compared with those obtained by a combined solvent extraction-atomic absorption method both in the laboratory and on-board ship. The detection limits for zinc, cadmium, lead and copper are 0.03, 0.03, 0.01 and 0.02 μg l^-1, respectively, for a total analysis time of about 75 min. A very thin mercury film is useful in the determination of lead and copper.     

Trace Metal and Persistent Organochlorine Levels in Wood Bison (Bison bison athabascae) from the Mackenzie Bison Sanctuary

Abstract

Tissue samples were collected from ten healthy mature female wood bison (B. bison athabascae) for examination. Livers and kidneys were tested for toxic heavy metals and trace metals considered as essential nutrients for successful reproduction, while fat samples were analyzed for persistent chlorinated hydrocarbons. No elevated levels of toxic heavy metals (arsenic, cadmium, lead, mercury) were found and essential trace elements (copper, manganese, selenium, zinc) were within the acceptable ranges established for healthy cattle. All fat samples tested contained trace levels of α-BHC (mean value, 23 ppb) and lindane (mean value, 3 ppb).     

Radiochemical determination of mercury,arsenic, cadmium,zinc and copper in biological materials

Extraction procedure for mercury, arsenic, cadmium, copper and zinc in biological materials is proposed. Mercury and copper are extracted with dithizone followed by the separation of mercury with tri-octyl-amine (TOA). Arsenic, cadmium and zinc are extracted as diethyldithiocarbamates. The procedure is applied for the analysis of some reference materials and autopsy human samples of kidneys, liver, heart, spleen and hair.     

微波消解样品-石墨炉原子吸收光谱法测定双黄连口服液及其药材中重金属元素

双黄连口服液及其中药材金银花、连翘和黄芩苷样品用硝酸-过氧化氢(3+1)混合溶液浸泡过夜,微波消解。并用石墨炉原子吸收光谱法(GF-AAS)测定了铅、镉、铬、铜、铁和锌的含量。磷酸二氢铵、8-羟基喹啉和硒(Ⅱ)分别被用作测定铅,镉,铜和铁、铬以及锌的基体改进剂。在优化的试验条件下,方法的回收率在90.4%～106.0%之间,相对标准偏差(n=5)在1.8%～4.6%之间。试验结果表明,双黄连口服液及其中药材中铁、锌、铜的含量较为丰富,铅和镉含量低于"药用植物及制剂外经贸绿色行业标准"。