Positive microcontact printing with mercaptoalkyloligo(ethylene glycol)s

The soft lithographic replication of patterns with a low filling ratio by microcontact printing (microCP) is problematic due to the poor mechanical stability of common elastomeric stamps. A recently described strategy to avoid this problem employs a modified patterning method, positive microcontact printing ((+)microCP), in which a stamp with a mechanically more stable inverted relief pattern is used. In contrast to conventional negative microCP ((-)microCP), in the contact areas a self-assembled monolayer (SAM) is printed of a "positive ink", which provides only minor etch protection, whereas the noncontacted areas are subsequently covered with a different, etch-resistant SAM, prior to development by chemical etching. With the aim to identify novel, highly versatile positive inks, the patterning of gold by (+)microCP with mercaptoalkyloligo(ethylene glycol)s (MAOEGs), the subsequent adsorption of octadecanethiol (ODT), and the final development by wet chemical etching have now been studied. A polydisperse mixture of mercaptoundecylocta(ethylene glycol) derivatives was found to provide the best patterning results. The surface spreading of the positive ink during stamping, the exchange of printed MAOEGs with ODT, and the choice of the right etching bath were identified as key parameters that influence the achievable pattern resolution and contrast. Due to the modular composition of functionalized alkyloligo(ethylene glycol) derivatives, (+)microCP with these positive inks has the potential for easy adaptation to a variety of materials and development conditions.     

"Lens" effect in directed assembly of nanowires on gradient molecular patterns

We report a new phenomenon, named here as the "lens" effect, in the directed-assembly process of nanowires (NWs) on self-assembled monolayer (SAM) patterns. In this process, the adsorption of NWs is focused in the nanoscale regions at the center of microscale SAM patterns with gradient surface molecular density just like an optical lens focuses light. As a proof of concepts, we successfully demonstrated the massive assembly of V2O5 NWs and single-walled carbon nanotubes (swCNTs) with a nanoscale resolution using only microscale molecular patterning methods. This work provides us with important insights about the directed-assembly process, and from a practical point of view, it allows us to generate nanoscale patterns of NWs over a large area for mass fabrication of NW-based devices.     

In situ real time monitoring of kinetics of thiol adsorption on gold based on electrochemical steady-state current

The growth kinetics of a self-assembled monolayer (SAM) was measured by decrease in steady-state faradic current related to the formation of an insulating SAM. The steady-state current produced by the oxidation of ferrocene in the presence of a rotating disk electrode decreased by introduction of 11-mercaptoundecanoic acid (MUA) related to formation of an insulating MUA SAM. The time constants derived from fitting the measured current to the rearrange-limited Langmuir model agreed well with previously reported results determined using other techniques, demonstrating that our simple method can reliably characterize SAM adsorption kinetics in situ and real timely.     

Selective deposition in multilayer assembly: SAMs as molecular templates

Self-assembled monolayers (SAMs) on surfaces may be used as molecular templates for the selective deposition of polymer multilayer films. SAMs of ω-functionalized alkane thiolates are patterned onto gold surfaces with micron scale features using the microcontact printing method; glass substrates can also be patterned with trichloroalkylsilane SAMs. Patterned polymeric monolayer and multilayer films are adsorbed atop the SAM from dilute polymer solutions using ionic macromolecular self-assembly techniques which have been developed recently. The effects of polymer molecular weight and ionic content, as well as the use of a second SAM in the unpatterned regions to promote selectivity are discussed. Surface roughness, selectivity and other film properties are presented. It is demonstrated that this technique can be used successfully in the patterning of micron scale features with multilayers of low molecular weight upon adsorption from dilute solution.     

Patterning functional materials using channel diffused plasma-etched self-assembled monolayer templates

A simple and cost-effective methodology for large-area micrometer-scale patterning of a wide range of metallic and oxidic functional materials is presented. Self-assembled monolayers (SAM) of alkyl thiols on Au were micropatterned by channel-diffused oxygen plasma etching, a method in which selected areas of SAM were protected from plasma oxidation via a soft lithographic stamp. The patterned SAMs were used as templates for site-selective electrodeposition, electroless deposition and solution-phase deposition of functional materials such as ZnO, Ni, Ag thin films, and ZnO nanowires. The patterned SAMs and functional materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), atomic force microscopy (AFM), and tunneling AFM (TUNA).     

"Sliding kinetics" of single-walled carbon nanotubes on self-assembled monolayer patterns: beyond random adsorption

We present the experimental results and theoretical model describing new adsorption kinetics of single-walled carbon nanotubes (swCNTs) onto self-assembled monolayer (SAM) including their sliding motion. The adsorption behavior of swCNTs on large-size SAM patterns is similar to the Langmuir isotherm, while that on nanoscale patterns shows a significant deviation which can be explained by the sliding motion of adsorbed nanotubes. The "sliding chamber" experiment confirms that swCNTs can align along the SAM patterns by sliding motion right above the SAM surfaces. This result provides new scientific insights regarding the adsorption kinetics of one-dimensional nanostructures, and, from a practical point of view, it can be an important guideline to design SAM patterns to assemble carbon nanotubes and nanowires into desired device structures.     

Substrate effects in poly(ethylene glycol) self-assembled monolayers on granular and flame-annealed gold

Poly(ethylene glycol) (PEG) self-assembled monolayers (SAMs) are surface coatings that efficiently prevent nonspecific adhesion of biomolecules to surfaces. Here, we report on SAM formation of the PEG thiol CH3O(CH2CH2O)17NHCO(CH2)2SH (PEG(17)) on three types of Au films: thermally evaporated granular Au and two types of Au films from hydrogen flame annealing of granular Au, Au(111), and Au silicide. The different Au surfaces clearly affects the morphology and mechanical properties of the PEG(17) SAM, which is shown by AFM topographs and force distance curves. The two types of SAMs found on flame-annealed Au were denoted "soft" and "hard" due to their difference in stiffness and resistance to scratching by the AFM probe. With the aim of nanometer scale patterning of the PEG(17), the SAMs were exposed by low energy (1 kV) electron beam lithography (EBL). Two distinctly different types of behaviour were observed on the different types of SAM; the soft PEG(17) SAM was destroyed in a self-developing process while material deposition was dominant for the hard PEG(17) SAM.     

Directed immobilization of protein-coated nanospheres to nanometer-scale patterns fabricated by electron beam lithography of poly(ethylene glycol) self-assembled monolayers

Controlling the spatial organization of biomolecules on solid supports with high resolution is important for a wide range of scientific and technological problems. Here we report a study of electron beam lithography (EBL) patterning of a self-assembled monolayer (SAM) of the amide-containing poly(ethylene glycol) (PEG) thiol CH(3)O(CH(2)CH(2)O)(17)NHCO(CH(2))(2)SH on Au and demonstrate the patterning of biomolecular features with dimensions approaching 40 nm. The electron dose dependence of feature size and pattern resolution is studied in detail by atomic force microscopy (AFM), which reveals two distinct patterning mechanisms. At low doses, the pattern formation occurs by SAM ablation in a self-developing process where the feature size is directly dose-dependent. At higher doses, electron beam-induced deposition of material, so-called contamination writing, is seen in the ablated areas of the SAM. The balance between these two mechanisms is shown to depend on the geometry of the pattern. The patterned SAMs were backfilled with fluorescent 40-nm spheres coated with NeutrAvidin. These protein-coated spheres adhered to exposed areas in the SAM with high selectivity. This direct writing approach for patterning bioactive surfaces is a fast and efficient way to produce patterns with a resolution approaching that of single proteins.     

Patterning multiple aligned self-assembled monolayers using light

This work describes a method for patterning a gold substrate with multiple, aligned self-assembled monolayers (SAMs) using light at different wavelengths. It describes the synthesis and characterization of an alkanethiolate SAM that is photosensitive to light at both 220 and 365 nm. A photomask acts as an area-selective filter for light at 220 and 365 nm, and a single set of exposures at these two wavelengths through one photomask, without steps of alignment between the exposures, can produce three aligned SAMs on one gold substrate. We demonstrate the versatility of this method of photopatterning by modifying individual aligned SAMs chemically to produce surfaces having different properties. We characterize the modified SAMs using immunolabeling, matrix-assisted laser desorption/ionization time-of-flight mass spectroscopy, and surface plasmon resonance spectroscopy. We also describe the patterning of two aligned SAMs that resist the adsorption of proteins and a third region that does not resist the adsorption of proteins. The ability to produce multiple, aligned patterns of SAMs in a single step, without alignment of photomasks in separate steps, increases the versatility of SAMs for studying a range of physical phenomena.     

High‐Resolution Surface Chemical Analysis of a Trifunctional Pattern Made by Sequential Colloidal Shadowing

We present a new method for creating surface chemical patterns where three chemistries can be periodically arranged at alternate positions on a single substrate without the use of top‐down approaches. High‐resolution chemical imaging by time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS), with nanometer spatial resolution, is used to prove the success of the patterning and subsequent chemical modification steps. We use a combination of colloidal self‐assembly, plasma etching, self‐assembled monolayers (SAMs) and physical vapour deposition (PVD). The method utilizes a double colloid assembly process in which a first layer of close‐packed colloids is created, followed by plasma etching, coating with gold and deposition of a first SAM layer. A second particle layer is deposited on top of the first layer masking the interstitial spaces containing the first SAM. A second gold layer is deposited followed by a second SAM. After particle removal the surface consists of the pattern containing two different SAMs and a SiO₂ layer that can be readily functionalized with silanes. The possibility in the replacement of the two different thiols is investigated by X‐ray photoelectron spectroscopy (XPS) and it was found that no replacement is taking place. ToF‐SIMS imaging is used to show the periodicity of the chemical patterns by tracking unique fragment ions from the different surface regions. The patterning method is adaptable to create smaller or larger chemical patterns by appropriate choice of particle sizes. The patterns are useful for immobilizing biomolecules for cell studies or as multiplexed biosensors.     

Highly Sensitive Electrochemical Sensor for Nitric Oxide Using the Self‐Assembled Monolayer of 1,8,15,22‐Tetraaminophthalocyanatocobalt(II) on Glassy Carbon Electrode

Glassy carbon (GC) electrode modified with a self‐assembled monolayer (SAM) of 1,8,15,22‐tetraaminophthalocyanatocobalt(II) (4α‐Co^IITAPc) was used for the selective and highly sensitive determination of nitric oxide (NO). The SAM of 4α‐Co^IITAPc was formed on GC electrode by spontaneous adsorption from DMF containing 1 mM 4α‐Co^IITAPc. The SAM showed two pairs of well‐defined redox peaks corresponding to Co^III/Co^II and Co^IIIPc^?1/Co^IIIPc^?2 in 0.2 M phosphate buffer (PB) solution (pH 2.5). The SAM modified electrode showed excellent electrocatalytic activity towards the oxidation of nitric oxide (NO) by enhancing its oxidation current with 310 mV less positive potential shift when compared to bare GC electrode. In amperometric measurements, the current response for NO oxidation was linearly increased in the concentration range of 3×10^?9 to 30×10^?9 M with a detection limit of 1.4×10^?10 M (S/N=3). The proposed method showed a better recovery for NO in human blood serum samples.     

Nanoscale patterning of alkyl monolayers on silicon using the atomic force microscope

Self-assembled monolayers (SAMs) of 1-alkenes on hydrogen-passivated silicon substrates were successfully patterned on the nanometer scale using an atomic force microscope (AFM) probe tip. Nanoshaving experiments on alkyl monolayers formed on H-Si(111) not only demonstrate the flexibility of this technique but also show that patterning with an AFM probe is a viable method for creating well-defined, nanoscale features in a monolayer matrix in a reproducible and controlled manner. Features of varying depths (2-15 nm) were created in the alkyl monolayers by controlling the applied load and the number of etching scans made at high applied loads. The patterning on these SAM films is compared with the patterning of alkyl siloxane monolayers on silicon and mica.     

光学活性偶氮苯自组装膜的制备及其蛋白吸附行为

研究了在紫外光作用下, 牛血清白蛋白(BSA)在偶氮苯自组装膜上光控可逆的吸附行为. 首先合成羧基偶氮苯衍生物, 并在金膜表面制备偶氮苯自组装膜, 采用紫外吸收光谱(UV)、原子力显微镜(AFM)观察偶氮苯衍生物的光学顺反异构现象以及偶氮苯自组装膜表面形貌的变化. 同时利用等离子体表面谐振仪(SPR)考察偶氮苯光学异构对牛血清白蛋白(BSA)在自组装膜表面上的吸附行为的影响. 结果表明, BSA在偶氮苯自组装膜表面的吸附作用主要来自于BSA分子与自组装膜之间的静电作用及亲疏水作用. 在紫外光作用下, 偶氮苯自组装膜可以实现光控可逆的牛血清白蛋白分子吸附行为.     

The influence of a self-assembled monolayer on the activity of rough gold for glucose oxidation

Gold surface has been roughened by amalgamation and tested for self-assembled monolayer (SAM) formation and glucose oxidation. The rough gold undergoes structural changes at elevated temperatures, which lead to loss of activity for glucose oxidation and lower affinity for the self-assembly. The transformation of “active” into “inactive” surface can be prevented by SAM formation. The SAM modified gold exhibits high activity for glucose oxidation. These results are important especially for those studies, which use rough gold modified by SAM for enzyme immobilisation and further glucose oxidation, since the gold activity itself was so far neglected.     

Photochemical patterning of a self-assembled monolayer of 7-diazomethylcarbonyl-2,4,9-trithiaadmantane on gold films via Wolff rearrangement

Photolithographic attachment of functional organic molecules via ester or amide linkages to self-assembled monolayers (SAMs) on gold thin films was achieved by employing a novel photoreactive surface anchor, 7-diazomethylcarbonyl-2,4,9-trithiaadmantane. The photoreactive SAM was prepared by the spontaneous physical adsorption of the photoreactive surface anchor onto gold surfaces. The alpha-diazo ketone moiety of the SAM was found to display the classical Wolff rearrangement reactivity to produce a ketene intermediate on the exposed area. Organic molecules such as alcohols and amines can thus be attached to the gold surfaces selectively by the facile in situ formation of ester or amide linkages. The structure and reactivity of the photoreactive surface anchor were characterized by real-time FT-IR, fluorescence, and polarization modulation infrared reflectance absorption spectroscopy (PM-IRRAS). The Wolff rearrangement reactivity of the SAM suggested that a "surface-isolated" carbonylcarbene may be generated when the SAM was exposed to 255-nm irradiation.     

Direct patterning of self-assembled monolayers on gold using a laser beam

The development of a methodology to manipulate surface properties of a self-assembled monolayer (SAM) of alkanethiol on a gold film using direct laser patterning is the objective of this paper. The present study demonstrates proof of the concept for the feasibility of laser patterning monolayers and outlines theoretical modeling of the process to predict the resulting feature size. This approach is unique in that it eliminates the need for photolithography, is noncontact, and can be extended to other systems such as SAMs on silicon wafers or potentially polymeric substrates. A homogeneous SAM made of 1-hexadecanethiol is formed on a 300-A sputtered film of gold (supported by a soda lime glass substrate). Localized regions are then desorbed by scanning the focal spot of a 488-nm continuous-wave argon ion laser beam under a nitrogen atmosphere. The desorption occurs as a result of a high substrate temperature produced by the moving laser beam with a Gaussian spatial profile at a constant speed of 200 microm/s. After completing the scans, the sample is dipped into a dilute solution of 16-mercaptohexadecanoic acid and a hydrophilic monolayer self-assembles along the previously irradiated regions. The resultant lines are viewed, and line widths are measured using both wetting with tridecane under a light microscope and scanning electron microscopy. Using the direct laser patterning method, we have produced straight line patterns with widths of 28-170 microm. A thermal model was constructed to predict the line width of the desorbed monolayer. The effect of the laser power, beam waist, and temperature dependence of the substrate conductivity on the theoretical predictions is considered. It is shown that the theoretical predictions are in good agreement with the experimental results, and, thus, the model can effectively be used to predict experimental results.     

Prediction of the orientations of adsorbed protein using an empirical energy function with implicit solvation

When simulating protein adsorption behavior, decisions must first be made regarding how the protein should be oriented on the surface. To address this problem, we have developed a molecular simulation program that combines an empirical adsorption free energy function with an efficient configurational search method to calculate orientation-dependent adsorption free energies between proteins and functionalized surfaces. The configuration space is searched systematically using a quaternion rotation technique, and the adsorption free energy is evaluated using an empirical energy function with an efficient grid-based calculational method. In this paper, the developed method is applied to analyze the preferred orientations of a model protein, lysozyme, on various functionalized alkanethiol self-assembled monolayer (SAM) surfaces by the generation of contour graphs that relate adsorption free energy to adsorbed orientation, and the results are compared with experimental observations. As anticipated, the adsorbed orientation of lysozyme is predicted to be dependent on the discrete organization of the functional groups presented by the surface. Lysozyme, which is a positively charged protein, is predicted to adsorb on its 'side' on both hydrophobic and negatively charged surfaces. On surfaces with discrete positively charged sites, attractive interaction energies can also be obtained due to the presence of discrete local negative charges present on the lysozyme surface. In this case, 'end-on' orientations are preferred. Additionally, SAM surface models with mixed functionality suggest that the interactions between lysozyme and surfaces could be greatly enhanced if individual surface functional groups are able to access the catalytic cleft region of lysozyme, similar to ligand-receptor interactions. The contour graphs generated by this method can be used to identify low-energy orientations that can then be used as starting points for further simulations to investigate conformational changes induced in protein structure following initial adsorption.     

Oxidation states and CO ligand exchange kinetics in a self-assembled monolayer of a triruthenium cluster studied by in situ infrared spectroscopy

Oxidation states and CO ligand exchange kinetics in a self-assembled monolayer (SAM) of an oxo-centered triruthenium cluster [Ru(3)(mu3-O)(mu-CH3COO)6(CO)(L1)(L2)] (L1 = [(NC5H4)CH2NHC(O)(CH2)10S-]2, L2 = 4-methylpyridine) have been extensively investigated on the surface of a gold electrode in aqueous and nonaqueous solutions. The SAM exhibits three consecutive one-electron transfers and four oxidation states, which have been characterized by electrochemistry, in situ infrared spectroscopy, and in situ sum frequency generation (SFG) vibrational spectroscopy measurements. The original electron-localized state of the Ru cluster center was changed to electron delocalization states by oxidation or reduction of the central Ru ions. These changes are revealed by the IR absorptions of the CO ligand and the bridging acetate ligands of the triruthenium cluster in the SAM. The IR absorptions of the two kinds of ligands are strongly dependent on the oxidation state of the Ru cluster center. One-electron oxidation of the central Ru ion in the SAM triggers a CO ligand liberation process. Solvent molecules may then occupy the CO site to result in a CO-free SAM. One-electron reduction of this CO-free SAM in a CO-saturated solution leads to re-coordination of the CO ligand into the SAM. Both processes can be precisely controlled by tuning the electrode potential. The kinetics of the CO exchange cycle in the SAM, including liberation and coordination, has been investigated by in situ IR and SFG measurements for the first time. The CO exchange cycle is significantly dependent on the temperature. The reaction rate greatly decreases with decreasing solution temperature, which is an important factor in the CO ligand exchange process. The activation energies of both CO liberation and coordination have been evaluated from the reaction rate constants obtained at various temperatures.     

Adsorption behaviors of poly(amido amine) dendrimers with an azacrown core and long alkyl chain spacers on solid substrates

Adsorption behaviors of functional poly(amido amine) dendrimers with an azacrown core and long alkyl chain spacers were investigated on gold and self-assembled monolayer (SAM) by means of time course attenuated total reflection-surface enhanced infrared absorption and surface plasmon resonance spectroscopies. While 1.5th and 2.5th generation (G1.5 and G2.5) ester-terminated dendrimers were slightly adsorbed on all substrates examined, the adsorption of G2 amine-terminated dendrimer increased in the order dodecanethiol SAM相似文献   

Local control of protein binding and cell adhesion by patterned organic thin films

Control of the cell adhesion and growth on chemically patterned surfaces is important in an increasing number of applications in biotechnology and medicine, for example implants, in-vitro cellular assays, and biochips. This review covers patterning techniques for organic thin films suitable for site-directed guidance of cell adhesion to surfaces. Available surface patterning techniques are critically evaluated, with special emphasis on surface chemistry that can be switched in time and space during cultivation of cells. Examples from the authors’ laboratory include the use of cell-repellent self-assembled monolayers (SAM) terminated by oligoethylene glycol (OEG) units and the lifting of the cell repellent properties by use of electrogenerated Br₂/HOBr which can be performed with positionable microelectrodes. Structural changes of the SAM were analyzed by polarization-modulated infrared reflection absorption spectroscopy (PM IRRAS). Use of a soft array system of individually addressable microelectrodes enables formation of flexible and complex patterns in a short time and has the potential for further acceleration of probe-induced local manipulation of cell adhesion.