Ce改性的Pt/γ-Al2O3催化剂用于富氢气氛下CO选择氧化

研究了Ce改性的Pt/γ-Al2O3对于富氢气氛下CO选择氧化反应的催化行为.考察了制备条件(共沉积沉淀法、分步沉积沉淀法以及沉积沉淀温度)对催化活性的影响.结果表明,在80℃时用共沉积沉淀方法制备的催化剂Pt-Ce/γ-Al2O3-CP-80对CO氧化反应表现出良好的活性和选择性,CO转化率在120℃时可以达到85%.利用氢气程序升温还原和原位漫反射红外光谱对不同条件下制备的催化剂进行了表征,分析了Ce的促进作用.     

制备条件对Au/TiO2催化CO氧化性能的影响

采用沉积沉淀法和化学沉积法，分别制备了Au/TiO2催化剂，比较详尽地探讨了制备方法及制备条件对其催化CO氧化性能的影响，并对催化剂进行XRD表征，优化了制备条件，结果显示，控制沉积－沉淀反应液的pH值范围为6．5－7．0，浓度为40mL水／g载体，温度70℃，还原温度85℃,时间60min，以沉积－沉淀法制备的3％Au/TiO2催化剂可于－35℃将CO完全转化，经还原预处理比经焙烧得到的催化剂的活性更高，用光化学沉积法制备的Au/TiO2催化剂的活性欠佳。     

Co/γ-Al2O3催化剂上CO氧化反应的研究

以浸渍法与沉积沉淀法制备了不同Co负载量的Co／γ-Al2O3催化剂，研究了对CO的催化氧化行为,考察了Co含量，焙烧温度，反应温度等对催化剂氧化性能的影响，结果表明，沉积沉淀法制备400℃焙烧的负载量为10％的Co／γ-Al2O3在90℃就能够实现CO完全氧化，且热稳定性比浸渍法制得催化剂好．本文还采用XRD、TPR、XPS等技术，分别研究了Co／γ-Al2O3样品的晶相结构，还原性能及表面化学状态.XRD结果表明，以硝酸盐为前驱物的Co负载于γ-Al2O3后，Co主要以Co3O4结构存在，反应的活性相Co3O4的生成有利于CO催化氧化，且以不同制备方法得到的样品中Co3O4晶粒大小不同，催化活性也不同．TPR结果表明，以沉积沉淀法制备催化剂的还原峰向低温移动，CoOx的还原更加容易．XPS表面分析表明沉淀法制备的Co／γ-Al2O3样品中，Co3O4在载体表面富集．     

Au/Al2O3催化剂的制备及其在CH4/CO2重整反应中的催化活性

采用浸渍法和沉积－沉淀法制备了四种不同的Au/Al2O3催化剂，测定了它们在氢气还原前后及催化反应后的金含量及比表面积，结果表明，制备方法明显影响催化剂的金含量，应用X－光粉末衍射技术研究了这些催化剂经还原处理及反应后的物相变化，金以Au^0物相存在，没有发现氧化态的金物相，考察了该催化剂在CH4／CO2重整反应中的催化活性，发现金催化剂的活性取决于金粒子的大小，浸渍法制备的金催化剂具有较大的金晶粒尺寸，催化活性低，沉积－沉淀法制备的金催化剂金晶粒尺寸较小，催化活性较高，以尿素为沉淀剂制备的催化剂给出1073K时的CH4和CO2转化率分别为8．1％和17．6％，高温反应不仅导致金晶粒的聚集，而且存在明显的金流失现象。     

钴和钾对Pt/γ-Al2O3上CO选择性氧化的助催化作用

 添加Co或/和K助催化剂可在不同程度上改善Pt/γ-Al2O3催化剂对富氢气氛下CO选择性氧化的性能. 利用H2-TPR,CO-TPD和FT-IR等表征手段,探讨了不同助催化剂的作用机理. 结果表明,Co/Pt/γ-Al2O3能显著降低富氢气氛下CO选择性氧化的温度,主要原因是Co与Pt的相互作用使Pt的电子性能发生了改变,从而削弱了Pt对CO的吸附,使催化剂表面CO的线式吸附消失; Co的添加还促进了易分解的碳酸氢盐物种的生成,同时未完全还原的CoOx物种可提供活性氧促进CO的转化. 助催化剂K一方面促进了Pt向CO反馈电子,从而活化吸附的CO,提高了催化剂的低温活性;另一方面促进了难分解的甲酸盐物种的生成,从而抑制了部分活性位,需要更高的反应温度,而较高温度下会发生氢气氧化反应的竞争,使CO选择性氧化反应的活性和选择性受到影响. 同时添加K和Co的催化剂中,K可促进CoOx的还原,使Co与Pt的相互作用变弱,即减弱了Co对Pt的助催化作用, 因此虽然其选择性有所改善,但活性介于单独添加Co或K的催化剂之间.     

Pt-CeO_2/SiO_2催化剂用于室温湿空气中CO氧化反应（英文）

开发室温CO氧化催化剂的主要挑战是CO自中毒和慢的表面动力学,同时湿气的存在也可导致催化剂失活.本文开发了高活性CeO_2促进的Pt基催化剂4%Pt-12%CeO_2/Si O_2,用于室温湿气(湿度10%–90%,25°C)中CO氧化反应,在低CO浓度(500 ppm)和高CO浓度(2500 ppm)时,CO转化率高于99%.优化了催化剂制备变量,如Pt和CeO_2负载量、CeO_2沉积方法、CeO_2和Pt前驱体的干燥和焙烧条件.采用CO/H_2化学吸附、O_2-H_2滴定、X射线衍射和BET比表面积测定表征了催化剂的表面特性,并将其与催化剂活性相关联.结果表明,CeO_2沉积方法对催化剂活性影响显著,当用浸渍法沉积CeO_2时,所得催化剂的反应速率(5.77μmol/g/s)比用沉积沉淀法(1.96μmol g~(-1)s~(-1))或CeO_2嫁接法(1.31μmol g~(-1)s~(-1))制得催化剂的高3倍.O_2-H_2滴定结果表明,当用浸渍法沉积CeO_2时,CeO_2和Pt的紧密结合导致了催化剂的高活性.催化剂载体的选择也非常重要,硅胶负载的催化剂活性(5.77μmol g~(-1)s~(-1))是氧化铝负载的(1.05μmol g~(-1)s~(-1))5倍.当反应受内扩散控制时,催化剂载体的粒径和孔结构影响非常大.另外,CeO_2和Pt前驱体的干燥和焙烧条件对催化剂活性的影响至关重要.当Pt和CeO_2含量分别大于2.5和15 wt%时,所得催化剂在室温条件下活性高(TOF0.02 s~(-1)),稳定性好(反应15 h,CO转化率≥99%).     

丙烯气相直接环氧化Au/TiO2催化剂的研究

在H2和O2共存条件下，金催化剂催化丙烯气相直接环氧化反应是近年来发展起来的一种新型环氧丙烷(PO)合成技术．本文采用沉积沉淀法制备了一系列Au／TiO2催化剂，考察了反应溶液的pH值、Au负载量、沉淀剂以及焙烧温度等因素对催化剂丙烯环氧化催化性能的影响．结果表明制备条件对催化性能有明显影响：反应溶液的pH值为7．5及Au负载量为2．4％时所得催化剂活性最好；当以Na2CO3、NaOH等含Na^ 物质作为沉淀剂时，催化性能明显优于Li^ 、K^ 等其它碱金属离子；400℃焙烧制得的催化剂活性较好，在50℃低温反应条件下，环氧丙烷得率可达1．3％．HRTEM结果表明，催化剂中Au组分高度分散于载体表面，且随着焙烧温度的增加Au粒因发生聚集而变大，从而影响了催化剂的活性．表面XPS分析证实，活性较好的Au／TiO2催化剂中活性组分Au除部分呈氧化态外，主要是以金属态的形式存在．     

Pt-CeO2/SiO2催化剂用于室温湿空气中CO氧化反应

开发室温CO氧化催化剂的主要挑战是CO自中毒和慢的表面动力学,同时湿气的存在也可导致催化剂失活.本文开发了高活性CeO2促进的Pt基催化剂4%Pt-12%CeO2/SiO2,用于室温湿气(湿度10%?90%,25°C)中CO氧化反应,在低CO浓度(<500 ppm)和高CO浓度(>2500 ppm)时,CO转化率高于99%.优化了催化剂制备变量,如Pt和CeO2负载量、CeO2沉积方法、CeO2和Pt前驱体的干燥和焙烧条件.采用CO/H2化学吸附、O2-H2滴定、X射线衍射和BET比表面积测定表征了催化剂的表面特性,并将其与催化剂活性相关联.结果表明,CeO2沉积方法对催化剂活性影响显著,当用浸渍法沉积CeO2时,所得催化剂的反应速率(5.77μmol/g/s)比用沉积沉淀法(1.96μmol g?1 s?1)或CeO2嫁接法(1.31μmol g?1 s?1)制得催化剂的高3倍.O2-H2滴定结果表明,当用浸渍法沉积CeO2时,CeO2和Pt的紧密结合导致了催化剂的高活性.催化剂载体的选择也非常重要,硅胶负载的催化剂活性(5.77μmol g?1 s?1)是氧化铝负载的(1.05μmol g?1 s?1)5倍.当反应受内扩散控制时,催化剂载体的粒径和孔结构影响非常大.另外,CeO2和Pt前驱体的干燥和焙烧条件对催化剂活性的影响至关重要.当Pt和CeO2含量分别大于2.5和15 wt%时,所得催化剂在室温条件下活性高(TOF>0.02 s?1),稳定性好(反应15 h,CO转化率≥99%).     

Pb-Pt/AC催化甘油一步法制备丙酮酸（英文）

生物质能具有绿色环保、可再生、来源广泛和安全性高等优点,成为当前的研究热点.作为生物柴油的主要副产物甘油是一种重要的生物质平台化合物.甘油的高效利用,不仅能够获得重要的精细化学品及聚合物,也可以延长生物柴油的产业链,降低其生产成本,增加其市场竞争力.丙酮酸是一种弱有机酸,为生物体内葡萄糖分解代谢的中间产物,在生物能量代谢和物质代谢过程中起着重要的枢纽作用.同时,由于它同时含有羧基和酮羰基,具有很强的反应性,可参与多种化学反应,在化学工业中有广泛应用.目前,工业上主要采用酒石酸脱水脱羧法生产丙酮酸,丙酮酸收率可达50.55%,但生产过程需要消耗大量的KHSO4粉末,生产成本高,且高耗能高污染,不符合可持续发展的要求.因此,利用可再生资源甘油在温和条件下生产丙酮酸显现出良好的应用前景.目前,由甘油一步法获得丙酮酸仅可通过发酵法实现,但是其规模化生产存在效率低、废弃物污染等问题.因此,研究化学方法由甘油一步制备丙酮酸可行也十分必要.本课题组以Pt/AC或Cu-Pt/AC为催化剂进行甘油氧化制备乳酸的研究,所得产物中几乎未检出丙酮酸;当以Pb-Pt/C为催化剂进行乳酸脱氢氧化制备丙酮酸,可获得较高选择性的丙酮酸.因此,本文通过向Pt/AC催化剂中引入Pb助剂,以期调变甘油氧化的产物分布,从而获得相对高的丙酮酸选择性.通过浸渍-沉积沉淀法(Im-DP)制备了一系列不同Pb载量(1.7.0 wt%)的xPb-5Pt/AC-Im-DP催化剂,并采用不同方法制备了一系列5Pb-5Pt/AC催化剂,用于在温和条件下甘油选择性氧化制备丙酮酸反应中.结果表明,Pb载量和催化剂制备方法都对其催化活性有显著影响.当xPb-5Pt/AC-Im-DP催化剂中Pb载量为1%时,甘油转化率和丙酮酸选择性均较单金属5Pt/AC催化剂高,但当Pb载量继续升高至3%及以上时,甘油转化率明显下降.我们推测这与Pb3(CO3)2(OH)2物种的形成有关.采用该方法制备催化剂时,Pb载量宜为5.0 wt%.保持Pt和Pb载量均为5.0 wt%,采用共沉积沉淀(Co-DP)、共浸渍(Co-Im)、以及对催化剂进行500 oC氩气焙烧等,制备了具有Pb3(CO3)2(OH)2物种、铂铅合金物种(PtPb和PtxPb)和两物种均没有的5Pb-5Pt/AC催化剂.通过评价它们的催化性能,进一步探究了Pb3(CO3)2(OH)2物种、铂铅合金物种、表面金属价态与催化剂活性的关系.实验表明,Pb3(CO3)2(OH)2和表面Pb0物种不利于甘油的转化,铂铅合金对甘油转化有一定的促进作用,对丙酮酸生成显现出明显促进作用.通过对Co-DP、Im-DP催化剂进行500 oC氩气焙烧,能够除去Pb3(CO3)2(OH)2物种,同时形成铂铅合金.综上,本文在温和条件下,采用Pb-Pt/AC催化剂进行甘油选择性氧化制备丙酮酸反应.采用优化的方法制备的5Pb-5Pt/AC催化剂在90 oC条件下反应10 h,丙酮酸收率可达18.4%,这是目前甘油一步法氧化制备丙酮酸的最高值.进一步优化反应条件、催化剂组成与结构,探索反应机理仍十分必要     

Pb-Pt/AC催化甘油一步法制备丙酮酸

生物质能具有绿色环保、可再生、来源广泛和安全性高等优点,成为当前的研究热点.作为生物柴油的主要副产物,甘油是一种重要的生物质平台化合物.甘油的高效利用,不仅能够获得重要的精细化学品及聚合物,也可以延长生物柴油的产业链,降低其生产成本,增加其市场竞争力.丙酮酸是一种弱有机酸,为生物体内葡萄糖分解代谢的中间产物,在生物能量代谢和物质代谢过程中起着重要的枢纽作用.同时,由于它同时含有羧基和酮羰基,具有很强的反应性,可参与多种化学反应,在化学工业中有广泛应用.目前,工业上主要采用酒石酸脱水脱羧法生产丙酮酸,丙酮酸收率可达50–55%,但生产过程需要消耗大量的KHSO4粉末,生产成本高,且高耗能高污染,不符合可持续发展的要求.因此,利用可再生资源甘油在温和条件下生产丙酮酸显现出良好的应用前景.目前,由甘油一步法获得丙酮酸仅可通过发酵法实现,但是其规模化生产存在效率低、废弃物污染等问题.因此,研究化学方法由甘油一步制备丙酮酸可行也十分必要.本课题组以Pt/AC或Cu-Pt/AC为催化剂进行甘油氧化制备乳酸的研究,所得产物中几乎未检出丙酮酸;当以Pb-Pt/C为催化剂进行乳酸脱氢氧化制备丙酮酸,可获得较高选择性的丙酮酸.因此,本文通过向Pt/AC催化剂中引入Pb助剂,以期调变甘油氧化的产物分布,从而获得相对高的丙酮酸选择性.通过浸渍-沉积沉淀法(Im-DP)制备了一系列不同Pb载量(1–7.0 wt%)的xPb-5Pt/AC-Im-DP催化剂,并采用不同方法制备了一系列5Pb-5Pt/AC催化剂,用于在温和条件下甘油选择性氧化制备丙酮酸反应中.结果表明,Pb载量和催化剂制备方法都对其催化活性有显著影响.当xPb-5Pt/AC-Im-DP催化剂中Pb载量为1%时,甘油转化率和丙酮酸选择性均较单金属5Pt/AC催化剂高,但当Pb载量继续升高至3%及以上时,甘油转化率明显下降.我们推测这与Pb3(CO3)2(OH)2物种的形成有关.采用该方法制备催化剂时,Pb载量宜为5.0 wt%.保持Pt和Pb载量均为5.0 wt%,采用共沉积沉淀(Co-DP)、共浸渍(Co-Im)、以及对催化剂进行500oC氩气焙烧等,制备了具有Pb3(CO3)2(OH)2物种、铂铅合金物种(PtPb和PtxPb)和两物种均没有的5Pb-5Pt/AC催化剂.通过评价它们的催化性能,进一步探究了Pb3(CO3)2(OH)2物种、铂铅合金物种、表面金属价态与催化剂活性的关系.实验表明,Pb3(CO3)2(OH)2和表面Pb0物种不利于甘油的转化,铂铅合金对甘油转化有一定的促进作用,对丙酮酸生成显现出明显促进作用.通过对Co-DP、Im-DP催化剂进行500oC氩气焙烧,能够除去Pb3(CO3)2(OH)2物种,同时形成铂铅合金.综上,本文在温和条件下,采用Pb-Pt/AC催化剂进行甘油选择性氧化制备丙酮酸反应.采用优化的方法制备的5Pb-5Pt/AC催化剂在90oC条件下反应10 h,丙酮酸收率可达18.4%,这是目前甘油一步法氧化制备丙酮酸的最高值.进一步优化反应条件、催化剂组成与结构,探索反应机理仍十分必要.     

Catalytic hydrogenation of 1,3-trans-pentadiene over Rh4(CO)12 supported on γ-Al2O3

Rh₄(CO)₁₂ anchored on γ-Al₂O₃ (Rh₄(CO)₁₂/Al₂O₃) has been studied as a catalyst for the hydrogenation of 1,3-trans-pentadiene. Under mild conditions (1 atm H₂ and temperatures between 60°C and 80°C) hydrogenation occurs at only one of the double bonds of the diene, and analysis of the products shows that the terminal double bond is preferentially hydrogenated. Hydrogenation of the second double bond of the conjugated diene occurring only after all the 1,3-trans-pentadiene has been consumed. In this respect Rh₄(CO)₁₂/Al₂O₃ behaves like toluene solutions of Rh₄(CO)₁₂. Anchoring of Rh₄(CO)₁₂ on the solid support gives a catalyst which is less active but more stable than toluene solutions of Rh₄(CO)₁₂. The effects of CO and of triphenylphosphine on catalytic activity and on specificity of Rh₄(CO)₁₂/Al₂O₃ have also been investigated and both shown to cause a reduction of the rate of hydrogenation of 1,3-trans-pentadiene.     

Hydrocracking of Tar Components from Hot Coke Oven Gas over a Ni/Ce-ZrO2/γ-Al2O3 Catalyst at Atmospheric Pressure

Ni/Ce-ZrO₂/γ-Al₂O₃ catalysts with different Ce-ZrO₂ contents and Ni loadings were prepared by a two step impregnation method and characterized by X-ray diffraction, transmission electron microscopy, N₂ adsorption, and temperature-programmed reduction. The catalysts were used for the hydrocracking of toluene and naphthalene, which were model tar compounds in hot coke oven gas, under atmospheric pressure at 800 °C. They showed excellent catalytic activity, stability, and some sulfur tolerance. Both toluene and naphthalene was converted into light fuel gases even at a low mole ratio of steam to carbon (S/C = 0.44). During the testing period of 7 h, no coke deposition was observed on the surface of the catalysts. The results indicated that the addition of Ce-ZrO₂ limited the sintering of Ni particles and enhanced the catalytic activity. The Ni/Ce-ZrO₂/γ-Al₂O₃ catalyst is promising for the direct removal of tar compounds in hot coke oven gas with low S/C ratios.     

Preparation of Nano-Sized γ-Al2O3 Supported Iron Catalyst for Fischer-Tropsch Synthesis by Solvated Metal Atom Impregnation Methods

Two types of small iron clusters supported onγ-Al2O3-RT(dehydroxylated at room temperature) andγ-Al2O3-800 (dehydroxylated at 800℃) were prepared by solvated metal atom impregnation (SMAI) techniques. The iron atom precursor complex, bis(toluene)iron(0) formed in the metal atom reactor, was impregnated intoγ-Al2O3 having different concentrations of surface hydroxyl groups to study the effect of surface hydroxylation on the crucial stage of iron cluster formation. Catalysts prepared in this way were characterized by TEM, Mossbauer, and chemisorption measurements, and the results show that higher concentration of surface hydroxyl groups ofγ-Al2O3-RT favors the formation of more positively charged supported iron cluster Fen/γ-Al2O3-RT, and the lower concentration of surface hydroxyl groups ofγ-Al2O3-800 favors the formation of basically neutral supported iron cluster Fen/γ-Al2O3-800. The measured results also indicate that the higher concentration of surface hydroxyl groups causes the rapid decomposition of precursor complex, bis(toluene)iron(0), and favors the formation of relatively large iron cluster. Consequently, these two types of catalysts show different catalytic properties in Fischer-Tropsch reaction. The catalytic pattern of Fen/γ-Al2O3-RT in F-T reaction is similar to that of the unreducedα-Fe2O3 and that of Fen/γ-Al2O3-800 is similar to that of the reducedα-Fe2O3.     

La2O3/γ-Al2O3催化剂用于二甲醚二氧化碳重整制氢

采用等体积浸渍法制备了不同负载量的La₂O₃/γ-Al₂O₃催化剂,并考察了负载量和反应温度对催化剂用于二甲醚二氧化碳重整制氢反应的性能影响。结果表明,反应温度为550℃、La₂O₃负载量为15%时,催化剂表现出最好的性能：二甲醚的转化率为100%,二氧化碳的转化率达到85.4%,产物氢气的选择性高达93.3%,一氧化碳的选择性为76.04%,副产物甲烷的选择性仅为6.3%。550 ℃时其平均积炭速率为1.387 5 mg/（g·h）。研究还利用XRD、BET、TEM、TG等方法对催化剂进行了表征。     

Preparation of “pore-fill” type Pd–YSZ–γ-Al2O3 composite membrane supported on α-Al2O3 tube for hydrogen separation

Mesoporous YSZ–γ-Al₂O₃ membranes were coated on α-Al₂O₃ (Ø2 mm) tube by dipping the α-Al₂O₃ support tube into mixed sol consists of nano-size YSZ and bohemite particles followed by drying and calcination at 600 °C. Addition of bohemite in YSZ sol helped a good adhesion and uniform coating of the membrane film onto α-Al₂O₃ support. The quality of the mesoporous YSZ–γ-Al₂O₃ membranes was evaluated by the gas permeability experiments. The number of defects was minimized when the γ-Al₂O₃ content became more than 40%. Addition of γ-Al₂O₃ inhibited the crystal growth of YSZ, sintering shrinkage and distortion stress. Increase of calcination temperature and time results in the increase of pore size and N₂ permeance. A hydrogen perm-selective membrane was prepared by filling palladium into the nano-pores of YSZ–γ-Al₂O₃ layer by vacuum-assisted electroless plating. Crystal growth of palladium was observed by thermal annealing of the membrane at 600 °C for 40 h. The Pd–YSZ–γ-Al₂O₃ composite membrane revealed improved thermal stability allowing long-term operation at elevated temperature (>500 °C). This has been attributed to the improved fracture toughness of YSZ–γ-Al₂O₃ layer and matching of thermal expansion coefficient between palladium and YSZ. Although fracture of the membrane did not occur, decline of H₂ flux was observed when the membrane was exposed in 600 °C. This has been attributed to the agglomeration of palladium particles by crystal growth and dense packing into the pore networks of YSZ–γ-Al₂O₃ by elevation of temperature.     

CeO2-ZrO2-La2O3-Al2O3 composite oxide and its supported palladium catalyst for the treatment of exhaust of natural gas engined vehicles

Composite supports CeO2-ZrO2-Al2O3 (CZA) and CeO2-ZrO2-Al2O3-La2O3 (CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperature-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Catalytic activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. They also have significant potential in industrial application because of their high performance and low cost.     

Effect of LaFeO3 Decoration and Ozone Treatment on Thermal Stability of Au/Al2O3 for CO Oxidation

The 1.1%Au/LaFeO_x/Al₂O₃ catalysts were prepared by the iso-volume impregnation method and activated with H₂ or O₃. The catalytic performance for CO oxidation at room temperature was investigated by accelerated deactivation tests in 1.0% CO reactant stream at 550 °C. The introduction of La and Fe enhanced the thermal stability of Au/Al₂O₃ with a decrease in initial activity, probably due to the formation of LaFeO₃ perovskite on the Al₂O₃ surface. The 1.1%Au/2%LaFeO₃/Al₂O₃ catalyst activated by H₂ can transform 65% CO into CO₂ at room temperature after pretreatment in 1.0% CO reactant stream at 550 °C for 2 h, whereas 1.1%Au/Al₂O₃ activated by H₂ totally loses its activity. O₃ activation can always make 1.1%Au/LaFeO₃/Al₂O₃ more active than that of H₂ activation during the pretreatment process in 1.0% CO. After pretreatment for 10 h, 1.1%Au/2%LaFeO₃/Al₂O₃ activated by O₃ still shows 40% conversion of 1.0% CO at room temperature, whereas those activated by H₂ become inactive completely. The better thermal stability of the catalysts activated by O₃ may be due to that O₃ activation leads to the formation of partially oxidized state of Au in Au/FLA-O₃, which may reinforce the interaction between the metal and support.     

合成方法对Rh/CeO2-ZrO2-La2O3催化剂的结构、表面性能及DeNOx活性的影响

用沉积沉淀法合成两种不同系列的CeO2-ZrO2-La2O3混合氧化物(ZrO2和La2O3沉积CeO2粒子(标记为A-x)以及CeO2和La2O3沉积ZrO2粒子(标记为B-x)),并用作Rh催化剂的载体。XRD、拉曼、TPR、XPS和O2脉冲等表征结果显示出不同的沉积顺序将导致不同的结构和氧化还原性能,且B-x具有更高的氧迁移性、储氧能力和表面Ce浓度。当其负载Rh后,Rh/B-x催化剂具有更高的NO和CO转化率及N2选择性,且Ce的最佳含量为50at%。这可能归因于Rh负载于富铈表面形成更多有利于NO分解的表面Ce3+活性位。     

Racemization of chiral amino alcohols III: Effect of Mg or Ca addition on the activity and stability of the Co/γ-Al2O3 catalyst

The racemization of R-(-)-2-amino-1-butanol in a reaction using Co/γ-Al₂O₃ catalysts and catalysts modified by Mg or Ca was investigated in this paper. Complete racemization was achieved with a yield of over 83% at using the Mg modified Co/γ-Al₂O₃ catalyst under optimized reaction conditions of 170°C and 2.5 MPa of H₂. The catalysts were thoroughly characterized by XRD, XPS, TPR, SEM and TEM. The addition of Mg and Ca may be advantageous for dispersing and stabilizing the active species of the Co/γ-Al₂O₃ catalyst, protecting from sintering, significantly improving its catalytic activity and stability.     

Mo_2C/γ-Al_2O_3催化剂上苯加氢反应的原位红外光谱研究

采用程序升温反应法制备了钝化态、还原钝化态和新鲜态Mo2C/γ-Al2O3催化剂,结合原位红外光谱表征技术和反应性能评价,考察、比较了三种催化剂苯加氢反应活性.原位红外光谱结果表明,新鲜态Mo2C/γ-Al2O3催化剂在室温就显示了较好的苯加氢反应活性,表现了类贵金属的催化活性.CO吸附在反应前后新鲜态Mo2C/γ-Al2O3催化剂上的对比结果表明,低价态的Mo位(Moδ+(0δ2))是苯加氢反应活性中心.三种催化剂的反应活性结果表明,新鲜态Mo2C/γ-Al2O3催化剂反应活性最好,催化剂寿命最长,失活之后在500°C下H2处理即可恢复原有活性.