ZrO2负载碳纳米管吸附去除水中氟的研究

以ZrO2负载多壁碳纳米管(ZrO2-MWCT)为吸附剂,系统研究了其对水中F-的吸附、脱附性能。结果表明,F-在ZrO2-MWCT吸附剂上的吸附等温线可以用Freundlich方程模拟,吸附动力学符合拟二级动力学方程,吸附速率随着F-初始浓度的提高而减低。当pH为4~5时,F-在ZrO2-MWCT吸附剂上的吸附量最大。水中阴离子的存在降低ZrO2-MWCT对F-的吸附量,不同阴离子对F-影响的大小顺序为:CO32->SO42->Cl->NO3-。吸附饱和的ZrO2-MWCT可用0.1mol/L的NaOH脱附再生,经4次再生后,其吸附量仍为14.55mg/g。     

铁锆复合氧化物催化甲醇与CO2直接合成 DMC反应性能

采用溶胶-凝胶法制备的铁锆复合氧化物催化甲醇与CO2直接合成碳酸二甲酯（DMC）反应,其催化活性远高于氧化铁和氧化锆,当铁锆摩尔比为5：1时,其催化活性是氧化锆的2倍。利用XRD、XPS、IR、TPD和N2物理吸附-脱附等技术对催化剂进行了表征。结果表明,氧化铁主要以六方晶相的α-Fe2O3形式存在,氧化锆主要以四方晶相存在,铁锆之间发生了相互作用,使铁锆复合氧化物表面L酸增强和少量B酸产生。L酸的增强和B酸的产生是催化剂催化活性增加的主要原因,并对催化剂的催化作用机理进行了探讨。     

Cu/ZrO2催化剂中的氢和水逆溢流效应及其对甲醇分解反应的影响

应用漫反射红外和质谱在线技术对H₂, H₂O及甲醇在ZrO₂及Cu/ZrO₂上的程序升温脱附(TPD)及程序升温反应(TPSR)行为进行了研究. 结果表明, Cu/ZrO₂催化剂中铜锆组分间表现出显著的氢和水组分“逆溢流”效应. 对Cu/ZrO₂催化体系中ZrO₂表面线式及桥式羟基物种浓度随还原预处理温度变化的进一步分析表明, 由于氢和水“逆溢流效应”的存在, 使得Cu/ZrO₂在较低的还原温度下活化的同时, 在铜锆界面处形成较丰富的氧阴离子和氧空穴活性位, 而后者的形成与存在直接影响并决定了甲醇在Cu/ZrO₂催化剂上的低温催化分解行为.     

ZrO2—SiO2负载Cu—Ni催化剂的CO2加氢反应性能

采用表面反应改性法,制备了ZrO2-SiO2（ZrSiO)表面复合物载体,用等体积浸渍法制备了ZrSiO担载的Cu-Ni双金属催化剂,借助BET、TPR、IR和微反等技术,研究了ZrSiO及其负载的Ni、Cu双金属催化剂的表面构造,化学吸附及催化CO2加氢的反应性能,结果表明,ZrSiO表面主要是价联型结构,ZrO2引入SiO2表面,可以有效地促进CuO和NiO的还原,在ZrSiO负载的Cu-Ni催化剂表面的Cu或Ni位,CO2发生化学 吸附形成线、剪式、卧式吸附态,在该催化剂上CO2的加氢反应产物主要是CH3OH3、CH4、CO和H2O生成CH3OH的选择性与催化剂组成及反应条件密切相关,在适当的条件,CH3OH的选择性大于90％。     

Acidity of mesoporous MoO(x)/ZrO2 and WO(x)/ZrO2 materials: a combined solid-state NMR and theoretical calculation study

The acidity of mesoporous MoO(x)/ZrO2 and WO(x)/ZrO2 materials was studied in detail by multinuclear solid-state NMR techniques as well as DFT quantum chemical calculations. The 1H MAS NMR experiments clearly revealed the presence of two different types of strong Br?nsted acid sites on both MoO(x)/ZrO2 and WO(x)/ZrO2 mesoporous materials, which were able to prontonate adsorbed pyrine-d5 (resulting in 1H NMR signals at chemical shifts in the range 16-19 ppm) as well as adsorbed trimethylphosphine (giving rise to 31P NMR signal at ca. 0 ppm). The 13C NMR of adsorbed 2-(13)C-acetone indicated that the average Br?nsted acid strength of the two mesoporous materials was stronger than that of zeolite HZSM-5 but still weaker than that of 100% H2SO4, which was in good agreement with theoretical predictions. The quantum chemical calculations revealed the detailed structures of the two distinct types of Br?nsted acid sites formed on the mesoporous MoO(x)/ZrO2 and WO(x)/ZrO2. The existence of both monomer and oligomer Mo (or W) species containing a Mo-OH-Zr (or W-OH-Zr) bridging OH group was confirmed with the former having an acid strength close to zeolite HZSM-5, with the latter having an acid strength similar to sulfated zirconia. On the basis of our NMR experimental and theoretical calculation results, a possible mechanism was proposed for the formation of acid sites on these mesoporous materials.     

CrOx在ZrO2上的分散状态及其CO还原NO性能的研究

利用XRD和BET等物理技术研究了CrOx对ZrO2的抗烧结性能及Cr的分散状态.结果表明,CrOx是良好的ZrO2抗烧结剂,会抑制ZrO2晶型从无定形→四方→单斜的相变过程;CrOx与ZrO2之间的强相互作用还有利于Crox在ZrO2表面的分散.NO的TPD-MS实验表明,NO在CrOx/ZrO2表面存在两种与ZrO2作用强弱不同的吸附态,在程序升温脱附过程中发生了NO的离解反应.NO+CO的反应实验表明,反应过程中存在中间产物N2O,低温有利生成N2O,而高温有利于转化成N2.     

单斜及四方晶相ZrO2催化CO加氢反应性能的比较

研究了以纯单斜（ｍ）和四方（ｔ）晶相ＺｒＯ２为催化剂的ＣＯ加氢反应．尽管两种晶相催化剂均有较高的低碳烯烃的选择性,但是也发现了两者催化性能的显著差别．ｍ－ＺｒＯ２催化剂对异丁烯有突出的选择性,而ｔ－ＺｒＯ２催化剂,则只有乙烯和丙烯,几乎没有Ｃ４烯烃的选择性．室温下ＣＯ吸附的原位ＩＲ谱测试可见,只有在ｔ－ＺｒＯ２催化剂上观测到不可逆含氧吸附物种．吡啶吸附的Ｒａｍａｎ谱显示出它们之间表面性质的差别,ｍ－ＺｒＯ２催化剂表面存在等强度的Ｌｅｗｉｓ和Ｂｒｏｎｓｔｅｄ酸中心,而在ｔ－ＺｒＯ２催化剂表面几乎只有Ｂｒｏｎｓｔｅｄ酸中心．催化过程的一些模型分子电子结构计算也表明了ＺｒＯ２催化剂对低碳烯烃选择性内在的电子结构条件．我们推测ＣＯ在ｍ－ＺｒＯ２催化剂表面的孪式吸附物种可能是导致异丁烯产物的根源     

氧化锆负载Pd-Cu双金属催化剂上山梨醇选择性氢解合成乙二醇和丙二醇

山梨醇和木糖醇等多元醇是可再生生物质转化合成液体燃料和化学品的重要平台分子,其中,可通过选择氢解反应一步制备乙二醇和丙二醇等重要化工原料,有望代替从乙烯和丙烯制备二元醇的传统石油化工工艺.目前文献中多元醇氢解反应主要使用Ru基和Ni基催化剂等,但是不可避免地生成C?C键非选择性断裂的副产物甲烷等.与之相比,非贵金属Cu基催化剂往往具有较优异的选择性,但其活性较低和水热稳定性较差.因此,到目前为止研制具有高活性和选择性、以及良好水热稳定性的Cu基催化剂用于生物质基多元醇氢解反应仍然存在挑战.在本文中,我们采用贵金属修饰的方法提高Cu基催化剂在山梨醇选择氢解反应中的活性和水热稳定性.通过分步浸渍法合成了1%Pd-3%Cu/ZrO2、1%Pt-3%Cu/ZrO2和1%Ru-3%Cu/ZrO2双金属催化剂,并比较了它们在山梨醇氢解反应中的催化性能.在相同的反应条件下,上述催化剂中1%Pd-3%Cu/ZrO2(Cu/Pd =5)具有最优的活性及乙二醇、丙二醇和甘油的总选择性.以固体碱La(OH)3为助剂,1%Pd-3%Cu/ZrO2的山梨醇氢解活性高达20.3 h-1,是单金属1%Pd/ZrO2(8.7 h-1)和3%Cu/ZrO2(6.5 h-1)催化剂活性的2-3倍,也高于含有相同Pd、Cu含量的1%Pd/ZrO2和3%Cu/ZrO2机械混合体系的活性(12.2 h-1).而且, Pd-Cu/ZrO2双金属催化剂对C2-C3低碳多元醇的选择性也明显优于Pd/ZrO2和Cu/ZrO2以及二者的机械混合体系.这些结果说明Pd对Cu/ZrO2的促进作用不仅仅需要Pd与Cu两种金属的共同存在,还需要它们两者之间的相互作用.进一步发现, Pd-Cu/ZrO2双金属催化剂在Cu/Pd比为1.5-10.0的较宽范围内都表现出了较高的反应活性(17.8-20.3 h-1)以及乙二醇、丙二醇和甘油的总选择性(57.3%-62.8%),说明较低含量Pd的存在就能够有效地改善Cu催化剂的催化性能.在493 K和5.0 MPa H2的反应条件下,以1%Pd-3%Cu/ZrO2为催化剂,在山梨醇接近完全转化时,获得了61.7%的乙二醇、丙二醇和甘油的总选择性.同时, Pd的加入还能有效地抑制水热反应条件下Cu粒子的团聚,使得Pd-Cu/ZrO2催化剂在山梨醇氢解反应中具有优良的水热稳定性和循环使用性能.在5次循环实验中1%Pd-3%Cu/ZrO2的活性和选择性基本保持不变; X-射线粉末衍射结果表明,反应后的催化剂上未观察到Cu的特征衍射峰, Cu粒子仍然保持良好的分散状态.而对于没有Pd修饰的单金属3%Cu/ZrO2催化剂,经5次循环使用后山梨醇氢解反应的活性则下降了42%;在循环反应中Cu粒子显著地聚集而长大到~30 nm. CO吸附漫反射红外光谱结果揭示了Cu粒子倾向于在Pd粒子表面沉积,随着Cu/Pd原子比的增大, Cu粒子逐渐稀释并覆盖Pd的表面位点,说明Pd与Cu粒子之间存在紧密的接触.氢气程序升温还原结果表明,可能与氢溢流有关, Pd的加入促进了CuO的还原.然而,不同于Pd/ZrO2和Cu/ZrO2机械混合样品的TPR图谱,其显示PdO和CuO各自的还原峰, Pd-Cu双金属催化剂则只存在一个宽化的还原峰,这说明了Pd-Cu之间结构上的紧密接触使得两种金属之间存在强相互作用,其中可能存在从Pd向Cu的电子转移.综合这些结构和电子效应,可以推测Pd的存在促进了Cu粒子对山梨醇的脱氢能力和不饱和中间体的加氢能力,进而提高了Cu基催化剂在山梨醇氢解反应中的活性及目标产物的选择性.同时Pd-Cu之间的强相互作用和氢溢流效应抑制了Cu粒子在水热反应条件下的聚集,提高了催化剂的稳定性.这些结果和认识有助于指导人们为多元醇氢解和其它生物质基化学品的转化反应设计具有更高效率和水热稳定性的新型Cu基催化剂.     

Fourier transform infrared spectroscopic study of surface acidity by pyridine adsorption on Mo/ZrO2-SiO2(Al2O3) catalysts

Acidity of the oxidic molybdenum catalysts supported on mixed ZrO2-SiO2 and ZrO2-Al2O3 carriers was investigated by Fourier transform infrared spectroscopy of pyridine adsorption. Deposition of molybdenum on ZrO2-SiO2 and ZrO2-Al2O3 supports leads to formation of surface Br?nsted acid sites. The number of the Br?nsted and Lewis acid sites in supported-molybdenum catalysts depends on both the ZrO2 content and the type of the support. With increasing ZrO2 content, the Lewis acid sites increase for both series of catalysts. The Br?nsted acid sites are higher for Mo/ZrO2-SiO2 samples compared to those for Mo/ZrO2-Al2O3 and also increase with zirconia.     

Ni／ZrO2-Al2O3制备表征及催化性能的研究

本文采用浸渍沉淀法制备了不同配比的ZrO2-Al2O3复合载体。并通过浸渍法制备Ni/ZrO2-Al2O3催化剂,以苯加氢制环己烷反应为探针,考察了ZrO2与Al2O3的配比对Ni催化剂催化加氢性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、程序升温脱附(TPD)等技术考察复合载体对Ni催化剂的体相结构、还原性能以及表面吸附性能的影响。研究结果表明,ZrO2质量分数为20%的复合载体所负载的Ni催化剂有很好的加氢活性,优于单组分载体负载的Ni催化剂;采用浸渍沉淀法制备的ZrO2-Al2O3复合载体中ZrO2以非晶态形式存在,这是由于Al2O3的存在影响了ZrO2的内部结构;该载体负载的Ni催化剂较其他催化剂更容易被还原,吸附中心数量增加。     

Fe掺杂ZrO2催化剂上苯酚气相甲基化

采用共沉淀法制备了Fe掺杂的ZrO2样品,并采用X射线衍射、N2吸附-脱附、紫外漫反射光谱、扫描电镜-电子能谱、氨程序升温脱附、X射线光电子能谱和原位红外光谱进行了表征。结果表明, Fe进入ZrO2晶格中有效稳定了其晶相结构为单一的四方相。这些样品可很好地催化苯酚气相甲基化反应,其催化活性取决于Fe含量,并与样品中L酸有关。     

Models of (ZrO2)n complexes intercalated into montmorillonite

The article discusses the properties of several model zirconium dioxide complexes (ZrO(2))(n)() intercalated into the interlayer space of montmorillonite clay. Grand canonical Monte Carlo simulation was used in a series of numerical experiments during analysis of the low-temperature nitrogen adsorption in the micropores thus generated. The goal of such experiments was to determine the geometrical parameters of introduced molecular complexes of different types inside micropores of various widths. The obtained information was used to characterize textural and structural properties of three pillared interlayer materials prepared by using pillaring species synthesized via aging of zirconyl chloride solutions containing as additives chlorides of Ca, Sr, or Ba. It was found that in the cases of Ba and Ca the interlayer micropores are filled with isolated tetramers (ZrO(2))(4). Meanwhile, the presence of Sr in the pillaring solution, most likely, favors the preservation of larger sheetlike complexes (ZrO(2))(8).     

High-pressure adsorption of CO2 on NaY zeolite and model prediction of adsorption isotherms

Supercritical carbon dioxide is an efficient solvent for adsorptive separations because it can potentially be used as both the carrier solvent for adsorption and the desorbent for regeneration. Recent results have demonstrated an anomalous peak or "hump" in the adsorption isotherm near the bulk critical point when the adsorption isotherm is plotted as a function of bulk density. This work presents new data for the adsorption and desorption of carbon dioxide in the near-critical region on a crystalline, well-structured adsorbent (NaY zeolite). The results indicate a strong affinity for CO(2) as well as a significant hump near the critical point. The lattice model previously developed by Aranovich and Donohue is applied to analyze the adsorption.     

CO2 Activation by Zr+ and ZrO+ in Gas Phase

The gas-phase reduction of carbon dioxide to carbon monoxide, induced by Zr⁺ and ZrO⁺ catalysts, was investigated at density functional level of theory. Calculations were carried out using both hybrid and pure exchange-correlation functionals in order to reproduce adequately the energetic gap between the Zr^{+ 4}F and ²D electronic states and experimental reaction heats. In agreement with a guided ion beam tandem mass spectrometer study, we have found that carbon dioxide activation by Zr⁺ presents a spin-forbidden mechanism because of a spin inversion process occurring during reaction in the rate- determining step. ZrO⁺ interacts with CO₂ through two possible pathways both endothermic: formation of ZrO ₂ ⁺ and CO products is less unfavourable. Information about ground and excited states of ZrO⁺ and ZrO ₂ ⁺ oxides and bond dissociation energies of species present on the reaction paths was also given.     

负载型纳米ZrO2-Al2O3复合载体中ZrO2的负载量对Ni基催化剂性能的影响

采用真空浸渍法在负载型纳米ZrO2-Al2O3复合载体上负载NiO,并用X射线衍射考察了NiO在复合载体上的分散周值.结果表明,该分散阈值与ZrO2-Al2O3复合载体中ZrO2的负载量有关,当ZrO2的负载量为0.60 g/g时,NiO的分散阈值达到最高值0.315 g/g.热重-微分热重和程序升温脱附结果表明,NiO在不同ZrO2负载量的复合载体表面形成不同的相互作用和分布状态,复合载体中ZrO2的负载量影响催化剂表面活性中心的种类和对CO2的吸附.同时考察了不同ZrO2负载量的复合载体Ni基催化剂在CO2重整CH4反应中的活性和稳定性.     

制备方法对负载型纳米ZrO2/Al2O3复合载体性能的影响

采用浸渍-沉淀法制备了负载型纳米ZrO2/Al2O3复合载体.采用X射线衍射、N2物理吸附、差示扫描量热(DSC)和程序升温脱附等技术考察了浸渍方式和干燥方法对复合载体的表面性能、热稳定性和晶相结构的影响.结果表明,ZrO2/Al2O3复合载体中没有生成ZrO2-Al2O3复合氧化物或固溶体,纳米ZrO2仅负载在Al2O3的表面.微波干燥法制备的ZrO2/Al2O3复合载体的比表面积(158.7 m2/g)较大,最可几孔径为19.4 nm,ZrO2的粒度为4.2 nm,晶相结构为四方相ZrO2.微波诱导作用使ZrO2/Al2O3复合载体表面产生了新的酸碱中心,微波干燥法制备的ZrO2/Al2O3复合载体具有较强的热稳定性,在873~1 073 K范围内DSC曲线没有出现吸热峰,而其它干燥方法制备的复合载体在903~1 023 K范围内出现了较明显的吸热峰,表明复合载体表面的部分四方相ZrO2转变为单斜相ZrO2(m-ZrO2).对超声波处理过的复合载体进行微波干燥能进一步提高纳米ZrO2与Al2O3之间的相互作用,纳米粒子的粒度(3.4 nm)更小,分布更均匀,但没有改变ZrO2的晶相结构.     

钴基费-托合成催化剂上CO、H_2的吸附行为

采用程序升温脱附及FT-IR技术考察了CO、H2在钴基催化剂上的吸附行为.H2-TPD表明,Co/SiO2催化剂有两类脱附氢,引入锆助剂后,低温脱附氢量明显增加,高温吸附氢量下降.CO-TPD及吸附态CO的红外光谱表明锆助剂使CO在钴催化剂上的吸附强度减弱,但其吸附量增大.钴基催化剂的费-托合成反应性能可以用吸附态物种的变化来解释.     

钴基费-托合成催化剂上CO、H2的吸附行为

采用程序升温脱附及FT IR技术考察了CO、H2在钴基催化剂上的吸附行为.H2 TPD表明,Co/SiO2催化剂有两类脱附氢,引入锆助剂后,低温脱附氢量明显增加,高温吸附氢量下降.CO TPD及吸附态CO的红外光谱表明锆助剂使CO在钴催化剂上的吸附强度减弱,但其吸附量增大.钴基催化剂的费 托合成反应性能可以用吸附态物种的变化来解释.     

低温水煤气变换催化剂Cu/ZrO_2的制备、表征与性能

以水热法制得的纯单斜相ZrO2为载体,采用沉积沉淀法制备了一系列具有良好水煤气变换反应活性的Cu/ZrO2催化剂.并通过X射线粉末衍射、N2物理吸附、H2程序升温还原、X射线荧光元素分析、高分辨透射电镜和扫描电镜等手段考察了制备参数对Cu/ZrO2催化剂结构的影响,探讨了其结构与性能的关系.结果表明,CuO负载量、沉淀温度、沉淀剂种类和焙烧温度均在一定程度上影响了催化剂活性组分的晶粒大小、分散状态、织构性质及载体与活性组分间的相互作用,从而影响催化剂活性.催化剂制备的适宜条件为:CuO负载量25%,沉淀温度65oC,KOH为沉淀剂,在H2气氛300oC焙烧2h.     

Interaction of Au with thin ZrO2 films: influence of ZrO2 morphology on the adsorption and thermal stability of Au nanoparticles

The model catalysts of ZrO(2)-supported Au nanoparticles have been prepared by deposition of Au atoms onto the surfaces of thin ZrO(2) films with different morphologies. The adsorption and thermal stability of Au nanoparticles on thin ZrO(2) films have been investigated using synchrotron radiation photoemission spectroscopy (SRPES) and X-ray photoelectron spectroscopy (XPS). The thin ZrO(2) films were prepared by two different methods, giving rise to different morphologies. The first method utilized wet chemical impregnation to synthesize the thin ZrO(2) film through the procedure of first spin-coating a zirconium ethoxide (Zr(OC(2)H(5))(4)) precursor onto a SiO(2)/Si(100) substrate at room temperature followed by calcination at 773 K for 12 h. Scanning electron microscopy (SEM) investigations indicate that highly porous "sponge-like nanostructures" were obtained in this case. The second method was epitaxial growth of a ZrO(2)(111) film through vacuum evaporation of Zr metal onto Pt(111) in 1 × 10(-6) Torr of oxygen at 550 K followed by annealing at 1000 K. The structural analysis with low energy electron diffraction (LEED) of this film exhibits good long-range ordering. It has been found that Au forms smaller particles on the porous ZrO(2) film as compared to those on the ordered ZrO(2)(111) film at a given coverage. Thermal annealing experiments demonstrate that Au particles are more thermally stable on the porous ZrO(2) surface than on the ZrO(2)(111) surface, although on both surfaces, Au particles experience significant sintering at elevated temperatures. In addition, by annealing the surfaces to 1100 K, Au particles desorb completely from ZrO(2)(111) but not from porous ZrO(2). The enhanced thermal stability for Au on porous ZrO(2) can be attributed to the stronger interaction of the adsorbed Au with the defects and the hindered migration or coalescence resulting from the porous structures.