硅胶负载碳纳米管分离富集水中痕量银

以NaOH为沉淀试剂,将水样中的Ag+在线生成Ag2O沉淀,并即时被滞留在硅胶负载的碳纳米管表面。被吸附的Ag2O沉淀用HNO3(10%,V/V)洗脱,并用火焰原子吸收法检测。当进样体积为5.4mL时,线性范围为1～120μg/L,富集系数为34.5;检出限为0.35μg/L;相对标准偏差为0.5%(40μg/L,n=7),采样频率为47次/h。结果表明:本方法的富集系数、检出限及精密度均明显优于以纯碳纳米管和纯硅胶微珠为吸附剂收集Ag2O的体系。将此系统应用于实际水样中银的测定,加标回收率在96%～108%之间。     

Preparation and Characterization of Ag2 O/Organicsilicone Self-assemblied Composite Film

The composite film of nanometer AgO2/silane coupling reagent aminopropyltriethoxy-silane (CH3O)3Si(CH2)3NH2was prepared on single-crystal silicon by the self-assembly of silane on the hydroxylated substrate followed with the deposition of nanometer AgO2 on the silane SAMs from an aqueous Ag2O gel. The resultant composite film was characterized by means of X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The contact angles of distilled water on the silane SAMs and the composite film were measured to compare the surface states. The experiment shows that the nanometer Ag2O can be easily incorporated in the silane SAMs and lead to changed surface state of the composite film. Nanometer Ag2O crystallites in a size of about 20 nm distribute quite uniformly in the composite film. It was anticipated that the composite film might find application to the protection of single-crystal Si substrate in MEMS devices and also propose a novel single electron device structure based on nanoscale Ag2O colloidal particles.     

纳米B2O3/TiO2复合材料的制备及其对痕量银的分离富集性能研究与应用

制备了新型纳米B2O3/TiO2吸附材料,并采用扫描电镜(SEM)及红外光谱(IR)对其进行表征,优化了纳米B2O3/TiO2复合材料对试液中痕量银的吸附和解吸条件,建立了纳米B2O3/TiO2分离富集-原子吸收光谱测定痕量银的新方法。当pH 4.3时,在22℃下振荡20 min,Ag+能被该材料快速吸附,其静态饱和吸附容量为11.72 mg/g,吸附在纳米B2O3/TiO2上的Ag+可用0.1 mol/L HNO3-0.05 mol/L硫脲(1∶4)完全洗脱。该方法的检出限为2.01μg/L,线性范围为0.01～4.00 mg/L,相对标准偏差(RSD)为1.8%,加标回收率为95%～105%。方法应用于实际矿渣样品中痕量银的测定,结果满意。     

ZnO/Ag复合膜的制备及其润湿性转换研究

利用溶胶-凝胶技术制备了ZnO/Ag复合膜. 采用X射线粉末衍射和扫描电子显微镜对其物相组成、 晶型结构以及表面形貌进行了表征, 采用接触角测试仪对其润湿性进行了表征, 并研究了紫外光照射下Ag的掺杂量对ZnO薄膜润湿性的影响. 结果表明, 当Ag掺杂量(摩尔分数)为5%时, 所得膜的润湿性转换速率最快, 紫外光照3 h后, 其润湿性由超疏水性转换为亲水性, 黑暗中放置5 d后, 亲水性再次转换为超疏水, 实现了润湿性的可逆转换.     

Cu2O/Ag纳米复合物的表面增强拉曼光谱

用一种简单的化学还原方法制备了银纳米粒子包覆的氧化亚铜（Cu2O）纳米复合物。扫描电子显微镜显示Cu2O 为八面体型的纳米粒子,表面光滑,结构对称。包覆的Ag部分占据Cu2O粒子表面。通过比较Ag/Cu2O纳米复合物、Ag溶胶及Cu纳米粒子表面吸附的4-巯基吡啶（4-Mpy）分子表面增强拉曼光谱（SERS）发现,利用此方法得到了Cu2O粒子表面吸附分子的拉曼光谱。银纳米粒子所产生的电磁场增强又增强了吸附在Cu2O上的4-Mpy拉曼信号。这种方法为初步研究Cu2O表面吸附分子性质提供了依据,扩宽了SERS的使用范围,使SERS应用在纳米半导体材料上成为可能。     

Ni/Ag2O/RuO2-Pt阴极制备与析氢性能

以三氯化钌和氯铂酸为源物质,用溶胶凝胶法制备Ni/Ag2O/RuO2-Pt复合阴极,研究了不同涂覆液AgNO3浓度和热处理温度对该阴极析氢性能的影响.采用SEM-EDS、XRD和XPS观察阴极的表面形貌、表征其组分,结果表明,Ni/Ag2O/RuO2-Pt复合阴极表面致密,粗糙度大且裂纹少.电化学测量表明,在11 mol.L-1NaOH(90℃)溶液、0.3 A.cm-2电流密度下,Ni/Ag2O/RuO2-Pt复合阴极的析氢电位比纯Ni电极正移484 mV;交换电流密度是纯Ni电极的10倍.该阴极制备工艺简单,析氢活性高,有望降低氯碱工业的能耗.     

含氟硅丙烯酸酯乳液超疏水膜中疏水基团的梯度分布与表面微观结构研究

利用含氟疏水基团的梯度分布,结合草莓形纳米SiO2粒子提供的双重粗糙表面,制备了具有类"荷叶效应"的超疏水涂膜,水接触角达(174.2±2)°,滞后角几乎接近0°.通过原子力显微镜、扫描电镜和水接触角的测试对膜表面形貌及疏水性能进行了表征;探讨了其表面微观结构与表面疏水性能的关系.草莓形复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度,使水滴与涂膜表面接触时能够形成高的空气捕捉率,这种微观结构与疏水基团的梯度分布相结合,赋予了含氟硅丙烯酸酯乳液涂膜表面超疏水性能.     

Y2O3/Ag3VO4复合可见光催化剂的制备及其光催化性能

以Na3VO4.12H2O,AgNO3和Y(NO3)3.6H2O为原料,采用浸渍法制备了Y2O3/Ag3VO4复合可见光催化剂,并用XRD,SEM,XPS,UV-Vis等测试手段表征了试样的结构和性能。结果显示,Y2 O3/Ag3VO4复合可见光催化剂为单斜结构,Y以Y2 O3的形式分散在Ag3VO4晶体的表面。UV-Vis测试结果表明,Y2O3/Ag3VO4较纯Ag3VO4吸收带边发生了红移,在可见光区的吸收增强;以金属卤灯(波长大于400 nm)为光源,研究了Y2O3/Ag3VO4催化剂对甲基橙(MO)的可见光催化降解性能。结果发现,Y2O3/Ag3VO4复合可见光催化剂的光催化活性较纯Ag3VO4均有大幅提高,其中Y掺杂量为4%时活性最高。     

Superhydrophobic materials as efficient catalysts for hydrocarbon selective oxidation

A new type of superhydrophobic material, FP-Co-SiO(2) was prepared with organic groups immobilized on the surface of the SiO(2)-based nanocomposite. This material showed much higher catalytic activity for selective oxidation of hydrocarbons than an equivalent hydrophilic catalyst.     

Reversible superhydrophobic to superhydrophilic conversion of Ag@TiO2 composite nanofiber surfaces

A new type of superhydrophobic material consisting of a surface with supported Ag@TiO(2) core-shell nanofibers has been prepared at low temperature by plasma-enhanced chemical vapor deposition (PECVD). The fibers are formed by an inner nanocrystalline silver thread which is covered by a TiO(2) overlayer. Water contact angles depend on the width of the fibers and on their surface concentration, reaching a maximum wetting angle close to 180 degrees for a surface concentration of approximately 15 fibers microm(-2) and a thickness of 200 nm. When irradiated with UV light, these surfaces become superhydrophilic (i.e., 0 degrees contact angle). The decrease rate of the contact angle depends on both the crystalline state of the titania and on the size of the individual TiO(2) domains covering the fibers. To the best of our knowledge, this is one of the few examples existing in the literature where a superhydrophobic surface transforms reversibly into a superhydrophilic one as an effect of light irradiation.     

Silver clusters on silver sulfide nanocrystals: synthesis and behavior after electron beam irradiation

Nanocomposite crystals, (Ag)(x)(Ag(2)S)(y) with x < y, are synthesized in micellar media. The generation of Ag clusters on Ag(2)S nanocrystals is attributed to the reduction of mobile Ag(+) ions in the Ag(2)S nanocrystals by sulfur derivatives. The proportions in the composite material can be modulated by electron beam irradiation. Using dodecanethiol as surface passivating agent, 2D self-organizations of these nanocomposite crystals are produced.     

Fabrication of robust superhydrophobic coatings using PTFE‐MWCNT nanocomposite: Supercritical fluid processing

Fabrication of polymer‐carbon composite nanostructure with good dispersion of each other is critical for the desired application due to the nanostructure flaws, agglomeration, and poor absorption between the 2 materials. Fabrication of superhydrophobic surface coating composites of polytetrafluoroethylene (PTFE) with multiwalled carbon nanotubes (MWCNTs) through supercritical fluid processing was explored in this study. Homogeneity of the composite was characterized by X‐ray diffraction and Raman spectroscopy studies, which reveal that the PTFE and MWCNT are uniform in the composite. Microstructural surface evaluation of field‐emission scanning electron microscope and high‐resolution transmission electron microscope studies display that the coating composite possesses roughness structures and fibrillation of the superhydrophobic surface coating. Superhydrophobic character was evaluated on fiber‐reinforced plastic (FRP) sheets, which showed that the prepared coating composite surface showed self‐cleaning properties with a high water contact angle of 162.7°. The surface wettability was studied by increasing different temperatures (30°C to 300°C) in PTFE‐MWCNT composite, which reveals that the FRP sheets were thermally stable up to 200°C and afterward; they transformed from superhydrophobic to hydrophilic state at 250°C. The superhydrophobic surfaces are thermally stable in extreme environmental conditions, and this technique may be used and extendable for large‐scale applications.     

喷涂法制备功能性超疏水复合涂层及其性能研究

以常用工程材料硅树脂BP与St(o)ber法合成的二氧化硅(SiO2)分散液为原料,运用喷涂法(spray-coating)制备出了功能性微/纳粗糙(MNR)结构的超疏水涂层,其接触角可以达到146.5°,滚动角小于1°(测试液滴量为15μL).通过分析喷涂法制备复合涂层所需的条件,得出喷涂液pH＝7.7-8.0时,在...     

Facile Electrochemical Method for the Fabrication of Stable Corrosion-Resistant Superhydrophobic Surfaces on Zr-Based Bulk Metallic Glasses

Both surface microstructure and low surface energy modification play a vital role in the preparation of superhydrophobic surfaces. In this study, a safe and simple electrochemical method was developed to fabricate superhydrophobic surfaces of Zr-based metallic glasses with high corrosion resistance. First, micro–nano composite structures were generated on the surface of Zr-based metallic glasses by electrochemical etching in NaCl solution. Next, stearic acid was used to decrease surface energy. The effects of electrochemical etching time on surface morphology and wettability were also investigated through scanning electron microscopy and contact angle measurements. Furthermore, the influence of micro–nano composite structures and roughness on the wettability of Zr-based metallic glasses was analysed on the basis of the Cassie–Baxter model. The water contact angle of the surface was 154.3° ± 2.2°, and the sliding angle was <5°, indicating good superhydrophobicity. Moreover, the potentiodynamic polarisation test and electrochemical impedance spectroscopy suggested excellent corrosion resistance performance, and the inhibition efficiency of the superhydrophobic surface reached 99.6%. Finally, the prepared superhydrophobic surface revealed excellent temperature-resistant and self-cleaning properties.     

Titania-silver and alumina-silver composite nanoparticles: novel, versatile synthesis, reaction mechanism and potential antimicrobial application

Titania-silver (TiO(2)-Ag) and alumina-silver (Al(2)O(3)-Ag) composite nanoparticles were synthesised by a simple, reproducible, wet chemical method under ambient conditions. The surface of the oxides was modified with oleic acid, which acted as an intermediate between the oxide surface and the silver nanoparticles. The resulting composite nanoparticles were thoroughly characterised by XRD, TEM, XPS, FTIR and TGA to elucidate the mode of assembly of Ag nanoparticles on the oxide surfaces. Epoxy nanocomposites were formulated with TiO(2)-Ag and Al(2)O(3)-Ag to examine potential applications for the composite nanoparticles. Preliminary results from disc diffusion assays against Escherichia coli DH5α and Staphylococcus epidermidis NCIMB 12721 suggest that these TiO(2)-Ag and Al(2)O(3)-Ag composite nanoparticles have potential as antimicrobial materials.     

Ag修饰的Fe_3O_4/TiO_2复合磁性纳米纤维的制备及光催化性能

通过静电纺丝法制备了含有Fe3O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见光谱(UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B(Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构,Fe3O4纳米粒子均匀分布在TiO2纤维中,Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外,Fe3O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.     

二氧化硅纳米颗粒/硅树脂复合超疏水功能涂层的制备和性能研究

将二氧化硅纳米颗粒和硅树脂制成混合液,采用喷涂法(spray-coating)制备出了具备超疏水性的复合涂层.研究了二氧化硅、硅树脂不同含量配比对涂层疏水性能的影响,结果表明复合涂层的接触角随二氧化硅含量的增加而增加.在二氧化硅含量大于3%(质量分数)时,涂层显现超疏水性;当二氧化硅含量为3%(质量分数)、硅树脂含量为7%(质量分数)时,涂层与水的接触角达到151.6°,滚动角接近0°.通过扫描电子显微镜(SEM)观察涂层表面的微观结构,发现超疏水性的涂层具备微-纳复合阶层结构,类球状突起粒径在5μm左右,类球状突起上分布纳米团聚颗粒,直径约为50 nm.这种类似荷叶表面的微(纳复合阶层结构,结合硅树脂的低表面能,使得复合涂层具备了超疏水性能.     

Au/Ag2O与Ag掺杂的Au粉催化剂上CO氧化反应：Au-Ag双金属催化剂活性位

有关用于各种氧化反应中Au-Ag双金属催化剂存在显著协同效应的来源有两种观点：(1) AgOx块与体相Au表面的接触界面起重要作用,体相Au的表面是催化活性位;(2) Au-Ag双金属催化剂中形成的Au-Ag合金中电荷从Ag转移到Au上,可能对催化剂活性起作用。因此,确定Au表面上Ag是以氧化物还是以金属合金形式存在可能是深度理解该协同效应的关键。
　　为了检测和验证催化剂活性的增加是由于Ag2O与Au纳米粒子的紧密接触,在密闭循环反应体系中比较研究了Au/Ag2O和Ag2O催化剂上CO氧化反应。将CO/O2摩尔比为2的混合气通入到这二个催化剂上来跟踪压力降低的速率。因而检测了气体的消耗量和CO2的生成量。结果发现,在稳态下Au/Ag2O和Ag2O催化剂的压力降低的速率不存在差别。这两个催化剂上压力的降低是由于Ag2O中表面晶格氧被混合气中CO的还原所致。 Au/Ag2O催化剂上得到的结果与以前研究的具有氧化表面的Ag掺杂的Au粉末(Ag/Au-b)上的一致,也表明AgOx块与体相Au表面界面周边不大可能是CO氧化反应催化活性位。基于具有稳态表面的Ag/Au-b样品上的研究结果,我们认为AgOx物种被还原为0价态Ag而形成的Ag-Au合金很可能是催化活性位。     

Calcium Carbonate@silica Composite with Superhydrophobic Properties

In this paper, spherical calcium carbonate particles were prepared by using CaCl₂ aqueous solution + NH₃·H₂O + polyoxyethylene octyl phenol ether-10 (OP-10) + n-butyl alcohol + cyclohexane inverse micro emulsion system. Then, nanoscale spherical silica was deposited on the surface of micron calcium carbonate by Stöber method to form the composite material. Scanning electron microscope (SEM), X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS) were used to characterize the morphology and structure of the composite material. It is found that the surface of the composite material has a micro-nano complex structure similar to the surface of a “lotus leaf”, making the composite material show hydrophobicity. The contact angle of the cubic calcium carbonate, spherical calcium carbonate and CaCO₃@SiO₂ composite material were measured. They were 51.6°, 73.5°, and 76.8°, respectively. After modification with stearic acid, the contact angle of cubic and spherical CaCO₃ were 127.1° and 136.1°, respectively, while the contact angle of CaCO₃@SiO₂ composite was 151.3°. These results showed that CaCO₃@SiO₂ composite had good superhydrophobicity, and the influence of material roughness on its hydrophobicity was investigated using the Cassie model theory.     

无机-高分子-无机多组分核壳纳米复合材料的制备和表征

Fe₃O₄ nanoparticles were prepared by chemical co-precipitation using palmitic acid as surfactant， then a uniformly dispersed system of Fe₃O₄@Polymethylmethacrylates(PMMA) core-shell structure was obtained. Furtherm-ore， polymethylmethacrylates(PNIPAM) was encapsulated on the surface of the Fe₃O₄@PMMA core-shell nano-structure to get Fe₃O₄@PMMA@PNIPAM double shell-core composite structure. After that， the Ag nano-particles were assembled on the surface of Fe₃O₄@PMMA@PNIPAM taking advantage of coordination reaction between Ag⁺ and nitrogen atom on the amide group of PNIPAM. The magnetism of composites is convenient for the catalyst separation from the solution.