La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La1-xCaxMnO3(x=0~0.4)纳米颗粒,X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高,颗粒平均粒径约40 nm。在0.1 mol.L-1KOH水溶液中进行的氧还原电催化性能测试显示,La0.7Ca0.3MnO3样品催化活性最高,表观电子转移数接近4,还原电流密度与Pt/C催化剂相当,而催化稳定性优于Pt/C。进一步研究了La1-xCaxMnO3样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响,结果表明当x=0.3时,催化剂中Mn处于混合价态,Mn-O键长适中,最有利于电催化反应。     

La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La_1-xCa_xMnO₃(x=0~0.4)纳米颗粒, X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高, 颗粒平均粒径约40 nm。在0.1 mol·L^-1 KOH水溶液中进行的氧还原电催化性能测试显示, La_0.7Ca_0.3MnO₃样品催化活性最高, 表观电子转移数接近4, 还原电流密度与Pt/C催化剂相当, 而催化稳定性优于Pt/C。进一步研究了La_1-xCa_xMnO₃样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响, 结果表明当x=0.3时, 催化剂中Mn处于混合价态, Mn-O键长适中, 最有利于电催化反应。     

Properties of the perovskites, SrMn1−xFexO3−δ (x=1/3, 1/2, 2/3)

The SrMn_1−xFe_xO_3−δ (x=1/3, 1/2, 2/3) phases have been prepared and are shown by powder X-ray and neutron (for x=1/2) diffraction to adopt an ideal cubic perovskite structure with a disordered distribution of transition-metal cations over the six-coordinate B-site. Due to synthesis in air, the phases are oxygen deficient and formally contain both Fe³⁺ and Fe⁴⁺. Magnetic susceptibility data show an antiferromagnetic transition at 180 and 140 K for x=1/3 and 1/2, respectively and a spin-glass transition at 5, 25, 45 K for x=1/3, 1/2 and 2/3, respectively. The magnetic properties are explained in terms of super-exchange interactions between Mn⁴⁺, Fe^(4+δ)+ and Fe⁽³⁺⁾⁺. The XAS results for the Mn-sites in these compounds indicate small Mn-valence changes, however, the Mn-pre-edge spectra indicate increased localization of the Mn-e_g orbitals with Fe substitution. The Mössbauer results show the distinct two-site Fe⁽³⁺⁾+/Fe^(4+δ)+ disproportionation in the Mn- substituted materials with strong covalency effects at both sites. This disproportionation is a very concrete reflection of a localization of the Fe-d states due to the Mn-substitution.     

Positron lifetime study of Pr1−xCaxMnO3 (x=0.5, 0.3) during magnetic transition

We measured the positron lifetime in perovskite manganites Pr_1−xCa_xMnO₃ (x=0.3, 0.5). Two lifetime components were observed for each compound; they were attributed to the annihilation of free positrons and positrons trapped at the A-site vacancies. The positron lifetime at the A-site vacancies changed significantly during the antiferromagnetic transition in both the compounds, whereas it was constant around the charge-ordering transition. This change indicates that the electron distribution at the vacancies changed possibly due to the change in the electron distribution of neighboring oxygen atoms. This result indicates that positron lifetime measurements can provide unique information on electronic states during a spin-related phase transition in various oxide materials.     

Preparation, characterization and the standard enthalpy of formation of La0.95MnO3+δ and Sm0.95MnO3+δ

Among the perovskites, the rare earth manganites find application in several electrochemical devices because of their enhanced thermodynamic stability. In this paper, we present the results obtained on the preparation and characterization of La_0.95MnO_3+δ and Sm_0.95MnO_3+δ which were prepared by the solid state and sol–gel methods. XRD characterization of the manganites indicated that the crystal structure depends on the method of preparation and heat treatments. The ratio of Mn³⁺ to Mn⁴⁺ in these samples also depended on the method of preparation and heat treatments, as indicated by thermogravimetric (TG) and temperature programmed reduction (TPR) studies in Ar + 5% H₂ atmosphere. The standard molar enthalpy of formation, which is a measure of the thermodynamic stability of these compounds were determined using an isoperibol calorimeter.     

A TEM, XRD, and crystal chemical investigation of oxygen/vacancy ordering in (Ba1−xLax)2In2O5+x, 0x0.6

A careful TEM and XRD study of the (Ba_1−xLa_x)₂In₂O_5+x, 0x0.6, ‘defect-perovskite’-type solid solution has been carried out. A well-defined structural phase transition is shown to occur between x=0.1 and 0.2 from the orthorhombic brownmillerite structure type on the low x side to a multiple twinned, tetragonal 1×1×2 perovskite-related superstructure phase on the high x side at x=0.2. This phase transition correlates with an important phase transition previously observed in electrical conductivity versus temperature measurements. The existence of additional satellite reflections close to the regions of reciprocal space was found to be typical of all (Ba_1−xLa_x)₂In₂O_5+x specimens, although their intensity relative to the parent Bragg reflections systematically reduces as x increases. As x increases beyond 0.2, the -type satellite reflections initially become weaker and rather more diffuse for x=0.3 before splitting into pairs of rather weak and somewhat diffuse incommensurate satellite reflections for x=0.4 and beyond. An interpretation in terms of oxygen vacancy ordering and associated structural relaxation is given. Additional structured diffuse scattering is also observed and a tentative explanation in terms of Ba/La ordering and associated local strain distortions put forward.     

Thermoelectric properties of Cu-doped n-type (Bi2Te3)0.9–(Bi2−xCuxSe3)0.1(x=0–0.2) alloys

n-Type (Bi₂Te₃)_0.9–(Bi_2−xCu_xSe₃)_0.1 (x=0–0.2) alloys with Cu substitution for Bi were prepared by spark plasma-sintering technique and their structural and thermoelectric properties were evaluated. Rietveld analysis reveals that approximate 9.0% of Bi atomic sites are occupied by Cu atoms and less than 4.0 wt% second phase Cu_2.86Te₂ precipitated in the Cu-doped parent alloys. Measurements show that an introduction of a small amount of Cu (x0.1) can reduce the lattice thermal conductivity (κ_L), and improve the electrical conductivity and Seebeck coefficient. An optimal dimensionless figure of merit (ZT) value of 0.98 is obtained for x=0.1 at 417 K, which is obviously higher than those of Cu-free Bi₂Se_0.3Te_2.7 (ZT=0.66) and Ag-doped alloys (ZT=0.86) prepared by the same technologies.     

Analysis of structural and magnetic phase transition behaviors of La1−xSrxCrO3 by measurement of heat capacity with thermal relaxation technique

The heat capacity, C_p, of the La_1−xSr_xCrO₃ system and its temperature dependence have been measured by a thermal relaxation technique. Both structural and magnetic phase transitions were detected at temperatures that can be surmised from the phase diagram proposed in previous studies. The observed variation in enthalpy after the first-order structural phase transition, ΔH, showed agreement with those measured by differential scanning calorimetry (DSC). A decrease in the variation in C_p in the second-order magnetic phase transition, ΔC_p, with an increase in Sr content was detected, which can be attributed to a decrease in electronic spin configuration entropy with an increase in Sr content. In the dependence of ΔC_p on Sr content, a bending point was also observed at x  0.12, at which the crystal system varies from an orthorhombic-distorted perovskite structure to a rhombohedral-distorted perovskite structure.     

Enhanced ferromagnetic transition and magnetoresistance in granular Ag-added La0.7Ca0.3MnO3

Granular Ag-added La_0.7Ca_0.3MnO₃ (LCMO) samples were prepared by a sol-gel chemical route. Significant enhancements in Curie temperature (T_C), metal−insulator transition (T_p) and magnetoresistance (MR) effects near room temperature are observed in as-obtained samples. 10 wt% addition of Ag in LCMO causes T_C shift from 272 to 290 K, T_p boost up for more than 100 K and resistivity decrease by more than 3 orders of magnitude. X-ray diffraction patterns, thermal analysis and energy dispersive analysis of X-rays evidently show the existence of metal silver in LCMO matrices. High-resolution electron microscopy illustrates a well crystallization for LCMO grains in existence of Ag. It is argued that improved grain boundary effect and better crystallization caused by Ag addition are responsible for the enhancements.     

Preparation and characterization of lithium ion-conducting glass-ceramics in the Li1 + xCrxGe2 − x(PO4)3 system

Li₂O–Cr₂O₃–GeO₂–P₂O₅ based glasses were synthesized by a conventional melt-quenching method and successfully converted into glass-ceramics through heat treatment. Experimental results of DTA, XRD, ac impedance techniques and FESEM indicated that Li_1.4Cr_0.4Ge_1.6(PO₄)₃ glass-ceramics treated at 900 °C for 12 h in the Li_1 + xCr_xGe_2 − x(PO₄)₃ (x = 0–0.8) system exhibited the best glass stability against crystallization and the highest ambient conductivity value of 6.81 × 10⁻⁴ S/cm with an activation energy as low as 26.9 kJ/mol. In addition, the Li_1.4Cr_0.4Ge_1.6(PO₄)₃ glass-ceramics displayed good chemical stability against lithium metal at room temperature. The good thermal and chemical stability, excellent conducting property, easy preparation and low cost make it promising to be used as solid-state electrolytes for all-solid-state lithium batteries.     

Effect of strontium substitution on the activity of La2?xSrxNiO4 (x = 0.0–1.2) in NO decomposition

The aim of this work is to study the effect of Sr substitution on the redox properties and catalytic activity of La_2−x Sr _x NiO₄ (x = 0.0–1.2) for NO decomposition. Results suggest that the x = 0.6 sample shows the highest activity. The characterization (TPD, TPR, etc.) of samples indicates that the x = 0.6 sample possesses suitable abilities in both oxidation and reduction, which facilitates the proceeding of oxygen desorption and NO adsorption. At temperature below 700°C, the oxygen desorption is difficult, and is the rate-determining step of NO decomposition. With the increase of reaction temperature (T > 700°C), the oxygen desorption is favorable and, the active adsorption of NO on the active site (NO + V _o + Ni²⁺ → NO⁻-Ni³⁺) turns out to be the rate-determining step. The existence of oxygen vacancy is the prerequisite condition for NO decomposition, but its quantity does not relate much to the activity. Supported by the National Hi-Tech Research and Development Program of China (863 Program)(Grant No. 2004CB 719502) and the National Natural Science Foundation of China (Grant No. 20177022)     

The metastable Ni7±xS6, and mixed Ni6±x(S1−ySey)5, phases

The closely related, narrowly non-stoichiometric, metastable as well as thermodynamically stable “phases” in the metal-rich part of the Ni–S phase diagram near the nominal composition Ni_7±xS₆ have been carefully re-investigated via electron diffraction and transmission electron microscope imaging. Two quite distinct polymorphs have been identified, a minority incommensurate interface-modulated polymorph and a (heavily twinned) majority I1a1, a=2a_p, b=2b_p, c=−a_p+c_p superstructure (of an underlying Bmmb, a_p3.3, b_p16.4, c_p11.3 Å parent structure) polymorph. The incommensurate polymorph is shown to be very closely related to the only known polymorph of Ni_6±xSe₅ and is rapidly stabilized to room temperature upon doping of the sulfide compounds with selenium.     

High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte based PCMFCs with stable Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 μm in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm⁻², and a low polarization resistance of the electrodes of 0.08 Ω cm² was achieved at 700 °C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells.     

正极材料Li(Ni0.5Mn0.5)1-xMxO2 (M=Ti，Al；x=0，0.02)电化学行为的比较研究

0IntroductionMany efforts have been made to develop newmaterials as an alternative to LiCoO2due to the rela-tively high cost and toxicity of Co.Much attention hasbeen paid to layered structure cathode materials suchas LiMnO2and LiNiO2due to their lower co…     

Synthesis and ac susceptibility of YCa2Cu3O7−δ

The bulk superconducting YCa₂Cu₃O_7−δ compounds are prepared at an ordinary pressure of oxygen by conventional solid-state reaction method. The formation of sample is tested by means of XRD and is studied for their ac susceptibility below room temperature up to 77.5 K. The samples are found single-phase orthorhombic structure and found superconducting at 83.5 K. It is shown that the analysis is consistent with published data on YBa₂Cu₃O_7−δ oxide superconductor.     

La1-xCaxMnO3外延薄膜的制备、结构及磁电阻效应

采用溶胶-凝胶旋涂法在单晶LaAlO3 (100)基片上生长了La1-xCaxMnO3(x=0, 0.05, 0.1, 0.2)外延薄膜. 利用X射线衍射仪(XRD)、 原子力显微镜(AFM)、 聚焦离子束系统(FIB)、 X射线光电子能谱分析仪(XPS)、 振动样品磁强计(VSM)和磁性测量系统(MPMS)对样品的结构、 形貌、 价态、 居里温度和磁电阻效应进行了研究. 结果表明, 薄膜为立方钙钛矿结构, 具有明显的(100)外延生长取向和平整的表面. 在居里温度附近, 样品发生铁磁-顺磁转变. 随着Ca2+掺杂量的增加, 样品的居里温度升高, La0.8Ca0.2MnO3的居里温度为264 K. 随温度的变化, 样品发生了金属-绝缘体转变. 样品还具有较大的磁电阻效应, 在H=2.0 T, T=210 K时, La0.95Ca0.05MnO3的磁电阻达到80.9%.     

Transport Properties of Bi2−xInxSe3 Single Crystals

The paper reports on the temperature dependence of the electrical and thermal conductivity, Hall constant, and Seebeck coefficient of Bi_2−xIn_xSe₃ (x=0, 0.2, 0.4) single crystals measured over the temperature range from 2 to 300 K. One single-valley conduction band model is used to interpret relations among transport coefficients. The data analysis relies on the use of a mixed carrier scattering mechanism consisting of acoustic scattering and scattering on ionized impurities. The effect of In incorporation into the Bi₂Se₃ crystal lattice on the individual components of thermal conductivity is evaluated and discussed.     

固-溶法制备中温固体氧化物燃料电池高性能La0.8Sr0.2MnO3-Ba0.5Sr0.5Co0.8Fe0.2O3阴极

研究了新型固溶法合成La_0.8Sr_0.2MnO₃（LSM）包覆Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃（BSCF）复合粉体（LSM-BSCF）,并探讨了其作为中温固体氧化物燃料电池阴极材料的电化学性能。LSM-BSCF阴极结合了LSM和BSCF阴极的优点,不仅增大了三相界面,而且稳定了微观结构。当温度为600-750℃时,其极化阻抗为0.61-0.09 Ω·cm²。与溶液注入法制备的高性能电极相比,极大地提高了性能稳定性。     

Effect of annealing temperature on the structural and optical properties of Zn1−xMgxO particles prepared by oxalate precursor

Zn_1−xMg_xO particles were prepared using zinc and magnesium oxalate precursor by co-precipitated method. The lattice constants of Zn_1−xMg_xO proved that the interstitial Mg formed at 500 °C and Mg replaced Zn in ZnO tetrahedral coordination at 800 °C. Compared with the ZnO, the absorbing band edge of the Zn_1−xMg_xO displayed blue shifts. The room temperature photoluminescence was similar to ZnO and variation of Mg content did not change the shape or peak position of the emission spectra markedly when it was annealed at 500 °C. However, its blue emission band disappeared, and a relatively strong green light emission at 498 nm appeared after annealed at 800 °C. The photoluminescence intensity ratios I_(green)/I_(UV) of Zn_1−xMg_xO varied with Mg content and the green light emission peak shifted from 498 nm to 472 nm when Mg content increased from 0 to 2.0 at.%.     

Preparation and hydrogen permeation of SrCe0.95Y0.05O3−δ asymmetrical membranes

Asymmetrical thin membranes of SrCe_0.95Y_0.05O_3−δ (SCY) were prepared by a conventional and cost-effective dry pressing method. The substrate consisted of SCY, NiO and soluble starch (SS), and the top layer was the SCY. NiO was used as a pore former and soluble starch was used to control the shrinkage of the substrate to match that of the top layer. Crack-free asymmetrical thin membranes with thicknesses of about 50 μm and grain sizes of 5–10 μm were successfully pressed on to the substrates. Hydrogen permeation fluxes (J_H2) of these thin membranes were measured under different operating conditions. At 950 °C, J_H2 of the 50 μm SCY asymmetrical membrane towards a mixture of 80% H₂/He was as high as 7.6 × 10⁻⁸ mol/cm² s, which was about 7 times higher than that of the symmetrical membranes with a thickness of about 620 μm. The hydrogen permeation properties of SCY asymmetrical membranes were investigated and activation energies for hydrogen permeation fluxes were calculated. The slope of the relationship between the hydrogen permeation fluxes and the thickness of the membranes was −0.72, indicating that permeation in SCY asymmetric membranes was controlled by both bulk diffusion and surface reaction in the range investigated.