Effect of ethylene carbonate plasticizer and TiO<Subscript>2</Subscript> nanoparticles on 49% poly(methyl methacrylate) grafted natural rubber-based polymer electrolyte

The effect of plasticizer and TiO₂ nanoparticles on the conductivity, chemical interaction and surface morphology of polymer electrolyte of MG49–EC–LiClO₄–TiO₂ has been investigated. The electrolyte films were successfully prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by sol-gel process and was added into the MG49–EC–LiClO₄ electrolyte system. Alternating current electrochemical impedance spectroscopy was employed to investigate the ionic conductivity of the electrolyte films at 25 °C, and the analysis showed that the addition of TiO₂ filler and ethylene carbonate (EC) plasticizer has increased the ionic conductivity of the electrolyte up to its optimum level. The highest conductivity of 1.1 × 10⁻³ Scm⁻¹ was obtained at 30 wt.% of EC. Fourier transform infrared spectroscopy measurement was employed to study the interactions between lithium ions and oxygen atoms that occurred at carbonyl (C=O) and ether (C-O-C) groups. The scanning electron microscopy micrograph shows that the electrolyte with 30 wt.% EC posses the smoothest surface for which the highest conductivity was obtained.     

Structural and electrical properties of pure and H<Subscript>2</Subscript>SO<Subscript>4</Subscript> doped (PVA)<Subscript>0.7</Subscript>(NaI)<Subscript>0.3</Subscript> solid polymer electrolyte

Solid polymer electrolytes (SPE) based on poly-(vinyl alcohol) (PVA)_0.7 and sodium iodide (NaI)_0.3 complexed with sulfuric acid (SA) at different concentrations were prepared using solution casting technique. The structural properties of these electrolyte films were examined by X-ray diffraction (XRD) studies. The XRD data revealed that sulfuric acid disrupt the semi-crystalline nature of (PVA)_0.7(NaI)_0.3 and convert it into an amorphous phase. The proton conductivity and impedance of the electrolyte were studied with changing sulfuric acid concentration from 0 to 5.1 mol/liter (M). The highest conductivity of (PVA)_0.7(NaI)_0.3 matrix at room temperature was 10⁻⁵ S cm⁻¹ and this increased to 10⁻³ S cm⁻¹ with doping by 5.1 M sulfuric acid. The electrical conductivity (σ) and dielectric permittivity (ε′) of the solid polymer electrolyte in frequency range (500 Hz–1 MHz) and temperature range (300–400) K were carried out. The electrolyte with the highest electrical conductivity was used in the fabrication of a sodium battery with the configuration Na/SPE/MnO₂. The fabricated cells give open circuit voltage of 3.34 V and have an internal resistance of 4.5 kΩ.     

Performance of lithium-ion cells using 1 M LiPF<Subscript>6</Subscript> in EC/DEC (<Emphasis Type="Italic">v</Emphasis>/<Emphasis Type="Italic">v</Emphasis> = 1/2) electrolyte with ethyl propionate additive

In this work, 1 M LiPF₆:EC:DEC (v/v = 1/2) was used as a baseline electrolyte where EC is ethylene carbonate and DEC is diethyl carbonate. Ethyl propionate (EP) was used as an additive. The conductivity of the liquid electrolyte was obtained at ambient and elevated temperatures. The highest room temperature conductivity was observed at (8.05 ± 0.16) mS cm⁻¹ for the electrolyte containing 28.6 vol.% EP. Viscosity of the baseline and EP added baseline electrolytes have been measured at room and elevated temperatures. The electrolyte was also characterized by linear sweep voltammetry. The highest conducting electrolyte with 28.6 vol.% EP and the baseline electrolyte were used to fabricate several batteries. The batteries were charged and discharged at room temperature and at −20°C.     

Conductivity, dielectric behaviour and thermal stability studies of lithium ion dissociation in poly(methyl methacrylate)-based gel polymer electrolytes

Thin films of poly(methyl methacrylate) (PMMA) with lithium triflate (LiCF₃SO₃) were prepared by using the solution-casting method with PMMA as the host polymer. Ionic conductivity and dielectric measurements were carried out on these films. The highest conductivity for polymer electrolyte with a ratio of 65:35 was found to be 9.88 × 10⁻⁵ S cm⁻¹, which is suitable for the production of mobile phone battery. Thermal gravimetric analysis was carried out to evaluate the thermal stability of the polymer electrolyte. The addition of salts will increase thermal stability of the polymer electrolyte.     

Impedance and FTIR studies on plasticized PMMA–LiN(CF<Subscript>3</Subscript>SO<Subscript>2</Subscript>)<Subscript>2</Subscript> nanocomposite polymer electrolytes

Plasticized polymer electrolytes composed of poly(methyl methacrylate) (PMMA) as the host polymer and lithium bis(trifluoromethanesulfonyl)imide LiN(CF₃SO₂)₂ as a salt were prepared by solution casting technique at different ratios. The ionic conductivity varied slightly and exhibited a maximum value of 3.65 × 10⁻⁵ S cm⁻¹ at 85% PMMA and 15% LiN(CF₃SO₂)₂. The complexation effect of salt was investigated using FTIR. It showed some simple overlapping and shift in peaks between PMMA and LiN(CF₃SO₂)₂ salt in the polymer electrolyte. Ethylene carbonate (EC) and propylene carbonate (PC) were added to the PMMA–LiN(CF₃SO₂)₂ polymer electrolyte as plasticizer to enhance the conductivity. The highest conductivities obtained were 1.28 × 10⁻⁴ S cm⁻¹ and 2.00 × 10⁻⁴ S cm⁻¹ for EC and PC mixture system, respectively. In addition, to improve the handling of films, 1% to 5% fumed silica was added to the PMMA–LiN(CF₃SO₂)₂–EC–PC solid polymer electrolyte which showed a maximum value at 6.11 × 10⁻⁵ S cm⁻¹ for 2% SiO₂.     

Effect of lithium salt concentration in PVAc/PMMA-based gel polymer electrolytes

Hybrid solid polymer electrolyte films comprising of poly(vinyl acetate) (PVAc), poly(methyl methacrylate) (PMMA), LiClO₄, and propylene carbonate are prepared by solution casting technique by varying the salt concentration. In this study, PVAc/PMMA polymer blend ratio is fixed as 25:75 on the basis of conductivity and mechanical stability of the film. X-ray diffraction, Fourier transform infrared impedance, thermogravimetry/differential thermal analysis and scanning electron microscopy studies are carried out for the polymer electrolytes. The maximum ionic conductivity is found to be 4.511 × 10⁻⁴ S cm⁻¹ at 303 K for the plasticized polymer electrolyte with 8 wt.% of LiClO₄. The ionic conductivity is found to decrease with an increase of LiClO₄ concentration.     

Electrical and structural properties of poly (ethylene oxide)/silver triflate polymer electrolyte system dispersed with MgO nanofillers

Solvent-free films of poly (ethylene oxide)–silver triflate (PEO–AgCF₃SO₃)/MgO-based nanocomposite polymer electrolytes (PEO)₅₀AgCF₃SO₃–x wt.% MgO (x = 1, 3, 5, 7, and 10) obtained using solution casting technique were found to exhibit an appreciably good complexation of MgO nanofiller within the polymer electrolyte system and non-Debye type of relaxation as revealed by Fourier transform infrared and complex impedance analyses. Optimized filler (5 wt.% MgO) when incorporated into the polymer electrolyte resulted in a maximum electrical conductivity of 2 × 10⁻⁶ S cm⁻¹ in conjunction with a silver ionic transference number (t _Ag+) of 0.23 at room temperature (298 K). Detailed structural, thermal, and surface morphological investigation indicated a slight reduction in the degree of crystallinity owing to the addition of MgO nanofiller.     

Conductivity studies of plasticized anhydrous PEO-KOH alkaline solid polymer electrolyte

Polyethylene oxide (PEO)–potassium hydroxide (KOH)-based alkaline solid polymer electrolyte films have been prepared by using methanol as solvent. The highest room temperature ionic conductivity of (2.1 ± 0.5) × 10⁻⁸ S cm⁻¹ was achieved for the composition of 70 wt% PEO:30 wt% KOH. The addition of plasticizer, ethylene carbonate, propylene carbonate, or polyethylene glycol to the highest conductivity of PEO–KOH system helps to increase the ambient ionic conductivity to the order of 10⁻⁶–10⁻⁴ S cm⁻¹. The log σ vs 1/T plot of PEO–KOH showed a small conductivity decrease at 50–60 °C range. The small decrease and the hysteresis that occur during the heating–cooling cycle was overcome by the presence of the plasticizer. X-ray diffraction observation supports the conductivity results.     

Ionic transport, thermal, XRD, and phase morphological studies on LiCF3SO3-based PVC–PVdF gel electrolytes

The plasticized polymer electrolyte composed of polyvinylchloride (PVC) and polyvinylidene fluoride (PVdF) as host polymer, the mixture of ethylene carbonate and propylene carbonate as plasticizer, and LiCF₃SO₃ as a salt was studied. The effect of the PVC-to-PVdF blend ratio with the fixed plasticizer and salt content on the ionic conduction was investigated. The electrolyte films reveal a phase-separated morphology due to immiscibility of the PVC with plasticizer. Among the three blend ratios studied, 3:7 PVC–PVdF blend ratio has shown enhanced ionic conductivity of 1.47 × 10⁻⁵ S cm⁻¹ at ambient temperature, i.e., the ionic conductivity decreased with increasing PVC-to-PVdF ratio and increased with increasing temperature. A temperature dependency on ionic conductivity obeys the Arrhenius behavior. The melting endotherms corresponding to vinylidene (VdF) crystalline phases are observed in thermal analysis. Thermal study reveals the different levels of uptake of plasticizer by VdF crystallites. The decrease in amorphousity with increase in PVC in X-ray diffraction studies and larger pore size appearance for higher content of PVC in scanning electron microscopy images support the ionic conductivity variations with increase in blend ratios.     

Dielectric relaxation and dc conductivity on the PVOH-CF3COONH4 polymer system

In the present paper, the ionic conductivity and the dielectric relaxation properties on the poly(vinyl alcohol)-CF₃COONH₄ polymer system have been investigated by means of impedance spectroscopy measurements over wide ranges of frequencies and temperatures. The electrolyte samples were prepared by solution casting technique. The temperature dependence of the sample’s conductivity was modeled by Arrhenius and Vogel-Tammann-Fulcher (VTF) equations. The highest conductivity of the electrolyte of 3.41×10^− 3 (Ωcm)^− 1 was obtained at 423 K. For these polymer system two relaxation processes are revealed in the frequency range and temperature interval of the measurements. One is the glass transition relaxation (α-relaxation) of the amorphous region at about 353 K and the other is the relaxation associated with the crystalline region at about 423 K. Dielectric relaxation has been studied using the complex electric modulus formalism. It has been observed that the conductivity relaxation in this polymer system is highly non-exponential. From the electric modulus formalism, it is concluded that the electrical relaxation mechanism is independent of temperature for the two relaxation processes, but is dependent on composition.     

Effect of ZnO nanoparticles filler concentration on the properties of PEO-ENR50-LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript> solid polymeric electrolyte

A solid polymer electrolyte comprising blend of poly(ethylene oxide) and 50% epoxidized natural rubber (ENR50) as a polymer host, LiCF₃SO₃ as a salt and nanoparticle ZnO as an inorganic filler was prepared by solution-casting technique. The effect of filler on the electrolyte properties was characterized and analysed. FESEM analysis showed that the filler was well distributed in the polymer matrix, while the effective interaction between the salt and the polymer host was reduced by the addition of filler. As evidenced by FTIR analysis, which showed the formation of triplet peak at C-O-C stretching region. Ionic conductivity was found to decrease from 1.4 × 10⁻⁴ Scm⁻¹ to 2.5 × 10⁻⁶ Scm⁻¹ upon the addition of filler, due to the blocking effect of filler into the electrolyte conduction pathways. The temperature dependence on the electrolyte conductivity obeys Arrhenius rule in two temperature regions.     

AC impedance, FTIR and XRD investigations of poly acrylonitrile complexed with LiCF3SO3

Solid polymer electrolytes of high ionic conductivity are prepared using poly acrylonitrile (PAN), propylene carbonate (PC), ethylene carbonate (EC) and LiCF₃SO₃. The polymer films are characterised by X-ray diffraction, FTIR and a.c. impedance spectroscopic techniques. The conductivity studies of PAN-LiCF₃SO₃-PC-EC polymer electrolyte systems are carried out in the temperature range 301–373 K. The temperature dependence of the conductivity of the polymer films obeys the VTF relation. The conductivity values are presented and the results are discussed.     

Effect of plasticizer on structural and electrical properties of nanocomposite solid polymer electrolytes

The solid polymer electrolyte films based on polyethylene oxide, NaClO₄ with dodecyl amine modified montmorillonite as filler, and polyethylene glycol as plasticizer were prepared by a tape casting method. The effect of plasticization on structural, microstructural, and electrical properties of the materials has been investigated. A systematic change in the structural and microstructural properties of plasticized polymer nanocomposite electrolytes (PPNCEs) on addition of plasticizer was observed in our X-ray diffraction pattern and scanning electron microscopy micrographs. Complex impedance analysis technique was used to calculate the electrical properties of the nanocomposites. Addition of plasticizer has resulted in the lowering of the glass transition temperature, effective dissociation of the salt, and enhancement in the electrical conductivity. The maximum value of conductivity obtained was ∼4.4 × 10⁻⁶ S cm⁻¹ (on addition of ∼20% plasticizer), which is an order of magnitude higher than that of pure polymer nanocomposite electrolyte films (2.82 × 10⁻⁷ S cm⁻¹). The enhancement in conductivity on plasticization was well correlated with the change in other physical properties.     

Conductivity studies of starch-based polymer electrolytes

A proton-conducting polymer electrolyte based on starch and ammonium nitrate (NH₄NO₃) has been prepared through solution casting method. Ionic conductivity for the system was conducted over a wide range of frequency between 50 Hz and 1 MHz and at temperatures between 303 K and 373 K. Impedance analysis shows that sample with 25 wt.% NH₄NO₃ has a smaller bulk resistance (R _b) compared to that of the pure sample. The amount of NH₄NO₃ was found to influence the proton conduction; the highest obtainable room temperature conductivity was 2.83 × 10⁻⁵ S cm⁻¹, while at 100 °C, the conductivity in found to be 2.09 × 10⁻⁴ S cm⁻¹. The dielectric analysis demonstrates a non-Debye behavior. Transport parameters of the samples were calculated using the Rice and Roth model and thus shows that the increase in conductivity is due to the increase in the number of mobile ions.     

A novel PEO-based composite polymer electrolyte with NaAlOSiO molecular sieves powders

Ion-conducting thin film polymer electrolytes based on poly(ethylene oxide) (PEO) complexes with NaAlOSiO molecular sieves powders has been prepared by solution casting technique. X-ray diffraction, scanning electron microscopy, differential scanning calorimeter, and alternating current impedance techniques are employed to investigate the effect of NaAlOSiO molecular sieves on the crystallization mechanism of PEO in composite polymer electrolyte. The experimental results show that NaAlOSiO powders have great influence on the growth stage of PEO spherulites. PEO crystallization decrease and the amorphous region that the lithium-ion transport is expanded by adding appropriate NaAlOSiO, which leads to drastic enhancement in the ionic conductivity of the (PEO)₁₆LiClO₄ electrolyte. The ionic conductivity of (PEO)₁₆LiClO₄-12 wt.% NaAlOSiO achieves (2.370 ± 0.082) × 10⁻⁴ S · cm⁻¹ at room temperature (18 °C). Without NaAlOSiO, the ionic conductivity has only (8.382 ± 0.927) × 10⁻⁶ S · cm⁻¹, enhancing 2 orders of magnitude. Compared with inorganic oxide as filler, the addition of NaAlOSiO molecular sieves powders can disperse homogeneously in the electrolyte matrix without forming any crystal phase and the growth stage of PEO spherulites can be hindered more effectively.     

Ionic conduction behavior in PVC–PEG blend polymer electrolytes upon the addition of TiO2

The blend-based polymer electrolyte consisting of poly (vinyl chloride) (PVC) and poly (ethylene glycol) (PEG) as host polymers and lithium perchlorate (LiClO₄) as the complexing salt was studied. An attempt was made to investigate the effect of TiO₂ concentration in the unplasticized PVC–PEG polymer electrolyte system. The XRD and FTIR studies confirm the formation of a polymer–salt complex. The conductivity results indicate that the incorporation of ceramic filler up to a certain concentration (15 wt.%) increases the ionic conductivity and upon further addition the conductivity decreases. The maximum ionic conductivity 0.012 × 10⁻⁴ S cm⁻¹ is obtained for PVC–PEG–LiClO₄–TiO₂ (75–25–5–15) system. Thermal stability of the polymer electrolyte is ascertained from TG/DTA studies.     

Studies on PEO-based sodium ion conducting composite polymer films

A sodium ion conducting composite polymer electrolyte (CPE) prepared by solution-caste technique by dispersion of an electrochemically inert ceramic filler (SnO₂) in the PEO–salt complex matrix is reported. The effect of filler concentration on morphological, electrical, electrochemical, and mechanical stability of the CPE films has been investigated and analyzed. Composite nature of the films has been confirmed from X-ray diffraction and scanning electron microscopy patterns. Room temperature d.c. conductivity observed as a function of filler concentration indicates an enhancement (maximum) at 1–2 wt% filler concentration followed by another maximum at ∼10 wt% SnO₂. This two-maxima feature of electrical conductivity as a function of filler concentration remains unaltered in the CPE films even at 100 °C (i.e., after crystalline melting), suggesting an active role of the filler particles in governing electrical transport. Substantial enhancement in the voltage stability and mechanical properties of the CPE films has been noticed on filler dispersion. The composite polymer films have been observed to be predominantly ionic in nature with t _ion ∼ 0.99 for 1–2 wt% SnO₂. However, this value gets lowered on increasing addition of SnO₂ with t _ion ∼ 0.90 for 25 wt% SnO₂. A calculation of ionic and electronic conductivity for 25 wt% of SnO₂ film works out to be ∼2.34 × 10⁻⁶ and 2.6 × 10⁻⁷ S/cm, respectively.     

Effects of MnO<Subscript>2</Subscript> nano-particles on the conductivity of PMMA-PEO-LiClO<Subscript>4</Subscript>-EC polymer electrolytes

Li-ion rechargeable batteries based on polymer electrolytes are of great interest for solid state electrochemical devices nowadays. Many studies have been carried out to improve the ionic conductivity of polymer electrolytes, which include polymer blending, incorporating plasticizers and filler additives in the electrolyte systems. This paper describes the effects of incorporating nano-sized MnO₂ filler on the ionic conductivity enhancement of a plasticized polymer blend PMMA–PEO–LiClO₄–EC electrolyte system. The maximum conductivity achieved is within the range of 10⁻³ S cm⁻¹ by optimizing the composition of the polymers, salts, plasticizer, and filler. The temperature dependence of the polymer conductivity obeys the VTF relationship. DSC and XRD studies are carried out to clarify the complex formation between the polymers, salts, and plasticizer.     

Structural and ionic conductivity studies on proton conducting polymer electrolyte based on polyvinyl alcohol

An attempt has been made to prepare a new proton conducting polymer electrolyte based on polyvinyl alcohol (PVA) doped with NH₄NO₃ by solution casting technique. The complex formation between polymer and dissociated salt has been confirmed by X-ray diffraction analysis. The ionic conductivity of the prepared polymer electrolyte has been found by ac impedance spectroscopic analysis. The highest ionic conductivity has been found to be 7.5 × 10⁻³ Scm⁻¹ at ambient temperature for 20 mol% NH₄NO₃-doped PVA with low activation energy (~0.19 eV). The temperature-dependent conductivity of the polymer electrolyte follows an Arrhenius relationship, which shows hopping of ions in the polymer matrix.     

Transport properties of hexanoyl chitosan-based gel electrolyte

Films of hexanoyl chitosan-based polymer electrolyte were prepared by the technique of solution casting. The effect of plasticizer on the transport properties of hexanoyl chitosan:lithium trifluoromethanesulfonate (LiCF₃SO₃) electrolytes have been investigated. The plasticizer used was ethylene carbonate (EC). The highest room temperature conductivity achieved in the EC-plasticized hexanoyl chitosan-based electrolytes is 2.75×10⁻⁵ S cm⁻¹. The Rice and Roth model was used to explain the variations in the dc conductivity observed. The exponent, s, in Jonscher’s universal power law equation σ(ω)=σ _dc+Aω ^s , was analyzed as a function of temperature for the sample containing 30 wt% of EC. The analysis suggests that the conduction mechanism follows that proposed by the overlapping large polaron tunneling model.