坩埚旋转下降法生长硒镓银单晶体

本文报道了硒镓银多晶原料合成与单晶生长的新方法--熔体温度振荡法和坩埚旋转下降法.5～6N高纯Ag、Ga、Se单质按AgGaSe2化学配比富0.5;Se配料,1100℃下合成并在熔点附近进行温度振荡,获得了高纯单相致密的AgGaSe2多晶材料.用合成的多晶为原料,采用坩埚旋转下降法生长出φ22×80mm的AgGaSe2单晶锭.晶体外观完整,在10.6μm附近红外透过率达62.4;,吸收系数低于0.01cm-1,对10.6μm CO2激光实现倍频,能量转换效率达12;.     

双温区热扩散掺杂Fe2+∶ZnSe激光晶体的制备及激光输出性能

本文以CVD ZnSe晶片为基质材料,以FeSe粉末为掺杂物,采用双温区热扩散掺杂技术获得了尺寸为Ø22 mm×4 mm的Fe²⁺∶ZnSe激光晶体。通过二次离子质谱(SIMS)测试该晶体样品表面铁离子浓度为3.43×10¹⁸ cm^-3,并通过X射线光电子能谱(XPS)分析了晶体样品中铁元素的离子价态。采用UV/Vis/NIR分光光度计和傅里叶红外光谱仪测试了Fe²⁺∶ZnSe激光晶体的透过谱图。测试结果显示,在3.0 μm处出现了明显的Fe²⁺吸收峰,峰值透过率为5.5%。以波长为2.93 μm的Cr, Er∶YAG激光器为泵浦源,温度77 K时抽运尺寸10 mm×10 mm×4 mm的 Fe²⁺∶ZnSe晶体,获得了能量为191 mJ、中心波长4.04 μm的中红外激光输出,光光转换效率13.84%。     

红外非线性晶体材料AgGa1-xInxSe2的生长和性能表征

AgGa1-xInxSe2是近几年来研制的新型红外非线性光学晶体材料,其主要特点是借着Ga和In含量,即x值的变化,改变材料的折射率、双折射,实现三波共线非线性作用的非临界(90°)相位匹配.我们用垂直布里奇曼法生长单晶,获得了φ35mm×50mm的AgGa1-xInxSe2单晶棒.对生长出晶体棒In的浓度分布进行了测试.晶体元件用红外观察镜和分光光度计分别进行了观察和测试,晶体透光率良好.用一台TEA CO2激光泵浦一块5×6×16mm3的AgGa1-xInxSe2(x=0.3234)晶体元件,成功地实现了10.6μm非临界相位匹配倍频,输出5.3μm的中红外激光.     

坩锅下降法生长Nd3+∶LiYF4单晶及其光谱性能研究

以LiF∶ YF3∶NdF3=51.5∶47.5∶1为原料摩尔比,在50～60℃/cm固液界面温度梯度下,采用密封的坩埚下降法制备了尺寸为φ10 mm×50 mm的高质量Nd3+掺杂LiYF4单晶,并对产物的物相结构和光谱性能进行表征.结果表明,Nd3+在807 nm处的最大吸收系数α=1.96 cm-1,吸收跃迁截面为0.973 × 10-20 cm2.在808 nm LD激发下,测定了样品的荧光光谱和及最强荧光峰1050 nm(4F3/2→4I11/2)的荧光寿命(～451.0μs),并计算得到1050nm的最大受激发射跃迁截面为1.60×10-19 cm2.     

微乳液法制备不同形貌低维硒化锌纳米晶

利用微乳液法,实现了多晶硒化锌纳米空心球、单晶硒化锌纳米棒以及ZnSe量子点的低温合成.通过调整Triton X-100/环己烷/水体系中表面活性剂Triton X-100的浓度分别制备出直径在120 nm左右,壁厚在6nm左右的ZnSe多晶纳米空心球体、长度达1μm的单晶纳米棒和直径位于4～6nm的ZnSe量子点.紫外可见吸收光谱显示不同形貌ZnSe纳米结构的吸收特征具有较大的差别.     

CVT一步生长的ZnSe单晶的光电特性研究

本文采用化学气相输运(CVT)法,由Zn(5N)和Se(5N)一步直接生长了片状ZnSe单晶,并对其结构特性和光电性能进行分析。研究表明,生长出的ZnSe单晶仅显露(111)面,红外透过率约为40%～42%,具有较高的结晶质量。该ZnSe单晶可与In电极形成良好的欧姆接触,其体电阻率约为7.3×109Ω.cm。     

ZnSe和Cr∶ ZnSe单晶的温梯法制备及光学性能研究

采用温度梯度法(TGT)生长了直径为32 mm大尺寸ZnSe晶体.对生长出的ZnSe单晶进行了光学性能分析.采用磁控溅射方法在ZnSe晶体上镀铬膜,通过热扩散方法成功制备出中红外Cr∶ ZnSe激光晶体,并研究了Cr∶ZnSe晶体的光谱性能.吸收光谱测试观察到了Cr2+(3d4)取代四面体配位Zn2的5T2→5E能级的跃迁在1800nm的吸收带.77 K低温的光致发光光谱表明Cr∶ ZnSe晶体具有中心波长位于2.2 μm的宽谱带发射特征.     

Cr2+∶ZnSe中红外激光晶体生长及光谱性能

采用物理气相输运法( PVT),以Cr2+∶ ZnSe多晶为原料,在源区温度约为1000℃、温差为6～7℃条件下生长2周,获得了体积约为0.7 cm3的Cr2+∶ZnSe晶体.紫外-可见-近红外透过光谱显示,Cr2+∶ZnSe样品在1770nm左右出现了强吸收;Cr2+浓度在1019 atoms/cm3数量级,与原料中Cr2+浓度基本一致,反映了较低温度PVT法生长有利于获得预期的Cr2+掺杂浓度.荧光测试结果表明,Cr2+∶ZnSe样品谱线对称性好,发射峰位约在2400 nm,线宽约600 nm;室温荧光寿命为5.52×10-6s.数据分析结果表明,Cr2+∶ZnSe样品的吸收截面和发射截面峰值分别为1.1×10-18cm2和2.3×10-18 cm2.     

一种新型制备红外非线性晶体AgGaS_2的方法

采用改进的Bridgman法生长出25mm×70mm的AgGaS2单晶,并对样品进行了退火处理。通过X射线粉末衍射(XRD)测试,证实利用该方法制备的单晶确为AgGaS2;利用红外分光光度计检测,晶体0.5～12μm波段透过率在60%以上(未镀膜),表明晶体品质良好。另外,还加工出两块不同角度5mm×5mm×5mm倍频元件,在2.79μmEr,Cr∶YSGG和9.6μmCO2激光器上实现了倍频光输出。     

Fe2+∶ZnSe晶体制备及光学吸收

本文采用热扩散掺杂技术制备了Fe2+∶ZnSe晶体,获得尺寸达φ20 mm×2.0mm的晶体样品.光谱测试分析结果显示,晶体样品在3.0 μm附近具有显著的Fe2+∶ZnSe晶体的特征吸收,相对吸收强度达85;;通过ICP-AES测试该晶体样品中铁离子为4.5 ×1017 cm-3;分析了影响掺杂铁离子浓度的主要因素.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.