热激法光子晶体光纤光栅制备工艺中热传导特性研究

研究了基于结构性改变的光子晶体光纤光栅的热激法制备工艺,理论分析了此种工艺的成栅原理,采用热传导理论和有限元法研究了制备过程中光子晶体光纤中的温度场分布,以及包层空气孔结构和激光参数对成栅效果的影响.研究结果表明,利用光子晶体光纤包层空气孔周期性塌缩可以形成光栅;采用两点热激法时,能够实现能量在光纤径向均匀分布,轴向近似于高斯分布;包层气孔结构加速了成栅过程,相同光斑尺寸下,光纤塌缩所需激光功率随气孔层数和气孔半径的增大而减小;最后,对包层空气孔结构为1层到7层的光子晶体光纤热激过程进行仿真,得到了空气填 关键词： 光纤光栅 光子晶体光纤 热激法 有限元法     

偏振方向对阵列光束远场能量分布的影响

为了研究相干合成系统发光单元的偏振方向对相干合成远场光强分布的影响,以1维线性分布的阵列为例,利用傅里叶方法分析得到了单个发光单元的偏振方向偏离时相干合成的远场光强的解析表达式。数值计算结果表明:光源偏振方向的偏离使得远场中心光斑的峰值光强减小,光强的最小值不再为零,次瓣所包含的能量增大,但图样仍成对称性分布。对于5个单元合成系统,当单个发光单元偏振方向偏离π/2时,峰值光强减小到原来的68%左右。     

Er-doped fiber ring laser gyroscopes operating in continuous waves

A direction related polarizer was inserted into a ring laser cavity to eliminate one of the two eigen-modes as well as spatial hole burning of the gain medium in a bidirectional Er-doped fiber ring laser. Thus, a fiber ring laser gyroscope (FRLG) operating in continuous wave was demonstrated. A beat signal of over 30-dB noise was observed and a good inear relation between the beat frequency shift and cavity rotation rate was obtained.     

Fabrication of a quartz optical fiber tip for dental treatment with Nd:YAG laser—Proposal of a new process with TiO2 powder

In dental treatment with Nd:YAG laser beam, a quartz optical fiber is generally used to transmit the laser beam, which is irradiated to the hard and soft tissues for a caries treatment and a periodontal tissue excision. Since a normal optical fiber, which the laser beam comes out from the tip of the fiber, has difficulty irradiating to a narrow space and an inner root canal uniformly, it is effective to use a processed optical fiber tip from which is obtained a diffused and circumferential laser beam. In this paper, a new process to obtain these laser beams with TiO₂ powder is proposed, and the characteristics and the performances of the processed optical fiber were investigated. An experimental instrument was developed to measure the energy partition radiated from the processed fiber tip, and the ratio of a straight beam, a sideways beam and heat generated by the absorption of the laser beam was measured in each condition. As a result, the ratio of an energy partition was controllable by changing the incidence parameter to process the fiber tip, and the processed fiber tip corresponding to the clinical purpose could be obtained. The parameters which affected the processability of the fiber tip were processing time and incidence laser energy. The prepared cavity with processed fiber on the enamel was influenced by a straight beam, and the removal of enamel to the depth direction was controllable by using the processed fiber.     

量热式激光能量计内外表面温差对测量结果的影响

从理论上研究了量热式激光能量计激光照射过程中和激光照射后内外表面温度时间关系．编制了计算机程序计算得到激光照射时间内以及激光停止照射后内外表面温度关系曲线．通过稳定的高温温度场加热试验件模拟激光照射量热式激光能量计内外表面温度的升温过程，通过迅速将试验件移离高温温度场模拟激光停止照射后量热式能量计内外表面温度的变化，并测量了量热式能量内外表面温度时间曲线．实验和理论研究结果相符，结果表明激光停止照射后，内外表面温度迅速趋近，由此引入的测量不确定度小于0．25％．     

Effect of shot peening on the microstructure of laser hardened 17-4PH

In order to investigate the influence of shot peening on microstructure of laser hardened steel and clarify how much influence of initial microstructure induced by laser hardening treatment on final microstructure of laser hardened steel after shot peening treatment, measurements of retained austenite, measurements of microhardness and microstructural analysis were carried out on three typical areas including laser hardened area, transitional area and matrix area of laser hardened 17-4PH steel. The results showed that shot peening was an efficient cold working method to eliminate the retained austenite on the surface of laser hardened samples. The surface hardness increased dramatically when shot peening treatments were carried out. The analyses of microstructure of laser hardened 17-4PH after shot peening treatment were carried out in matrix area and laser hardened area via Voigt method. With the increasing peening intensity, the influence depth of shot peening on hardness and microstructure increased but the surface hardness and microstructure did not change when certain peening intensity was reached. Influence depth of shot peening on hardness was larger than influence depth of shot peening on microstructure due to the kinetic energy loss along the depth during shot peening treatment. From the microstructural result, it can be shown that the shot peening treatment can influence the domain size and microstrain of treated samples but laser hardening treatment can only influence the microstrain of treated samples.     

Formation of subwavelength periodic structures on tungsten induced by ultrashort laser pulses

The evolution of surface morphology of tungsten irradiated by single-beam femtosecond laser pulses is investigated. Ripplelike periodic structures have been observed. The period of these ripples does not show a simple relation to the wavelength and angle of incidence. The orientation of ripples is aligned perpendicularly to the direction of polarization for linearly polarized light. Surprisingly, we find that the alignment of the ripple structure turned left or right by 45 degrees with respect to the incident plane when using right and left circularly polarized light, respectively. The period of the ripple can be controlled by the pulse energy, the number of pulses, and the incident angle. We find a clear threshold for the formation as a function of pulse energy and number of pulses. The mechanism for the ripple formation is discussed, as well as potential applications in large-area structuring of metals.     

LD泵浦掺铥(Tm3+)光纤激光器的数值分析

首先从掺铥光纤激光器的速率方程和光传输方程出发,建立数学模型,通过Matlab软件进行数值计算,分析了泵浦光和激光沿光纤的分布以及各能级离子数的变化.在不同掺杂浓度下,研究了小信号增益与入纤泵浦功率的关系以及泵浦光和激光功率与增益介质长度的关系.在不同泵浦功率下,研究了输出功率与输出耦合镜反射率的关系.进一步对不同泵浦吸收系数,研究了斜率效率和泵浦阈值与光纤长度的关系.分析结果表明存在最佳光纤长度和最佳耦合输出透过率,使得激光输出功率达到最佳值.     

Laser field induced interband absorption in a strained GaAs/GaAlAs double quantum well system

Effect of laser field intensity on exciton binding energies is investigated in a GaAs/ GaAlAs double quantum well system. Calculations have been carried out with the variational technique within the single band effective mass approximations using a two parametric trial wave function. The interband emission energy as a function of well width is calculated in the influence of laser field. The laser field induced photoionization cross-section for the exciton placed at the centre of the quantum well is computed as a function of normalized photon energy. The dependence of the photoionization cross-section on photon energy is carried out for the excitons. The resulting spectra are brought out for light polarized along and perpendicular to the growth direction. The intense laser field dependence of interband absorption coefficient is investigated. The results show that the exciton binding energy, interband emission energy, the photoionization cross-section and the interband absorption coefficient depend strongly on the well width and the laser field intensity. Our results are compared with the other existing literature available.     

激光等离子体光谱测量影响因素分析

建立了一套激光等离子体光谱测量实验装置,以Nd:YAG调Q固体激光器(单脉冲平均能量38 mJ)为激发光源,铜合金为样品,得到了Cu原子辐射谱线随时间的变化情况,分析了系统中软、硬件因素对测量的谱线影响。实验证明激光器输出能量波动、每个数据点的平均次数、靶面相对于透镜焦点的位置、接受辐射的光纤束相对靶面法线的位置以及接受光纤束的有效通光口径都影响测量谱线的强度和重复精度。     

碳纤维复合材料的激光清洗等离子体光谱在线检测研究

近年来碳纤维复合材料（CFRP）由于性能优异,受到工业领域广泛关注。采用激光清洗技术预处理碳纤维复合材料表面的污染物和环氧树脂等杂质,有利于改善碳纤维复合材料表面性能,提高碳纤维复合材料胶接界面的结合强度。在线检测激光清洗过程,实时判断碳纤维复合材料的表面清洗质量,是保证激光清洗效果的关键环节,也是激光清洗装置自动化、集成化的核心技术。激光诱导等离子体光谱技术可以快速分析材料表面元素变化,实现在线检测激光清洗表面状态,在激光清洗领域有很广的应用前景。采用Nd∶YAG高能量脉冲激光器产生的1 064 nm激光在空气环境中诱导产生等离子体,利用改进型光栅光谱仪(ME5000)获取等离子体光谱,在线检测激光清洗碳纤维复合材料。研究外界空气环境对等离子体光谱检测结果的影响,发现350~700 nm波段的元素谱线可用于碳纤维复合材料表面物质成分分析;采用电子扫描显微镜观测的激光清洗表面形貌和X射线电子能谱仪测得的元素变化共同表征等离子体光谱检测的有效性,通过采集不同激光能量以及不同作用次数的等离子体光谱图,获得碳纤维复合材料表层树脂物质通过激光单次清洗干净的阈值,研究激光清洗质量与激光诱导等离子体谱线成分及其强度变化的关系。结果表明：在获取的激光诱导等离子体光谱中,光谱图中谱线波长在393.3 nm的S(Ⅱ)和589.5 nm的S(Ⅱ)谱线可有效在线表征碳纤维复合材料表面清洗质量;激光单次去除干净表面环氧树脂的阈值为10.68 mJ;低激光能量时需要清洗多次可以去除干净表面树脂;高激光能量时清洗单次可使表面树脂去除干净,多次清洗易造成基体损伤。实验结果为激光清洗碳纤维复合材料的智能集成化应用提供工艺依据和技术支持。     

Integrated optical Ti:Er:LiNbO3 distributed Bragg reflector laser with a fixed photorefractive grating

For the first time to the authors' knowledge, an integrated optical distributed Bragg reflector laser with a fixed photorefractive grating in LiNbO(3) is demonstrated. Sample preparation, grating fabrication, and laser characteristics are reported. The device is pumped by a fiber pigtailed laser diode (lambda(p) approximately 1480 nm) through the Bragg grating in a double-pass configuration, yielding an emission in the backward direction at lambda=1531.7nm . The laser threshold is 40 mW; as much as 5 mW of output power has been obtained at 110 mW of launched pump power in cw operation.     

光纤端面倾斜对光纤耦合高温计标定的影响

 分析了光纤端面倾斜对光能量耦合的影响和光纤接收角的变化。结果表明,光纤端面倾斜对光能量的耦合具有较大的影响,同时使光纤的接收角也产生较大的偏移。把这些结果与标定的具体情况相结合,提出了在高温计标定中应采取的措施,以提高系统的测量精度。     

2.5THz环烯烃聚合物中空芯光子晶体光纤设计与实验

采用全矢量有限元法,仿真设计了一种工作在2.5THz频段的中空芯太赫兹光子晶体光纤,用环烯烃聚合物材料(COC)制备了光纤样品,利用CO2激光泵浦气体太赫兹源搭建了测试平台并对光纤的太赫兹波传输性能进行了测试。实测光纤最低损耗0.17dB/cm、平均损耗约0.5dB/cm,在弯曲90°情况下光纤传输损耗波动小于5%,具有良好的可弯曲性;光纤输出端口的模场分布测试结果表明,光纤是以主模进行传输,太赫兹能量很好地被束缚在光纤芯中。     

316L不锈钢粉末光纤激光选区熔化特性

采用自行研制的光纤激光选区熔化快速成型设备,研究了选区激光熔化316L不锈钢粉末工艺参数、能量输入与样件致密度、表面形貌之间的关系以及微观组织特征。结果表明:扫描速度对成型效果影响最为显著;样件致密度随着激光能量密度提高有逐渐增大的趋势;能量密度作为选区激光熔化工艺的技术指标具有可操作性;表面形貌由激光功率与扫描速度比值所决定。深入探讨了能量输入、熔化凝固行为、激光功率与扫描速度比值与样件致密度、表面形貌的关系。结果表明:选区激光熔化凝固组织层内、层间熔合处为弧形,且为冶金结合,金相组织主要由柱状晶与等轴晶组成,层内靠近熔合线周围是柱状晶,而层间靠近熔合线附近主要是细小等轴晶,晶粒直径为1μm左右。     

Hydrodynamics of Plasma Interaction with an Intense Laser Field

A set of moment relations, which can describe the charged fluids response to an intense pump laser, and a linearization substitution relation, which is more appropriate as compared with the past treatment, are given by theoretical analyses. The relevant equations of state (adiabatic and isothermal), momentum and energy equations are derived self-consistently.The dispersion relations of the electron plasma wave and the ion acoustic wave driven by an intense pump laser field are-obtained. The results show that the frequencies of both the excited electron plasma wave and the excited ion acoustic wave have a great modification in the case of strong pump. The former bears out the theoretical result obtained from Vlasov equation and the later is consistent with experimental observations. It is proved that the zero-frequency component of the laser light wave contribution to the plasma pressure tensor is un-neglected,which implies a greatly change to the wave excitation properties, particularly in the direction of parallel or approximately parallel to the laser field vector.     

Active fiber composites for the generation of Lamb waves

Active fiber composites (AFC) are thin and conformable transducer elements with orthotropic material properties, since they are made of one layer of piezoelectric ceramic fibers. They are suitable for applications in structural health monitoring systems (SHM) with acoustic non-destructive testing methods (NDT). In the presented work the transfer behavior of an AFC as an emitter of transient elastic waves in plate-like structures is investigated. The wave field emitted by an AFC surface bonded on an isotropic plate was simulated with the finite-difference method. The model includes the piezoelectric element and the plate and allows the simulation of the elastic wave propagation. For comparison with the model experiments using a laser interferometer for non-contact measurements of particle velocities at different points around the AFC on the surface of the plate were performed. Transfer functions defined as the ratio of the electric voltage excitation signal and the resulting surface velocity at a specific point are separately determined for the two fundamental Lamb wave modes. In order to take the orthotropic behavior of the AFC into account the transfer functions are determined for several points around the AFC. Results show that the AFC is capable to excite the fundamental symmetric and antisymmetric Lamb wave mode. The antisymmetric mode is mainly radiated in the direction of the piezoelectric fibers, while the symmetric mode is spread over a larger angle. The amplitudes of the emitted waves depend on the frequency of the excitation as well as on the geometric dimensions of the transducer.     

Surface preparation of Ti–3Al–2.5V alloy tubes for welding using a fiber laser

Ti–3Al–2.5V tubes are widely used in aircraft hydraulic systems. Meticulous surface preparation before welding is necessary to obtain a sound weld involving these alloy tubes. Conventionally this is done by cleaning with environmentally malign toxic chemicals, such as, hydrofluoric acid and nitric acid. This paper describes the laser-cleaning process of the surface of these tubes with a fiber laser as a preparation for pulsed gas tungsten arc welding and results obtained. A simple one-dimensional heat equation has been solved to evaluate the temperature profile of the irradiated surface. It is shown that surface preparation by laser cleaning can be an environmentally friendly alternative process by producing acceptable welds with laser-processed tubes.     

Applied multi-pulsed laser in surface treatment and numerical-experimental analysis

This paper presents a comparison between simulation and experimental results of the melting process of metallic material by a pulsed laser source Nd-YAG. The simulations of temperature and velocity fields of melted material were done by solving the transient heat transfer and fluid-flow equations. Variations of the thermophysical properties were considered. Furthermore, the model included the effects of the surface-tension gradient on the fluid surface and the buoyancy force. The simulation was useful in improving our understanding of the phenomena occurring in the treated material. Using a laser triangulation sensor, an experimental study was also conducted on the surface profile of the melted zones to seek a relationship between the so-called keyhole effect and the laser triangulation measurements. The keyhole effect induced strong surface deformations and often formed cavities, which were undesirable in the surface treatment process. The laser power, energy density, and treatment duration could be optimized to prevent the keyhole effect. The predicted laser melted zone (LMZ) morphology was in good agreement with the corresponding experimental measurements for various irradiation conditions, as long as the keyhole effect did not occur.     

激光诱导金纳米棒图案化光纤SERS探针

研究了激光诱导沉积制备光纤表面增强拉曼散射(SERS)探针,并对探针的SERS性能进行检测。探讨光纤探针制备过程中金纳米棒溶液的浓度对探针灵敏度的影响。结果表明,将不同浓度的金纳米棒溶液进行激光诱导,在光纤端面会形成金纳米棒团簇和分散两种纳米结构。金纳米棒溶液的浓度、激光功率、诱导时间等因素都会对诱导沉积图案产生影响。实验利用功率为5 mW的激光进行诱导,在1.5×10^-9, 1.0×10^-9和7.5×10^-10 mol·L^-1的金纳米棒溶液中,经5 min沉积,制备出不同图案的光纤SERS探针。采用晶种法合成金纳米棒,用透射电子显微镜(TEM)观察金纳米棒形貌,并根据TEM图像分析计算了合成金纳米棒的长径比约为3.8。用扫描电子显微镜(SEM)观察金纳米棒的形貌以及激光诱导沉积后的纤维修饰端形貌,7.5×10^-10 mol·L^-1的金纳米棒溶液进行激光诱导,金纳米棒在光纤端面分布较为分散,而1.5×10^-9和1.0×10^-...