Low temperature preparation of flower-like BiOCl film and its photocatalytic activity

The BiOCl thin film with flower-like sphere structure was prepared at a low temperature by the alcoholysis-coating method using BiCl 3 as precursor. The obtained thin film was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), electronic energy spectrum (EDS) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS). And the results showed that the obtained BiOCl film without calcination was composed of flower-like sphere structure with tetragonal phase and had a good absorption for ultraviolet. The photocatalytic activity of BiOCl thin film was also evaluated by the degradation of methyl orange in water under UV light irradiation. The degradation experimental results confirmed that the film prepared at low temperature possessed a high photocatalytic activity and could achieve 97% degradation to 10 mg/L methyl orange solution after 150 min UV light irradiation. The stability of the obtained BiOCl thin film was also good and its photocatalytic activity still remained an above 94% removal of methyl orange after being used four times. In addition, a possible formation mechanism of BiOCl thin film was also inferred and the results suggested that the ethylene glycol solvent may contribute to the forming flower-like sphere structure.     

Photocatalytic decomposition of oil films floating on water using TiO_2 supported on hollow glass microbeads by sunlight

The feasibility of photocatalytic decomposition of oil films floating on water using TiO2 supported on hollow glass microbeads was studied.The results showed that 100% of ethylbenzene and 78% of dodecane can be photocatalytically removed after 8 h illumination with sunlight.The TiO2 supported on the hollow glass microbeads was not easily detached from the beads.After 150 h illumination there was no significant loss of the photocatalytic activity of TiO2 Some intermediate products of photocatalytic decomposition of dodecane were detected.     

铂沉积对Ga2O3-SiO2纳米粒子光催化性能的提高（英文）

Ga2O3‐SiO2 nanoparticles were prepared by a sol‐gel method and Pt was then immobilized on their surface via photo‐assisted deposition (PAD). The produced samples were characterized using X‐ray diffraction (XRD), ultraviolet and visible spectroscopy, photoluminescence emission spectroscopy, and surface area measurements. The catalytic performances of the Ga2O3‐SiO2 and Pt/ Ga2O3‐SiO2 samples were evaluated for the degradation of cyanide using visible light. XRD and EDX results showed that the Pt was well dispersed within the Ga2O3‐SiO2 phase and was detected on the surface of the catalyst, which confirmed the successful loading of Pt ions by the PAD method. BET results revealed that the surface area of Ga2O3‐SiO2 was higher than that of Pt/Ga2O3‐SiO2 . 0.3 wt% Pt/Ga2O3‐SiO2 exhibited the highest photocatalytic activity for degradation of cyanide under visible light. The catalyst could be reused with no loss in activity for the first 10 cycles.     

Characterization and photocatalytic properties of silver and silver chloride doped TiO2 hollow nanoparticles

Using polystyrene（PSt） particles as template,PSt/TiO₂ composite particles with AgCl incorporation were prepared through hydrolysis of tetrabutyl titanate in the presence of AgNO₃ and NaCl.AgCl doped TiO₂ hollow particles were successfully prepared with the PSt/TiO₂ composite microspheres pretreated at 180℃followed by calcination.The morphology of PSt/TiO₂ particles and the crystal structures of the AgCl doped TiO₂ hollow particles were characterized.The photocatalytic activity of the doped TiO₂ hollow particles in degradation of Rhodamine B was tested under UV and visible lights and compared to that with Ag doped TiO₂ particles.The results showed that TiO₂ hollow particles,either doped with Ag or AgCl,demonstrated higher photocatalytic activity than the pure TiO₂ particles.This enhancement in photocatalytic activity was more significant with AgCl doped TiO₂ than that with Ag doped,and more distinct when the degradation was done under visible light than that under LTV light.     

Effect of Doped Boron on the Properties of ZnO Thin Films Prepared by Sol-gel Spin Coating

Transparent conductive boron-doped ZnO thin films were prepared by sol-gel spin coating method. The effect of doped boron concentration on the properties of the films was systematically discussed. The films were characterized by X-ray diffraction, atomic force microscopy, spectrophotometry, and Hall effect measurement system. All the doped and undoped ZnO films were of a single hexagonal structure, and showed a preferred orientation of （002）. The particle size and surface roughness of the films decreased with increased doped boron concentration. All the films exhibited an average transmittance of approximate 90% in visible-light region and an energy gap of about 3.3 cV. The maximum carrier concentration, the highest carrier mobility and the lowest resistivity were observed at a doped boron concentration of 0.5%（molar fraction）. Based on these results, we suggested that the saturation concentration of doped boron in ZnO film is 0.5%（molar fraction）.     

Double layered, one-pot hydrothermal synthesis of M-TiO2 (M = Fe3+, Ni2+, Cu2+ and Co2+) and their application in photocatalysis

A double layered,one-pot hydrothermal method was adopted in this work to prepare transition metal ions(Fe3+,Ni2+,Cu2+and Co2+)doped TiO2.The morphology and chemical properties of TiO2and the status of metal ions were characterized with XRD,TEM,BET,UV-Vis and XPS analysis.TEM images show that the obtained TiO2was very uniform with an average particle size of 10.4 nm.XPS,TEM and XRD results show that transitional metals were doped onto TiO2in the form of ions.Photocatalytic decomposition of oxalic acid under UV illumination and methylene blue degradation under visible light on these materials were conducted,respectively.The results reveal that Cu2+-TiO2and Co2+-TiO2showed a highest activity under UV and visible light illumination,respectively,and they were both more active than commercial P25 TiO2.With this special design of double layers,the hydrolysis of titanium precursor in the system with water can be easily controlled and metal ions are simply doped.This strategy can be further applied to synthesize metal ion doped TiO2using various metal precursors with controllable amounts,and thus lead to better optimization of highly active photocatalyst.     

Gas-phase photocatalytic oxidation of benzene over titanium dioxide loaded on Bi_(12)TiO_(20)

TiO2 was prepared by sol-gel method using tetrabutyl titanate as precursor. TiO2 was loaded on Bi12TiO20. The photocatalyst with different TiO2 loading was calcined at 723 K. The photocatalytic activity of decomposition gaseous benzene was investigated in a batch reactor. The prepared photocatalyst was characterized by UV-vis diffuse reflectance. The result showed that TiO2/Bi12TiO20 absorbed much more ultraviolet light than Ti02 in the ultraviolet light region and showed red shift. The results indicated that the prepared photocatalyst can greatly promote the photocatalytic activity. The 2.0% TiO2/Bi12TiO20 system exhibited the highest photocatalytic activity.     

Properties of TiO2-SiO2 Mixed Oxides and Photocatalytic Oxidation of Heptane and Sulfur Dioxide

A series of TiO2-XSiO2[X denotes the molar fraction(%) of silica in the mixed oxides] with different n(Ti)/n(Si) ratios was prepared with ammonia water as a hydrolysis catalyst. The photocatalysts prepared were characterized by XRD, thermal analysis, FTIR, UV-Vis and SPS. The characterization results of FTIR and UV-Vis spectra show that Ti atoms were gradually changed from octahedral coordination to tetrahedral coordination with the addition of silica, which is not beneficial for obtaining strong Bronsted acidity and higher photocatalytic activity. The photocatalytic activity experiments, which were conducted by using heptane (or SO2) as the model reactant, showed that TiO2-SiO2 containing a suitable amount of silica can exhibit much higher photocataiytic activity than pure TiO2. The enhanced photocatalytic activity can be attributed tothree following factors.. (1) smaller crystalline size;(2) higher thermal stability; (3) the new strong Broensted acidity.     

Preparation of Nano-crystalline Tungsten Carbide Thin Film by Magnetron Sputtering and Their Electrocatalytic Property for PNP Reduction

Nano-crystalline tungsten carbide thin films were deposited on Ni substrates by magnetron sputtering using WC as target material. The crystal structure and morphology of the thin films were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM） Electrochemical investigations showed that the electrode of the thin film exhibited higher electrocatalytic activity in the reaction of p-nitrophenol （PNP） reduction. FT-IR analysis indicated that p-aminophenol （PAP） was synthesized after two step reduction of PNP on nano-crystalline tungsten carbide thin film electrode.     

Microwave‐Hydrothermal Preparation and Visible‐Light Photoactivity of Plasmonic Photocatalyst Ag‐TiO2 Nanocomposite Hollow Spheres

Visible‐light‐driven plasmonic photocatalyst Ag‐TiO₂ nanocomposite hollow spheres are prepared by a template‐free chemically‐induced self‐transformation strategy under microwave‐hydrothermal conditions, followed by a photochemical reduction process under xenon lamp irradiation. The prepared samples are characterized by using scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, N₂ adsorption‐desorption isotherms, X‐ray photoelectron spectroscopy, UV/Vis and Raman spectroscopy. Production of ?OH radicals on the surface of visible‐light illuminated TiO₂ was detected by using a photoluminescence method with terephthalic acid as the probe molecule. The photocatalytic activity of as‐prepared samples was evaluated by photocatalytic decolorization of Rhodamine B (RhB) aqueous solution at ambient temperature under visible‐light irradiation. The results show that the surface plasmon absorption band of the silver nanoparticles supported on the TiO₂ hollow spheres was red shifted, and a strong surface enhanced Raman scattering effect for the Ag‐TiO₂ nanocomposite sample was observed. The prepared nanocomposite hollow spheres exhibits a highly visible‐light photocatalytic activity for photocatalytic degradation of RhB in water, and their photocatalytic activity is higher than that of pure TiO₂ and commercial Degussa P25 (P25) powders. Especially, the as‐prepared Ag‐TiO₂ nanocomposite hollow spheres at the nominal atomic ratio of silver to titanium ( R ) of 2 showed the highest photocatalytic activity, which exceeds that of P25 by a factor of more than 2.     

载钛羟基磷灰石光催化降解内分泌干扰物双酚A

对载钛羟基磷灰石（TiHAP）进行了透射电镜、X射线衍射、紫外-可见光谱和Zeta电位表征,并应用液相色谱-质谱技术对比了TiHAP和P25 TiO₂对环境内分泌干扰物双酚A（BPA）的吸附和光催化降解性能,探讨了富里酸和Fe³⁺对TiHAP薄膜光催化性能的影响。结果表明,TiHAP和TiO₂粉体对BPA的吸附符合Langmuir吸附等温方程,且前者吸附性能更大。TiHAP薄膜光催化降解BPA的性能优于TiO₂薄膜;富里酸和Fe³⁺对TiHAP和TiO₂薄膜光催化性能的影响趋势不同,从能带结构、电子转移和吸光性等角度分析了性能不同的原因。本结果可以为应用TiHAP降解环境内分泌干扰物提供依据。     

Building surface defects by doping with transition metal on ultrafine TiO2 to enhance the photocatalytic H2 production activity

Inefficient charge separation and limited light absorption are two critical issues associated with high-efficiency photocatalytic H₂ production using TiO₂. Surface defects within a certain concentration range in photocatalyst materials are beneficial for photocatalytic activity. In this study, surface defects (oxygen vacancies and metal cation replacement defects) were induced with a facile and effective approach by surface doping with low-cost transition metals (Co, Ni, Cu, and Mn) on ultrafine TiO₂. The obtained surface-defective TiO₂ exhibited a 3–4-fold improved activity compared to that of the original ultrafine TiO_2. In addition, a H₂ production rate of 3.4 μmol/h was obtained using visible light (λ > 420 nm) irradiation. The apparent quantum yield (AQY) at 365 nm reached 36.9% over TiO₂-Cu, significantly more than the commercial P25 TiO₂. The enhancement of photocatalytic H₂ production activity can be attributed to improved rapid charge separation efficiency and expanded light absorption window. This hydrothermal treatment with transition metal was proven to be a very facile and effective method for obtaining surface defects.     

Cu/Ni助催化剂对TiO2光催化制取苯酚性能的影响

以TiO₂纳米粒子为主催化剂, 采用“浸渍-还原法”构筑了铜、镍共负载的二氧化钛基光催化系统。以苯为起始原料, H₂O₂为氧化剂, 研究了Cu/Ni助催化剂对TiO₂可见光催化制取苯酚性能的影响并对Cu/Ni助催化剂的作用机制进行了探讨。结果表明, 在可见光照射下, 纯TiO₂纳米粒子对苯氧化制取苯酚反应没有催化活性。铜、镍的引入可以明显地增强TiO₂可见光催化制取苯酚的活性。当使用负载有铜、镍的TiO₂作为催化剂时, 苯酚的产率可达到18%。结果还表明Cu、Ni之间存在着很强的协同作用。在该协同作用下, Cu、Ni共负载的TiO₂纳米粒子表现出了较单一金属负载的TiO₂纳米粒子高得多的光催化活性。     

Cu/Ni助催化剂对TiO2光催化制取苯酚性能的影响

以TiO₂纳米粒子为主催化剂,采用"浸渍-还原法"构筑了铜、镍共负载的二氧化钛基光催化系统。以苯为起始原料,H₂O₂为氧化剂,研究了Cu/Ni助催化剂对TiO₂可见光催化制取苯酚性能的影响并对Cu/Ni助催化剂的作用机制进行了探讨。结果表明,在可见光照射下,纯TiO₂纳米粒子对苯氧化制取苯酚反应没有催化活性。铜、镍的引入可以明显地增强Ti₀₂可见光催化制取苯酚的活性。当使用负载有铜、镍的TiO₂作为催化剂时,苯酚的产率可达到18%。结果还表明Cu、Ni之间存在着很强的协同作用。在该协同作用下,Cu、Ni共负载的TiO₂纳米粒子表现出了较单一金属负载的TiO₂纳米粒子高得多的光催化活性。     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

Synthesis of Fe<Superscript>3+</Superscript> doped ordered mesoporous TiO<Subscript>2</Subscript> with enhanced visible light photocatalytic activity and highly crystallized anatase wall

Fe³⁺ doped mesoporous TiO₂ with ordered mesoporous structure were successfully prepared by the solvent evaporation-induced self-assembly process using P123 as soft template. The properties and structure of Fe³⁺ doped mesoporous TiO₂ were characterized by means of XRD, EPR, BET, TEM, and UV–vis absorption spectra. The characteristic results clearly show that the amount of Fe³⁺ dopant affects the mesoporous structure as well as the visible light absorption of the catalysts. The photocatalytic activity of the prepared mesoporous TiO₂ was evaluated from an analysis of the photodegradation of methyl orange under visible light irradiation. The results indicate that the sample of 0.50%Fe–MTiO₂ exhibits the highest visible light photocatalytic activity compared with other catalysts.     

Samarium-doped mesoporous TiO2 nanoparticles with improved photocatalytic performance for elimination of gaseous organic pollutants

Mesoporous TiO₂ doped with different amounts of Sm were prepared via a sol-gel route with Pluronic P123 as template. The materials were characterized by X-ray diffraction, transmission electron microscopy, and N₂ sorption experiments, etc. The photocatalytic activity of the mesoporous TiO₂ was tested in elimination of gaseous methanol and acetone. The Sm doped mesoporous TiO₂ have higher activity than those of the commercial photocatalyst (Degussa, P25) and Sm doped TiO₂ counterparts without mesopore structure under ultraviolet light irradiation. A possible mechanism was proposed to account for the high photocatalytic activity of the Sm doped mesoporous TiO₂. The superior activity of the Sm doped mesoporous TiO₂ may be attributed to the synergic effect of the high surface area, mesopore structure and doped Sm species.     

Visible-light-sensitive N-doped TiO<Subscript>2</Subscript> photocatalysts prepared by a mechanochemical method: effect of a nitrogen source

Nitrogen-doped titanium dioxide (N-doped TiO₂) photocatalysts were prepared by a mechanochemical method by using a high-speed ball milling of P25 TiO₂ with nitrogen sources such as ammonia solution, hexamine, and urea. Visible-light absorption was determined from the onset of diffused reflectance spectrum. The photocatalytic activity of the N-doped TiO₂ was evaluated through the removal of methylene blue (MB) under visible-light irradiation. The effects of nitrogen precursors used during the mechanochemical synthesis on the catalysts’ properties, such as the effective particle size, surface area, and photocatalytic activity, were extensively investigated.     

有机改性TiO2光催化剂的制备及可见光催化性能

以染料黄叱精(Chrysoidine G)和TiO₂ (Degussa P25)为原料, 利用甲苯二异氰酸酯为桥连体, 成功合成了一种有机改性的TiO₂光催化剂. 采用XRD, TEM, FT-IR, UV-Vis对所得催化剂进行了表征, 以亚甲基蓝降解为探针反应, 考察其可见光催化性能. 结果表明: 甲苯二异氰酸酯在黄叱精和TiO₂之间形成了稳定的化学键, 从而实现了对TiO₂的表面有机改性; 改性后的TiO₂在可见光区(400～550 nm)有明显的吸收; 与未改性TiO₂相比, 有机改性的TiO₂催化剂在可见光照射下表现出了很好的光催化性能.