升级的合肥光源闭轨测量系统及其应用

 描述了合肥同步辐射光源二期工程中，电子储存环升级的闭轨测量系统及其在设备研制中的应用。介绍了性能稳定可靠的Bergoz束流位置监测电子学信号处理器。升级后的闭轨测量系统中处理电子学电路的束流位置分辨率可达1μm，系统误差小于10μm。整个测试系统的分辨率小于3μm。利用该高精度闭轨测量系统和基于束流准直系统完成了束流准直四极铁磁中心的测量，并和控制系统完成了储存环全环闭轨反馈校正试验。一个完整的束流位置监测系统已投入了在线运行，保障了为用户提供高稳定高品质的光源。     

BEPC II直线加速器数字BPM前端调理电路的研制

针对北京正负电子对撞机改造工程（BEPC II）直线加速器束流位置测量电子学系统故障率上升这一现状,结合BEPC II直线加速器束流参数以及BPM电子学ADC芯片带通采样的需求,设计了隔离度高、幅相一致性好的数字BPM射频前端电子学模块。数字BPM电子学系统采用MicroTCA 4.0系统架构,以FPGA作为主控制器,基于EDA软件开发设计。重点介绍了射频前端电子学模块中射频功率放大器、数字可调衰减器、带通滤波器等设计和实验室及在线测试结果。BEPC II对撞模式下,使用正电子束流,完成电子学系统在线测试,x方向位置测量精度约为38.46 μm,y方向位置测量精度约为26.16 μm,其测量精度和系统稳定性优于商用模拟BPM电子学模块,能够满足BEPC II直线加速器束流位置测量需求。     

基于导频技术的数字束流位置测量系统的研制

为改善传统的束流位置测量电子学系统受电子学通道非线性、温度漂移和系统噪声等因素对位置测量精度带来的影响,介绍了一种新型的基于导频技术的数字束流位置测量电子学系统。该系统硬件包括模拟信号采集电子学、数字信号处理电子学和PTC(导频信号耦合)模块;软件包括顶层应用软件和底层驱动,束流信号与导频信号在耦合电路中耦合后,经电子学处理,在FPGA中计算得到归一化后的束流位置信息。实验室测试结果分析,经导频信号归一化处理后能够有效改善各通道随温度变化的现象,束流位置漂移从4.5 μm改善至0.5 μm,分辨率从57.25 nm提升到13.37 nm,并且进行导频信号开关实验更加直观观测导频信号对束流位置测量的在线校正效果。设计的基于导频信号的数字束流位置测量（DBPM）电子学可以高效、实时地实现对加速器束流位置的在线校正,提升电子学系统的实时分辨率性能。     

合肥光源逐圈测量系统试验结果及其在注入调试中的应用

 介绍了合肥光源(HLS)逐圈束流位置测量系统在升级后的注入系统联调中的作用。该逐圈测量系统信号处理器采用对数比电路，数据获取采用NI5102 ADC。为了保证长达2s数据获取，采样数据通过突发的DMA方式实时写入工控机的系统内存。注入Kicker用作为激励束流，以便监测衰减率和研究β振荡。     

合肥光源直线加速器BPM系统的研制和测量

合肥光源直线加速器新改造的BPM系统已经安装, 并做了在线的束流位置测量实验. 本文介绍该BPM系统的结构、作为系统核心部分的信号处理模块以及离线标定的实验结果和在线应用的实验结果, 表明该BPM系统具有不小于40dBm的动态范围, 不大于100μm的束流位置分辨率, 水平方向和垂直方向分别具有1.61dB/mm和1.51dB/mm的灵敏度. 校正铁强度与BPM读数关系的实验, 表明该BPM系统能正确地反映束流的位置变化情况, 并且确定了校正铁在水平方向和垂直方向的校正系数分别为0.46mm/A和0.58mm/A, 校正铁设置为默认值时该BPM处的束流中心水平位置和垂直位置分别为0.83mm和－0.57mm.     

HLS注入段束流位置探头定标电场的拟合和误差计算

 描述了束流位置探测器(BPM)探头定标、定标电场的拟合和误差计算。该定标系统采用了具有调节精度为10μm垂直放置真空管道的天线模拟定标装置和分辨率高达1μm外差式、窄带频域信号处理电子学线路。并推导出针对合肥光源（HLS）定标系统条件下的电场拟合函数及相关的BPM-Mapping图和误差计算结果,较精确地计算出该高精度定标系统误差。     

同步辐射小角散射实验站

小角X射线散射(SAXS)实验站配置有SAXS相机、在线控制及数据获取系统.SAXS相机由位置精度为1μm的狭缝系统、用以监测光强的电离室、在垂直于束流的平面内能作水平和垂直两个方向遥控调节的样品台和可调长度低真空管道等部分组成,真空管道的两端有25μm厚的Kapton膜密封,探测器为闪烁计数器.该装置的角分辨优于0.6mrad.     

改进后的BEPC储存环束流位置测量系统

介绍改进后的北京正负电子对撞机束流位置测量系统的软硬件结构和系统的性能.改进后系统的位置测量重复性优于10μm,测量一次闭轨的时间为11s,系统的动态范围大于81dB,最小可测束流强度低于0.5mA,测量结果的可信度是通过自洽检测来保证的.     

数字束流位置信号处理算法优化

在已有束流位置信号下变频算法的设计与实现的基础上,优化了算法时序,设计实现了数字自动增益控制、慢应用信号处理等模块功能,能获得逐圈、快应用及闭轨数据。上海光源储存环上的束流测试结果显示,处理器可正确获取包含束流真实运动的多速率位置数据。在174 mA储存环流强、500个束团的填充模式时,逐圈位置数据分辨力达到0.84 m,快应用位置数据分辨力达到0.44 m,闭轨位置数据分辨力达到0.23 m,性能满足设计要求。     

中国散裂中子源反角白光中子源T0信号的精确扇出方法

反角白光中子源位于中国散裂中子源(CSNS),是以不同中子能量下的核数据测量为目标的大型物理实验装置,中子的能量是通过中子飞行时间(TOF)来获取的.实验中,将质子束流轰击钨靶的时刻作为TOF的起始时刻(T0),相应的电子学信号被用于触发整个电子学系统的运行.为了保证TOF测量的准确性和电子学系统各通道采集的同步性,需...     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.