Sub-ambient temperature effects on the separation of monosaccharides by high-performance anion-exchange chromatography with pulse amperometric detection: Application to marine chemistry

The effects of column temperature in the range 10–45°C using high-performance anion-exchange chromatography (HPAEC) and pulse amperometric detection are described for the determination of monosaccharides. The influence of temperature was tested with an isocratic elution of NaOH at concentrations varying from 2.5 to 20 mM and with a post-column addition of 1 M NaOH. The results showed that small changes of temperature greatly affect retention times and resolution (R_s) of monosaccharides and particularly those of the both pairs xylose–mannose and rhamnose–arabinose which cannot be simultaneously detected at usual room temperature (25°C). Our results suggest that a subambient temperature of 17°C and an eluent concentration of 19 mM are the more appropriate conditions for an acceptable separation (R_s rha/ara=1.02, R_s man/xyl=0.70) in a short analytical run time (35 min). The results showed that within the range of temperatures studied, enthalpy and entropy are invariant of temperature indicating that changes in the retention processes are mainly due to temperature than other associated changes in the system. This study demonstrated the importance of controlling temperature during HPAEC of monosaccharides, both to accomplish highly reproducible retention times and to achieve optimal separation of sugars. This method gave acceptable results for detection of marine sugars.     

Retention behavior of alkali, alkaline earth and transition metal cations in ion chromatography with an unmodified silica gel column

An unmodified silica gel (Develosil 30-5) column (150×4.6 mm I.D.) has been applied to the ion chromatographic separation of alkali, alkaline earth and transition metal cations. The retention behavior of the above cations on the bare substrate was investigated using a number of weak inorganic and organic acid eluents. During this investigation, several separations were achieved and the most suitable eluent conditions were identified. It was concluded that: (a) 1.5 mM HNO₃-0.5mM pyridine-2,6-dicar☐ylic acid eluent was the most effective for the simultaneous separation of common alkali and alkaline earth metal cations, (b) 1.5 mM oxalic acid eluent resulted in the best separation of alkali, alkaline earth, and transition metal cations, (c) 0.5 mM CuSO₄ eluent could be used for the separation of alkali metal cations alone and (d) 0.5 mM ethylenediamine-oxalic acid eluent at pH 5.5 resulted in themost efficient separation of both alkaline earth and transition metal cations.     

Ion chromatography of nitrite and carbonate in inorganic matrices on an octadecyl—poly(vinyl alcohol) gel column using acidic eluents

Low levels of carbonate and nitrite contained in inorganic matrices were determined by ion chromatography on an Asahipak ODP-50 poly(vinyl alcohol) gel-based reversed-phase column. With an acidic mobile phase, inorganic matrix anions and cations eluted near the void volume of the column, whereas carbonate and nitrite were retained and separated completely from the matrix ions. After the separation column, the peak response was enhanced using a cation-exchange hollow fibre and 25 mM sodium sulphate or alkaline enhancers. Sea-water samples can be applied directly for the determination of carbonate and added nitrite at ppm levels. The maximum sample volume that can be loaded on the column without peak deformation depended on the pH of the sample solution and the sulphuric acid concentration in the eluent. A 50 μl sea-water sample was applicable with a 2.5 mM acid eluent.     

Multivariate optimisation of a cyclodextrin-assisted-capillary zone electrophoretic method for the separation of torasemide and its metabolites

In this work, a rapid cyclodextrin-assisted capillary electrophoretic method is developed for the separation of the diuretic torasemide and three of its metabolites. Both fractional factorial and central composite designs were employed to optimise the separation method. The factors studied were pH, concentration of methyl-β-cyclodextrin, concentration of the background electrolyte and percentage of acetonitrile as organic modifier. Monitored response was a composite quality response (Q*) which balanced conflicting normalized responses, such as resolution and migration time. Optimal separation of the four studied compounds was achieved in less than 6.5 min, using an electrolyte of 60 mM borate buffer with no organic modifier and 25 mM methyl-β-cyclodextrin concentration adjusted to pH 8.0 at a potential of 30 kV. Detection wavelength and temperature were 197 nm and 20 °C respectively. This work means a significant improvement with regard to a previous separation method for these compounds developed in our laboratory.     

On the thermodynamic equilibrium between ice and electrolyte solutions in the conditions of confined geometry

For a small volume (of about 10⁻⁶ cm³) of NaCl and other electrolyte solutions (C = 0.1 and 1 M) in thin (r = 5/10 μm) single quartz capillaries, dependencies of the column length l of frozen solutions on the temperature t were measured using comparator IZA-2 in a thermostated chamber. At temperatures range t > −4 °C (for C = 0.1 M) and t > −8 °C (for C = 1 M) the l(t) dependencies are reversible and therefore correspond to establishment of an equilibrium between ice-1 and the solution.

From the constants mass condition of the dissolved salt in a frozen column, the l(t) expression was derived, which includes thermodynamic relation between solution concentration in an equilibrium with ice, C_s, and the temperature t for bulk systems. Deviations from the data known for bulk solutions were observed in thin capillaries when temperature t decreased to −3 °C (for 0.1 M NaCl) and to −6 °C for 1 M NaCl solution.

This effect may be a result of strong adhesion of the ice column to capillary walls. In this case, some internal stresses arise in frozen solution resulting in a deviation from thermodynamic equilibrium conditions for bulk systems. When approaching the temperature of ice melting, adhesion forces decrease due to formation of a thin non-freezing water interlayer on the capillary wall. In this temperature range the experimental data are in agreement with the predictions for bulk systems. It was supposed that the observed deviation in thin capillaries may be caused by formation of an amorphous ice phase with higher density as compared with the ice-1 during rapid freezing, or by an effect of ice microlenses formation. Both effects will result in a deviation from the phase diagram corresponding to a bulk solution.     

Determination of bioactive diterpenoids from Andrographis paniculata by micellar electrokinetic chromatography.

The present paper describes the development of a micellar electrokinetic chromatographic (MEKC) method for simultaneous determination of andrographolide, deoxyandrographolide and neoandrographolide in ethanol extracts of Andrographis paniculata. Separations were carried out in a fused-silica capillary tube with UV detection at 214 nm. Good separation was achieved using a 20 mM borate buffer, containing 20 mM sodium dodecyl sulphate and 10 mM sodium cholate, adjusted to pH 8.3 at an operating voltage of 25 kV, temperature of 35°C and a hydrodynamic injection of 5 s. The method was validated with good correlation coefficients obtained (0.9986–0.9989) while relative standard deviation (RSD) of migration time was between 1.14 and 2.42. It is concluded that this method could be used for speedy and accurate qualitative and quantitative analysis of bioactive diterpenoids in andrographis herb and its derived products.     

Capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples from hydrothermal springs and fumaroles

A new application of capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples is presented. Ten fluid samples were collected from hydrothermal springs and fumaroles located in a volcanic zone of Deception Island, Antarctica. Anion separation was achieved in less than 6 min using indirect UV detection at 254 nm with a negative power supply (−15 kV). The electrolyte consisted of 4.7 mM sodium chromate, 4.0 mM electroosmotic flow modifier (OFM) hydroxide, 10 mM 2-(N-cyclohexylamino)ethanesulfonic acid and 0.1 mM calcium gluconate (pH 9.1). Major anions (Cl⁻, SO₄², PO₄H²⁻, and CO₃H⁻) were measured using hydrostatic injection (10 cm for 30 s) at 25°C. Trace amounts of anions (F⁻, Br⁻, and NO₃⁻) were better determined by electromigration injection (4 kV, 10 s) at 15°C. Good reproducibility of the migration times (<0.72% RSD), a satisfactory linear response and accuracy as well as acceptable detection limits were successfully obtained.     

Sheath liquid effects in capillary high-performance liquid chromatography-electrospray mass spectrometry of oligonucleotides

Fused-silica capillary columns of 200 μm inner diameter were packed with micropellicular, octadecylated, 2.3 μm poly(styrene–divinylbenzene) particles and applied to the separation of oligonucleotides by ion-pair reversed-phase high-performance liquid chromatography. Oligonucleotides were eluted at 50°C with gradients of 3–13% acetonitrile in 50 mM triethylammonium bicarbonate. Addition of sheath liquid to the column effluent allowed the detection of oligonucleotides by electrospray ionization mass spectrometry using full-scan data acquisition with a detectability comparable to that obtained with UV detection. The signal-to-noise ratios with different sheath liquids increased in the order isopropanol相似文献   

High-performance liquid chromatography with amperometric detection applied to the screening of 1,4-dihydropyridines in human plasma

A high-performance liquid chromatographic method with electrochemical detection has been developed for the determination of six 1,4-dihydropyridines: nifedipine, nimodipine, nisoldipine, nicardipine, felodipine and lacidipine. The chromatographic separation was performed using a Supelcosil LC-ABZ+Plus C₁₈ column. A mobile phase of methanol–water (70:30), containing 2 mM CH₃COOH–CH₃COONa at a flow-rate of 1 ml/min and a pH of 5.0, was used. The temperature was optimized at 30±0.2°C. The amperometric detector, equipped with a glassy carbon electrode, was operated at 1000 mV versus Ag/AgCl in the direct current mode. The method was applied to the determination of these compounds at ng/ml concentrations, obtaining intra-day reproducibilities of lower than 5.0% in terms of relative standard deviations and detection limits ranging from 16 to 44 ng/ml. The method was applied to the screening of 1,4-dihydropyridines in spiked plasma samples, with a total elution time of lower than 18 min, obtaining the best recoveries for nimodipine and felodipine (91 and 88%, respectively). These recoveries together with the low detection limits achieved allow its application to the analysis of these drugs in human plasma.     

Measurement of glass transition temperature by mechanical (DMTA), thermal (DSC and MDSC), water diffusion and density methods: A comparison study

Glass transition measured by DMTA from the change in slope in storage modulus was 55 °C, which was 10.5 °C lower than the value measured by tan δ peak. Initial glass transition measured by DSC, increased exponentially and reached a constant value of 55 °C at or higher heating rate of 30 °C/min. Transition temperature, measured by MDSC, remained constant up to heating rate 15 °C/min and then decreased. The glass transition values determined from reversible heat flow was 60 °C. The break in diffusivity and density (i.e. volume) was observed at 50 °C below the glass transition temperature measured by thermal and mechanical methods.     

Development and validation of a capillary zone electrophoresis method for the quantitative determination of anthocyanins in wine

A capillary zone electrophoresis (CZE) method is proposed for the quantitative determination of anthocyanins in wine as an alternative to high-performance liquid chromatography. The CZE separation was carried out using a 46 cm (effective length)×75 μm I.D. fused-silica capillary at 10 °C and a 50 mM sodium tetraborate buffer at pH 8.4 with 15% of methanol as modifier. A voltage of 25 kV and a hydrodynamic injection of 300 mbar s were used. The electropherograms were recorded at 599 nm. It was found that SO₂ (antibacterial and antioxidant agent added to wine during its production) increased the absorbance of anthocyanins at 599 nm in a basic medium. Therefore, a concentration of 250 mg/l of SO₂ was added to the samples and the calibration solution before the analysis in order to avoid errors by this matrix effect. The analytical response was linear (R=0.998) between 10 and 700 μg/ml of malvidin-3-O-glucoside. The limit of detection and the reproducibility (as a relative standard deviation, n=11) were 1 μg/ml and 1.5%, respectively. Finally, the CZE method was validated by the analysis of synthetic wine samples (errors less than 8%) and by the comparison of the results obtained in the analysis of different monovarietal wines by CZE with those obtained by the standard HPLC method. In this comparison, a good correlation (R=0.998) with a slope of 1.005±0.044 and an intercept of −0.752±6.690 was obtained for malvidin-3-O-glucoside.     

Freezing of water bound in lichen thallus as observed by H NMR. II. Freezing protection mechanisms in a cosmopolitan lichen Cladonia mitis and in Antarctic lichen species at different hydration levels

Proton NMR spectra at 300 MHz for dehydrated and hydrated thallus of Cladonia mitis Sandst. [=C. arbuscula (Wallr.) Flot ssp. Mitis (Sandst.) Ruoss], Himantormia lugubris (Hue) Lamb and Usnea aurantiaco-atra (Jacq.) Bory were recorded. The temperature was decreased from room temperature down to −45 °C. Pulse length was set to π/2=8.3 μs, which allowed the observation of tightly bound and loosely bound/or free water fraction, whereas the signal from solid matrix of thallus was reduced. In hydrated thallus a narrow Lorentzian line coming from loosely bound/free water fraction was recorded. For the temperature range between −5 and −20 °C a discontinuous increase in line halfwidths, accompanied by a decrease in area under the peak, was observed. This was attributed to the cooperative freezing of bulk water present in lichen thallus. In dehydrated thallus the NMR line consists of two components: a narrow, Lorentzian one (coming from loosely bound/free water fraction) and a broad line (from water tightly bound in lichen thallus). The overall area under peak remains unchanged down to −5 °C, and then between −5 and −20 °C it continuously decreases due to non-cooperative water immobilisation. As the temperature is decreased, for temperatures above −5 °C, the contribution made by the broad line component increases at the expense of the narrow line component. The mechanism of loosely-to-tightly bound water transfer is, at least partially, responsible for the freeze-protection of thallus in the lichen species investigated. No significant differences between the freeze protecting loosely-to-tightly bound water transfer mechanism of Antarctic lichens and that of cosmopolitan lichens was noticed.     

Molecular recognition studies with a simple dipyrrinone

We present our investigations of 2-ethyl-3-methyl-(10H)-dipyrrin-1-one, its self-association, and anion binding properties. This receptor is easily accessible in a facile single step synthesis with a straightforward workup. An examination of the concentration dependence of the dipyrrinone NH chemical shifts in CDCl₃ and (CDCl₂)₂ over the temperature range from −20 °C to 100 °C determined the self-association constant to be 3850 M⁻¹. Molecular recognition studies have shown that it has a preference for guests with an OH moiety, such as hydrogen sulfate (HSO₄⁻) and carboxylic acids (RCO₂H).     

Purity control of oxytetracycline by capillary electrophoresis

The applicability of capillary electrophoresis for the purity control of oxytetracycline (OTC) was investigated. OTC is a broad-spectrum antibiotic belonging to the group of the tetracyclines. Several related substances can be present due to fermentation or degradation, such as 4-epioxytetracycline, -apooxytetracycline, β-apooxytetracycline, anhydrooxytet racycline, 2-acetyl-2-decarboxamidooxytetracycline, tetracycline and 4-epitetracycline. Using fused-silica capillaries, the influence of buffer type, buffer pH and buffer concentration were investigated. In all cases 1 mM EDTA was added to prevent metal-ion complexation. The influence of the buffer counter-ion type was examined. Consequently, some instrumental parameters were changed such as capillary length and diameter as well as capillary temperature and applied voltage. The following method is finally proposed: fused-silica capillary, l (effective length) = 38 cm, L (total length) = 44 cm, 50 μm I.D.; buffer, sodium carbonate 20 mM-EDTA 1 mM, pH 11.25; voltage, 10 kV; temperature, 10°C. Linearity, limit of detection and limit of quantitation were determined as well as the relative standard deviations for all the analytes involved. This method is less selective then existing liquid chromatographic methods but it may be used as a complementary tool in purity control and stability studies.     

Chemiluminescence nitrogen detection in ion chromatography for the determination of nitrogen-containing anions

Chemiluminescence nitrogen detection (CLND) provides equimolar response for nitrogen-containing ions such as nitrate, nitrite, cyanide, ammonium and tetradecyltrimethylammonium. Only azide yields a lower response. Nitrite, azide and nitrate are separated on a Dionex AS11 column using 5 mM NaOH as eluent with a 3 μM (1 ng N) limit of detection. Matrices, such as 1:10 diluted seawater, do not degrade these detection limits. CLND also provides equally sensitive (limit of detection 3 μM, 78 ppb) detection of weak acids such, as cyanide, which yield poor sensitivity with suppressed conductivity detection.     

Reduction of Escherichia coli 0157:H7 in shredded iceberg lettuce by chlorination and gamma irradiation

Lettuce was inoculated with a six-strain cocktail of acid-adapted Escherichia coli 0157:H7 at a level of 1×10⁷ CFU/g. Following chlorination at 200 μg/ml, the lettuce was irradiated at 0.15, 0.38, or 0.55 kGy using a ⁶⁰Co source. Survival of E. coli 0157:H7, aerobic mesophiles and yeast and molds were measured over a period of 10 days. For quality analysis, chlorinated lettuce was subjected to irradiation at 0.33 and 0.53 kGy and stored at 1.0°C, 4.0°C or 7.0°C. Changes in texture and color were determined by instrumental means and changes in flavor, odor, and visual quality were determined by sensory testing.

Chlorination plus irradiation at 0.55 kGy produced a 5.4−log reduction in E. coli 0157:H7 levels. Chlorination alone reduced the E. coli 0157:H7 counts by 1–2 logs. Irradiation at 0.55 kGy was also effective in reducing standard plate counts and yeast and mold counts. Irradiation at this level did not cause softening of lettuce and sensory attributes were not adversely affected. In general, appearance and flavor were affected more by the length of storage than by temperature conditions. The 5+log reduction in E. coli counts and lack of adverse effects on sensory attributes indicate that low-dose irradiation can improve the safety and shelf-life of fresh-cut iceberg lettuce for retail sale or food service.     

Determination of sulfur oxyanions by ion chromatography on a silica ODS column with tetrapropylammonium salt as an ion-pairing reagent

The difficulty in using conventional ion chromatography for the determination of sulfate, thiosulfate, dithionate and polythionates (tri-, tetra-, penta- and hexathionate) in their mixtures, comes mainly from very late elutions of polythionates due to their strong retentions onto a separating column. Rapid and sensitive determination of these sulfur oxyanions has been achieved by ion-pair chromatography using a silica octadecylsilane (ODS) column with mobile phases of 10% or 20% (v/v) acetonitrile in water (pH, 5.0) containing 0.2 mM phthalate and 7 mM tetrapropylammonium salt (TPAOH). The sulfur species separated on the column were monitored with a conductivity detector after passing through a micro membrane suppressor in the H⁺ form. When an acetonitrile-water (10:90, v/v) mobile phase (pH, 5.0) of 0.2 mM phthalate and 7 mM TPAOH was used at a flow-rate of 0.8 ml min⁻¹, sulfate, thiosulfate, dithionate and trithionate were eluted at short retention times of 9.1, 9.7, 11.4 and 15.8 min, respectively; however, the higher polythionates required more than 30 min to elute. When the concentration of acetonitrile in the mobile phase was raised to 20% (v/v), all polythionates of tri- to hexathionate were completely separated from their mixtures within 21 min; in this instance, both sulfate and thiosulfate failed to be resolved due to their close retention times. Good recoveries were obtained for these sulfur oxyanions when added to various hot-spring water samples.     

Adsorption of Pseudomonas putida on clay minerals and iron oxide

Adsorption of Pseudomonas putida on minerals including montmorillonite, kaolinite and goethite was studied. The adsorption isotherms of P. putida on the examined minerals conformed to the Langmuir equation. The amount of P. putida adsorbed followed the order: goethite > kaolinite > montmorillonite. A greater extent of P. putida adsorption on minerals was observed in the range of temperature from 15 to 35 °C. The adsorption of P. putida on minerals decreased with the increase of pH from 3.0 to 10.0. Magnesium ion was more efficient than sodium ion in promoting P. putida adsorption on minerals. The results suggest that electrostatic interactions play a vital role in P. putida adsorption by soil colloidal factions. The information obtained in this study is of fundamental significance for the understanding of the survival and transport of bacteria in soil systems.     

On-line concentration of s-triazine herbicides in micellar electrokinetic chromatography using a cationic surfactant

A new method for the simultaneous determination of anions (sulfate, nitrate, and chloride) and cations (sodium, ammonium, potassium, magnesium, and calcium) in acid rain waters was investigated using high-performance ion-exclusion/cation-exchange chromatography with conductimetric detection on a separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin in the hydrogen-form and an eluent comprising 1.5 mM sulfosalicylic acid–6 mM 18-crown-6 at pH 2.6, operated at 1.5 ml/min. Effective separation and highly sensitive conductimetric detection for the anions and the cations was achieved in about 14 min. Since the ionic balance (equivalents of anions/equivalents of cations) of acid rain waters of different pH (4.40–4.67) ranged from 0.97 to 0.94, evaluation of the water quality of acid rain was possible. This method was successfully applied to the simultaneous determination of the anions and the cations in acid rain transported from mainland China and North Korea to central Japan monitored by a meteorological satellite data analyzer.     

Capacity gradient anion chromatography with a borate complex as eluent

Complex formation between borate compounds and vicinal diols is well recognized. Generally, in a chemically bonded anion-exchange resin, many hydroxyl groups are introduced on the surface of the resin in order to make the resin hydrophilic. The borate as an eluting reagent also reacts to these hydroxyl groups, and this complex formation decreases the apparent ion-exchange capacity of the column by being dissociated to the anion depending on the eluent pH. In the present work a method is described for the simultaneous determination of anions based on the capacity gradient for suppressed ion chromatography. A Tosoh IC-Anion-PW column and dihydroxyphenylborane–mannitol eluent system were used. To maintain baseline stability, it was helpful to keep the borate concentration constant during a gradient of 16 to 0 mM mannitol as a modifier to prevent the complex formation with the hydroxyl on the resin. The chemical composition of the eluents and gradient profiles are discussed and the application to the analysis of the condensed phosphates with widely varying retention times as food additives in a cheese sample is presented.