Scanning tunneling microscopy and spectroscopy investigations of copper phthalocyanine adsorbed on Al2O3/Ni3Al(1 1 1)

Low temperature scanning tunneling microscopy (LT-STM) and scanning tunneling spectroscopy (STS) have been used to investigate adsorbed copper phthalocyanine (C₃₂H₁₆N₈Cu) molecules on an ordered ultrathin Al₂O₃ film on the Ni₃Al(1 1 1) surface as a function of coverage and annealing temperature. For sub-monolayer coverage and a deposition temperature of 140 K two different planar molecular adsorption configurations rotated by 30° with respect to each other were observed with submolecular resolution in the STM images. The template effect of the underlying oxide film on the CuPc orientation, however, is only weak and negligible at higher coverages. For θ_CuPc ≈ 1 ML, before completion of the first layer, the growth of a second layer was already observed. The measured spacing of 3.5 Å between first and second layer corresponds to the distance between the layers in the α-modification of crystalline CuPc. The molecules deposited at 140 K are thermally stable upon prolonged annealing to temperatures up to 250 K. By the use of STS the lowest unoccupied molecular orbital (LUMO) of the adsorbed copper phthalocyanine molecules has been identified at an energy of 1.2 eV above E_F. The lateral distribution of the electronic states of the CuPc has been analyzed and mapped by STS.     

Point defects along metallic atomic wires on vicinal Si surfaces: Si(5 5 7)–Au and Si(5 5 3)–Au

Point defects on the metallic atomic wires induced by Au adsorbates on vicinal Si surfaces were investigated using scanning tunneling microscopy and spectroscopy (STM and STS). High-resolution STM images revealed that there exist several different types of defects on the Si(5 5 7)–Au surface, which are categorized by their apparent bias-dependent images and compared to the previous report on Si(5 5 3)–Au [Phys. Rev. B (2007) 205325]. The chemical characteristics of these defects were investigated by monitoring them upon the variation of the Au coverage and the adsorption of water molecules. The chemical origins and the tentative atomic structures of the defects are suggested as Si adatoms (and dimers) in different registries, the Au deficiency on terraces, and water molecules adsorbed dissociatively on step edges, respectively. STS measurements disclosed the electronic property of the majority kinds of defects on both Si(5 5 7)–Au and Si(5 5 3)–Au surfaces. In particular, the dominating water-induced defects on both surfaces induce a substantial band gap of about 0.5 eV in clear contrast to Si adatom-type defects. The conduction channels along the metallic step-edge chains thus must be very susceptible to the contamination through the electronic termination by the water adsorption.     

Scanning tunneling microscopy/spectroscopy study of adsorption of C<Subscript>60</Subscript>F<Subscript>36</Subscript> molecules on the 7 × 7-Si(111) surface

Spatially resolved images of an individual C₆₀F₃₆ fluorofullerene molecules on Si(111)-7 × 7 surface have been obtained by means of scanning tunneling microscopy/spectroscopy (STM/STS). The presence of isomers with different symmetry (T, C ₃, C ₁) has been revealed in STM investigation of initial adsorption stage of C₆₀F₃₆ on silicon surface Si(111)-(7 × 7). The adsorbed fluorofullerene molecule can occupy any adsorption site of silicon surface (corner site, faulted half, unfaulted half) that indicates for strong molecule-substrate interaction. The HOMO-LUMO gap of the adsorbed C₆₀F₃₆ molecules have been estimated from current image tunneling spectroscopy (CITS) and z(V) with engaged feedback measurements. The value of HOMO-LUMO gap observed experimentally was 3 eV. The C₆₀F₃₆ molecules adsorption on Si(111)-(7 × 7) surface was stable and kept equilibrium configuration during several hours.     

利用STM和CV方法测定有机发光材料的能带参数

利用扫描隧道显微镜/扫描隧道谱(STM/STS)的技术,研究了有机发光材料Alq₃、DPN-2CN和DNP-2CN的表面电子结构。将材料DPN-2CN和DNP-2CN的表面电子结构与Alq₃的表面电子结构进行对比,判定了DPN-2CN和DNP-2CN的最低空轨道(LUMO)能级。通过电化学循环伏安(CV)法,对DPN-2CN和DNP-2CN的LUMO能级和最高占有轨道(HOMO)能级进行了表征。两种测试方法所得到的LUMO能级参数基本一致。     

Scanned-probe topological and spectroscopic study of surface states on clean and Si-deposited GaAs (0 0 1)-c(4×4) surfaces

Microscopic topological and spectroscopic properties of MBE-grown GaAs c(4×4) surfaces without and with monolayer Si deposition were investigated by the scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). Empty state STM images on as-grown surface showed bright and dark cells, and they exhibited strong correlation with the spatial distribution of normal and anomalous conductance gaps of the STS spectra. Bias dependent STM images indicated presence of pinning areas with continuous space and energy distribution of surface gap states. By deposition of monolayer Si, dark areas reduced a great deal and the rate of finding normal STS spectra increased, indicating large reduction of surface states.     

Structure and electronic properties of ultrathin Co films on W(1 1 0)

The structure and electronic properties of ultrathin Co films on W(1 1 0) grown by molecular beam epitaxy in UHV were investigated by low energy electron diffraction (LEED) and scanning tunneling microscopy and spectroscopy (STM and STS). For coverages above 0.7 ML the pseudomorphic (ps) monolayer is transformed gradually into close-packed (cp-) monolayer areas, showing up as separated islands that increase in size with coverage until the cp-monolayer is complete. Two different structures of the cp-monolayer were observed by atomically resolved STM, both leading to a 8 × 1 superstructure in the LEED pattern. Higher coverages continue to grow in the Stransky–Krastanov growth mode forming simultaneously double layer islands and triple layer islands in fcc(1 1 1) and hcp(0 0 0 1) stacking. STS reveals tunneling spectra that differ considerably depending on the thickness and on the structure. Two different classes of triple layer islands can be distinguished by a resonant peak at +0.3 eV appearing in only one of the two classes. We attributed this behavior to a different stacking according to a fcc or hcp structure.     

Interplay between metal-free phthalocyanine molecules and Au(110) substrates

Metal-free phthalocyanine (Pc) molecules adsorbed on the Au(110) surface have been studied both experimentally (STM, LEED) and with density functional calculations. A strong interaction between substrate and adsorbate is observed. On the one hand, a clear template effect of the anisotropic substrate is observed: already at low coverages, the Pc molecules adsorb in various typical row patterns. On the other hand, the molecular adsorption modifies the substrate: at coverages higher than 0.25 monolayers, the usual (1 × 2) reconstruction is converted to a (1 × 3) reconstruction. First principle DFT calculations yield adsorption geometries that agree with the measured STM images and adsorption energies in the range of 2–3 eV. The adsorption leads to covalent and van der Waals interactions between adsorbate and substrate and is accompanied by a considerable charge transfer.     

tetracene 分子在Ru(1010)表面的吸附结构及其电子态研究

利用紫外光电子能谱(UPS)、角分辨紫外光电子能谱(ARUPS)和扫描隧道显微镜(STM)等方法研究了tetracene分子在Ru(1010)表面上吸附的电子态，吸附位置和吸附取向.UPS实验显示，与tetracene分子有关的光电子谱峰在费米能级以下2.1, 3.5, 4.8, 6.0, 7.1和9.2 eV处；ARUPS 结果表明，tetracene分子的分子平面基本平行于衬底表面；从STM图像中可以看到tetracene分子的长轴沿［0001］和［1210］两个晶向.基于密度泛函理论的从头算计算证实了上述结论.当分子长轴沿［0001］晶向时，分子中心位置在衬底表面的“短桥位”上，当分子长轴沿［1210］晶向时，分子中心位置在衬底表面的“四原子中心空位”上. 关键词： tetracene分子 Ru(1010)表面 吸附结构 吸附电子态     

Bias dependence of apparent layer thickness and Moiré pattern on NaCl/Cu(001)

Bias-dependent features of the insulating NaCl layer grown on Cu(001) have been investigated by scanning tunneling microscopy/spectroscopy (STM/STS). The apparent layer thickness of the NaCl film is variable at bias voltages ranging from 2.8 to 3.2 V as well as from 4.0 to 5.0 V, and the Moiré pattern induced by NaCl–Cu lattice mismatch also shows bias dependence. The z–V (dz/dV–V) curves and dI/dV mapping measurements reveal that the resonant tunneling between the image potential states (IPSs) on Cu(001) and the Fermi level of the STM tip leads to drastic variations of these features.     

Investigation of the Shockley surface state on clean and air-exposed Au (1 1 1)

Scanning tunneling microscopy (STM) and spectroscopy (STS) carried out in vacuum and air were used to study the electronic structure of the Au (1 1 1) surface in the range of 0.0-0.7 eV below the Fermi level. The STS experiment carried out in UHV showed the existence of the Shockley surface state (SS) located 0.48 eV below the Fermi level. STS carried out in air showed strong local maximum located 0.35 eV below the Fermi level. This maximum was ascribed to the SS shifted toward lower energy due to carbon and oxygen overlayer. To confirm that the SS could exist on the sample exposed to air we did ultraviolet photoemission spectroscopy (UPS) experiment on air-treated and clean Au (1 1 1). Our results suggest that the SS position initially measured at 0.38 eV below the Fermi level was shifted to 0.27 eV after air treatment. Additionally, the level of contamination was measured using X-ray photoelectron spectroscopy (XPS).     

Scanning tunneling microscopy on iron-chalcogenide superconductor Fe(Se, Te) single crystal

We have investigated the iron-chalcogenide superconductor Fe(Se, Te) using a low-temperature scanning tunneling microscopy/spectroscopy (STM/STS) technique. STM topography at 4.9 K shows clear regular square arrangements of spots with the lattice spacing ～0.37 nm, from which what we observe are attributed to Se or Te atomic plane. In the topography, brighter and darker atomic spots are randomly distributed, which are most probably due to Te and Se atoms, respectively. For the FeTe compound, the topography exhibits clusters of the bright spots probably arising from separated iron atoms distributing over several Te lattice sites. The STS measurements clarify the existence of the large-size gap with 2Δ = 0.4–0.6 eV.     

Metallic nature of the alpha-Sn/Ge(111) surface down to 2.5 K

Low temperature (down to 2.5 K) scanning tunneling microscopy (STM) and spectroscopy (STS) measurements are presented to assess the nature of the alpha-Sn/Ge(111) surface. Bias-dependent STM and STS measurements have been used to demonstrate that such a surface preserves a metallic 3 x 3 reconstruction at very low temperature. A tip-surface interaction mechanism becomes active below about 20 K at the alpha-Sn/Ge(111) surface, resulting in an apparent unbuckled (sqrt[3] x sqrt[3]) reconstruction when filled states STM images are acquired with tunneling currents higher than 0.2 nA.     

Photoluminescence properties of a near-stoichiometric CuGaSe2 film

Epitaxial films of CuGaSe₂ were grown on (001)GaAs substrates by an MBE technique. A near-stoichiometric film with chemical compositions consistently varied from Cu- to Ga-rich was prepared by growing the film without the substrate rotation. A series of PL spectra was obtained by directing a focused laser beam point-by-point across the boundary separating the Cu- and Ga-rich regions. Distinct features of these spectra were noted. On the Cu-rich side, optical emissions peaked at 1.71, 1.67, 1.63, and 1.59 eV were observed in a PL spectrum. The peak at 1.71 eV was due to the emission of bound exciton, while the peak at 1.67 eV was caused by the free-to-bound transition. The other two peaks were identified to be the donor-to-acceptor emissions. Further annealing experiments performed in different environments suggested that the peaks at 1.67, 1.63, and 1.59 eV were associated with the optical transitions of CB→Cu_Ga, Cu_i→Cu_Ga, and Cu_i→V_Ga, respectively. On the Ga-rich side, a dominant donor-to-acceptor emission peaked at 1.62 eV was observed, which was determined to be the Ga_Cu→V_Cu transition. The two defects with opposite charge states resulted in a highly compensated material with high resistivity.     

STM analysis of triosmium carbonyl cluster adsorption at HOPG

The study of metallic carbonyl clusters as precursors in tailoring the heterogeneous metal catalysts has been of great importance. The catalytic nature of the adsorbed clusters in thin film form depends on the chemical properties of the substrate used. The metal-support interaction will determine various properties such as the surface morphology, adsorption features and the structural orientations. We report a scanning tunneling microscopy (STM) study of an osmium carbonyl cluster (Os₃(CO)₁₁(NCCH₃)) adsorbed on highly oriented pyrolytic graphite (HOPG). STM measurements showed that the osmium carbonyl cluster interacts with HOPG in such a way that it adsorbs on the basal plane showing regular lattice structure, whereas the axial planes of the HOPG surface shows no ordered structure. The regular cluster lattice structure of the carbonyl cluster on the basal plane of the graphite has lattice parameters of a=1.4 nm and b=1.5 nm. We believe that the regular orientation of the cluster indicates a monolayer adsorption of the cluster on the graphite basal planes. Scanning tunneling spectroscopy (STS) measurements also indicated an insulating behavior for the cluster molecules on HOPG, with a significant energy gap value of ca. 300 mV. The cluster interaction at the active sites, i.e. axial planes of the graphite, was also observed by in situ STM measurements.     

Spatial resolution of imaging contaminations on the GaAs surface by scanning tunneling microscope-cathodoluminescence spectroscopy

We obtained the luminescence image of the GaAs (1 1 0) surface by scanning tunneling microscope-cathodoluminescence (STM-CL) spectroscopy, where low-energy (∼100 eV) electrons field emitted from the STM tip were used as a bright excitation source. The STM-CL image with high photon signal (1.25 × 10⁴ cps) showed the dark image corresponding to the surface contamination in the STM image working as the nonradiative recombination centers of carriers. This dark image demonstrated the spatial resolution of about 100 nm in STM-CL spectroscopy of the GaAs (1 1 0) surface, which was determined by the field-emitted electron beam diameter.     

La0.67Ca0.33MnO3(001)薄膜表面结构的扫描隧道显微术研究

利用Scanning Tunneling Microscope(STM)和Scanning Tunneling Spectroscopy(STS)技术研究了La_0.67Ca_0.33MnO₃(001)表面性质,研究发现表面呈现多相分离现象,在锰氧终端面观察到了绝缘性的( 2 × 2 )R45°重构表面和金属性的(1×1)重构表面,在镧钙氧终端面,观察到了表面呈现条纹状结构.La_0.67Ca_{0.33 关键词： 镧钙锰氧薄膜 终端面 绝缘金属转变}     

Channel selective scanning tunneling spectroscopy

In this paper we simulate STM and STS experiments for CO monomers and dimers on Cu(1 1 1) surface. We show that the contrast of STM images can be attributed to interference effects between tunneling channels, and suggest that functionalizing the microscope tip improves the channel selectivity of STM. Furthermore, we show that voltage and position dependent tunneling spectra also reflect the same interference effects, but adds the energy resolution to the channel analysis. Especially in the case of nonresonant tunneling, STS measures local density of states only indirectly. The present study suggests that STS in constant height mode can be used in investigating the phase and energy sensitivity of tunneling channels in adsorbate molecules and nanostructures.     

Mechanisms of reversible conformational transitions in a single molecule

The reversible interconversion between two nonplanar conformations of single Zn(II) Etioporphyrin I molecules adsorbed on a NiAl(110) surface at 13 K was induced by a scanning tunneling microscope (STM). The threshold voltage for the conformational change at negative sample bias depends linearly on the tip-sample distance, suggesting an electrostatic force mechanism. The reverse conversion involves inelastic electron tunneling via a molecular electronic resonance at 1.25 eV. In contrast with the photon-induced conformational changes, an electrically induced mechanism is realized with the STM.     

Negative-differential conductivity measured on a germanium layer on Si(001)

The morphology and the electronic structure of heteroepitaxial germanium layers grown pseudomorphically by solution epitaxy on Si(001) has been investigated by scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). A significant decrease of tunneling current at a sample voltage of 1.5 V is observed in areas of 0.5 nm diameter between dimer rows. This decrease is due to a negative-differential conductivity at a tunnel diode configuration consisting of a surface defect structure of the germanium layer and the STM tungsten tip.     

Bistability of single 1,5 cyclooctadiene molecules on Si(001)

The adsorption and current-induced bistability of single 1,5 cyclooctadiene molecules on Si(001) were studied in ultrahigh vacuum by low-temperature scanning tunneling microscopy (STM). After a dosage of ≈0.05 L at room temperature followed by cooling to the measuring temperature of 7 K, we find that the cyclic alkene molecule preferably adsorbs in the bridge structure with both C=C double bonds reacting with two adjacent Si dimers via [2+2] cycloaddition reaction. The time-dependent current measured upon tunneling through the adsorbed molecule at fixed STM tip height displays a switching between two current levels with the same mean residence time in each level. Higher bias and/or reduced tip height—and therefore higher current—increase the switching rate, suggesting that the reversible switching is due to inelastic electron tunneling. The observed bistability is interpreted as a dynamic interconversion between two degenerate conformations of the adsorbed molecule.