Hybridization of Nafion membranes with an acid functionalised polysiloxane: Effect of morphology on water sorption and proton conductivity

Polysiloxane-modified hybrid Nafion membranes were prepared by casting a mixture of Nafion solution and a precursor of acid functionalised polysiloxane based on tetraethoxysilane and a mercaptan-organoalkoxysilane.Scanning Electron Microscopy (SEM) and Atomic Force Microscopy analysis revealed that the functionalised polysiloxane was dispersed either as finely nanosized inclusions or as coarse domains depending on the rate of the solvent evaporation during the casting procedure. In particular the slower is the rate of solvent evaporation the more interpenetrated and homogenously dispersed at nanosized level is the polysiloxane inside the Nafion membrane.The hybridization process increases the thermal stability of the membranes of about 50 °C relatively to the unmodified Nafion. Small angle X-ray scattering (SAXS) analysis reveals that the hybrid membranes exhibited the typical morphology of Nafion consisting of distinct hydrophilic and hydrophobic domains.Water vapor sorption and proton conductivity were measured varying the temperature (up to 120 °C) and the water activity conditions (from 0.1 to 0.8). The polysiloxane network always increases the water vapor uptake of the membranes and increases significantly the proton conductivity at higher temperature depending on the type of morphology developed by the manufacturing method. In particular hybrid membranes exhibiting nanosized polysiloxane dispersion show a proton conductivity which is up to one-and-half time higher than Nafion recast membrane at high temperature and low water content.     

Polysulfone ionomers for proton-conducting fuel cell membranes: sulfoalkylated polysulfones

Polysulfones (PSUs) carrying short pendant alkyl side-chains with terminal sulfonic acid units have been prepared and studied as proton-conducting membrane materials. The first step in the preparation involved quenching of lithiated PSU with SO₂ gas, resulting in sulfinated PSU. In the second step, the lithium sulfinate units on the polymer were reacted with sodium 2-bromoethanesulfonate, sodium 3-bromopropanesulfonate, or 1,4-butane sultone to produce sulfoethylated, sulfopropylated, or sulfobutylated PSUs, respectively. Analysis by thermogravimetry showed that membranes based on the sulfoalkylated polymers were stable up to approximately 300 °C under N₂ atmosphere. Calorimetry measurements revealed that the modified polymers absorbed large amounts of non-freezing water, corresponding to 11–14 mol H₂O/mol SO₃H under immersed conditions. The proton conductivity of a membrane based on a PSU carrying 0.9 sulfopropyl chains per repeating unit was measured to be 77 mS/cm at 70 °C under humidifying conditions.     

Sulfonated poly(arylene ether sulfone) ionomers containing fluorenyl groups for fuel cell applications

A series of sulfonated poly(arylene ether sulfone)s (SPEs) containing fluorenyl groups as bulky components were synthesized and characterized for fuel cell applications. Introduction of disodium 3,3′-disulfo-4,4′-difluorophenyl sulfone (SFPS) monomer gave ionomers with high acidity and accordingly high proton conductivity as well as high proton diffusion coefficient (D_σ) at low humidity. The membrane of SPE60 (where the number denotes mole percentage of the component containing sulfonic acid groups; IEC (ion exchange capacity) = 1.68 mequiv./g) exhibited high proton conductivity of 4.6 × 10⁻³ S/cm at 40% RH and 80 °C, which is one order of magnitude higher than that (6 × 10⁻⁴ S/cm) of our previous SPE (SPE-1, IEC = 1.58 mequiv./g). D_σ of SPE60 membrane was ca. 4 times higher than that of the SPE-1 membrane at low water volume fraction. SPE membranes showed good oxidative and hydrolytic stability as well as favorable thermal and mechanical properties. Small-angle X-ray scattering analyses showed that the phase separation of SPE membranes was much less developed than that of the perfluorinated Nafion membrane which accounts for lower hydrogen and oxygen permeability of the former membranes.     

Poly(styrene-co-acrylonitrile) based proton conductive membranes

Sulfonated poly(styrene-co-acrylonitrile) (PSAN–SO₃H) membranes were obtained by sulfonation of the original styrene–acrylonitrile copolymer, in different molar ratios, and characterized by vibrational spectroscopy (FTIR), thermal analyses (TGA and DSC) and electrochemical impedance spectroscopy (EIS). The thermal stability of the sulfonated polymers exhibited a dependence on the sulfonation degree and reached 261 °C for samples up to 1:4 (sulfonating agent to styrene unit). FTIR spectra showed the covalent incorporation of sulfonic groups at the styrene units, confirming the PSAN–SO₃H formation. Vibrational spectra also indicated the presence of hydronium ions and dissociated sulfonic groups, indicating the existence of mobile protons for ion conduction. DSC analyses evidenced two glass transition temperatures (T_g), one associated with an ion-water domain and other with the chain backbone glass transition. The maximum conductivity of PSAN–SO₃H membranes at ambient temperature was about 10⁻³ Ω⁻¹ cm⁻¹, achieving 10⁻² Ω⁻¹ cm⁻¹ at 80 °C. The conductivity dependency on the temperature was found to be linear, similarly to other sulfonic acid polymers described on the literature, and the water uptake reaches 45.7% of the polymer mass, against 18.9% of the original copolymer.     

Preparation of Nafion/sulfonated poly(phenylsilsesquioxane) nanocomposite as high temperature proton exchange membranes

Nafion/sulfonated poly(phenylmethyl silsesquioxane) (sPPSQ) composite membranes are fabricated using homogeneous dispersive mixing and a solvent casting method for direct dimethyl ether fuel cell (DDMEFC) applications operated above 100 °C. The inorganic conducting filler, sPPSQ significantly affects the characteristics in the nanocomposite membranes by functionalization with an organic sulfonic acid to PPSQ. Moreover, sPPSQ content plays an important role in membrane properties such as microstructure, proton conductivity, fuel crossover, and single cell performance test. With increasing sPPSQ content in the nanocomposite membrane, the proton conductivity increased and fuel crossover decreased. However, in a higher temperature range above 110 °C, Nafion/sPPSQ 5 wt.% composite membrane has the highest proton conductivity. Also, the DME permeability for the composite membrane with higher sPPSQ content increased sharply. The excessive sPPSQ content caused a large aggregation of inorganic fillers, leading to the deterioration of membrane properties. In this study, the optimal sPPSQ content for maximizing the DDMEFC performance was 5 wt.%. Our nanocomposite membranes demonstrated proton conductivities as high as 1.57 × 10⁻¹ S/cm at 120 °C, which is higher than that of Nafion. The cell performances were compared to Nafion/sPPSQ composite membrane with Nafion 115, and the composite membrane with sPPSQ yielded better cell performance than Nafion 115 at temperatures ranging from 100 to 120 °C and at pressures from 1 to 2 bar.     

Preparation and characterization of sulfated zirconia (SO4/ZrO2)/Nafion composite membranes for PEMFC operation at high temperature/low humidity

Fine particle superacidic sulfated zirconia (SO₄²⁻/ZrO₂, S-ZrO₂) was synthesized by ameliorated method, and composite membranes with different S-ZrO₂ contents were prepared by a recasting procedure from a suspension of S-ZrO₂ powder and Nafion solution. The physico-chemical properties of the membranes were studied by ion exchange capacity (IEC) and liquid water uptake measurements, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, thermogravimetry–mass spectrometry (TG–MS) and Fourier transform infrared (FT-IR) spectroscopy. The results showed that the IEC of composite membrane increased with the content of S-ZrO₂, S-ZrO₂ was compatible with the Nafion matrix, the incorporation of the S-ZrO₂ could increase the crystallinity and also improve the initial degradation temperature of the composite membrane. The performance of single cell was the best when the S-ZrO₂ content was 15 wt.%, and achieved 1.35 W/cm² at 80 °C and 0.99 W/cm² at 120 °C based on H₂/O₂ and at a pressure of 2 atm, the performance of the single cell with optimized S-ZrO₂ was far more than that of the Nafion at the same condition (e.g. 1.28 W/cm² at 80 °C, 0.75 W/cm² at 120 °C). The 15 wt.% S-ZrO₂/Nafion composite membrane showed lower fuel cell internal resistance than Nafion membranes at high temperature and low relative humidity (RH).     

Sulfonated poly(arylene thioether phosphine oxide)s copolymers for proton exchange membrane fuel cells

High molecular weight sulfonated poly(arylene thioether phosphine oxide)s (sPATPO) with various sulfonation degrees were prepared directly by aromatic nucleophilic polycondensation of 4,4′-thiobisbenzenethiol with sulfonated bis(4-fluorophenyl) phenyl phosphine oxide and bis(4-fluorophenyl) phenyl phosphine oxide. sPATPO in the acid form with sulfonation degrees of 60–100% exhibits a glass transition temperature higher than 230 °C and a 5% weight loss temperature above 400 °C, indicating high thermal stability. sPATPO with a high sulfonation degree shows high proton conductivity and good resistance to swelling as well. For instance, sPATPO-70 displays the conductivity of 0.0783 S/cm and a swelling ratio of 11.6% at 90 °C. TEM micrographs showed that sPATPO membranes with a high sulfonation degree could form continuous ion channels, which are favorable for improving the proton conductivity but harmful to remaining the mechanical property. The membranes are expected to show good performances in fuel cell applications.     

磺化酚酞型聚醚砜膜的制备及其阻醇和质子导电性能

直接甲醇燃料电池 (Directmethanolfuelcell,DMFC)以高效、清洁和燃料储运方便等优点适宜于作为各种用途的可移动动力源 ,成为 2 0世纪 90年代以来研究与开发的热点[1,2 ] .目前 ,这种电池的研究难点主要集中在催化剂不稳定和质子交换膜透醇上 .一张好的DMFC膜不但要可传递质子、绝缘电子 ,还应具有良好的阻醇性能 .如果膜的阻醇性能不好 ,甲醇会穿过膜到达阴极 ,与氧直接反应而不产生电流 ,不但造成燃料的浪费 ,同时也影响阴极的正常反应 ,使电池效率下降[3 ] .目前广泛应用于燃料电池中的Nafion 系列膜是由美国DuPont公司生产的一种…     

侧链磺化聚芳醚质子交换膜的研究进展

燃料电池是以氢气、甲醇等作为燃料的一种新型能量转化装置,其中质子交换膜燃料电池（Proton Exchange Membrane Fuel Cell, PEMFC）凭借其能量功率高、启动速度快和使用寿命长等优点已经在移动电源、潜艇和电动汽车等领域得到了广泛应用。质子交换膜（Proton Exchange Membrane, PEM）对PEMFC的性能影响最大,高效的PEMFC需要PEM具有高的质子电导率、良好的热稳定性和机械性能、低燃料渗透率以及优异的物理化学稳定性等。目前市面上多数使用的均是具有优异质子电导率的Nafion系列膜,但其存在制备困难、成本昂贵、质子电导率严重依赖湿度等缺点,在一定程度上限制了其发展。为了让PEM有更多的选择,科学家一直专注于使用新材料替代Nafion膜。近年来,科学家们模拟Nafion结构,通过合成各种侧链含磺酸基团的聚芳醚结构,使得亲水基团磺酸基和疏水基团之间形成微相分离结构,从而获得了一系列具有优异综合性能的PEM。本文将重点对侧链烷基磺化型、侧链磺化嵌段型、侧链局部密集磺化型、侧链磺化交联型和侧链磺化复合型这几种常见策略的合成方法及性能进行了综述,最后展望了侧链磺化聚芳醚在PEM领域的优势及发展前景。     

Preparation and characterization of crosslinked PVA/SiO2 hybrid membranes containing sulfonic acid groups for direct methanol fuel cell applications

Organic–inorganic hybrids based on poly(vinyl alcohol) (PVA)/SiO₂ hybrid membranes containing sulfonic acid groups were prepared using the sol–gel process under acidic conditions. The PVA/sulfosuccinic acid (SSA)/silica hybrid membranes were fabricated from different SSA contents. The proton conductivity and methanol permeability of the hybrid membranes were studied with changing SSA content from 5 to 25 wt.%. It was found that the proton conductivity and the methanol permeability were dependent on the SSA content both as a crosslinking agent, and as a donor of the hydrophilic SO₃H group. Up to an SSA content of about 20 wt.%, both of these properties decrease, and above this SSA content, they begin to increase with increasing SSA content. The proton conductivities of the PVA/SSA/silica membranes were in the range of 10⁻³ to 10⁻² S/cm, and the methanol permeabilities ranged between 10⁻⁸ and 10⁻⁷ cm²/s. The presence of silica particles in the organic polymer matrix, which reduce the free water ratio of the membranes, results in hybrids with markedly reduced methanol permeabilities. These characteristics of the PVA/SSA/silica hybrid membranes are desirable for future applications related to direct methanol fuel cells.     

Modification of proton conductive polymer membranes with phosphonated polysilsesquioxanes

New hybrid membranes for fuel cell applications based on sulfonated poly(ether ether ketone) (SPEEK) and phosphonated polysilsesquioxanes were synthesized. The impedance spectroscopy measurements show an increase of the proton conductivity for all studied composites, in comparison to plain SPEEK. For hybrid membranes containing 20 wt% of polysilsesquioxane with 80 mol% of phosphonated units the conductivities can reach values that are similar to Nafion 117^® at 100% RH. The best results of proton conductivity (142 mS/cm) were obtained for composites with 40 wt% of the same polysilsesquioxane at 120 °C also at 100% RH.     

直接甲醇燃料电池新型聚合物膜的研究

通过溶液共混方法 ,制备了聚偏氟乙烯与聚苯乙烯磺酸 (PVDF_PSSA)、聚偏氟乙烯与Nafion(PVDF_Nafion)两种共混膜 .研究了膜组成对膜电导率和甲醇透过率的影响 .与Nafion 1 1 7膜相比 ,PVDF_Nafion共混膜在Nafion含量为 2 5wt%时 ,电导率σ下降 2个数量级 ,而甲醇透过率P却降低 3个数量级 .若以 (σ/P)为综合指标 ,则PVDF_Nafion共混膜和PVDF_PSSA共混膜的综合性能分别比Nafion 1 1 7膜高约 4 0倍、1 6倍     

Heterogeneous ion-exchange membranes based on sulfonated poly(1,4-phenylene sulfide) and linear polyethylene: preparation, oxidation stability, methanol permeability and electrochemical properties

Poly(1,4-phenylene sulfide) was sulfonated with chlorosulfonic acid in 1,2-dichloroethane. The product (IEC = 2.38 mequiv./g) was ground and sieved (mesh size 63 μm) to obtain small particles. The particles and linear polyethylene were mixed in various ratios and the resulting blends were press-molded at 150 °C to obtain the membranes. Membranes containing up to 66 wt.% of sulfonated particles could be prepared without any problem in mechanical strength. The membranes were characterized by their stability in oxidative environment, ionic conductivity, and diffusive permeability to methanol. The membrane containing 66 wt.% of sulfonated particles was almost as conductive as Nafion 117; it exhibited, however, much lower diffusive permeability to methanol. In a strongly oxidative environment (3% aqueous H₂O₂ at 70 °C), the prepared membranes were less stable than Nafion 117, but much more stable than membranes with sulfonated poly(styrene-co-divinylbenzene) particles. In preliminary laboratory tests with H₂/O₂ and direct methanol fuel cells, the prepared membranes with high concentrations of sulfonated particles performed similarly to Nafion 117.     

Synthesis and characterization of poly(aryl ether ketone) ionomers with sulfonic acid groups on pendant aliphatic chains for proton-exchange membrane fuel cells

A series of parent poly(aryl ether ketone)s bearing different content of unsaturated pendant propenyl groups were synthesized via nucleophilic substitution polymerization from 3,3′-diallyl-4,4′-dihydroxybiphenyl, 9,9′-bis(4-hydroxyphenyl) fluorene and 4,4′-difluorobenzophenone. The polymers with pendant aliphatic sulfonic acid groups were further synthesized by free radical thiol-ene coupling reactions between 3-mercapto-1-propanesulfonic sodium and the parent propenyl functional copolymers. The resulting sulfonated polymers with high inherent viscosity (1.83-4.69 dL/g) were soluble in polar organic solvents and can form flexible and transparent membranes by casting from their solutions. The copolymers with different ion exchange capacity could be conveniently synthesized by varying the monomers ratios. Transmission electron microscopy (TEM) was used to examine the microstructures of the membrane and the results revealed that significant hydrophilic/hydrophobic microphase separation with spherical, uniform-sized (5-10 nm) and well-dispersed hydrophilic domains was afforded. The proton conductivities of the as-prepared membranes and the state-of-the-art Nafion 117 membrane in fully hydrated state were investigated. The results revealed that the proton conductivity of the synthesized membranes increased more remarkably than that of Nafion 117 membrane with increasing temperature. The membrane with 1.69 mequiv/g of IEC had a conductivity of 2.5 × 10⁻² Scm⁻¹ at 100 °C. The membranes also possessed excellent mechanical properties, good thermal, oxidative, hydrolytic and dimensional stabilities.     

聚苯并咪唑/聚乙烯吡咯烷酮复合质子交换膜的制备及钒液流电池性能

将聚苯并咪唑(PBI)与聚乙烯吡咯烷酮(PVP)共混, 制备了一系列PBI/PVP复合质子交换膜, 研究了不同PVP含量对PBI/PVP复合质子交换膜性能的影响. 研究结果表明, PVP的加入可有效提高PBI/PVP复合质子交换膜的吸水率及硫酸吸附量, 从而提高质子电导率, 与PBI原膜相比, PBI-PVP-5复合质子交换膜的结合酸含量可达2.47 mmol/g, 质子电导率达4.81 mS/cm, 选择性(3.12×10⁵ S·min/cm³)远高于原膜(1.12×10⁵ S·min/cm³). 电流密度为120 mA/cm²时, 电池的电压效率(VE)和能量效率(EE)均较PBI原膜提高了10%, 电池自放电时间长达307 h. PVP的加入为PBI系列钒液流电池隔膜提供了一个提高质子电导率的新思路.     

The direct synthesis of dimethyl ether from syngas over hybrid catalysts with sulfate-modified γ-alumina as methanol dehydration components

A series of γ-Al₂O₃ samples modified with various contents of sulfate (0–15 wt.%) and calcined at different temperatures (350–750 °C) were prepared by an impregnation method and physically admixed with CuO–ZnO–Al₂O₃ methanol synthesis catalyst to form hybrid catalysts. The direct synthesis of dimethyl ether (DME) from syngas was carried out over the prepared hybrid catalysts under pressurized fixed-bed continuous flow conditions. The results revealed that the catalytic activity of SO₄²⁻/γ-Al₂O₃ for methanol dehydration increased significantly when the content of sulfate increased to 10 wt.%, resulting in the increase in both DME selectivity and CO conversion. However, when the content of sulfate of SO₄²⁻/γ-Al₂O₃ was further increased to 15 wt.%, the activity for methanol dehydration was increased, and the selectivity for DME decreased slightly as reflected in the increased formation of byproducts like hydrocarbons and CO₂. On the other hand, when the calcination temperature of SO₄²⁻/γ-Al₂O₃ increased from 350 °C to 550 °C, both the CO conversion and the DME selectivity increased gradually, accompanied with the decreased formation of CO₂. Nevertheless, a further increase in calcination temperature to 750 °C remarkably decreased the catalytic activity of SO₄²⁻/γ-Al₂O₃ for methanol dehydration, resulting in the significant decline in both DME selectivity and CO conversion. The hybrid catalyst containing the SO₄²⁻/γ-Al₂O₃ with 10 wt.% sulfate and calcined at 550 °C exhibited the highest selectivity and yield for the synthesis of DME.     

Surface modified multi‐walled carbon nanotubes and Nafion nanocomposite membranes for use in fuel cell applications

The preparation and characterization of the nanocomposite polyelectrolyte membranes, based on Nafion, sulfonated multi‐walled carbon nanotubes (MWCNT‐SO₃H) and imidazole modified multi‐walled carbon nanotubes (MWCNT‐Im), for direct methanol fuel cell applications is described. The results showed that the modification of multi‐walled carbon nanotubes (MWCNT) with proton‐conducting groups (sulfonic acid groups or imidazole groups) could enhance the proton conductivity of the nanocomposite membranes in comparison to Nafion 117. Regarding the interactions between the protonated imidazole groups, grafted on the surface of MWCNT, and the negatively charged sulfonic acid groups of Nafion, new electrostatic interactions can be formed in the interface of the Nafion and MWCNT‐Im, which result in both lower methanol permeability and higher proton conductivity. The physical characteristics of these manufactured nanocomposite membranes were investigated by thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, water uptake, methanol permeability, and ion exchange capacity, as well as proton conductivity. The Nafion/MWCNT‐Im membranes showed the higher proton conductivity, lower methanol permeability, and, as a consequence, a higher selectivity parameter in comparison to the neat Nafion or Nafion membrane containing MWCNT‐SO₃H or ─OH functionalized multi‐walled carbon nanotubes (MWCNT‐OH) membranes. The obtained results indicated that the Nafion/MWCNT‐Im membranes could be used as efficient polyelectrolyte membranes for direct methanol fuel cell applications.     

Inorganic–organic hybrid polymers with pendent sulfonated cyclic phosphazene side groups as potential proton conductive materials for direct methanol fuel cells

A synthetic method is described to produce a proton conductive polymer membrane with a polynorbornane backbone and inorganic–organic cyclic phosphazene pendent groups that bear sulfonic acid units. This hybrid polymer combines the inherent hydrophobicity and flexibility of the organic polymer with the tuning advantages of the cyclic phosphazene to produce a membrane with high proton conductivity and low methanol crossover at room temperature. The ion exchange capacity (IEC), the water swelling behavior of the polymer, and the effect of gamma radiation crosslinking were studied, together with the proton conductivity and methanol permeability of these materials. A typical membrane had an IEC of 0.329 mmol g⁻¹ and had water swelling of 50 wt%. The maximum proton conductivity of 1.13 × 10⁻⁴ S cm⁻¹ at room temperature is less than values reported for some commercially available materials such as Nafion. However the average methanol permeability was around 10⁻⁹ cm s⁻¹, which is one hundred times smaller than the value for Nafion. Thus, the new polymers are candidates for low-temperature direct methanol fuel cell membranes.     

Synthesis, water stability and proton conductivity of novel sulfonated polyimides from 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid

A novel sulfonated diamine monomer, 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid (BAPBDS) with the high basisity and flexible structure was synthesized by direct sulfonation of 4,4′-bis(4-aminophenoxy)biphenyl (BAPB). Sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), BAPBDS and nonsulfonated diamines such as BAPB. The SPI membranes showed much higher water stability at high temperatures than other sulfonated diamine-based SPIs reported so far. Their water vapor sorption isotherm, water uptake (WU), density, dimensional change and proton conductivity σ were investigated. The SPIs showed rather isotropic dimensional changes with WU and the volume increases were slightly smaller than those estimated from the additivity. The SPIs with ion exchange capacities (IECs) of 1.9–2.7 meq/g displayed the similar relationship between σ and WU each other, which was different from those of Nafion 117 and also of the SPIs with the lower IECs. The former SPIs showed reasonably high σ values of 10⁻² S/cm or more even at WU of 25 g/100 g dry polymer under 70% RH at 50 °C, whereas the latter showed the similarly high σ values only in liquid water, but not in the nearly saturated water vapor.     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006