Residual stresses in copper-2% beryllium alloy strips

Residual-stress profiles were determined along the rolling direction in cold-rolled, annealed, and roller-leveled copper-2% beryllium alloy strips using the X-ray-diffraction technique. The data were corrected for the effects of beam penetration and subsurface-stress relaxation due to material removal. The type, magnitude and distribution of residual stresses were found to depend on the amount of cold reduction of the strips. Surface residual stresses as high as 40 percent of the material yield strength were observed, with the stress values decreasing rapidly through the depth. Corrections for the effects of both beam penetration and stress relaxation were found to be very important at higher percentages of strip cold reduction. Thermal treatments were found to significantly reduce the level of residual stress. However, mechanical treatments (roller leveling) produced no change in the magnitude of stress at the strip surface, but resulted in an irregular pattern of stress.     

A Novel Cutting Strategy for Measuring Two Components of Residual Stresses Using Slitting Method

An exact knowledge of residual stresses that exist within the engineering components is essential to maintain the structural integrity. All mechanical strain relief (MSR) techniques to measure residual stresses rely on removing a section of material that contains residual stresses. Therefore, these techniques are destructive as the integrity of the components is compromised. In slitting method, as a MSR technique, a slot with an increasing depth is introduced to the part incrementally that results in deformations. By measuring these deformations the residual stress component normal to the cut can be determined. Two orthogonal components of residual stresses were measured using the slitting method both experimentally and numerically. Different levels of residual stresses were induced into beam shaped specimens using quenching process at different temperatures. The experimental results were then compared with those numerically predicted. It was shown that while the first component of residual stress was being measured, its effect on the second direction that was normal to the first cut was inevitable. Finally, a new cutting configuration was proposed in which two components of residual stresses were measured simultaneously. The results of the proposed method indicated a good agreement with the conventional slitting.     

残余应力测定的围箍压痕法模拟

本文从同工量测方法得到启发，提出了一种新型的残余应力测试方法－围箍压痕法。采用轴对称弹塑性有限元计算模拟了围箍压痕法测量结构残余应力的力学过程，得到了围箍压痕时不同残余应力程度下材料的变形，塑性区和接触应力分布。     

Intralaboratory Repeatability of Residual Stress Determined by the Slitting Method

This paper presents repeated slitting method measurements of the residual stress versus depth profile through the thickness of identically prepared samples, which were made to assess repeatability of the method. Measurements were made in five 17.8 mm thick blocks cut from a single plate of 316L stainless steel which had been uniformly laser peened to induce a deep residual stress field. Typical slitting method techniques were employed with a single metallic foil strain gage on the back face of the coupon and incremental cutting by wire EDM. Measured residual stress profiles were analyzed to assess variability of residual stress as a function of depth from the surface. The average depth profile had a maximum magnitude of −668 MPa at the peened surface. The maximum variability also occurred at the surface and had a standard deviation of 15 MPa and an absolute maximum deviation of 26 MPa. Since measured residual stress exceeded yield strength of the untreated plate, microhardness versus depth profiling and elastic–plastic finite element analysis were combined to bound measurement error from inelastic deformation.     

Measurement of residual stress in a multi-layer semiconductor heterostructure by micro-Raman spectroscopy

Si-based multilayer structures are widely used in current microelectronics. During their preparation, some inhomogeneous residual stress is induced, resulting in com-petition between interface mismatching and surface energy and even leading to structure failure. This work presents a methodological study on the measurement of residual stress in a multi-layer semiconductor heterostructure. Scanning electron microscopy (SEM), micro-Raman spectroscopy (MRS), and transmission electron microscopy (TEM) were applied to measure the geometric parameters of the multi-layer structure. The relationship between the Raman spec-trum and the stress/strain on the [100] and [110] crystal orientations was determined to enable surface and cross-section residual stress analyses, respectively. Based on the Raman mapping results, the distribution of residual stress along the depth of the multi-layer heterostructure was suc-cessfully obtained.     

Application of X-ray diffraction, micromagnetic and hole drilling methods for residual stress determination in a ball bearing steel ring

A basic understanding of distortion problems requires the analysis of a complete manufacturing process including an almost complete overview of residual stress states in the component during each production step. To reduce the measurement time in the future, three measurements methods (X-ray diffraction, micromagnetic and blind hole drilling methods) have been used to analyze residual stress states in machined AISI 52100 ball bearing rings. X-ray diffraction was used as a state-of-the-art method for machining induced residual stresses with pronounced gradients. The ring exhibited a complex residual stress state with high tensile residual stresses at the surface, a strong gradient in depth, and also showed some variation along the outer circumference due to a superimposition of machining induced residual stresses and effects from the clamping device process. Due to this surface state, micromagnetic signals depend on the analyzing frequency. A calibration of the signals was only possible with the X-ray diffraction data. The results of the three different measurement methods correlate reasonably well.     

Experimental and Finite Element Simulation Study of Thermal Relaxation of Residual Stresses in Laser Shock Peened IN718 SPF Superalloy

An integrated experimental and modeling/simulation approach was developed to investigate and secure a quantified knowledge of the impact of high temperature exposures on the stability of residual stresses in a laser shock peened (LSP) high temperature aero-engine alloy, IN718 SPF (super-plastically formed). Single dimple LSP and overlap LSP treatments were carried out utilizing a Nd:Glass laser (λ?=?1.052 μm), and subsequent heat treatments on the LSP-treated coupons were conducted at different temperatures between 550 and 700 °C. A 3-D nonlinear finite element (FE) computational model and the rate-dependent Johnson-Cook material model were calibrated using the experimental results of residual stress from the single dimple LSP and thermal relaxation treatments, and were further extended to the overlap LSP treatment case. Both experimental and FE simulations show that: a) a high level of compressive residual stress (~700 MPa at surface) and residual stress depth (~0.4–0.6 mm) were achieved following LSP, and b) the overlap LSP treatment gave higher residual stress and greater depth. The magnitudes of the initial residual stress (and plastic strain), heating temperature and exposure time were identified as the key parameters controlling the thermal relaxation behavior. The stress relaxation mainly occurs initially before 20 min exposure and the extent of relaxation increases with an increase in temperature and a higher magnitude of the initial as-peened residual stress. In addition, in regions deeper than ~300 μm or after initial thermal exposure where the residual stress was lower than ~300 MPa, stress relaxation was found to be negligible. Kinetic analysis of the experimental thermal relaxation data based on Zener-Wert-Avrami model gave an activation enthalpy of 2.87 to 3.77 eV, which is near that reported in the literatures for volume and/or substitutional solute diffusion in Nickel. These results suggest that thermal relaxation of the LSP-induced residual stress occurs by a creep-like mechanism involving recovery, rearrangement and annihilation of dislocations by climb.     

Comparison Between Surface and Near-Surface Residual Stress Measurement Techniques Using a Standard Four-Point-Bend Specimen

Background

Determination of near-surface residual stresses is challenging for the available measurement techniques due to their limitations. These are often either beyond reach or associated with significant uncertainties.

Objective

This study describes a critical comparison between three methods of surface and near-surface residual stress measurements, including x-ray diffraction (XRD) and two incremental central hole-drilling techniques one based on strain-gauge rosette and the other based on electronic speckle pattern interferometry (ESPI).

Methods

These measurements were performed on standard four-point-bend beams of steel loaded to known nominal stresses, according to the ASTM standard. These were to evaluate the sensitivity of different techniques to the variation in the nominal stress, and their associated uncertainties.

Results

The XRD data showed very good correlations with the surface nominal stress, and with superb repeatability and small uncertainties. The results of the ESPI based hole-drilling technique were also in a good agreement with the XRD data and the expected nominal stress. However, those obtained by the strain gauge rosette based hole-drilling technique were not matching well with the data obtained by the other techniques nor with the nominal stress. This was found to be due to the generation of extensive compressive residual stress during surface preparation for strain gauge installation.

Conclusion

The ESPI method is proven to be the most suitable hole-drilling technique for measuring near-surface residual stresses within distances close to the surface that are beyond the penetration depth of x-ray and below the resolution of the strain gauge rosette based hole-drilling method.

     

Evaluation of Residual Stresses Induced by Robotized Hammer Peening by the Contour Method

Welded components suffer from high tensile residual stresses close to the weld beads. These stresses seem to be the origin of premature cracking which could result in a catastrophic rupture during operation and a reduction of the lifespan of these components. In this context, the Hydro-Québec’s Research Institute (IREQ) developed a technique of residual stresses relaxation by robotized hammer peening which makes it possible to release stresses close to surface and preserve the mechanical and dimensional properties of manufactured components. Robotized hammer peening was used to induce compressive residual stresses on initially stress free samples of austenitic stainless steel 304L. Hammer peening layers from one to nine were performed and the resulting residual stresses were evaluated thanks to the contour technique. Complete 2D residual stress fields on samples cross sections were obtained. The ability of hammer peening to relax residual stresses within welded plates was then quantified on austenitic stainless steel 304L plates welded with a 308 steel and hammer peened. These tests show the efficiency of hammer peening as a method to relax tensile residual stresses and induce compressive ones to a depth of a few millimetres. Process parameters were optimized such as the number of hammer peening layers to be applied to reduce processing time and maximization of the intensity and spatial distribution of the compressive residual stresses.     

Measuring Inaccessible Residual Stresses Using Multiple Methods and Superposition

The traditional contour method maps a single component of residual stress by cutting a body carefully in two and measuring the contour of the cut surface. The cut also exposes previously inaccessible regions of the body to residual stress measurement using a variety of other techniques, but the stresses have been changed by the relaxation after cutting. In this paper, it is shown that superposition of stresses measured post-cutting with results from the contour method analysis can determine the original (pre-cut) residual stresses. The general superposition theory using Bueckner’s principle is developed and limitations are discussed. The procedure is experimentally demonstrated by determining the triaxial residual stress state on a cross section plane. The 2024-T351 aluminum alloy test specimen was a disk plastically indented to produce multiaxial residual stresses. After cutting the disk in half, the stresses on the cut surface of one half were determined with X-ray diffraction and with hole drilling on the other half. To determine the original residual stresses, the measured surface stresses were superimposed with the change stress calculated by the contour method. Within uncertainty, the results agreed with neutron diffraction measurements taken on an uncut disk.     

Stress measurement of SS400 steel beam using the continuous indentation technique

An analytical model is presented for determining surface residual stress using continuous indentation. The elastic residual stress is assumed to have no influence on contact area or hardness and to be uniform over a volume that is several times larger than the indentation mark. A step-by-step analysis for the residual-stress-induced load difference at a given depth is outlined here and such concepts as stress interaction, stress-sensitive contact morphology, and reversible contact recoveries during a stress relaxation are described. Finally, the proposed method is applied to the interpretation of the continuous indentation results obtained from an SS400 steel beam in which controlled bending stresses are generated. The stress estimated, however, showed a high scatter due to plastic pile-up deformation. When the optically measured contact area is used as an alternative of the contact area calculated from the unloading curve, the re-evaluated stress agrees well with the already known applied stress.     

An investigation of the use of strain gages to measure welding-induced residual stresses

The measurement of weld-induced residual stress is important in structures that are subjected to cyclic loading during their service life. Depending on their magnitude, stresses can influence the rate of crack growth under cyclic loading and hence affect the life of the structure. Because the level of residual stress may change during service, measurement of these changes is necessary for accurate life prediction of the structures. The measurement of welding-induced residual stress using strain gages poses significant problems, the most important being the potential damage to the gages by high temperatures generated in the welding process. This laboratory study was undertaken to assess the suitability and signal stability of commercially available resistive strain gages for the measurement of postweld residual stresses in a submarine hull structure. Adhesively bonded and weldable-type strain gages were attached to the surface of a 35 mm thick steel plate, which was then subjected to thermal cycles similar to those encountered during welding construction of a submarine pressure hull. This paper describes the strain gage application procedure, changes in the strain gage output at end of each experimental stage and the history of changes in the residual stress.     

The Role of Residual Stresses in the Performance and Durability of Prestressing Steel Wires

Residual stresses developed during wire drawing influence the mechanical behavior and durability of steel wires used for prestressed concrete structures, particularly the shape of the stress–strain curve, stress relaxation losses, fatigue life, and environmental cracking susceptibility. The availability of general purpose finite element analysis tools and powerful diffraction techniques (X-rays and neutrons) has made it possible to predict and measure accurately residual stress fields in cold-drawn steel wires. Work carried out in this field in the past decade, shows the prospects and limitations of residual stress measurement, how the stress relaxation losses and environmentally-assisted cracking are correlated with the profile of residual stresses and how the performance of steel wires can be improved by modifying such a stress profile.     

Incremental Computation Technique for Residual Stress Calculations Using the Integral Method

The Integral Method for determining residual stresses involves making surface deformation measurements within a sequence of small increments of material removal depth. Typically, the associated matrix equation for solving the residual stresses within each depth increment is ill-conditioned. The resulting error sensitivity of the residual stress evaluation makes it essential that data measurement errors are minimized and that the residual stress solution method be as stable as possible. These two issues are addressed in this paper. The proposed method involves using incremental deformation data instead of the total deformation data that are conventionally used. The technique is illustrated using an example ESPI hole-drilling measurement.     

Method of calculating residual stresses in semicircular notches in a surface hardened hollow cylindrical specimen

A method is proposed to study the distribution of residual stresses in a semicircular notch in a hollow cylindrical specimen after advanced surface plastic deformation. The initial information used in the method is one or two experimentally determined components of the residual stress tensor in the hardened layer of the smooth specimen. The problem is solved using a finite element technique taking into account initial plastic strains, which are set in correspondence to the residual stresses according to the laws of elasticity. The effect of the hardening technology and notch depth on the distribution of residual stresses is studied. Experimental verification of the method showed that the calculated and experimental data on the stress distribution over the depth of the layer are in good agreement.     

Approximated Repair Methods for Outlier Strain Data from Hole-Drilling Residual Measurements

The current ASTM E 837 standard gives the standardized procedure for the evaluation of uniform and non uniform residual stresses, that is, stresses that do not vary and vary significantly with depth from the specimen surface, respectively. For non uniform stresses, the standard states that many small increments should be done in order to have a stable calculation of the residual stress profile. In addition, it states that irregularities as well as outlier strain points should be investigated and if necessary, the hole-drilling test should be repeated. In some applications outside the laboratory, the availability to repeat a test with outlier points is not possible. In these cases, the standard does not show the more appropriated way which should be followed to use only valid measured data (without outliers). For this reason, a stress profile corresponding to a shot peening test was simulated and one hole step was included in different hole depths as outlier point in order to evaluate the feasibility of some proposed ways of computation. These ways were: (a) following the ASTM procedure but replacing outlier strain points by linear interpolation of neighboring good ones, (b) following the ASTM procedure but replacing outlier strain points by a parabola interpolation of neighboring good ones and (c) using cumulative relaxation strain functions and only good measured points. Statistical criteria were also introduced and developed in order to identify outlier points. Results show a practical procedure to detect outlier points in experimental strain data.     

Polychromatic X-ray method for residual-stress measurements in a subsurface layer

The classical sin² method with characteristic X-rays is widely used to measure residual stress nondestructively in the steel members of a structure or a machine. With this method it is, however, difficult to measure the three-dimensional stress distribution with a steep gradient that occurs along the depth direction in a subsurface layer of the material after surface treatment such as grinding or cold rolling. This paper presents a new polychromatic X-ray method for residual-stress measurements in a subsurface layer. The relationship between the diffracted beam peak of the polychromatic X-ray and the strain along the depth direction in a subsurface layer was obtained by theoretical analysis. It was modeled by numerical simulation to obtain probable values of the parameters, and these were used along with experimental X-ray data to derive an experimental value for the stress gradient. This was compared with the values predicted from plate bending theory.Paper was presented at the 1994 SEM Spring Conference on Experimental Mechanics held in Baltimore, MD on June 6–9.     

Surface integrity of inconel-718 nickel-base superalloy using controlled and natural contact length tools. part I: Lubricated

The surface integrity of inconel-718 nickel-base superalloy was investigated using orthogonal cutting at various cutting speeds, depths of cut and chip-tool contact lengths under lubricated conditions. The experimental work involved the determination of residual stress, plastic strain and microhardness distribution in the surface region and the examination of the surface and subsurface using scanning electron and optical microscopy. Both residual stresses and plastic strains decreased and the quality of the mechined surface improved with an increase in cutting speed, a decrease in depth of cut and with tools having controlled chip-tool contact lengths. The results were interpreted in terms of the variation in shear plane length and consequently the variation in tool forces with cutting conditions.     

Delayed presetting of helical springs

Abstract

This article establishes the calculation of remaining deformation and residual stress for helical springs after long-lasting presetting process. The article extends the model for the immediate presetting process accounting the creep deformation of the spring. The method is based on plasticity theory for the instant flow overexposed by the relaxation over the long-term presetting. In this article, the following method is used. The plastic deformation of the helical spring with the circular cross section occurs instantly. If the shortening of the spring in the tool holder persists, the relaxation of stresses occurs and the force of the spring reduces. As the consequence, after the elastic unloading of the long-time presetting, the residual stresses spring reduce gradually with the squeezing time as well. The final length of the springs considerably shortens with the increasing preset duration. The advantage of the discovered closed form solutions is the calculation without the necessity of complex finite-element simulation of spring length loss and residual stresses after presetting process. The analytical expressions are proposed and the exact calibration applied for evaluation of factors for presetting processes.     

Laser surface-contouring and spline data-smoothing for residual stress measurement

We describe non-contact scanning with a confocal laser probe to measure surface contours for application to residual stress measurement. (In the recently introduced contour method, a part is cut in two with a flat cut, and the part deforms by relaxation of the residual stresses. A cross-sectional map of residual stresses is then determined from measurement of the contours of the cut surfaces.) The contour method using laser scanning is validated by comparing measurements on a ferritic steel (BS 4360 grade 50D) weldment with neutron diffraction measurements on an identical specimen. Compared to lower resolution touch probe techniques, laser surface-contouring allows more accurate measurement of residual stresses and/or measurement of smaller parts or parts with lower stress levels. Furthermore, to take full advantage of improved spatial resolution of the laser measurements, a method to smooth the surface contour data using bivariate splines is developed. In contrast to previous methods, the spline method objectively selects the amount of smoothing and estimates the uncertainties in the calculated residual stress map.