热压处理对Nd0.7Sr0.3MnO3陶瓷磁电输运影响

在温度1273 K、压强9 GPa条件下对固相烧结Nd_0.7Sr_0.3MnO₃陶瓷样品进行热压处理. 结果发现, 处理后样品的晶体结构和空间群没有改变, 但晶胞参数和结构参数, 特别是样品的显微结构发生了很大变化. 这些变化对样品的磁电输运产生显著影响: 在磁性上, 热压样品的低温饱和磁矩减小并出现磁矩排列弥散特点; 在电输运方面, 当负载电流小于1.5 mA时, 与烧结样品一样, 热压样品不产生电致电阻 (ER) 效应, 并在金属-绝缘体转变点出现最大磁电阻 (MR). 但在低温下, 热压样品仍有较大MR值. 当负载电流超过1.5 mA时, 热压样品原R-T曲线中的电阻峰替变为一电阻平台, 且随负载电流增大, 平台逐渐宽化, 阻值减小, 出现ER行为. 有趣的是, 在外磁场作用下, 电阻平台随外场增大逐渐变窄、消失并又演变为一电阻峰. 这些奇特的输运行为除与热压处理导致样品晶粒绝缘化有关外, 可能还与热压导致粒间相的形成有关.     

K3C60取向相变的同步辐射光电子谱研究

在190K,220K和300K3个不同温度下测量了K₃C₆₀单晶薄膜沿[111]方向发射的同步辐射角分辨光电子谱.样品温度为190K时,能够观察到导带有规律的角散,并且带结构与已报道的温度为150K时的结果基本一样.而在220K附近,导带的许多子峰消失,色散不再存在.这两个温度的实验结果与K₃C₆₀在200K存在取向相变相符合,并且可在反铁磁Ising模型基础上得到理解.这种模型的定量分析结果还首次对K₃C₆₀在200K的相变机理作出了解释,即相变是由低温下的一维无序取向结构转变为200K以上的双取向结构畴与无序分子(约占40%)的混合.室温光电子谱与低温下的结果显著不同,对应于C₆₀分子取向在室温附近的动态无序.     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

Pd/Ag掺杂的La0.67(Ca0.65Ba0.35)0.33MnO3体系电特性和磁电阻增强效应

系统研究了xAg-La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃和xPd-La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃(xAg-LCBMO和xPd-LCBMO)两种复合体系的电特性和磁电阻特性. 结果发现,Pd和Ag的掺杂都引起电阻率的大幅降低和峰值电阻率温度的升高,这主要源于晶粒边界/表面良导体金属晶粒的析出. 另外,Pd和Ag的掺杂都引起室温磁电阻的大幅增强. 尤其是27%摩尔比的Ag掺杂诱导了高达70%的室温磁电阻,几乎是未掺杂母体LCBMO的10倍,而27%摩尔比的Pd掺杂诱导产生了更高的磁电阻,约170%. 磁电阻的大幅增强,与良导体金属掺杂引起的样品电阻率的降低有关. 另一方面,晶粒表面/边界Mn离子与Pd离子接近诱导Pd离子的自旋极化对磁电阻的增强起了重要的促进作用.     

Tb2Fe15.5Cr1.5化合物的本征磁致伸缩

通过x射线衍射及磁测量手段研究了Tb₂Fe_15.5Cr_1.5化 合物的热膨胀性质及本征磁致伸缩性质.研究结果表明Tb₂Fe_15.5Cr _1.5化合物在293—672K的温度范围内具有六角相的Th₂Ni_{17型结构.在432—522K的温度范围内具有负热膨胀 性质，其平均热膨胀系数=-157×10^-5/K.对本征磁致伸缩的研究结果表明Tb2Fe15.5Cr1.5化合物中存在着较强的各向异性的本 征磁致伸缩，293K时其本征体磁致伸缩约为84×10^-3，晶格畸变主要发生在c 轴方向上.磁测量研究结果表明Tb2Fe15.5Cr1.5化合物的居里温度约为494K，比其母 合金Tb2Fe17高约80K.}     

Ce2-xDyxFe17合金的磁熵研究

研究了Ce_2-xDy_xFe₁₇(x=0.0,0.3,0.5,1.0)系列合金在77—298K温区范围磁熵变,发现Ce_2-xDy_xFe₁₇系列合金有较大的磁熵变,居里温度可通过离子替代而改变,是一种可供选择的室温磁致冷材料.     

Fe3O4/MgO(100)薄膜的激光分子束外延与磁电学性能

 采用激光分子束外延方法,以烧结α-Fe₂O₃/为靶材,在MgO（100）基底上制备了Fe₃O₄薄膜。通过反射高能电子衍射原位观察了薄膜生长前后的表面结构,结果表明所生长的Fe₃O₄薄膜表面平整。经显微激光拉曼光谱和X光电子能谱分析证实所得薄膜表面成分为纯相Fe₃O₄。磁电学性能采用多功能物性系统测量,结果表明：当温度降至100 K附近时,薄膜电阻率有较大增加,Verwey相转变的范围变宽而且不明显,说明反向晶粒边界的存在;在7 160 kA·m^-1的磁场下,室温磁电阻达到-6.9%,在80和150 K温度下磁电阻分别达到-10.5%和-16.1%;薄膜的室温饱和磁化强度约为260 kA·m^-1,其矫顽磁场约为202 kA·m^-1。     

一级相变材料Mn1.2Fe0.8P0.4Si0.6的热磁发电性能

本文报道把热能直接转换电能的热磁发电技术所用一级相变新材料Mn_1.2Fe_0.8P_0.4Si_0.6的磁性和热磁发电性能.用高能球磨机械合金化技术和固相烧结合成方法制备了Mn_1.2Fe_0.8P_0.4Si_0.6化合物.磁性测量结果表明,该化合物呈现从铁磁状态变为顺磁状态的一级相变,居里温度为337K,并伴随巨大的磁化强度的变化.根据该材料的这一特性,设计制作了热磁发电演示装置,测定了热流引起材料的相变而产生的电流,并研究了固定磁场中热致磁转变产生的电流随热流温度和样品质量的变化.研究结果表明Mn_1.2Fe_0.8P_0.4Si_0.6化合物具有很好的热磁发电性能,可作为热磁发电材料.     

Sm(CobalFe0.1Cu0.1Zr0.033)6.9高温永磁合金的矫顽力

对Sm(Co_balFe_0.1Cu_0.1Zr_0.033)_6.9合金, 经810℃等温时效后以0.5℃/min逐渐冷却, 在600℃-400℃温度区间淬火, 研究了不同淬火温度下的磁滞回线、磁畴和矫顽力温度系数β. 发现时效600℃淬火后磁滞回线出现台阶状, 说明畴壁中应存在两处钉扎. 随淬火温度的降低, 合金的室温矫顽力显著增加, 磁滞回线的台阶消失. 通过磁畴形貌发现时效600℃淬火后的磁畴接近条形畴, 1:5相中Cu分布相对均匀, 形成的畴壁钉扎较弱, 从而使磁滞回线出现台阶, 决定矫顽力的畴壁钉扎位于两相界面处; 随时效淬火温度的降低, 磁畴逐渐细化, 畴壁1:5相中的畴壁能降低, 形成了较强的内禀钉扎, 并决定材料的矫顽力, 两相界面处的畴壁钉扎被掩盖. 对不同温度淬火合金的高温矫顽力研究表明, 最强的畴壁钉扎位于两相界面处时, 矫顽力随温度升高逐渐增加, 矫顽力出现温度反常现象; 最强的畴壁钉扎位于1:5相中心时, 矫顽力随温度升高逐渐衰减. 当测试温度达到500℃后不同淬火温度样品的矫顽力几乎相同, 此时最强畴壁钉扎均在两相界面处.     

Gd0.55Sr0.45MnO3薄膜光诱导电阻变化特性研究

分别采用固相反应和脉冲激光沉积的方法制备了电荷-轨道有序态锰氧化物Gd_0.55Sr_0.45MnO₃块材和多晶薄膜, 研究了薄膜在光诱导作用下的电阻变化特性. 实验结果表明该薄膜在整个测量温度范围内表现出了半导体型导电特性. 利用变程跳跃模型拟合电阻温度关系可知, 其电荷有序态转变温度为70 K. 激光作用致使薄膜电阻减小, 当激光功率度为40 mW/mm²时, 最大光致电阻相对变化值可达99.8%, 且在8 s的时间内达到了平衡态, 温度对其影响很小; 当激光功率度为6 mW/mm²时, 获得的最大光致电阻相对变化值为44%, 而且时间常数随温度的升高而增大, 这主要是由于光诱导和热扰动共同作用的结果.     

Optical spectroscopy of Ca3Sc2Si3O12, Ca3Y2Si3O12 and Ca3Lu2Si3O12 doped with Pr

The silicates Ca₃Sc₂Si₃O₁₂, Ca₃Y₂Si₃O₁₂ and Ca₃Lu₂Si₃O₁₂, both undoped and doped with Pr³⁺ ions, have been synthesized by solid-state reaction at high temperature. The luminescence spectroscopy and the excited state dynamics of the materials have been studied upon VUV and X-ray excitation using synchrotron radiation. All doped samples have shown efficient 5d-4f emission upon direct VUV excitation of 5d levels, but only Ca₃Sc₂Si₃O₁₂:Pr³⁺ shows luminescence upon interband VUV or X-ray excitation. The VUV excited emission spectra of Ca₃Y₂Si₃O₁₂:Pr³⁺ and Ca₃Lu₂Si₃O₁₂:Pr³⁺ show features attributed to emission from two distinct sites accommodating the Pr³⁺ dopant. The decay kinetics of the Pr³⁺ 5d-4f emission in Ca₃Sc₂Si₃O₁₂:Pr³⁺ upon VUV excitation across the band gap are characterized by decay times in the range 25-28 ns with no significant rise after the excitation pulse. They appear to be faster upon X-ray irradiation than for VUV excitation. Weak afterglow components are attributed to defect luminescence.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

La0.67Ca0.33MnO3薄膜皮秒光电效应

在1064 nm波长脉冲激光（脉宽25 ps）的照射下，钙钛矿氧化物薄膜La0.67Ca0.33MnO3/SrTiO3具有超快光电效应，对激光脉冲显示ps量级的响应时间，上升沿响应时间300 ps，半高宽700 ps，同时，对激光能量的响应灵敏度为500 mV/mJ。     

合成反铁磁Ni81Fe19/Co90Fe10/Ru/Co90Fe10/Ni81Fe19的研究

采用直流磁控溅射方法制备了一系列的合成反铁磁及以其为自由层的自旋阀.研究发现,在Ni₈₁Fe₁₉与Ru层之间插入适当厚度的Co₉₀Fe₁₀层后,可有效地提高合成反铁磁两磁性层间的反铁磁耦合强度,得到具有饱和场H_s更高、饱和磁化强度M_s更低、热稳定性更好的合成反铁磁.另外,以这种合成反铁磁作自旋阀的自由层时,可有效提高自旋阀的稳定性. 关键词： 合成反铁磁 退火 自旋阀     

Depolarization currents in the Na0.5Bi8.5Ti2Nb4O27 and Na0.5Bi8.5Ti2Ta4O27 layered ferroelectrics

The influence of the prehistory on the electrical properties of layered ferroelectrics is investigated. It is established that the heating of short-circuited samples of the nonpolarized ceramic material Na_0.5Bi_8.5Ti₂Nb₄O₂₇ leads to the appearance of maxima of the current at temperatures below the Curie point only in the case of preliminary ageing of the samples. Original Russian Text ? A.I. Burkhanov, Yu.V. Kochergin, K. Bormanis, A. Kalvane, M. Dambekalne, 2009, published in Fizika Tverdogo Tela, 2009, Vol. 51, No. 7, pp. 1393–1394.     

Structure and magnetic order in La0.7Ca0.3Mn0.5Co0.5O3 and La0.8Sr0.2Mn0.5Co0.5O3 perovskites

In this paper we report the study of the perovskites La_0.7Ca_0.3Mn_0.5Co_0.5O₃ and La_0.8Sr_0.2Mn_0.5Co_0.5O₃ by neutron powder diffraction at various temperatures and magnetization measurements in zero applied field and at low cooling regimes. The replacement of half Mn by Co in La_0.7Ca_0.3MnO₃ and La_0.8Sr_0.2MnO₃ destroys their long-range ferromagnetism exhibiting a cluster glass ferromagnetic order similar to the one observed in many cobaltites.     

Cross section determination for the reaction K+p → K+pπ+π−π0 and K+π+π+π−n at 8.2 and 16 GeV/c

The cross sections for the reactions: (a) K⁺p → K⁺pπ⁺π^?π⁺ and (b) K⁺p → K⁺π⁺π⁺π^?n have been determined at 8.2 and 16 GeV/c with the following results:at 8.2 GeV/c: (a) 0.99 ± 0.07 mb, (b) 0.41 ± 0.04 mb;at 16 GeV/c: (a) 0.72 ± 0.05 mb, (b) 0.28 ± 0.05 mb.Using the available data at other energies, the cross-section dependence of these reactions on the incident momentum is discussed.     

Appearance of an inhomogeneous superconducting state in La0.67Sr0.33MnO3-YBa2Cu3O7-La0.67Sr0.33MnO3 trilayers

An experimental study of proximity effect in La_0.67Sr_0.33MnO₃-YBa₂CU₃O₇-La_0.67Sr_0.33MnO₃ trilayers is reported. Transport measurements on these samples show clear oscillations in critical current (I _c) as the thickness of La_0.67Sr_0.33MnO₃ layers (d _F) is scanned from ∼50 ? to ∼ 1100 ?. In the light of existing theories of ferromagnet-superconductor (FM-SC) heterostructures, this observation suggests a long range proximity effect in the manganite, modulated by its weak exchange energy (∼2 meV). The observed modulation of the magnetic coupling between the ferromagnetic LSMO layers as a function of d _F, also suggests an oscillatory behavior of the SC order parameter near the FM-SC interface.      

Phase formation and characterization of Sr3Y2Ge3O12, Sr3In2Ge3O12, and Ca3Ga2Ge3O12 doped by trivalent europium

This work reports on the phase formation during a solid-state reaction of Eu³⁺-doped garnets with the general formula A₃B₂Ge₃O₁₂ (A=Ca, Sr and B=Ga, In, Y) and their luminescent properties. It is shown by XRD and DTA/TG experiments that the garnet-phase formation is completed at 1100-1200 °C. Moreover, it turned out that the position of the oxygen to europium charge-transfer band and the intensity of the forbidden 4f-4f transitions of Eu³⁺ is dependent on the covalent interaction between the Eu³⁺ activator and the surrounding oxygen anions. The investigated red-emitting luminescent materials show high lumen equivalents and deep red emission at the same time, which makes them attractive for the application in LEDs (light emitting diodes), in particular for near UV-emitting LEDs.     

Electrical transport and superconductivity in the Al2O3-Bi2Sr1.8Ca1.2Cu2Oy and MgO-Bi2Sr1.8Ca1.2Cu2Oy composites

We have measured the resistivities of Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites with the nominal Bi₂Sr_1.8Ca_1.2Cu₂O_y volume fraction, ₂₂₁₂, ranging from 0.15 to 1.00. For the Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu ₂O_y composites, we find for the samples with ₂₂₁₂≥0.6 that the superconducting transition temperature, T_c, is not disturbed by the addition of Al₂O₃. For ₂₂₁₂<0.3, no zero-resistivity state is observed. For the MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites, T_c is barely disturbed for the samples with ρ₂₂₁₂≥0.7. No superconducting state is observed for the samples with ρ₂₂₁₂<0.35. The variation of (300 K) with ρ₂₂₁₂ indicates a three-dimensional percolating Bi-Sr-Ca-Cu-O matrix occurring at ρ₂₂₁₂≈0.19 and ≈0.15 in Al₂O₃-Bi₂Sr_1.8Ca_1.2 Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y, respectively. Both resistivity and magnetization measurements suggest that the reactions of Bi₂Sr_1.8Ca_1.2Cu₂O_y with MgO are weaker than with Al₂O₃.